HI PerFORMANCE 1/8 OFF-ROAD NITRO BUGGY. Instruction manual OFNA 7 VANDERBILT, IRVINE, CA PH. (949)

HI PerFORMANCE 1/8 OFF-ROAD NITRO BUGGY. Instruction manual OFNA 7 VANDERBILT, IRVINE, CA 92618 PH. (949) 586-2910

THINGS NEEDED RTR KITS - REQUIRED FOR OPERATION You will need to buy a few items to start the engine and run the car. Use 20% nitro CAR fuel. Do not use airplane or heli fuels, they will over heat engine. Buy LONG glow plugs, like OFNA/PICCO Plug (#51007 or 51008). Use plugs WITHOUT idle bar. Do NOT use plugs, like the MC-59 or OS-8 In your box you will find.. #10163 - Bottle, spout top #10219 - Red D size glow heater AA Batteries ( 12 pcs ) You need to get batteries for the radio transmitter and the car receiver packs. Radio TX needs (8) eight AA batteries. Car needs (4) four AA Alkaline., Alkaline type batteries will work, but braking will be reduced and 30 minute life. The best for car, is to use a 5 cell hump receiver pack for increased voltage and longer life.. #10202 1700 Ni-Mh Hump Pack, Recommended Option: You may want to upgrade the car battery pack to a Ni-Cad or Ni-Mh 5 cell type(600ae). This will give more run time. OFNA #10202 1700Ni-Mh Hump Pack and Ni-Mh Battery Charger #10214 10214 Over-nite Charger TOOLS NOT INCLUDED IN KIT, BUT NEEDED TO MAINTAIN YOUR CAR. Cutter Instant Cement Phillips Type Screw Drivers ( L ) Curved Scissors #91009 $5.95 Grease Phillips Type Screw Drivers ( S ) Cross Wrench #17109 $3.95 Needle Nose Pliers Knife Glow Plug & 17MM Cross Wrench #10801 $6.95

MUST READ THIS BEFORE RUNNING Running a nitro kit is fun and easy, but to make this a safe and good experience you must observe a few rules. This kit is extremely fast, easily over 40MPH, and can seriously injure someone if you are not careful. Where to run car? Any running area you choose must be dry. Do not run car near any water or wet dirt. Do not run on public streets. It is very easy to have the car run over or damaged by hitting the curb. Do not operate car in tight confined places. The car is very fast and will easily hit something. Do not run near people or animals. The car is very fast and will too easily hit someone. Due to noise, you will want to consider the surrounding area when operating the car. Do not operate the car at night. You will not be able to drive it without hitting something. Do not operate the car indoors. Engine exhaust is not healthy. Glow Fuel Glow fuel is poisonous! Glow fuel is flammable! Do not leave in fuel bottle with lid off at any time. Do not use any fuel other than glow fuel in this engine. First Time Starting the Engine Caution! When starting engine make sure the following is observed. Set engine Master needle to 3 turns (rich setting) Do not do this alone, get an experienced friend to help at first. Fill fuel tank, try not to spill fuel. Do not spill fuel on receiver Hold car off the ground, so it will not runaway when first starts Turn on Radio and check the linkage before starting engine. Turn on car receiver battery switch. Always have an air filter on the carburetor to keep dirt out of engine. Engine Break-in See Engine Page. Emergency Stopping Engine When Running Remove air filter and cover carb. intake. Squeeze fuel line and hold until engine stops. With a rag, cover exhaust outlet. Storing Car After Running Remove fuel from tank and fuel lines Turn off radio in car Put a few drops of after run in engine to keep it from rusting. Clean oil and dirt from chassis with a degreaser like Simple Green. Precautions This kit is not a toy. Always run car with a second person as a spotter and pitman. Hot Parts - The pipe, manifold, engine and head are very hot and will cause burns. Rotating Parts - Keep hands away from the drive train, wheels, and engine when engine is running. Radio - Check batteries life before running the car. If radio does not have full control of the car with steering and/or throttle/brake do not run until corrected. Failure to correct this will result in possible injury and damage to the car or property. Glow fuel - Do not leave the glow fuel unattended with the lid off. Fuel contains Methanol and Nitro Methane both are flammable and poisonous. Store fuel in cool ventilated location. Refer the glow fuel label for additional precautions. Car Fuel tank - Never store fuel in car tank, it will ruin the engine if left in tank. Always turn off the car BEFORE turning off radio. DAMAGE DUE CAR RUN AWAY IS NOT A WARRANTY ISSUE. IF YOU DO NOT BREAK-IN ENGINE CORRECTLY, MAINLY AT LOW RPM, YOU WILL BREAK THE CONNECTING ROD! FAILURE TO NOT READ AND FOLLOW BREAK-IN ENGINE INSTRUCTIONS WILL VOID WARRANTY! CHECK RADIO SETTING, LINKAGE BEFORE STARTING.

OPTION PART THINGS REQUIRED FOR OPERATION OPTION THINGS NEED BESIDES THE KIT 3.5 cc (21 Class) ENGINE REAR EXHAUST OFNA/Picco P7-EVO3 #51216 Glow Plug Heat with Battery & Charger # 10227...$$19.95 (please note OFNA Glow Heats available) Bottle s with spout # 10160 - large 500cc # 10161 - large 500 ccauto Stop # 10162 - small 250cc # 10164 - CNC spout 500CC # 10167 - CNC spout 800CC Off-Road Starter Box, 12V motor # 10250-1/8 scale Starter Box # 10253-1/8 scale Starter Box w/ Panel Off-Road Starter Box, two 550 motors # 10248-1/8 scale Starter Box # 10249-1/8 scale Starter Box,RTR Optional Parts # 92571 - Power Panel Glow Heater # 92572 - Cable for Glow Plug 12V Battery for Starter Box (must have) AA Batteries ( 12 pcs ) for radio RADIO CONTROL UNIT Note: Carefully read the instruction manual of your 2 channel radio controller before using. SUITABLE SERVO SIZE 36mm-41mm 15mm - 21mm 29mm - 42mm Radio must be set at neutral position before installing in the kit. SEQUENCE TO SET NEUTRAL Install AA batteries in Radio. Extend the antenna.(transmitter) Install batteries into Car receiver. After installing the battery, connect the battery box. Extend the antenna. (Receiver) Set the trim-lever at center. Turn on the switch. (Transmitter) Turn on the switch. (Receiver) Make sure the servos are in command. When the operation stick is in neutral, servo horns must be in neutral as well. *Adjustment can be made by reinstalling the servo horn. 11 Turn off the switch. (Receiver) 12 Turn off the switch. (Transmitter) 13 Retract the antenna. (Transmitter) More Optional Parts... #10201 1700 NimH Battery Hump Pack.. $34.95 # 10214 NiMh Battery Pack Charger.. $7.95 # 51007 or 08 OFNA/Picoo Glow Plug.. $13.95 TOOLS NOT INCLUDED IN KIT Cutter Instant Cement Phillips Type Screw Drivers ( L ) Curved Scissors Masking Tape INCLUDED WITH KIT 5mm Hex Wrench Phillips Type Screw Drivers ( S ) Brush Cross Wrench #17109 $3.95 Hex Wrench 2.5mm Hex Wrench Needle Nose Pliers Paints 1.5mm Hex Wrench Knife Glow Plug & 17MM Cross Wrench #10801 $6.95 Grease 7mm and 5.5mm Hex Wrench

PLASTIC PARTS FOR USE 40047 RECEIVER BOX 40046 STONE GUARD 40020 REAR LOWER ARM 36081 REAR UPRIGHT 36901 FRONT KNUCKLEARM ARM 40003 DIFF. CASE 40017 GEAR BOX 40202 FRONT LOWER ARM

PLASTIC PARTS FOR USE 40040 CENTER DIFF. MOUNT 40027 WING STAY 40094 FRONT UPPER ARM 40018 / 40029 CHASSIS BRACE 40031 SERVO SAVER 16015 WING SYMBOL USED THROUGHOUT THE INSTRUCTION MANUAL BAG Parts Bag Used Degrease With Motor Spray Do Not Over Tighten Do Not Over Tighten Tighten Tighten Ensure Free Movement Ensure Free Movement Contact Adhesive Contact Adhesive Scre w Cement Apply Screw Cement Oil Apply Oil Apply Grease Apply Grease 1:1 True-To-Scale 1:1 ì o ¹Ï Rotate Direction Clockwise Rotation Rotate Direction Anti-clockwise Rotation

1 ASSEMBLY OF THE FRONT AND REAR DIFF. Builds two differentials for front and rear. 94034 4x4mm Set Screw 4x4 mm 40010 40010 40009 P6 O-Ring 40010 2.5x13.8mm Pin 40006 Oil 40513 40009 49032 Oil 40003 40006 8x16mm Ball Bearing 40009 40513 2 ASSEMBLY OF THE FRONT AND REAR DIFF. Builds two differentials for front and rear. Step 1 30776 Step 2 40513 30773 Tighten Tight the diff screws in this order. 30776 4x10mm Washer...X8 1 3 94020...X8 Flat Head 40011 4 2 30773 4mm Cross Pin...X4 Diff. Oil *Put the Diff. Oil #3000 for front and the #1000 for rear *Fill the Diff. case to approx. 80% with the Diff. Oil 3 ASSEMBLY OF THE CENTER DIFF. 94034 4x4mm Set Screw 4x4mm 40010 40005 40010 40009 P6 O-Ring 40513 40010 2.5X13.8MM PIN Oil 40003 40513 40009 40001 Oil 8x16mm Ball Bearing 40009 40005 1

4 ASSEMBLY OF THE CENTER DIFF. 30776 4x10mm Washer 30773 40513 30776 Tighten Tight the diff screws in this order. 94020 Flat Head...4 1 3 40011 30773 4mm Cross Pin...X2 4 2 Diff. Oil Use 5000 weight diff. oil in the center. Fill the Diff. Case to approx. 80% with the Diff.Oil. 5 ASSEMBLY OF THE FRONT GEAR CASE Scre w Ce me nt 5x4mm Step 1 94036 5x4mm Set Screw 40024 94027 13x16x0.2mm Shim 4x16mm Flat Head Screw...X4 94011 4x16mm 4x16mm 40024 Apply Grease 49012 40017 Step 2 30080 4x45mm 40024 40017 8x16mm Ball Bearing 49048 40015 4x16mm 40015 94014 4x45mm 4x16mm 6 ASSEMBLY OF THE FRONT SHOCK STAY 94042 4mm Nylon Nut 49047 41009 4mm Nylon Nut 94004 41010 41009 4mm Nylon Nut 94010 4x12mm 94011 4x16mm 41010 4x16mm 4x12mm 41009 3x28mm Cap Screw 2

7 ASSEMBLY OF THE FRONT LOWER ARMS Assembly for both right and left side. 90021 E-Ring 36870 4x10mm Set Screw 4x10mm 40202 40524 8 ASSEMBLY OF THE FRONT UPPER ARMS Assembly for both right and left side. 2.5mm 90020 2.5mm E-Ring 2.5mm 40094 40094 36170 40094 9 ASSEMBLY OF THE KNUCKLE ARMS Assembly for both right and left side. 94034 4x4mm Set Screw Step 1 * L for left handside. 36903 36905 L 36055 2.5x16.8mm Pin 36904 36901 Ensure Free Movement 34053 Step 2 8x16mm Ball Bearing Do Not Over Thigten 36904 36905 36903 30656 36903 14mm Steering Ball Screw Cement 36055 4x4mm 3

10 ASSEMBLY OF THE FRONT SUSPENSION ARMS Assembly for both right and left side. * Insert the drive shaft before assembling the knuckle arm. 11 ASSEMBLY OF THE FRONT STABILIZER Assembly for both right and left side. 94035 3x8mm Set Screw 30403 6mm Ball Makes two rods for left and right hand-side. 94005 3x16mm 30341 40029 3x8mm 40029 30403 3x16mm 12 ASSEMBLY OF THE FRONT STABILIZER 3x Screw Cement 94033 3x Set Screw Screw Cem ent 3x 8mm 94019 Flat Head 40019 3x 40018 3x Ensure Free Movement 4

13 ASSEMBLY OF THE SERVO SAVER 40035 40037 40031 Plastic Flange Bushing 40031 40037 40031 40031 49052 40031 40031 40033 40034 14 ASSEMBLY OF THE SERVO SAVER AND THE STEERING TIE-ROD 40027 cr w S e me t Ce n 94041 Nylon Nut 4x10mm 40031 Screw Cement 49051 94003 40038 40039 36700 94009 4x10mm 40031 36790 40038 3x18mm 40036 36700 94022 3x18mm Flat Head 40036 1:1 *Approx. 26mm 15 40018 ASSEMBLY OF THE SERVO SAVER ONTO THE FRONT GEAR BOX ½w½Ä²Õ»P«e¾ ½ü½c²Õ X 94041 Nylon Nut 94009 4x10mm 4x10mm 3x20mm 40039 94022 3x20mm Flat Head 3x20mm 40039 5

16 ASSEMBLY OF THE REAR GEAR CASE Screw Cement Step 1 5x4mm Step 2 4x12mm 94036 5x4mm Set Screw 94010 4x12mm 40017 30080 40027 4x12mm 8x16mm Ball Bearing 49012 49049 40024 13x16x0.2mm Shim 40024 40024 4x16mm 94003 4x45mm 40017 94011 4x16mm 94030 4x45mm Flat Head Screw...X2 4x45mm 40015 17 ASSEMBLY OF THE REAR SHOCK STAY Step 1 41009 Step 2 94003 40027 41009 41010 94004 90018 3x25mm Cap Screw 41010 49050 18 ASSEMBLY OF THE WING STAY 40027 3x20mm 94005 3x16mm 40027 94007 3x20mm 3x16mm 40027 40027 40027 3x20mm 40027 3x16mm 6

19 ASSEMBLY OF THE WING STAY 94041 Nylon Nut 4x20mm 94042 4mm Nylon Nut 4x16mm 94011 4x16mm 94012 4x20mm 4x16mm 4mm Nylon Nut 3x25mm 40018 94008 3x25mm 20 ASSEMBLY OF THE REAR LOWER ARMS Assembly for both right and left side. 90020 2.5mm E-Ring 36082 36081 40020 40020 94036 5x4mm Set Screw 40020 36055 2.5mm 36055 2.5x16.8mm Pin 30656 2.5mm 5x4mm 36170 21 ASSEMBLY OF THE REAR SUSPENSION ARMS Assembly for both right and left side. 90021 E-Ring 36870 4x10mm Set Screw 4x10mm Ensure Free Movement 40524 7

22 ASSEMBLY OF THE REAR SUSPENSION ARMS 94041 Nylon Nut Nylon Nut Assembly for both right and left side. Assembly of the rear upper arm. 40065 36861 36850 36850 7mm Ball 40065 36850 94006 3x18mm 94008 3x25mm 3x18mm Nylon Nut 1:1 *Approx. 1 36111 3x25mm *Insert the drive shaft before assembly the upper arms. 23 ASSEMBLY OF THE REAR STABILIZER Assembly for both right and left side. Makes two rods for left and right hand-side. 94035 3x8mm Set Screw 40029 30403 6mm Ball 30341 30403 3x8mm 40029 94005 3x16mm 3x16mm 24 ASSEMBLY OF THE REAR STABILIZER 3x Scre w Cement 94033 3x Set Screw Scre w Ce me nt 3x 94019 Flat Head Screw 40019 40018 3x Ensure Free Movement 8

25 ASSEMBLY OF THE CENTER DIFF. MOUNT Step 1 Step 2 Step 3 40040 40042 40512 40040 40512 40042 26 ASSEMBLY OF THE BRAKE DISK INTO CENTER DIFF. MOUNT Step 1 A B C 36661 Step 3 36660 Step 2 C * Place the brake disc between the brake disc pads. * Remove the double-side tape before assembly. A B 40040 Brake disc double-side tape 40044 36661 40045 27 ASSEMBLY OF THE CENTER DIFF. MOUNT *Approx. 8mm *8m ù Step 1 Approx. 4mm Step 2 49053 40031 3x 40040 94033 3x Set Screw 40040 3x 40040 Plastic Flange Bushing 30171 30213 30171 94004 9

28 31 ASSEMBL Y OF THE STONE GUARD Assembly for both right and left side. 40064 94003...x6 40046 40046 29 ASSEMBLY OF THE FRONT GEAR CASE ONTO CHASSIS 94039 4x10mm Flat Head 94026 4x12mm Flat Head 40013 94027 4x16mm Flat Head 4x10mm 4x12mm 4x16mm 30 ASSEMBLY OF THE CENTER DIFF. ONTO CHASSIS *Insert the drive shaft into the cap joint before assembly the center diff. onto chassis. 94046 2.6x10mm Tapping Screw 40028 94039 4x10mm Flat Head Screw 2.6x10mm 2.6x10mm 4x10mm 4x10mm 10

31 ASSEMBLY OF THE REAR GEAR CASE ONTO CHASSIS 94026 4x12mm Flat Head *Insert the drive shaft into the cap joint before assembly rear gear box onto chassis. 40028 94027 4x16mm Flat Head 4x16mm 4x12mm 32 ASSEMBLY OF THE RADIO TRAY Step 1 3x8mm Step 2 94040 3x8mm Washer...x8 3x8mm 94003...x6 3x8mm 3x8mm 94004...x8 49054 40047 40031 40031 40047 33 ASSEMBLY OF THE RADIO TRAY AND RECEIVER BOX 2x10mm Tapping Screw 30560 2x10mm * Use the screw provided with your switch. 40047 94003 2x25mm 40047 94004 10282 Receiver 2x25mm Screw Switch 40047 11

34 ASSEMBLY OF THE STEERING SERVO AND STEERING ROD 1:1 *Approx. 18.5mm 30403 6mm Ball 94003 * Use the screw provided with your servo. 30401 30661 30342 30403 30403 30401 35 ASSEMBLY OF THE RADIO TRAY AND STICK PACK BATTERY 94003 40130 37410 Battery Case 37410 40130 40130 36 ASSEMBLY OF THE RADIO TRAY ONTO CHASSIS Nut 94019 Flat Head...x8 94004 12

37 ASSEMBLY OF THE FUEL TANK ONTO CHASSIS Flat Head 40066 40047 Do Not Over Tighten 40047 38 ASSEMBLY OF THE CLUTCH 10010 10040 38313 10098 Screw Cem en t *Fit the flywheel using a pair of the plier and cross wrench. 10101 *Place the clutch shoes with the clutch springs over the 3 pins of the flywheel. *Using a phillips screw driver or needle nose pliers and bend the small end in the clutch spring behind the pilot shaft 10101 than press down. 39 ASSEMBLY OF THE CLUTCH AND ENGINE MOUNT 3x16mm 3x16mm 3x8mm Washer 34110 5x10x4mm Ball Bearing 5x9x0. Washer Nylon Nut 10399 5x9x0. 3x5mm Cap Screw 3x8mm 34110 30480 3x16mm Cap Screw 3x5mm 34110 30480 13

40 ASSEMBLY OF THE ENGINE ONTO CHASSIS Note book Paper. 10114 5mm Engine Mount Screw *Use note book paper to set gear backlash between spur gear and clutch bell gear, applying pressure while retightening the engine. *If the space is not correct the spur gear will be damaged. 10114 41 ASSEMBLY OF THE MANIFOLD AND MUFFLER 94036 5x4mm Set Screw 49055 10060 94039 4x10mm Flat Head 10185 ZIP TIES 31990 10120 10069 4x10mm 4x4mm 40050 40056 5x4mm 42 ASSEMBLY OF THE THROTTLE LINKAGE 94033 3x Set Screw 2mm Nut...x3 30802 Step 1 2x7mm 30802 2x4mm 30172 2x25mm 30172 Step 3 3x 10300 30802 30172 30531 3x 10300 30802 2x7mm Washer 2x4mm...X2 36140 3x 30802 2x7mm 30802 2x4mm Step 2 2x8mm Step 4 Ensure Free Movement 2x8mm Cut off the servo saver as shown. 30661 94003 2mm 14

43 ASSEMBLY OF THE THROTTLE LINKAGES INTO LEVER 3x 94033 3x Set Screw 10300 10300 5mm Fuel Tube Snap On * Use the screw provided with your servo. 10769 44 ADJUSTING THE ENGINE CONTROL LINKAGES (Neutral) (Throttle High) (Brake) Approx. 0.5mm Idling adjusting Screw Approx. 1mm gap Turn on the Transmitter then Receiver and set the Engine Control Servo Trim to the neutral position. Adjust the idling adjusting screw on the Carburetor to be open approx. 1mm gap. Adjust both of the 10300 Engine Control and Brake linkage accordingly. Adjust the Engine while it is not running. Carburetor is Opening fully Adjust the Servo-Horn mounting position for the Carburetor to be full open. Change the pivot mounting position on the servo horn in case the Carburetor is not opening fully or if it is opening excessively. Or if available on the Transmitter, adjust the Throttle high end point. Adjust so the brakes work smoothly. If the brakes apply too much or not enough, adjust 30800 accordingly. Or if available on the Transmitter, adjust the High-End Brake adjustment. Adjust 30800 to Change the front or Rear Brake.. 45 ASSEMBLY OF THE AIR FILTER 94002 3x8mm 3x8mm 40128 *Apply filter oil to the foam before use. 40127 *Apply filter oil to the foam before use. ZIP TIES 40127 40129 15

37.5mm 28mm 46 ASSEMBLY OF THE FRONT SHOCKS *Assemble 2 for front CORRECT SHOCK ASSEMBLY 41012 1mm Washer 41012 3.5mm O-Ring Fit the o-ring into groove before assembly 41007 41006 40113 41012 41006 41008 41012 41012 40060 2.6x5mm 41011 2.6x5mm 40054 Carefully screw the shock shaft into the bottom of the plastic ball and until the distance between the ballend and the shock body is 28mm for the front. N.B. Do not over tighten as the plastic will strip. 41003 41012 2mm Washer Step 3 Step 4 Fill the shocks with oil. 40643 Step 5 30403 6mm Ball 41005 41015 41013 40113 10mmx1mm O-Ring 40058 1.Pull down piston and pour oil into shock cylinder. 2.To remove air bubbles by slowly moving piston up and down. 3.Pull down piston, attachpressure top and shock oil overflow with tissue paper. 41008 30403 *Cut 7mm for front. 47 ASSEMBLY OF THE REAR SHOCKS *Assemble 2 sets for rear 41012 1mm Washer 41012 3.5mm O-Ring Fit the o-ring into groove before assembly 41007 41006 40113 41012 41006 41008 41012 41012 40060 2.6x5mm 41011 2.6x5mm 40055 Carefully screw the shock shaft into the bottom of the plastic ball and until the distance between the ballend and the shock body is 37.5mm for the rear. N.B. Do not over tighten as the plastic will strip. 41004 41012 2mm Washer Step 3 Step 4 Fill the shocks with oil. 40643 Step 5 30403 6mm Ball 41005 41015 41013 40113 10mmx1mm O-Ring 40058 1.Pull down piston and pour oil into shock cylinder. 2.To remove air bubbles by slowly moving piston up and down. 3.Pull down piston, attachpressure top and shock oil overflow with tissue paper. 41008 30403 16

48 ASSEMBLY OF THE FRONT SHOCK ABSORBER 94041 Nylon Nut 94040 3x8mm Washer 40643 94007 3x20mm 3x8mm 3x20mm Assembly for both right and left side. 49 ASSEMBLY OF THE REAR SHOCK ABSORBER 94041 Nylon Nut 94040 3x8mm Washer 40643 94007 3x20mm 3x8mm 3x20mm Assembly for both right and left side. 50 ASSEMBLY OF THE FUEL TUBE Connect to carbulater. Connect to pressure nipple. Connect to fuel nipple. 10177 Connect to fuel t ank nipple. 10177 17

51 ASSEMBLY OF THE WING 94041 Nylon Nut 40027 Body Reamer (Not included) 40027 16015 94004 Drill two 7mm holes for mounting. 52 ASSEMBLY OF THE TIRES AND WHEELS Apply instant glue into the groove of the wheel. 81095 INSTANT GLUE 86056 86082 53 ASSEMBLY OF THE TIRE ONTO FRONT KNUCKLE AND REAR HUB Assembly for both right and left side. 40550 40550 Wheel Nut 40550 Tire and Wheel assembly. 40550 40550 18

54 ASSEMBLY OF THE BODY AND PAINTING Cut out the body as shown. Use a neutral detergent to remove any dirt and oil. Mask the windows from the inside with masking tape. Apply internal color decals from the inside and paint the body with polycarbonate spray paints. Spray Paint Cutting holes. *Make a 8mm hole for body mount.* *Make a 8mm hole for body mount. Cut out for engine. *Hole for engine. *Hole for fuel tank. *Hole for antenna pipe. *For the exhaust outlet of the muffler. 19

55 MOUNTING BODY 31159 Body Clips 31159 Body Clips 56 STARTING OF THE ENGINE How to start the engine: 1. Turn on transmitter and then receiver. 2. Fill fuel tank with fuel bottle. 3. Connect 1.2V glow plug starter. 4. Start engine with 12V starter. ( Note the direction of the starter.) 5. After the engine be started, remove the 1.2V glow plug starter. 12V Starter and Starter Ring ( Not Included) Starter rubber ring for car. ( Insert starter rubber ring on the 12V starter.) Glow Plug (Not Included) Normal Plug 1.2V Glow Plug Igniter (Not Included) 1.2V Glow Plug Igniter Turbo Plug * Follow the engine manufacturer instruction manuals regarding engine set-up, carburetor and maintenance. 12V Starter There is 2 types of glow plug available "NORMAL or Turbo" depending of the type of the engine. *To start the car, attach a glow plug igniter to the glow plug, and use either an electric starter or starter box applied to the flywheel exposed through the chassis. 1.2V Glow Plug Igniter 1.2V 1.2V 1.2V Glow Plug Igniter Note the direction of the starter. Connect with 12V battery. Starter Box (Not Included) 20

34952 Picco off-road parts list OFNA DESCRIPTION RETAIL OFNA DESCRIPTION RETAIL 10010 CLUCTH SHOES BLACK 3PCS 13.95 40028 DOG BONES, 93MM PAIR LX1 19.95 10040 3 PIN FLYWHEEL,.21 CORN TYPE 14.95 40029 BALL ENDS, PLASTIC, ANTI-ROLL 3.95 10060 MANIFOLD, ROUND EXHT, BLACK 25.95 40031 SERVO SAVER HORN 15.95 10069 SEALS.21, RED ROUND PORT, 2PC 6.95 40032 PLATE, SERVO SAVER,SLIDER H.C. 10.95 10098 CLUTCH NUT, SG SHAFT 4.95 40033 SPRING, SERVO SAVER 3.95 10101 SPRINGS,CLUTCH,GOLD 1.1M 3PCS 4.95 40034 ALUM. RING, SERVO SAVER ADJ.RI 5.95 10114 FLAT HEAD ENGINE MOUNT SCREWS 7.95 40035 AXLE TUBE, SERVO SAVER 35.95 10120 SPRING, MANIFOLD, R.PORT.21 4.95 40036 AXLE POSTS, SERVO SAVER 5.95 10177 FUEL LINE 3FT. GRAY/BLACK 1.95 40037 SCREWS, SERVO PLATE 5.95 10185 SILICONE JOINT TUBE BLACK 4.95 40038 BALLS, 7MM 4PCS. 9.95 10270 CLIPS, FUEL LINE, BLK 3.95 40039 CONE, ALUM. 3MM, 4PCS. 3.95 10282 SWITCH COVER, SILICONE BLACK 3.95 40040 CENTER DIFF MOUNT 4.95 10300 ALUM. STOPPER KIT, 6 PCS. 4.95 40042 BRAKE DISCS, STEEL 4PCS. 10.95 10399 CLUTCH BELL W/BEARINGS, 13T 19.95 40043 CENTER, STEEL DIFF POSTS, 4PCS 13.95 16015 HI FORCE WING, 1/8 WHITE 15.95 40044 SPRING, BRAKE SEPARATORS, 8PCS 5.95 30080 JOINT CAP, 6mm, 2 PCS. 9.95 40045 SCREWS, BRAKE PADS, 4PCS 4.95 30171 LEVER, BRAKE 1.95 40046 STONE GUARDS, 9.5 CHASSIS,BLK 15.95 30172 RODS, BRAKES, 2 PCS. 1.5 40047 BOX, RECEIVER AND BATTERY 14.95 30213 BRAKE CAM 7.95 40050 POST, PIPE HOLDER 6.95 30341 BALL END WITH COLLAR, 6mm 3.95 40051 WIRE, PIPE MOUNT, L-SHAPE 4.95 30342 TURNBUCKLE 3x30mm PICCO 9.5 2.95 40054 SHAFTS,3.5m FRONT SHOCKS, 2PCS 7.95 30401 STEERING ENDS, PLASTIC 6 PCS. 2.95 40055 SHAFTS,3.5m REAR SHOCKS, 2PCS 7.95 30403 6mm BALL, STEEL (NO COLLAR) 4.95 40058 COVERS, SHOCK SHAFTS, SILICONE 9.95 30480 ENGINE MOUNT KIT 12.95 40059 SEALS, 14.7mm O-RING, 4PCS 4.95 30531 SPRING, THROTTLE LINKAGE 2.95 40060 NYLOK NUT, 2.5, PISTON NUT, 4 4.95 30560 ANT TUBE AND MOUNT 2.95 40064 CHASSIS, 9.5 HARD COATED 89.95 30656 WHEEL HUB, LX1, PICCO 9.5 H.C. 11.95 40065 BALL ENDS, PLASTIC, REAR UPPER 4.95 30661 SERVO HORN HEAVY DUTY BLACK 4.95 40066 TANK, 9.5 FUEL 150cc TANK 13.95 30773 CROSS PIN AXLES, 4mm STEEL 3.95 40094 ARMS, FRONT UPPER 9.5 MBX PR. 11.95 30776 WASHER, 4x10x0.2mm 4PCS. 1.95 40113 O-RING P-10 FOR X1-CR,9.5 SHCK 1.95 30802 LINKAGE, 2 THROTTLE LINKAGE 7.95 40127 AIR FILTER SET, X-1 9.95 31159 BODY CLIPS, CHROME 4.95 40128 FOAM, REPLACEMENT FOR 40127 5.95 31990 PIPE, 1:8 TUNED, BLACK 39.95 40129 CONNECTOR, RUBBER FOR 40127 5.95 34053 FRONT UNIVERSALS, PR. COMP2 39.95 40130 PLASTIC BATTERY CASE FOR RTR 7.95 34110 BEARING, 5x10, 2 PCS 6.95 40202 ARMS, LOWER,FRNT&RR 95 MBX 16.95 BEARING, 8x16mm, PAIR 12.95 40512 CENTER DIFF. MOUNT POST 13.95 36055 PIN, 2.5x17mm, HEX HUBS, 4PCS 3.95 40513 DIFF. GEAR (small & large)alum 16.95 36081 REAR UP-RIGHT (8mm BEARING) PR 12.95 40524 FRONT or REAR ARM SHAFT 4x7 6.95 36082 REAR AXLES, 8mm PAIR 10.95 40550 WHEEL NUT 5mm 4.95 36111 REAR BONES, 91mm 2PCS. 95MBX 15.95 40643 PLASTIC SHOCK PARTS,13/16mm 9.95 36140 KNOB, BRAKE ADJUSTER, 2PCS 1.95 41001 SHOCK BIG BORE FRONT 16MM PAIR 79.95 36170 ARM PINS, 4PCS LX1 7.95 41002 SHOCK BIG BORE REAR 16MM PAIR 79.95 36660 BRAKE PAD, 4PCS. 3.95 41003 SHOCK BODY FRONT 16MM PAIR 29.95 36661 BRAKE PAD WASHER, 4PCS. 3.95 41004 SHOCK BODY REAR 16MM PAIR 29.95 36700 STEERING BALL END, 7mm, 8PCS. 6.95 41005 SHOCK CAP 16MM 4PCS. 22.95 36790 4x46MMTURNBUCKLES,4PCS. 10.95 41006 SHOCK SPRING ADJ. 16MM 4PCS. 14.95 36850 7mm BALL, 6 PCS. 3.95 41007 O-RING 19x1.5MM 16MM 4PCS. 4.95 36861 5x40mm TURNBUCKLES, 2 PCS BLK 6.95 41008 PLASTIC SHOCK PARTS 16MM SET 12.95 36901 KNUCKLE, PIVOT BALL (mbx4) 2PC 13.95 41009 CAP SCREWS 3X28MM 4PCS. 2.95 36903 PIVOT BALLS, STEEL (mbx4) 4PCS 7.95 41010 SHOCK BALL END POST LONG 4PCS 11.95 36904 14mm ALUM. NUT (mbx4) 4 PCS 9.95 41011 SHOCK PISTON 16MM 8PCS. 10.95 36905 WASHER PLASTIC, 14mm NUTS 5.95 41012 REPAIR KIT FOR 16MM SHOCK 9.95 37410 BODY CLIPS, 10 PCS. SMALL 3.95 41013 PRESSURE TOP ORANGE 16MM 4PCS. 7.95 38313 CONE, TAPERED 7mm, SG 2.95 41014 SPRING 16MM SUPER SOFT YEL SET 17.95 40001 GEAR, SPUR, 47T STEEL 38.95 41015 SPRING 16MM SOFT WHITE SET 17.95 40003 CASE, DIFF, 1 PC 9.95 49012 GEAR, 13T PINION 7.95 40005 CAP JOINT, BRAKE, 2PCS 13.95 49032 GEAR, BEVEL, 43 TOOTH 29.95 40006 CAP JOINT, FNT&RR DIFF, 2PCS. 13.95 49047 TOWER, FRONT PICCO 9.5 BLACK 14.95 40009 SEAL, P-6 O-RING, DIFF, 2PCS 2.95 49048 ARM HOLDER, FR LOWER BLACK 9.95 40010 PIN, 2.5X13.8MM, DIFF, 2PCS 2.95 49049 ARM HOLDER, RR LOWER BLACK 9.95 40011 GASKET, DIFF 3PCS 3.95 49050 SHOCK TOWER, REAR 4mm BLACK 11.95 40013 BUMPER, FRONT 10.95 49051 PLATE, TOP FR SUPPORT ALUM BLK 7.95 40015 FRONT HOLDER, LOWER ARMS 5PCS 14.95 49052 PLATE, SERVO SAVER SLIDER BLK 8.95 40016 FRONT UPPER ARMS, 1PC 12.95 49053 PLATE, TOP CENTER DIFF BLACK 7.95 40017 MAIN GEAR BOX, FRONT&REAR, 1PC 18.95 49054 RADIO TRAY ALUM. BLACK 12.95 40018 BRACE, CENTER, NYLON, 9.5 KIT 7.95 49055 SPRING AND MANIFOLD FLANGE 4.95 40019 ANTI-ROLL KIT (FRONT/REAR) 13.95 49089 BODY, PRINTED PICCO OFF-ROAD 49.95 40020 ARMS, FRONT&REAR, LOWER PAIR 17.95 81095 FOAM DONUTS, GRAY SET 10.95 40024 SHIM, 13X16XO.2MM, DIFF GEAR,4 2.95 86056 17mm TrueLITES DISH, WHT 6PACK 19.95 40027 WING MOUNT SUPPORT SET 19.95 86082 TIRES, BONES (46)w/FOAM, PAIR 19.95

SETTING GUIDE FRONT CAMBER ANGLE SETTING REAR CAMBER ANGLE SETTING + - - + + - - + Positive Negative Positive Negative Turnbuckle Place the model car on flat surface. Raise the chassis to it's maximum clearance before the wheels leave the ground. Adjust the length of the front and rear upper arms so that the wheels are right angle to the ground. The camber angle adjustment can be moving the turnbuckle rod on the upper arms, clockwise or anti-clockwise. (We suggest use zero degree for the front and 1.5 negative degree for the rear.) *Use 2.5mm hex wrench to adjust upper arm ball in front. FRONT TOE-IN AND TOE-OUT SETTING FRONT SHOCK ANGLE SETTING NEUTRAL POSITION TOE-OUT TOE-IN TOE-OUT Soft 1 2 3 Firm Steering Rod Soft 12 Firm Firm front suspension, less steering. Soft front suspension, more steering. REAR SHOCK ANGLE SETTING Soft 1 2 3 Firm Adjust the length of front steering rod to change thetoe angle. Making the tie rod longer will make the front tires become toe-in. Response will be slower and will over steer. Making the tie rod shorter will make the front tires become toe-out. Response will be quicker and will under steer. Firm rear suspension, over steering. Soft rear suspension, under steering. Soft 123 Firm

OWNER S REGISTRATION CARD OFNA Racing congratulates you on your purchase of our fine OFNA Product. With proper maintenance and handling this kit will provide many hours of enjoyment. The registration card should be filled out and mailed to OFNA Racing within 10 days of purchase date. In the event that the kit is incomplete or component parts are broken due to error in manufacturer, contact your dealer from which you purchased the kit for replacement part or call OFNA at (949) 586-2910 for your nearest dealer location. Other items such as radio and engine other covered by individual warranties. IMPORTANT! Please print or type, filling in the information listed below and mail immediately MAIL TO: OFNA RACING 7 VANDERBILT IRVINE, CA. 92618 TEL: (949) 586-2910 REGISTRATION CARD Write in Your Model Name and Part Number RACER S NAME TEL:( ) ADDRESS CITY STATE ZIP DEALER S NAME TEL: ( ) ADDRESS CITY STATE ZIP OFNA 7 Vanderbilt Irvine, Ca. 92618