7C1550 COBB Tuning R35 GT-R Silicone Hose Kit Install Instructions
|
|
- Alyson Walker
- 5 years ago
- Views:
Transcription
1 7C1550 COBB Tuning R35 GT-R Silicone Hose Kit Install Instructions Nissan GT-R (R35) Silicone Hose Kit Congratulations on your purchase of the COBB GT-R Silicone Hose Kit for your Nissan GT-R. The following instructions should assist you through your installation process. Please read them first BEFORE beginning the install and familiarize yourself with the steps and tools needed. If you feel that you cannot properly perform this installation, we HIGHLY recommend you take the vehicle to a qualified and experienced automotive technician. Part List 2-Post MAF hose for GTR 2-Throttle Body Hose 2-Upper Hose 1-LH Hot Hose 1-LH Cold Hose 1-RH Cold Hose 1-RH Hot Hose 2-Turbo Inlet 4-T-Bolt Clamp GTR63 8-T-Bolt Clamp GTR74 8-T-Bolt Clamp GTR81 2-Stainless Clamp 40mm 2-44mm Hose Clamp 1-Metal License Plate Frame, Thanks!
2 Tools Needed Flat Head & Phillips Head Screwdrivers Socket Wrench (We recommend 3/8 drive) 12 Extension for Socket Wrench 10mm & 12mm Socket 10mm Boxed End Wrench (ratcheting preferred) Needle Nose Pliers (to help remove plastic fasteners) Silicon Spray (optional) Bumper/undertray removal 1 Safely & securely raise the car on a lift or jack stands and remove the front wheels. 2 The front bumper will be removed with the under tray as one piece. Move underneath the car and remove the ten plastic fasteners, two 10mm bolts, and two 12mm bolts. 3 You will now need to remove the front portion of both left and right side inner fender liners by removing the one screw and nine remaining plastic fasteners per side. Please be sure to collect all hardware so that you do not kick it around as you are working on the vehicle.
3 4 With the fender liners removed you may now to access and remove three 10mm bolts on each end of the bumper. You will also need to disconnect both side marker lights.
4 5 Move to the engine bay and remove the plastic radiator cover by removing the eight plastic fasteners.
5 6 Now remove the six plastic fasteners underneath the radiator cover.
6 7 Disconnect the connector that goes to the airbag sensors in the front bumper (JDM only). At this time you may also want to apply protective tape along the front fenders (as pictured below) to prevent them from being damaged while removing and installing the front bumper. 8 You should now be able to remove the entire front bumper and under tray as one piece.
7 Stock intercooler pipe removal and Cobb Silicone Hose installation 1 You can go about replacing the stock rubber intercooler hoses in many different ways. We recommend you replace one side of the motor at a time, starting from the throttle body and working your way down. We do not recommend you tighten any of the t-bolt clamps until all of the silicone hoses are installed. This will allow you to fine tune the fitment by rotating the silicone one piece at a time until everything fits nicely. The diagram below will show you which silicone piece goes where and what size clamps to use.
8 2 You can align the t-bolt clamps in several different positions; some may work better than others. When installing the t-bolt clamps always assume a possibility of the pipes blowing off exists and install them in a way that they will be accessed easily with minimal work involved. The below pictures show the orientation in which we have installed the clamps with the best fitment for future adjustments/tightening. The first picture is of the right side upper intercooler pipes. Make sure that the t-bolt clamps at the throttle body are rotated down enough that they have sufficient room to clear the hood while the motor twists under acceleration and deceleration.
9
10 3 The only way to easily access the t-bolt clamps when installing the lower intercooler pipes is to remove the inner fender liner. With the stock lower intercooler pipe removed you will want to loosen the 12mm bolt that secures the cast aluminum lower intercooler pipe and replace the small stock rubber hose on the turbo outlet with the silicone replacement. Make sure that the top clamp on the upper pipe is rotated inward enough to clear the fender liner when it is reinstalled. 4 Unfortunately, the only way to access the clamp that secures the intercooler pipe to the top of the intercooler is to remove the front bumper. Make sure that you get this one nice and tight because you don't want to have to remove the bumper again if it comes off. During this step, it may allow for more room if you remove the four plastic fasteners that attach the ducting to the oil cooler and remove it.
11 5 The left side of the upper intercooler pipe clamps will be installed in the same orientation as the right side. Refer to steps 2 and 3 for specific installation notes.
12 6 The lower intercooler pipe clamps will be oriented the same as the lower right side clamps with the exception of the clamp that secures the intercooler pipe to the turbo outlet. We ve found it easier to access this clamp from inside the engine bay rather than through the fender well. It also makes it easier to access if it comes off rather than pulling the wheel and fender liner.
13 This is the clamp that secures the intercooler pipe to the left side turbo outlet as viewed from above the engine bay. Make sure that the clamp is rotated properly so that it does not interfere with the lower radiator hose.
14 7 This is the clamp that secures the intercooler pipe to the top left intercooler outlet. Once again, make sure this one is tight because it will require removing the entire front bumper to reinstall if it comes off.
15 8 Now take several minutes to go over and double check that all of the clamps are securely tightened and that they are all properly oriented and do not interfere with any bodywork, hoses, wire harnesses, etc. Start the car and warm it up making sure that the car has a stable idle. If you find the idle becomes inconsistent or fluctuates this may be a sign of a boost leak or post MAF leak, recheck all fittings and connections until the problem has been located. Testing the intake and charge piping with a pressurizing smoke machine is highly suggested if you have access to one. 9 Reinstall the bumper, under tray, fender liners, and wheels in the reverse order in which they were removed. 10 Enjoy your GT-R Silicone Hose Kit!
Subaru Front Mount Intercooler Kit STI Subaru Front Mount Intercooler Kit STI
Subaru Front Mount Intercooler Kit STI 2008-2014 715500 Subaru Front Mount Intercooler Kit STI 2008-2014 Congratulations on your purchase of the Subaru Front Mount Intercooler Kit STI 2008-2014. The following
More informationHARD PIPE KIT
701550 HARD PIPE KIT 2014 Ford Fiesta ST Congratulations on your purchase of the COBB Hard Pipe Kit for your 2014+ Ford Fiesta ST. The following instructions will assist you through your installation process.
More informationMAZDASPEED3 Intercooler Instructions
MAZDASPEED3 Intercooler Instructions Congratulations on your purchase of the COBB Tuning Front Mount Intercooler System for your 2007-2009 Mazdaspeed3. The following instructions should assist you through
More informationCOBB Tuning MAZDASPEED6 SF Intake System. Install Instructions
781500 COBB Tuning MAZDASPEED6 SF Intake System Install Instructions Congratulations on your purchase of the COBB Tuning SF Intake System. The following instructions will assist you through your installation
More information7B1210 COBB BMW N54 Charge Pipe
7B1210 COBB BMW N54 Charge Pipe Installation Instructions Congratulations on your purchase of the COBB BMW N54 Charge Pipe for your BMW. The following instructions will assist you through your installation
More informationFocus ST Carbon Fiber Intake
791400 - Focus ST Carbon Fiber Intake 791400 COBB Focus ST Carbon Fiber Intake Congratulations on your purchase of the COBB Tuning Carbon Fiber Intake System! The following instructions will assist you
More informationCOBB 3-Port Electronic Boost Control Solenoid
COBB 3-Port Electronic Boost Control Solenoid MazdaSpeed3/Mazdaspeed6 Congratulations on your purchase of the COBB Tuning 3-Port Electronic Boost Control Solenoid. The following instructions will assist
More informationParts List See cover Page
Thank you for purchasing the CorkSport Front Mount Intercooler Kit for the 2010-2013 Mazdaspeed 3. Keep your BAT s under check with the CorkSport FMIC Kit with the small or large intercooler. Please let
More informationCOBB 3 SF INTAKE SYSTEM
COBB 3 SF INTAKE SYSTEM 2015 Mustang Ecoboost Congratulations on your purchase of the COBB 3 SF Intake System for your 2015 Mustang Ecoboost. The following instructions will assist you through your installation
More informationCOBB Catback Exhaust
591100 COBB Catback Exhaust 2013 Ford Focus ST Congratulations on your purchase of the COBB Catback Exhaust for your 2013 Ford Focus ST. The following instructions will assist you through your installation
More informationNissan R35 GTR Intercooler Pipe Kit w/ Cold Air Intake Installation Instructions
Nissan R35 GTR Intercooler Pipe Kit w/ Cold Air Intake Installation Instructions 1. Disconnect the negative terminal on the battery that is located at the passenger firewall side. 2. Remove both front
More informationCOBB 3-Port Electronic Boost Control Solenoid
COBB 3-Port Electronic Boost Control Solenoid Mitsubishi Evolution X / Ralliart Congratulations on your purchase of the COBB Tuning 3-Port Electronic Boost Control Solenoid. The following instructions
More informationOwner smanual. Banks Techni-Cooler System Dodge 6.7L Cummins (24-valve) ISB Pickup Trucks (2500/3500) USE WITH SYSTEM P/N 25987
Owner smanual with Installation Instructions Banks Techni-Cooler System 2013-16 Dodge 6.7L Cummins (24-valve) ISB Pickup Trucks (2500/3500) USE WITH SYSTEM P/N 25987 Gale Banks Engineering 546 Duggan Avenue
More informationCOBB Tuning Catback Exhaust System MAZDASPEED3
572101 COBB Tuning Catback Exhaust System 2010+ MAZDASPEED3 Congratulations on your purchase of the COBB Tuning SS Catback Exhaust System for your 2010+ MAZDASPEED3. The following instructions will assist
More informationOIL COOLER KIT CHEVY CAMARO 2.0T PARTS LIST AND INSTALLATION GUIDE INSTALL DIFFICULTY DISCLAIMER CAUTION TOOLS NEEDED NOTE INSTALL PROCEDURE
PARTS LIST AND PARTS INCLUDED 3PC APPLICATION-SPECIFIC MOUNTING BRACKETS 1PC HORN RELOCATION MOUNTING BRACKET 1PC 25-ROW OIL COOLER (SLEEK SILVER OR STEALTH BLACK) 1PC 4'4" STAINLESS STEEL BRAIDED HOSE
More informationPerformance Inlet Manifold
Performance Inlet Manifold Tools needed (some tools not required on some models): 13mm Combination Wrench Flat Blade Screwdriver T30 Torx Driver T25 Torx Driver 10mm Combination Wrench and/or Socket with
More informationThe M7 Direct Flow Intercooler (DFIC) Installation Guide
The M7 Direct Flow Intercooler (DFIC) Installation Guide This information is meant only as a guide. The author of this information,, or any M7 Tuning employees assumes no liabilities for any outcomes resulting
More information2015+ SUBARU STI FRONT-MOUNT INTERCOOLER PARTS LIST AND INSTALLATION GUIDE INSTALL DIFFICULTY DISCLAIMER CAUTION INSTALL PROCEDURE TOOLS NEEDED
PARTS LIST AND PARTS INCLUDED 1PC ALUMINUM INTAKE PIPE 1PC BAR-AND-PLATE INTERCOOLER 1PC STEEL CRASH BAR W/ MOUNTING HARDWARE 2PC HOT-SIDE INTERCOOLER PIPES 2PC COLD-SIDE INTERCOOLER PIPES 1PC BPV FLANGE
More informationDifficulty Level: 3-4. This is very intensive for an intercooler installation. Experienced mechanical skills recommended. Wrenches Sockets Specialty
Nissan GT-R FMIC The goal of AMS is to provide the highest quality, best performing products available. By utilizing research and development, and rigorous testing programs AMS will never compromise the
More informationZZPerformance.com ZZP 3 Redline Cold Air Intake GEN 2
Tools you will need: Flat Blade Screwdriver Phillips Screwdriver 10mm End Wrench Ratchet Extension 5.5mm Socket 7mm Socket 10mm Socket 13mm Deep Socket ZZPerformance.com ZZP 3 Redline Cold Air Intake GEN
More informationINTERCOOLER PIPE KIT CHEVY CAMARO 2.0T PARTS LIST AND INSTALLATION GUIDE PARTS INCLUDED CAUTION INSTALL PROCEDURE TOOLS NEEDED
PARTS LIST AND PARTS INCLUDED 2PC ALUMINUM PIPES W/ CNC-MACHINED QUICK-DISCONNECTS 1PC ALUMINUM PIPE W/ CNC-MACHINED 2-BOLT FLANGE 2PC QUICK-DISCONNECT SPRING CLIPS 1PC 2.75" 90 SILICONE COUPLER 1PC 2.25"
More informationBRZ/FR-S 3.00 Cold Air Intake
BRZ/FR-S 3.00 Cold Air Intake Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of aftermarket performance
More informationZ1 Motorsports 300zx 2.5 Upgraded piping & BA SMIC Install Guide
Z1 Motorsports 300zx 2.5 Upgraded piping & BA SMIC Install Guide Congratulations on your new upgraded piping and intercooler kit, this kit has proven to provide the lowest intake air temps to date on our
More informationCOBB SF SHORT RAM INTAKE SYSTEM MazdaSpeed3
COBB SF SHORT RAM INTAKE SYSTEM MazdaSpeed3 Congratulations on your purchase of the COBB Tuning SF Intake System. The following instructions should assist you through your installation process. Please
More informationTools Required. Metric Wrench Set Screwdriver Set Metric Socket Set Pliers Heavy duty hydraulic Jack and Car Stands Box knife or similar Hacksaw WD40
Subaru 2004+ Legacy GT & Outback XT For JDM 2.0 twinscroll turbo and USDM 2.5 turbo models Front Mount Intercooler Fitting Instructions PN# LEG-1348-000 You are now the proud owner of a highly tested and
More information2016+ NISSAN TITAN XD
PARTS LIST AND PARTS INCLUDED 1PC MISHIMOTO INTERCOOLER 2PC SILICONE BOOTS WITH DURACORE TECHNOLOGY 4PC CONSTANT-TENSION T-BOLT CLAMPS 2PC ALUMINUM SPACERS MOUNTING HARDWARE CAUTION Never work on the cooling
More informationIE Audi B9 S4, S5, A4, A5, Allroad FDS Intercooler Install Guide IETPCK1
IE Audi B9 S4, S5, A4, A5, Allroad FDS Intercooler Install Guide IETPCK1 Thank you for purchasing the best performing intercooler on the market! This instruction guide is used for installation of IE s
More informationAlways wear safety glasses when working on your vehicle.
90-93 MAZDA MIATA SUPERCHARGER KIT The KraftWerks 90-93 Mazda Miata Supercharger Kit was designed for easy installation. Competent mechanics with the appropriate tools will find the process to be relatively
More informationTurboback Exhaust
501301 Turboback Exhaust 2014+ Ford Fiesta ST 501200 High Flow Catted Downpipe Page 2 501100 Catback Exhaust System Page 10 501200 High Flow Catted Downpipe 2014+ Ford Fiesta ST Congratulations on your
More informationINSTALLATION INSTRUCTIONS
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-818C (GUN METAL GRAY FINISH) 2017 Nissan Sentra SR Turbo 1.6T 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-2157DK
More informationCOBB Tuning Ford Carbon Fiber Air Scoop Focus ST COBB Ford Carbon Fiber Air Scoop Focus ST
791450 - COBB Tuning Ford Carbon Fiber Air Scoop Focus ST 2013-2017 791450 COBB Ford Carbon Fiber Air Scoop 2013-2017 Focus ST Congratulations on your purchase of the COBB Tuning Carbon Fiber Air Scoop!
More informationInstant Chat off the main page of Or simply call our tech team at
FRONT MOUNT INTERCOOLER 2015+ WRX 2017-07-07 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of
More informationCORKSPORT Short Ram Intake
I N S T A L L A T I O N I N S T R U C T I O N S CORKSPORT Short Ram Intake 2018+ Mazda 6 2.5T & 2016+ CX-9 PART #: ATK-6-117-xxxxx Need Help With Your Installation? Call (360) 260-CORK PAGE 1 CORKSPORT
More informationINSTALLATION INSTRUCTIONS PART NUMBER:
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER: 21-450B (Blue Finish) 21-450C (Gun Metal Grey Finish) 21-450P (Vacuum Metalized Chrome-VMC) 21-450R (Red Finish)
More informationCOLD AIR INTAKE SYSTEM. Installation Instructions for: Part Number Mitsubishi Lancer Ralliart Manual Transmission Only
COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-436 2004-2005 Mitsubishi Lancer Ralliart Manual Transmission Only ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne,
More informationINSTALLATION INSTRUCTIONS PART NUMBER AEM C (GUN METAL GRAY FINISH)
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER AEM-21-805C (GUN METAL GRAY FINISH) 2016.5-17 CHEVROLET CRUZE 1.4T ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-2038DK
More informationIAG Street Series Air / Oil Separator (AOS) For WRX
P IAG Street Series Air / Oil Separator (AOS) For 2015-16 WRX Part# IAG-ENG-7152 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw driver,
More informationInstallation Instructions Camaro ZL1 ( Z) ( ZB)
Installation Instructions Camaro ZL1 (501-1099-10-Z) (501-1099-10-ZB) Parts List 1 Insulated Air Box \ Lid 1 Thermal Coated Intake Tube / MAF Housing with (2) M4 x.7 thread 8mm long Stainless Screws; 1
More informationSHORT RAM SYSTEM. Installation Instructions for: Part Number Honda Civic Si
SHORT RAM SYSTEM Installation Instructions for: Part Number 22-516 2006 Honda Civic Si ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310) 484-0152
More informationSubaru WRX Performance Charge-Pipe System, 2015+
PARTS LIST AND PARTS LIST 1PC BAR-AND-PLATE INTERCOOLER 1PC INTERCOOLER MOUNTING BRACKET 1PC CHARGE-PIPE ASSEMBLY 1PC AIR DIVERTER WITH ATTACHED RUBBER GASKETS 1PC CHARGE-PIPE-TO-INTERCOOLER HOSE INSTALLATION
More informationDURAMAX LMM EGR DELETE
007.5-010 DURAMAX LMM EGR DELETE Duramax LMM EGR Delete B K I J F D G H A C PACKING LIST: E Part # A B C D E F G H I J K QTY. 1 1 1 1 Description Billet Intake Block Off Plate with O-ring Exhaust Block
More information5B HIGH FLOW CATTED DOWNPIPES N54 135i/335i
5B1202 - HIGH FLOW CATTED DOWNPIPES N54 135i/335i Installation Instructions Front Downpipe Rear Downpipe Congratulations on your purchase of the COBB High Flow Catted Downpipes for your N54 BMW 135i/335i!
More informationFocus RS Catback
593100 - Focus RS Catback 593100 Focus RS Catback Ford Focus RS 2016-18 Congratulations on your purchase of the COBB Tuning Focus RS Catback Exhaust! The following instructions will assist you through
More informationProcharger Stage II Intercooled Supercharger System (11-14 GT)
Procharger Stage II Intercooled Supercharger System (11-14 GT) Installation Time: Approximately one day. Installed on 2012 Mustang GT 5.0/Manual Required Tools 3/8 Socket Set (Standard and Metric) 1/2
More informationInstallation Manual. Model Chassis Code Engine Code Year
INTERCOOLER KIT NISSAN GT-R R35 (VR38 38DETT) SPEC-R HG TYPE29 Full KIT Installation Manual Please read the Installation Manual before installing. Keep this manual for future reference. Model Chassis Code
More informationInstallation Manual. Model Chassis Code Engine Code Year
INTERCOOLER KIT NISSAN GT-R R35 (VR38 38DETT) SPEC-R HG TYPE29 Full KIT Installation Manual Please read the Installation Manual before installing. Keep this manual for future reference. Model Chassis Code
More informationSlingshot Rotrex Supercharger Kit
Slingshot Rotrex Supercharger Kit This supercharger kit improves on the Slingshot by forcing more dense air into the engine and creating more power. Installation time of the supercharger depends on you
More informationBanks High-Flow Boost Tubes. Step-by-step installation video: Bankspower.com/v/install-lml-boost-tubes
with Installation Instructions Owner smanual Banks High-Flow Boost Tubes Stock Fitment 2011-2016 Chevy/GMC Turbo-Diesel Pickup Trucks THIS MANUAL IS FOR USE WITH PART NUMBER 25993 Gale Banks Engineering
More informationINSTALLATION INSTRUCTIONS PART NUMBER:21-729
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER:21-729 2010-2013 MAZDA MX-5 MIATA 2.0L I-4 PARTS LIST Description Qty. Part Number A Tube, Lower Intake, 2006-13
More informationIAG Competition Series Air / Oil Separator (AOS) For WRX
P IAG Competition Series Air / Oil Separator (AOS) For 2015-16 WRX Part# IAG-ENG-7252 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flat head screw
More informationJBR MAZDASPEED
Page1 james Barone Racing Aftermarket Parts and Accessories JBR 2007 2009 MAZDASPEED 3 Front Mount Intercooler Piping Kit Installation Instructions for TR8 Intercooler Tooling: o Jack, Jack Stands, Ramps
More informationCOLD AIR SYSTEM. Installation Instructions for: Part Number Nissan 350Z
COLD AIR SYSTEM Installation Instructions for: Part Number 21-547 2003-2006 Nissan 350Z ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)
More informationIAG Street Series Air / Oil Separator (AOS) For 2017 WRX
P IAG Street Series Air / Oil Separator (AOS) For 2017 WRX Part# IAG-ENG-7152 Tools Required: Ratchet, torque wrench, extensions, needle nose pliers, hose cutter, snips/scissors, flathead screwdriver,
More information2016+ Mazda Miata Front & Rear Sway Bar Installation Instructions
Page1 James Barone Racing Aftermarket Parts and Accessories 2016+ Mazda Miata Front & Rear Sway Bar Installation Instructions Tools Required: Jack Lift or ramps Ratchet wrench Torque Wrench 6 and 12 Extension
More informationPlease take time to read and understand these installation instructions.
Cat Back Exhaust System 2013+ SRT/ GTS Viper Please take time to read and understand these installation instructions. CORSA recommends that the installation of this system be performed by a qualified service
More informationInstallation Manual Volvo C30 T5 Front Mount Intercooler System
Installation Manual Volvo C30 T5 Front Mount System Volvo C30 T5 System / Installation Manual i C Contents Important Information i Parts List i Required Tools and Materials 1 1.0 - Vehicle Preparation
More information9F1760/9F1761 COBB Sport Springs Ford Focus ST
9F1760/9F1761 COBB Sport Springs 2013+ Ford Focus ST Installation Instructions Congratulations on your purchase of the COBB Sport Springs for your 2013+ Ford Focus ST. These instructions should only be
More informationL DURAMAX LBZ EGR DELETE GDP TUNING
2006-2007.5 6.6L DURAMAX LBZ EGR DELETE GDP TUNING ! WARNING REGARDING EMISSIONS LAWS Not legal for sale or use on pollution-controlled motor vehicles anywhere in the be used on vehicles that are operated
More informationIncluded: 2. Intake Block Off Plates 1. Exhaust Block Off Plate 1. Coolant Hose - Reroutes the EGR Cooler Coolant 12. Pieces of mounting hardware -
Included: 2. Intake Block Off Plates 1. Exhaust Block Off Plate 1. Coolant Hose - Reroutes the EGR Cooler Coolant 12. Pieces of mounting hardware - Nuts, Bolts, & Washers 2. Hose Clamps 1. Support Bracket
More informationCOBB SPORT SPRINGS
913760 - COBB SPORT SPRINGS 2004-2007 Subaru WRX/STi Congratulations on your purchase of the COBB Sport Springs for your 2004-2007 Subaru WRX/STi. The following instructions will assist you through your
More informationMazda 3 & Mazdaspeed 3 Oil Cooler Installation Instructions
Page1 2007-2009 Mazda 3 & Mazdaspeed 3 Oil Cooler Installation Instructions Tooling: Jack and jack stands or a lift Socket wrench and torque wrench 10mm and 14mm sockets 3/16 Allen wrench 10mm wrench Pliers
More informationSHORT RAM SYSTEM. Installation Instructions for: Part Number Nissan 240SX
SHORT RAM SYSTEM Installation Instructions for: Part Number 22-441 1995-1998 Nissan 240SX ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)
More informationPart number SP Mitsubishi Lancer 4 cyl. 2.0L non-turbo. 1- Three piece cold air intake
Part number SP1835 08-09 Mitsubishi Lancer 4 cyl. 2.0L non-turbo 1- Three piece cold air intake 1- Formed silicone hose (#3158) 1-2 1/2 Injen filter (#1012) 1-2 3/4 straight hose (#3043) 4- Power-Bands.312.040
More informationINSTALLATION INSTRUCTIONS
N-MT13-1 & N-MT13-2 COLD AIR INTAKE KIT INSTALLATION INSTRUCTIONS MUSTANG GT 2015-up PARTS INCLUDED Part Number Descrip on Qty 9-SA-INTAKE-100 Intake Assembly 1 9-SA-HEATSHIELD-100 Heatshield Assembly
More informationCorkSport Mazdaspeed Protégé Intercooler Hoses Mazdaspeed Protégé
CorkSport Mazdaspeed Protégé Intercooler Hoses 2002-2003.5 Mazdaspeed Protégé Thank you for purchasing the CorkSport Mazdaspeed Protégé Intercooler Hose Kit. This kit has been designed and tested to be
More informationINSTALLATION INSTRUCTIONS Unitronic Intercooler Upgrade Kit for 2.0 TFSI (EA113) UH007-ICA
Unitronic recommends that you read through the entire installation instructions prior to beginning the installation to familiarize yourself with the included components, tools required, and procedures
More informationLightweight Tubular Sway Bar Kit Subaru WRX / STi / 09+ FXT
915250 Lightweight Tubular Sway Bar Kit 2008+ Subaru WRX / STi / 09+ FXT Installation Instructions Congratulations on your purchase of the COBB Lightweight Tubular Sway Bar Kit for your Subaru WRX, STi
More informationPerformance Air Intake, 2015+
PARTS LIST AND PARTS LIST 1PC ALUMINUM INTAKE PIPE 1PC HIGH-FLOW, OILED AIR FILTER 1PC SILICONE INDUCTION HOSE 1PC AIRBOX 1PC 1/16 RUBBER STRIPPING, 9 LENGTH 1PC 1/16 RUBBER STRIPPING, 8.5 LENGTH 1PC WORM-GEAR
More informationInstallation Instructions
Installation Instructions Transverse K04 Tools Required Jack and jack stands Drain pan for coolant and oil 3" and 6" extensions Channel locks 7mm, 8mm, 10mm, 11mm, 12mm, 13mm, and 16mm sockets Oxygen sensor
More informationCOLD AIR INTAKE SYSTEM. Installation Instructions for: Part Number MazdaSpeed Protégé 2.0L Turbo
COLD AIR INTAKE SYSTEM Installation Instructions for: Part Number 21-486 2003-2003.5 MazdaSpeed Protégé 2.0L Turbo ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone:
More informationEquipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER C (GUN METAL GRAY FINISH) NISSAN SENTRA 1.
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-799C (GUN METAL GRAY FINISH) 2014-16 NISSAN SENTRA 1.8L 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-2157D AIR
More informationC&L Cold Air Intake w/ 80MM MAF (01 Bullitt)
C&L Cold Air Intake w/ 80MM MAF (01 Bullitt) Install time: Approx. 30 min. Tools Required: 10mm Socket 8mm Socket 3/8in ratchet or 1/4in ratchet Flat head screw driver 1/4in bit driver for supplied T20
More informationIncludes: 1. Upgraded Tube Type EGR Cooler 2. Silicone Hoses
Includes: 1. Upgraded Tube Type EGR Cooler 2. Silicone Hoses CAUTION: Never work on a hot vehicle. The hot exhaust system or hot engine can cause serious injury in the form of burns. If the vehicle has
More informationCOBB Fuel Pressure Regulator Kit
315100 COBB Fuel Pressure Regulator Kit 2008+ Subaru STI Congratulations on your purchase of the COBB Tuning Fuel Pressure Regulator Kit for your 2008+ Subaru STI. The following instructions will assist
More informationYou can purchase this part at: COLD AIR SYSTEM
COLD AIR SYSTEM Installation Instructions for: Part Number 21-450 2000-2003 Ford Focus 2.0L Zetec ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax:
More informationMustang Headlight w/ CCFL Halo (05-09) - Installation Instructions
Mustang Headlight w/ CCFL Halo (05-09) - Installation Instructions The below installation instructions work for the following products: Chrome Mustang Headlight w/ CCFL Halo (05-09) Smoked Mustang Headlight
More informationCOLD AIR SYSTEM. Installation Instructions for: Part Number Volkswagen Golf/GTI 1.8L Turbo Volkswagen Jetta 1.
COLD AIR SYSTEM Installation Instructions for: Part Number 21-493 1999.5-2004 Volkswagen Golf/GTI 1.8L Turbo 1999.5-2004 Volkswagen Jetta 1.8L Turbo ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street,
More informationSHORT RAM AIR INTAKE SYSTEM. Installation Instructions for: Part Number Nissan 350Z
SHORT RAM AIR INTAKE SYSTEM Installation Instructions for: Part Number 22-547 2003-2006 Nissan 350Z ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322
More informationTDR Cold Air Intake for the NC
TDR Cold Air Intake for the NC Year: Models: TDR-CAI-NC Thank you for purchasing the Track Dog Racing Cold Air Intake for the NC. The Cold Air Intake is designed with and very efficient K&N Filter and
More informationVolkswagen MKIV 1.8T/2.0L/VR6 XAS Cold Air Intake System Installation
Volkswagen MKIV 1.8T/2.0L/VR6 XAS Cold Air Intake System Installation Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety
More informationSubaru 5-Speed Double Adjustable Short Throw Shifter
Subaru 5-Speed Double Adjustable Short Throw Shifter 1999+ Subaru Impreza 5-Speed 2004-2005 Subaru Forester XT 5-Speed Congratulations on your purchase of the COBB Tuning Double Adjustable Short Throw
More informationPart number SP1305. Maintaining your Cold air intake system: Tools required:
Part number SP1305 2000-03 Honda S2000 4 cyl. 2.0L 2004-06 Honda S2000 4 cyl. 2.2L 1-2 piece cold air intake 1-3 Injen filter (#1014) 1-2 3/4 x 3 silicone step hose (#3040) 1-3 straight hose (#3044) 1-
More informationPart number SP Hyundai genesis 2.0L turbo 4 cyl.
Part number SP1386 2010 Hyundai genesis 2.0L turbo 4 cyl. 1-1 piece Cold air intake system 1-3 1/2 Injen/AMSOIL Ea nano-fiber Performance Dry Filter (#1021) 1-1 1/8 x 3 long str. hose (#3109) 1-7 -10mm
More information2015+ WRX Charge Pipe
2015+ WRX Charge Pipe 2017-04-20 Thank you for purchasing this PERRIN product for your car! Installation of this product should only be performed by persons experienced with installation of aftermarket
More information3/8 Universal Joint Phillips Head Screwdriver
Magnetic retrieval tool Pliers 1/4 Ratchet Drive T-35 Torx Socket 3/8 Ratchet Drive 5mm Allen Head Socket Torque Wrench 7-3/8 Drive Extension Flat Head Screwdriver 10mm Socket 8mm Socket 3/8 Universal
More informationINSTALLATION INSTRUCTIONS ELEVATION FRONT BUMPER DODGE RAM
INSTALLATION INSTRUCTIONS PARTS LIST: 1 Elevation Bumper Assembly 24 12mm x 37mm OD x 3mm Flat Washers 2 Frame Mounting Brackets 12 12mm Nylon Lock Nuts 8 12-1.75mm x 50mm Hex Bolts 2 License Plate Mounting
More informationADVANCED ENGINE MANAGEMENT INC.
COLD AIR SYSTEM Installation Instructions for: Part Number 21-474 2002-2005 Subaru Impreza WRX 2004-2005 Subaru Impreza WRX STi 2004-2005 Subaru Forester XT 2004-2005 Saab 92X ADVANCED ENGINE MANAGEMENT
More informationPARTS LIST INSTALLATION INSTRUCTIONS PARTS LIST AND INSTALLATION GUIDE INSTALL TIME: 2 HOURS INSTALL DIFFICULTY: 3/5
PARTS LIST AND PARTS LIST 1PC MISHIMOTO INTERCOOLER 1PC M6 X 1.0 X 20MM FLANGE BOLT 1PC M4 X 0.7 X 12MM BUTTON-HEAD BOLT 1PC M4 LOCK WASHER 1PC MAP SENSOR O-RING 2. Remove the eight pop clips that hold
More informationFRONT MOUNT INTERCOOLER GOLF / JETTA IV 1.8T PART # & P INSTALATION INSTRUCTIONS
FRONT MOUNT INTERCOOLER GOLF / JETTA IV 1.8T PART # 48.10.90 & 48.10.90P INSTALATION INSTRUCTIONS PART LIST: 1 INTERCOOLER CORE 1 U-BENT TUBE 1 L-SHAPED TUBE 1 INTERCOOLER INLET TUBE 4 M6 NYLOC NUT 3 M6
More informationCOBB SPORT SPRINGS
915760 - COBB SPORT SPRINGS 2008-2013 Subaru WRX/STi Congratulations on your purchase of the COBB Sport Springs for your 2008-2013 Subaru WRX/STi. The following instructions will assist you through your
More informationIncludes: 1. Silicone Hose 2. EGR Block Off Plates 1. Exhaust Block Off Plate 2. Hose Clamps 1. Spacer/Washer 8. Bolts 2. Nuts
Includes: 1. Silicone Hose 2. EGR Block Off Plates 1. Exhaust Block Off Plate 2. Hose Clamps 1. Spacer/Washer 8. Bolts 2. Nuts WARNING: This product is not legal for sale or use on pollution controlled
More informationCOLD AIR INTAKE INSTALLATION INSTRUCTIONS PART NUMBER D A. APPLICATION: E36/7 M-Roadster or M-Coupe 3.
COLD AIR INTAKE INSTALLATION INSTRUCTIONS PART NUMBER D760-0323A APPLICATION: 1998-00 E36/7 M-Roadster or M-Coupe 3.2 Liter PARTS LIST Air Filter Assembly 3 1/2" Tube Intake Shield Silicone Hose Airflow
More informationSCION xb PERFORMANCE AIR INTAKE Section I Installation Preparation 2.4L I-4
Section I Installation Preparation 2.4L I-4 Part Number(s): PTR03-52110 Kit Contents Item # Quantity Description Reqd. 1 1 TRD Inlet Tube 2 1 TRD Upper Air Box with HC Trap 3 1 Hump Hose Coupler 4 1 Hump
More informationRemoval of bumper & intercooler:
R56 Front Mount Intercooler 090107 Thank you for purchasing the ALTA Performance R56 Front Mount Intercooler kit. Persons experienced in the proper operation of MINI engines should only perform this installation.
More informationHYUNDAI VELOSTER SHORT RAM 1.6T INTAKE INSTALLATION INSTRUCTIONS
Installation: HYUNDAI VELOSTER SHORT RAM 1.6T INTAKE INSTALLATION INSTRUCTIONS Tools needed: 1/4 or 3/8 drive ratchet 12 extension (shorter ones work, but will be difficult to reach some bolts) 10mm socket
More informationPerformance Oil Cooler Kit for (C6) Chevrolet Corvette
Performance Oil Cooler Kit for 2005-2013 (C6) Chevrolet Corvette Part No. EC6-600 Made in USA Important: Read these instructions in their entirety prior to installation. Copyright 2008-2018 Improved Racing
More informationINSTALLATION INSTRUCTIONS
Equipped with AEM Dryflow Filter No Oil Required! INSTALLATION INSTRUCTIONS PART NUMBER 21-822C (GUN METAL GRAY FINISH) 2008-12 Honda Accord 2.4L 1 ITEM NO. PART NUMBER DESCRIPTION QTY. 1 21-203DOS Air
More informationCOLD AIR SYSTEM. Installation Instructions for: Part Number Infiniti G35
COLD AIR SYSTEM Installation Instructions for: Part Number 21-548 2003-2005 Infiniti G35 ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone: (310) 484-2322 Fax: (310)
More informationSHORT RAM SYSTEM. Installation Instructions for: Part Number Toyota Corolla & 2003 Toyota Matrix XR
SHORT RAM SYSTEM Installation Instructions for: Part Number 22-469 2003-2004 Toyota Corolla & 2003 Toyota Matrix XR ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone:
More informationCOLD AIR SYSTEM. Installation Instructions for: Part Number Toyota Corolla Toyota Matrix XR
COLD AIR SYSTEM Installation Instructions for: Part Number 21-469 2003-2004 Toyota Corolla 2002-2004 Toyota Matrix XR ADVANCED ENGINE MANAGEMENT INC. 2205 126 TH Street, Unit A Hawthorne, CA. 90250 Phone:
More information