Installation Manual 78-88 Chevrolet G ody Compressor Upgrade Kit - 123-2004
Congratulations... You have just purchased the highest quality, best performing /C system upgrade ever designed for your Classic Vehicle. To obtain the high level of performance and dependability our systems are known for, please pay close attention to the following instructions. Our installation steps and procedures are derived from a long history of research and development and the combined experience achieved through thousands of successful installations (and feedback from customers like you). Please remember that our #1 goal is that you ll have a successful installation and a system that performs at a very high level for many years to come. efore starting, read the instructions carefully, from beginning to end, and follow the proper sequence. On the next page you ll find a safety and general checklist that you should read before starting your installation. gain, thank you from our entire staff. 2 www.classicautoair.com 866.435.7801
Pre-Installation: efore beginning the installation, check the shipping box for the correct components. If your vehicle has been or is being modified, some procedures will need to be adjusted to fit your particular application. basic cleaning of the engine compartment before beginning will make things go more smoothly. Check condition of engine mounts. Excessive engine movement can damage hoses to /C and/or heater. DISCONNECT THE TTERY FIRST DISCHRGE THE SYSTEM NEXT; You will want to have your system evacuated of all remaining refrigerant according to local laws. n /C service shop can handle this for you. TOOLS/MTERILS REQUIRED: Standard and Metric Socket Set, ( set of standard and metric ratcheting wrenches are suggested for the compressor installation), Magnet (Reach Tool), (2x) Medium djustable Wrenches, Flat Screwdriver, Wire cutter w/ crimper, Flat lade Scraper, Tape or Caps, Schrader valve removal tool, and Spray dhesive or Contact Cement (If replacig Evaporator). PLESE NOTE! it s critical that LL COMPONENTS are clean and free of contamination. Damage to components as a result of contamination will not be covered under warranty. Important Notes: Use one or two drops of oil (supplied with your kit) on LL O-rings, and threads. ll capped fittings MUST remain covered until actual connection of the fitting to prevent contamination. Use two adjustable wrenches on all O-ring connections, these should be tightened to 10-15 ft/lbs which is hand tight plus ¼ turn. Over tightening could cause splitting of the O-ring. Carefully thread fittings. Fittings will thread easily, therefore if there is resistance, back off and re-align to avoid cross-threading. e careful not to over tighten. Should you have any technical questions, call us immediately, we will be glad to assist you. Our toll-free number is listed on every page, we re here to help! 3 YOU CN NOW EGIN THE INSTLLTION... www.classicautoair.com 866.435.7801
THESE RE THE PRTS FOR YOUR COMPRESSOR UPGRDE KIT Compressor Mount Kit PN# 06-297 ccumulator PN# 12-215 Compressor PN# 5-151 Orifice Tube PN# 15-209 Clutch Cycling Switch PN# 16-200 Straight (High Side- Red Cap) 134a dapter PN# 14-201-1 4 O-Rings and Lubricant Oil PN# 05-400 V - elt PN# 10-201 Straight (Low Side - lue Cap) 134a dapter PN# 14-122-2 Suction Hose and Discharge Hose www.classicautoair.com 866.435.7801
CCUMULTOR REMOVL Disconnect the plug from the pressure cycling switch (Figure 1). Disconnect Suction hose from accumulator (Figure 1). Remove the accumulator bracket hardware and small clamp con- REMEMER! E D necting to the liquid line (Figure 1C) Disconnect the accumulator to evaporator outlet fitting (Figure 1D) LOOSEN ND TIGHTEN HOSE ENDS WITH TWO WRENCHES Remove accumulator and retain brackets for re-assembly Disconnect the liquid hose (solid tubing) from the inlet fitting of the evaporator core (Figure 1E) Once the liquid line is disconnected you will see the orifice tube/ filter inside, this part will need to be removed (Figure 2). C Cover ends of evaporator fittings with tape to prevent contamination. (Figure 1) Note the orientation of the orifice tube in the evaporator inlet, as the new tube will be installed in the same orientation. There is a tool made for removal of stuck orifice tubes, typically it can be carefully removed with a pair of needle nose pliers. L I Q U I D L I N E 5 (Figure 2) www.classicautoair.com 866.435.7801
COMPRESSOR REMOVL Compressor instructions below are specific for the later model R4 compressor, however the steps are similar to earlier models that have an early-style 6 compressor. Remove the 6 Compressor and all of it s brackets as with the R4 Remove electrical plugs from compressor, move to side for later connection. In addition, you will need to remove block mounted sensor wire that is routed through the compressor bracket. It can be re-attached after the new compressor is attached. Loosen smog pump and alternator tensioner bolts and remove belts Remove compressor tensioner bolts and remove compressor belt C Disconnect Discharge hose, (hose from compressor to condenser)from condenser. (Figure 3C) (Figure 3) Detach hose manifold from rear of OEM compressor, (Figure 3) by removing the bolt in the center of the manifold. Remove hose assembly from vehicle. ( e careful not drip remaining coolant on painted surfaces) Remove long brace that attaches to the intake manifold stud. (Figure 3) Remove Compressor from factory brackets by removing tensioner bolts and lower pivot bolt on the front and back of the compressor. Remove tensioner bolts from power steering brackets. Loosen pivot bolt on bottom of steering pump. Remove three remaining brackets from engine 6 www.classicautoair.com 866.435.7801
COMPRESSOR INSTLLTION This Kit and racket were designed as a replacement for factory parts. If your vehicle has been modified with items such as Tall Valve covers, you will need to refer to the compressor installation instructions from your included alternate bracket. Install the lower compressor mount to the head using (3x) 1 bolts and the (3x) 1/4 spacers. Spacers will mount between head and lower mount. (Figure 4) The left bracket bolt will fit through the factory power steering bracket, and then route through the new bracket and spacer. Now tighten the power steering pump and confirm belt has proper tension. (Figure 4) ttach the upper compressor mount to the lower compressor mount using the (3x) 3/4 bolts with the lock washers and flat washers on top of the upper mount. (Figure 5) ttach loosely, as this upper plate will need to be moved for belt align ment in future steps ttach the T-adjuster to the &F (facing unit) of the compressor using the 5 bolt and nylock nut. (Figure 6) Do not tighten completely until later step. (Figure 4) ENGINE C It is critical that the fill plug is mounted upwards once the compressor is mounted. Place one of the T-adjuster 1/2 nuts on the adjuster to the end of the threads to allow for maximum adjustment. lign the compressor tabs D&G with the upper bracket fixed spacer. (Figure 5C) ttach using the 1 spacer at the rear of the fixed spacer using the 5 bolt and nylock nut. (Figure 8) Do not tighten completely until later step. 7 (Figure 5) FENDER D www.classicautoair.com 866.435.7801
COMPRESSOR INSTLLTION CONT. Lower the compressor and T-adjuster into the rear adjuster hole. (Figure 5D, 6C) Visually align the compressor pulley with the water pump pulley and the power steering pulley. Tighten one of the three 3/4 upper plate bolts. Raise the compressor, confirm the that the leading edge of the upper and lower brackets are parallel. (Figure5) Tighten the remaining of the three bolts and lower compressor back into mount. Install the included belt, and then tension with the installed nut on the T-adjuster. Install the second 1/2 nut and lock washer to the bottom of the T-adjuster bolt to lock the compressor at the correctly tensioned setting. (Figure 6) C Tighten nylock nuts on 5 compressor mount bolts The compressor wire will need to be connected to the OEM wiring. Find the compressor wire that was originally connected to the OEM compressor and cut the connector off. Shave the insulation off the end of the green wire and crimp the female bullet connector, then connect the male bullet connector from the compressor. DONT FORGET! REMEMER! REMEMER! If the car was equipped with a switch mounted in the back of the compressor, it will be eliminated. Find the wiring and cut the connector off. Shave the insulation off the end of both wires and crimp together using the supplied butt connector. Place back in wire loom. LURICTE LL O-RINGS WITH 2 DROPS OF MINERL OIL LEVE LL SHIPPING CPS ON UNTIL FINL INSTLLTION LOOSEN ND TIGHTEN HOSE ENDS WITH TWO WRENCHES 8 ww w.classicautoair.com 866.435.7801
ORIFICE TUE/134 DPTER Install new orifice tube into evaporator inlet fitting with lubricated O-rings (Figure 2). With a Schrader valve removal tool, remove the Schrader valve from D the liquid line. It will not be used with the 134a adapter. Screw the 134a adapter (Red Cap) onto the R12 port on the liquid line without oil, (adapter has thread-lock on threads). ttach the liquid line to the inlet fitting of the evaporator - It may be necessary to manipulate the line slightly to fit into place. C CCUMULTOR INSTLLTION Screw provided pressure cycling switch into the rear port on the top of the accumulator. (Figure 7) *See note at end of instructions - Page 10 With a Schrader valve removal tool, remove the Schrader valve from the other accumulator port. It will not be used with the 134a adapter. Screw the 134a adapter (lue Cap) onto the R12 port on the accumulator without oil, (adapter has thread-lock on threads). Slide the new accumulator into the brackets, but do not tighten screws until evaporator connection is complete. Tighten evaporator fitting with Lubricated O-ring to accumulator. (Figure 7) 9 (Figure 7) Tighten the accumulator bracket screw, (Figure 7C) and small hose clamp to lower evaporator fitting. Fitting may need to be carefully manipulated to fit into clamp. (Outlet fitting of accumulator will be attached to suction hose in a later step) Plug the pressure cycling switch harness into the installed switch DONT FORGET! LURICTE LL O-RINGS WITH 2 DROPS OF MINERL OIL REMEMER! LEVE LL SHIPPING CPS ON UNTIL FINL INSTLLTION REMEMER! LOOSEN ND TIGHTEN HOSE ENDS WITH TWO WRENCHES ww w.classicautoair.com 866.435.7801
HOSE CONNECTION Loosely attach the Suction hose with lubricated O-Ring to the S port of the compressor and the other end to the accumulator fitting. (Figure 8) Loosely attach the Discharge hose with lubricated O-Ring to the D port of the compressor and the other end to the inlet fitting of the condenser. (Figure 8) fter proper routing of the hoses and checking for clearance, tighten fittings on compressor. (Figure 9) FINL STEPS Take a look around at your installation and check all fittings and bolts for tightness, and make sure nothing is routed in a way to obstruct any moving parts. You can reconnect the battery at this time. PLESE NOTE! it s critical that LL COMPONENTS are clean and free of contamination. Damage to components as a result of contamination will not be covered under warranty. * Pressure Cycling Switch Note: Your kit comes with an adjustable pressure cycling switch. e sure to advise the charging technician this will need to be tuned to your vehicle and 134a requirements for proper cooling. 10 (Figure 8) (Figure 9) ww w.classicautoair.com 866.435.7801