Nozzles, oiling-brushes, reservoirs and other accessories for the chain lubrication 1-106-EN
16 10,5 16 10,5 ~ ~ Chain lubrication, accessories Oil projection nozzle AC-A Compact design, pinpoint accuracy, high temperature resistant, the projection nozzles AC-A suit perfectly to aggressive surroundings. These nozzles are spraying, straight and without air, microdosis of oil under pressure, which are delivered by pneumatic or electromagnetic micropumps. The spray distance can vary from a few centimeters up to several decimeters. AC-A nozzles spray mineral or synthetic oil with a viscosity of 100 mm 2 /s at 0 C. The nozzle have a stainless steel body, fluorocarbon (FPM) seals and are equipped with a check valve. They are fed via tubes OD with a max. length of m. Note The tubes have to be imperatively metallic, as direct as possible, and without connector on the pump/ nozzle line. The inner diameter of the tube shall not exceed mm. AC-A-20 Order information Order No. Possible volume 1) [mm /stroke] Number of outlet(s) outlet Ø [mm] Valve 2) [bar] Temperature [ C] Seal Fixing Weight [g] AC-A-10 10/60 1 0,5 6 - to +220 FPM M 8 1, ~ AC-A-10-1 10/60 1 0,5 6 10 to 220 - M 8 1, ~22 AC-A-10-2 10/60 1 1,5 2 - to +220 FPM M 8 1, ~ AC-A-20 2 ~0 ) 2 0,5 6 - to +220 FPM Ø 8,5 ~50 1) The volume depends on the pump or distributor flow rate. 2) Valve setting at 20 C for an oil with recommended viscosity ) For a supply volume of 60 mm AC-A-10 AC-A-10-1 (Ø0,5) () (Ø0,5) () Ø2,5 / Ø Ø2,5 / Ø (11,55) SW10 (11,55) SW10 SW10 SW10 SW10 SW10 SW1 SW1 M8 max. (Ø1,5) M8 max. (Ø1,5) 2 1-106-EN
6,5 26 ~60 1,6 Chain lubrication, accessories AC-A-10-2 AC-A-20 Ø 1,5 () Ø2,5 / Ø Ø 2,5 / Ø (11,55) (SW10) H.10 H.12 SW.1 (SW10),5 10 (SW10) (SW1) ~0,5 1,7 10,5 M8 max. (Ø2,5) Ø18 Fixation support Fixation support (nut and adjustable support for threaded nozzles) Order No..... UC-1065 (Ø) (Ø) UC-1065 Note Many factors have an influence on the projection quality: (M6) 12 56 1 10 8,5 10 160 6,5 (27) (12) (27) (12) (1) (2,) 28 = = (AC-A-10-1) (M8) (M8) (10) the lubricant viscosity the temperature the tube length the expected projection frequency Therefore the result of the projection differs according to the application. (AC-A-10) (8,5) 1-106-EN
Oiling brushes Oiling brushes UC are used to apply lubricant to a chain. They ensure a constant lubricant film on the chain. These brushes are available in different shapes and sizes and with different materials (bristle, brass or polyamide) in order to better meet the needs and specification of the chains. The brushes are fed with tubes Ø 0,75. Brushes are delivered without bracket supports, which have to be ordered separately. Order information Order No. Shape Sizes [mm] Temperature [ C] Brush material Fixation [mm] Weight [g] Bracket support Order No. UC-1066-01 55 16 10 to 60 Bristle Ø 8,5 110 AC.2879 UC-1066-02 55 16 10 to 200 Brass Ø 8,5 160 AC.2879 UC-1066-0 Ø 0 10 to 60 Bristle Ø 19 85 UC.1010.100 UC-1066-0 Ø 10 to 60 Bristle Ø 12,5 5 AC.98 UC-1066-05 Ø 10 to 80 Polyamide 6.6 Ø 12,5 5 AC.98 UC-1066-06 55 16 10 to 80 Polyamide 6.6 Ø 12,5 5 AC.2879 UC-1066-01 ; UC-1066-06 UC-1066-02 6 Ø5,5 Ø6 5,5 101 ~55 ~17 85 min. / max. 70 ~55 ~17 85 min. / max. 70 7 109 1-106-EN
UC-1066-0 UC-1066-0 ; UC-1066-05 Ø9 Ø9 Ø0 5 65 1 60 Ø 50 6 0 min. 1 / max. 80 85 min. / max. 70 Retractable oiling brushes AC-A-216 Retractable brushes with volumetric oil supply, driven by a motor pump. These brushes are in contact with the chain only during the lubrication phases, which are controlled by a control unit. This control unit can set the brushes contact time with the chain, the oil injection frequency and the time between two lubrication phases. During a pause phase the brushes are lifted up to limit brushes wear. Model AC.A.210: retractable brushes without metering unit. Order information Order No. Shape Volume [mm ] Quantity Sizes [mm] Temperature [ C] Brush material Fixation [mm] Ø tube [mm] Weight [g] AC.A.216.20 20 2 55 16 10 to 60 Bristle 2 Ø6,5 8 1 90 AC.A.216.0 0 2 55 16 10 to 60 Bristle 2 Ø6,5 8 1 90 AC.A.210 55 16 10 to 60 Bristle 2 Ø6,5 8 1 & 0,75 600 1-106-EN 5
Oil reservoirs These reservoirs, with a capacity of, l to 20 l, supply with lubricant the pneumatic or electromagnetic pumps of the chain lubrication system. They can be equipped with a stopcock valve for maintenance tasks on the lubrication system. The lubricant min. level can be visually (sight glass) or electrically (level switch) monitored. On request: Some reservoirs have an electric preheating device in order to maintain the lubricant at the optimal operating temperature. It is also possible to have some reservoirs with level switch with two switching points (warning and minimal). Order information Order No. Capacity [l] Material Min. level switch Stopcock valve Filter [µm] Operating temperature [ C] TK-0-VMC. PE 200 (outlet) -10 to +60 1,2 TK-80-V 10 aluminum 00 (inlet) -10 to +60 6,5 TK-80-VM 10 aluminum 00 (inlet) -10 to +60 6,0 TK-90 20 aluminum 00 (inlet) -10 to +60 Weight (ca.) [kg] TK-0-VMC TK-0-VMC 1. Filling plug with filter 2. Min. level switch (with connector), NO, when the min. level is reached the contact opens.. Stopcock valve. Outlet port with filter G 1/, max. depth 9 mm 28 ~27 1 178 16 210 2 PG9 5 H.21 16 Ø7 7 16 168,5 200 16 56 127 6 1-106-EN
TK-80-V / -VM Reservoir type TK-80 1. Min. level switch (with connector), changeover switch 2. Breather. Filling port Ø RP 1/. Filling plug with filter 5. Sight glass 6. Outlet port G 1/ 7. Stopcock valve 10 286 2 Ø11 50 5 PG11 19 Level switch When min. filling level is reached. contact 1-2 opens contact 1- closes 278 (5) (22) 5 7 5 266 (~298) 6 1 2 2 1 option (60) TK-90 TK-90 1. Breather 2. Filling plug with filter. Sight glass. Min. level switch (with connector), changeover switch 5. Outlet port G 1/, max. depth 9 mm 6. Stopcock valve Level switch When min. filling level is reached. contact 1-2 opens contact 1- closes 2 1 02 90 12 66 102 286 PG11 60 280 2 8 Ø11 6 1 6 19 5 1-106-EN 7
Proximity switch The inductive proximity switches are essential for the chain lubrication systems. They detect with accuracy and without any mechanical contact to the chain the position of the lubrication points on the running chain. When a lubrication point has been detected, the proximity switch sends a signal to the control unit, which triggers a lubrication impulse (actuation of the pump). The proximity switches are delivered with the connector or the cable, and the bracket support. Order information Order No. Type Nominal sensing distance (Sn) Operating voltage Service temperature [ C] Housing UC-1060-11 wires, PNP, NO mm 12 to 2 V DC - to +80 plastic, IP67 UC-1060-1 wires, PNP, NO 5 mm 10 to 0 V DC -0 to +175 metal, IP67 UC-1060-16 wires, PNP, NO 5 mm 12 to 8 V DC - to +80 metal, IP68 UC-1060-17 2 wires, NO 5 mm 2 to 20 V AC / 2 to 210 V CC - to +80 metal, IP68 UC-1060-19 wires, PNP, NO 10 mm 10 to 0 V DC - to +70 metal, IP67 UC-1060-11 washer M6 8,5 0 rail 28 (welded on the machine) 77 (60) UC-1060-1 washer M6 8,5 7,5 160 (28) 19 9 (28) 19 1 2 connector PG7 5 58 (M0 1,5) (1,5) 6 50 20 72 110 PNP NO wiring diagram brown/1 (BN) (power) black/ (BK) (Signal) blue/ (BU) (power) load + Ø,7 - rail 28 5 m 80 10 70 58 (M18 1) (28) (2) 20 72 110 wiring diagram brown/1 (BN) (power) black/ (BK) (Signal) load blue/ (BU) (power) 8 1-106-EN
UC-1060-16 0 washer M6 (28) 8,5 19 rail 28 (welded on the machine) 100 82 50 58 (M18 1) (27) (2) 20 72 110 wiring diagram brown/1 (BN) (power) black/ (BK) (Signal) load blue/ (BU) (power) connector PG7 washer M6 8,5 0 UC-1060-17 (28) 19 rail 28 (welded on the machine) 60 58 (M18 1) (27,7) 20 72 110 brown/2 (BN) blue/ (BU) load,8 51,5 wiring diagram Ø cable 2 0,5 mm², 2m UC-1060-19 washer M6 8,5 0 (28) 19 rail 28 (welded on the machine) ~88 (~71) 5 50 58 (M0 1,5) (1,5) 6 50 20 72 110 wiring diagram brown/1 (BN) (power) black/ (BK) (Signal) load blue/ (BU) (power) connector PG7 1-106-EN 9
Connection kits: reservoir / pumps SKF offers several connection kits to connect the reservoir to the pump(s) PE. These kits differ in terms of the outlet connector G 1/ (straight or elbow) and the number of pumps. Order information Order No. Reservoir outlet Pump(s) Description UC-1070-1 straight 1 straight connector ( 1), copper seal ( 1), steel tube (1 m), banjo fitting ( 1) UC-1070-2 straight 2 straight connector ( 1), copper seal ( 1), steel tube (1 m), banjo fitting ( 2), T connector ( 1) UC-1070- straight straight connector ( 1), copper seal ( 1), steel tube (1 m), banjo fitting ( ), cross connector ( 1) UC-1070- straight straight connector ( 1), copper seal ( 1), steel tube (1 m), banjo fitting ( ), T connector ( ) UC-1071-1 elbow 1 elbow connector ( 1), steel tube (1 m), banjo fitting ( 1) UC-1071-2 elbow 2 elbow connector ( 1), steel tube (1 m), banjo fitting ( 2), tee connector ( 1) UC-1071- elbow elbow connector ( 1), steel tube (1 m), banjo fitting ( ), cross connector ( 1) UC-1071- elbow elbow connector ( 1), steel tube (1 m), banjo fitting ( ), tee connector ( ) UC-1070- (for reservoir with straight outlet connector) UC-1071- (for reservoir with elbow outlet connector) Connection kit for pumps PE reservoir straight outlet TK-... 508-108 ( 1) 10-0W ( 1) TK-... 10-05W ( 1) reservoir elbow outlet WV-RO10x1VERZI (x1m) oil 10-07 ( ) oil Ø 8 10 pumps (PE--...) 5-516-101 ( ) (PE--...) (PE--...) (PE--...) Connectors and tubes for the connection reservoir / pump Order No. Copper washer... 508-108 Straight screw-in connector... 10-0W Elbow screw-in connector... 10-05W Steel tube Ø8 10... WV-RO10x1VERZI Banjo fitting.... 5-516-101 Tee connector... 10-07 Cross connector.... 6-10-001 Straight connector* for tube OD 10... 10-10 Flange* for tube OD 10... 610-001 *) These parts are not included in the kits 10 1-106-EN
Connection pumps / nozzles or brushes Connectors and tubes for the connection pump/nozzles or brushes Connection pump / nozzle Order No. Steel tube Ø 0,7... WV-ROx0,7VERZI Connector (pump outlet)... 0-002 Double tapered sleeve (pump outlet)... 0-001 Connection pump / brush Steel tube Ø 0,7.... WV-ROx0,7VERZI Connector (pump outlet)... 0-002 Double tapered sleeve (pump outlet)... 0-001 Hose, polyamide, Ø 2,5... TU-2.5x-RL Reinforcing socket (pump outlet)... RB.01 Tapered sleeve (pump outlet)... 0-611 Connector (pump outlet)... 0-612 *) Nozzles and brushes are delivered with their own fittings. Connection pumps / nozzles or brushes PE-... RB.01 ( 1) 0-611 ( 1) 0-612 ( 1) TU-2.5X-RL oil Ø8x1 0-001 ( 1) 0-002 ( 1) WV-ROX0.7VERZI NOZZLE AC-A-... Ø BRUSH UC-1066-... Ø 1-106-EN 11
Drip pan The drip pans are designed for the electromagnetic pump PE. They prevent any pollution in the case of leakage at the connections or during maintenance tasks. Technical data Drip pan SY.9581.1 Drip pan for 1 pump PE* Capacity...0,7 l Material... steel 1 Ø11 6 Order No..... SY.9581.1 *) The drip pan is delivered with screws and washers for the fixation of the pump. 2 5 2 M8 26 110 0 180 0 = = 120,5 200 20 Technical data Drip pan for 2 pumps PE* 1 Ø11 Drip pan SY.9581.2 6 Capacity...1, l Material... steel Order No..... SY.9581.1 2 *) The drip pan is delivered with screws and washers for the fixation of the pumps 5 26 5 6 M8 200 20 270 = =,5 0 120 200 20 12 1-106-EN
Technical data Drip pan GR.271.7 Drip pan for 1 pump PE* Capacity...10, l Material.... steel Order No..... GR.271.7 175 Ø11 110 105 *) The drip pan is delivered with screws and washers for the fixation of the pump. 2 121 5 = = 2 M8 00 0 70 75 0 120 200 0,5 Technical data Drip pan GR.271.8 Drip pan for 2 pumps PE* Capacity...10, l Material.... steel Order No..... GR.271.8 175 Ø11 110 105 *) The drip pan is delivered with screws and washers for the fixation of the pumps 2 76 5 6 5 = = M8 00 0 70 0 120 75 200 0,5 1-106-EN 1
Notes 1 1-106-EN
1-106-EN
No.: 1-106-EN Subject to change without notice! (10/201) Important information on the use of products All SKF products may be used strictly respecting the instructions described in this brochure or the operating instructions. If the operating instructions are supplied with the product, they must be read carefully and respected. None of the lubricants is compatible with the centralized lubrication systems! On the user's demand, SKF can check the compatibility of the lubricant chosen with the centralized lubrication systems. All products or their components manufactured by SKF are incompatible with the use of gas, liquefied gases, vaporized gas under pressure, vapors and any fluid with a vapor pressure greater than 0.5 bar at normal atmospheric pressure (101 mbar) for the maximum permissible temperature. More specifically, we call your attention to the fact that hazardous products of any kind, especially products classified as hazardous by the EC Directive 67/58/EEC, Article 2, paragraph 2, can only be used to feed the SKF centralized lubrication systems, transported or distributed by these systems after consultation with SKF and obtaining written permission. Further brochures: 1-9201-EN Transport of Lubricants in Centralized Lubrication Systems This brochure was presented by: SKF is a registered trademark of the SKF Group. SKF Group 201 The contents of this publication are the copyright of the publisher and may not be reproduced (even extracts) unless prior written permission is granted. Every care has been taken to ensure the accuracy of the information contained in this publication but no liability can be accepted for any loss or damage whether direct, indirect or consequential arising out of the use of the information contained herein.