Suspension Control Module

User Mnul Suspension Control Module 0099

Before Instlltion Wrning: This owering Module should be instlled by n individul with extensive knowledge in electronics, including: wire identifiction, extrcting nd inserting pins from connector housing. We re not responsible for ny dmge to the owering Module or relted devices due to improper instlltion. Ride eight: To retin proper ride comfort nd to void dmge to suspension components plese follow these minimum recommended height djustments: All non-amg Mercedes models should use setting of or higher. AMG crs re lower thn their Mercedes counterprts. With this in mind it is recommended tht AMG crs use ride height setting of or higher. ower settings cn be used for show purposes but re not recommended for everydy driving. In some models the door must be closed in order for the Airmtic or ABC system to operte. This is sfety function nd is norml on those vehicles. Technicl Support: For further informtion, plese contct

Before Instlltion chssis (M, G) [00+] chssis (R) [ll yers] Airmtic chssis (E) [00 till 0/00] 9 chssis (CS) [till 0/00] 0 chssis (S) [000 00] NOTE: vehicles with -wire level sensor Airmtic chssis (E) [00 from 0//00] 9 chssis (CS) [from 0/00] chssis (S) [00+] NOTE: vehicles with -wire level sensor Airmtic chssis (C) [00+] chssis (C) [00+] 0 chssis (S) [000 00] chssis (S) [00+] ABC 0 chssis (S) [00+] ABC 9 Ride eight Adjustment Vehicle's Connector Preprtion

chssis (M,G) Airmtic 00 + chssis (R) Airmtic ll yers Pin View Suspension Control Module Connector 0 9 0 9 B/ eft Rer B/0 Right Rer R Rer RR Bttery CAN CAN CAN F RF B/9 Right Front B/ eft Front Not Used Not Used Not Used** Not Used** Remote Control Connector Mle pin View Bck View pin Connector Mle * * Ornge Gry White Blue Blue White Blck To Remote Control Connector To Suspension Control Module Connector A I R M A T I C Blck Gry 0 B/0 Right Rer B/ eft Rer * * CAN CAN + V GND B/9 Right Front B/ eft Front 0 *NOTE: Some vehicles of chssis my need these two (sets) pins reversed. If your vehicle rises the rer xle insted of lowering it, then swp these two wires nd there counterprts on the pin connector. (pin & ). **NOTE: Insulte ech unused wire end using electricl tpe 0 9 0 9 0 9 0 9 Airmtic rness, Pin View

STEP-BY-STEP INSTAATION chssis: Airmtic (N) control unit eft front footwell (under the set) Disconnect the Bttery A I R M A T I C chssis: Airmtic (N) with ADS INTO -PIN CONNECTOR Bckview Right front footwell (under pssenger set) Refer to Vehicle s Connector Preprtion for pin removl - see pges -. INTO -PIN CONNECTOR * Bckview White INTO -PIN CONNECTOR * Bckview 9 0

INTO -PIN CONNECTOR Bckview 0 Gry 0 0 INTO -PIN CONNECTOR Bckview 0 Ornge mle bck view 0 9 0 mle front view remote control A I R M A T I C INTO -PIN CONNECTOR Bckview mle bck view mle front view remote control - bttery INTO -PIN CONNECTOR - bttery Bckview mle bck view Blck Blck mle + bttery INTO -PIN CONNECTOR + bttery Bckview mle bck view mle 9 0 Unscrew the Suspension Module screws nd remove the cover Rotte the Function Switch (blck button) to position To continue, go to eight Adjustment chpter

-wire sensors A I R M A T I C B/ Rer B/ Rer chssis (E) Airmtic -wire sensors 00 till 0/00 9 chssis (CS) Airmtic -wire sensors till 0/00 0 chssis (S) Airmtic -wire sensors 000 00 R Rer RR B/ Rer Bttery B/ Rer Airmtic rness, Pin View CAN CAN CAN CAN CAN F RF B/9 Right Front B/9 Right Front + V B/ eft Front B/ eft Front GND 0 Remote Control Connector 9 Mle pin View Bck View B/9 Right Front B/ eft Front 0 0 Pin View 9 0 Ornge 9 Blck 0 9 pin Connector Mle B/9 Right Front B/ eft Front 0 9 Gry White Blue White Blck Gry Blue Suspension Control Module Connector 0 9 0 To Remote Control Connector To Suspension Control Module Connector

STEP-BY-STEP INSTAATION Disconnect the Bttery Right front upper footwell Pull the crpet bck Unscrew bolts holding the luminum brcket Airmtic (N) with ADS Refer to Vehicle s Connector Preprtion for pin removl - see pges -. INTO -PIN CONNECTOR Bckview White -wire sensors A I R M A T I C INTO -PIN CONNECTOR Bckview INTO -PIN CONNECTOR Bckview Blue 9 0 9

-wire sensors A I R M A T I C 0 INTO -PIN CONNECTOR Bckview INTO -PIN CONNECTOR Bckview INTO -PIN CONNECTOR Bckview Blue 0 Gry 0 INTO -PIN CONNECTOR Bckview Ornge mle bck view 9 0 0 0 mle front view remote control INTO -PIN CONNECTOR Bckview mle bck view mle front view remote control 9 0 0

- bttery + bttery Unscrew the Suspension Module screws nd remove the cover INTO -PIN CONNECTOR - bttery Bckview Rotte the Function Switch (blck button) to position mle bck view Blck To continue, go to eight Adjustment chpter INTO -PIN CONNECTOR + bttery Bckview mle bck view Blck mle 9 0 mle -wire sensors A I R M A T I C

chssis (E) Airmtic -wire sensors 00 from 0/00 9 chssis (CS) Airmtic -wire sensors from 0/00 Pin View Suspension Control Module Connector chssis (S) Airmtic -wire sensors 00+ 0 9 0 9 -wire sensors A I R M A T I C B/ Rer R Rer RR Bttery CAN CAN CAN F RF B/9 Right Front B/ eft Front Not Used Not Used Not Used Not Used* Not Used* Not Used* Remote Control Connector Mle pin View Bck View Ornge pin Connector Mle Gry Blue White White Blue Blck To Remote Control Connector To Suspension Control Module Connector Blck Gry 0 B/ Rer CAN CAN + V GND B/9 Right Front B/ eft Front *NOTE: Insulte ech unused wire end using electricl tpe 0 0 9 0 9 0 9 0 9 Airmtic rness, Pin View

STEP-BY-STEP INSTAATION Disconnect the Bttery Right front upper footwell Pull the crpet bck Unscrew bolts holding the luminum brcket INTO -PIN CONNECTOR Bckview Airmtic (N) with ADS Refer to Vehicle s Connector Preprtion for pin removl - see pges -. -wire sensors A I R M A T I C INTO -PIN CONNECTOR Bckview 0 Gry 0 INTO -PIN CONNECTOR Bckview 0 0 0 9 0

INTO -PIN CONNECTOR Bckview Ornge mle bck view mle front view remote control -wire sensors A I R M A T I C - bttery + bttery INTO -PIN CONNECTOR Bckview mle bck view 9 0 INTO -PIN CONNECTOR - bttery Bckview mle bck view Blck mle front view remote control INTO -PIN CONNECTOR + bttery Bckview mle bck view Blck mle mle Unscrew the Suspension Module screws nd remove the cover Rotte the Function Switch (blck button) to position To continue, go to eight Adjustment chpter 9 0

chssis (C) ABC 00 + chssis (C) ABC 00 + Pin View Suspension Control Module Connector 0 chssis (S) ABC 000-00 0 9 chssis (S) ABC 00 + 0 9 R Rer Bttery F Remote Control Connector A B C B/ eft Rer B/0 Right Rer RR CAN CAN CAN RF B/9 Right Front B/ eft Front Not Used Not Used Not Used* Not Used* Mle pin View Bck View pin Connector Mle Ornge Gry White Blue Blue White Blck To Remote Control Connector To Suspension Control Module Connector Blck Gry 0 B/ eft Rer B/0 Right Rer CAN CAN + V GND B/ eft Front B/9 Right Front *NOTE: Insulte ech unused wire end using electricl tpe 0 0 9 0 9 0 9 0 9 Airmtic rness, Pin View

STEP-BY-STEP INSTAATION Disconnect the Bttery chssis: ABC (N/) ctive body control Engine comprtment, left rer A B C chssis: ABC (N/) ctive body control Interior, right front upper footwell 0 chssis: ABC (N/) ctive body control Engine comprtment, left rer chssis: ABC (N/) ctive body control Shown on 0 S0 Interior, right front upper footwell Refer to Vehicle s Connector Preprtion for pin removl - see pges -.

INTO -PIN CONNECTOR Bckview INTO -PIN CONNECTOR Bckview White A B C INTO -PIN CONNECTOR Bckview 0 Gry 0 0 0 0 9 0 INTO -PIN CONNECTOR Bckview INTO -PIN CONNECTOR Bckview Ornge mle bck view mle front view remote control 9 0 INTO -PIN CONNECTOR Bckview mle bck view mle front view remote control

A B C - bttery + bttery INTO -PIN CONNECTOR - bttery Bckview mle bck view Blck INTO -PIN CONNECTOR + bttery Bckview mle bck view Blck mle mle 9 0 Unscrew the Suspension Module screws nd remove the cover Rotte the Function Switch (blck button) to position To continue, go to eight Adjustment chpter

0 chssis (S) ABC 00 + Pin View Suspension Control Module Connector 0 9 0 9 R Rer Bttery F Remote Control Connector A B C B/ eft Rer B/0 Right Rer RR CAN CAN CAN RF B/9 Right Front B/ eft Front Not Used Not Used Not Used** Not Used** Mle pin View Bck View pin Connector Mle * * Ornge Gry White Blue Blue White Blck To Remote Control Connector To Suspension Control Module Connector Blck Gry 0 B/ eft Rer B/0 Right Rer * * CAN CAN + V GND B/ eft Front B/9 Right Front 0 *NOTE: Some vehicles of 0 chssis my need these two (sets) pins reversed. If your vehicle rises the rer xle insted of lowering it, then swp these two wires nd there counterprts on the pin connector. (pin & ). **NOTE: Insulte ech unused wire end using electricl tpe 0 9 0 9 0 9 0 9 Airmtic rness, Pin View 9

STEP-BY-STEP INSTAATION Disconnect the Bttery 0 chssis: ABC (N/) ctive body control Ner steering column Interior, left footwell A B C Refer to Vehicle s Connector Preprtion for pin removl - see pges -. INTO -PIN CONNECTOR Bckview * INTO -PIN CONNECTOR Bckview White * INTO -PIN CONNECTOR Bckview 0 Gry 0 0 0 0 9 0 INTO -PIN CONNECTOR Bckview 0

INTO -PIN CONNECTOR Bckview Ornge mle bck view mle front view remote control 9 0 INTO -PIN CONNECTOR Bckview mle bck view mle front view remote control A B C - bttery INTO -PIN CONNECTOR - bttery Bckview Blck Blck mle mle bck view + bttery INTO -PIN CONNECTOR + bttery Bckview mle bck view mle 9 0 Unscrew the Suspension Module screws nd remove the cover Rotte the Function Switch (blck button) to position To continue, go to eight Adjustment chpter

Ride eight Adjustment Ride eight Adjustment Rotte ll four Wheel eight Adjustment Switches Plug in the Suspension Reconnect the bttery. EDs (gry buttons) Control Module. in the Suspension to position (medium height). Module should blink. Cycle the ignition key On then Off (do not strt the engine). Strt the engine. Mke sure you re prked on n even surfce. Press the fctory Vehicle eight button (button ED On). Wit up to 0 seconds until vehicle rises. Press the button gin to lower the vehicle (button ED on the button will turn Off). Wit up to 0 seconds. Adjust individul Wheel eight Adjustment Switches if required (to see the height chnging, perform the next step). Cycle the Vehicle eight button gin (button ED On then Off), with up to 0 seconds in-between. 9 If still not stisfied, go bck to step. Replce the Suspension Module cover. Congrtultions! The vehicle hs been lowered. 0

Function Switch (see instlltion instructions): 0 = Suspension Module Off (EDs,,, sty On) = Suspension Module On (ED is ON, EDs,, blink) = Suspension Module On (ED is ON, EDs,, blink) = Suspension Module On (EDs,,, blink),,, = Suspension Module Off (EDs,,, sty On) eft Front Adjustment Switch NOTES: ED ED eft Rer Adjustment Switch Right Front Adjustment Switch - If Remote Control is being used, refer to the operting instructions in its user mnul. - It is quite common tht even before the instlltion individul wheels re not t the sme level. This is more noticeble when the vehicle is lowered. Smll differences cn be mnully djusted by rotting the individul Wheel Switches. rger differences should be corrected t the deler using proper equipment nd procedure. Before going to the deler, remember to turn off the Air Suspension Control Module by rotting the Function Switch (blck button) to position 0. Once bck from the deler, rotte the Function Switch bck to originl position or, s described in the Step-by-Step Instlltion. - The proceeding lowering vlues re n pproximtion nd will vry from wheel to wheel nd vehicle to vehicle: ED ED Right Rer Adjustment Switch Function Switch Ride eight Adjustment Wheel eight Adjustment Switch positions : lower by / [0 mm] : lower by / [0 mm] : lower by [ mm] : lower by / [0 mm] : lower by / [ mm] : lower by / [0 mm] : lower by / [ mm] 0: lower by [0 mm]

Vehicle's Connector Preprtion DISCONNECTING the pin connector from the lowering module CONNECTING the pin connector to the lowering module 0 pin nd pin Connector Disssembly Remove cp by pushing nd removing housing from plug by unlocking the two ltches on the sides of the housing. Then slide heder outwrd. END CAP EADER Plug tch tch Sliding OUSING Extrcting the pins from the housing Side Cp Disssembly nd re-ssembly To instll: INSERT AND PUS To remove lrger pins use extrction tools AZET - To remove smll pins use extrction tools AZET 9- + - or solid thin wire To remove: PUS UPWARD

Extrcting nd Inserting pins EXTRACTING the smller pins from the housing Use AZET Tool No.: - nd ndle No.: 9- EXTRACTING the lrger pins from cr connector To Remove lrge pins use AZET Tool No.: - or solid thin wire Inserting the pins bck into the connector housing In the 0 pin cr connector use extrction tools AZET 9- nd - or solid thin wire. pin femle connector Insert heder with wires into housing To remove smll pins use extrction tool AZET 9- or solid thin wire.

Comments

Designed, engineered nd mnufctured by ProgRm, Inc. www.progrminc.com CM-0 M-MIS-90/.0