Flow limiter SP/SMB 8... DSK US (09.04)
|
|
- Maud Richard
- 6 years ago
- Views:
Transcription
1 DSK US (09.04) for mounting plates General information s are used in large oil circulation lubrication systems. The task of a flow limiter is to divide up the volumetric flow of the main line into parallel individual volumetric flow quantities and to limit these according to requirement, or to keep them constant. The volumetric flow generated is independent of the system pressure and virtually independent of viscosity. The flow limiter was developed specially for mounting plates. The advantage of this design is its simple and compact construction. Using interchangeable plug-in nozzles, the volumetric flow of the flow limiter can be set stepwise from 0.09 to 8.18 l/min. This also makes subsequent adjustments possible (necessary when the unit is modified, e.g.). Tedious resetting and measuring are unnecessary. SP/SMB 8... The volumetric flow can be monitored simply and safely with a signal transmitter or proximity switch (which is also subsequently screwed in). A fault signal occurs when the volumetric flow drops to approx. % of the nominal volumetric flow. Mode of operation Functional diagram With the flow limiter, the total volumetric flow Q is divided up by the parallel layout of the on the mounting plate into individual flow lines Q i. The system pressure, being the input pressure p 1 is thus maintained for all flow limiters. Every has a control plunger with a plug-in nozzle as a differential pressure regulator. The differential pressure (p 1 -p 2 ) at the interchangeable plug-in nozzle D 1 in the control plunger is based on a balance of forces p 1 A = p 2 A + F resp.. p1/2 = p 1 - p 2 = F/A = constant. It follows that: The difference in pressure in front of and behind the variable jet D 2 is maintained constant by a balance in pressure. The condition for this function is that the system pressure p 1 is always greater than the sum of the pressure drops in and after each flow limiter. p 1 > p1/2 + p 3 For this reason the pump volume flow should exceed all individual flow quantities by approx. 15 %, i.e., Q = 1.15 ( Q i ). p 1 pressure upstream of the plug-in nozzle D 1 p 2 pressure downstream of the plug-in nozzle D 1 p 3 pressure downstream of D 2 D 1 D 2 RK F A plug-in nozzle throttle control plunger spring pressure cross-section of the control plunger Fig. 1 Functional diagram SP/SMB 8.
2 DSK US (09.04) 2 Design Switchposition at a clogged Nossle E2 E3 Working position / correct flow +24V,DC 1 ~ Casing 2 Bush Switch position at a lack of pressure / Flow 3 Spring-loaded control plunger 4 Interchangeable plug-in nozzle 5 Pressure spring 6 Signal transmitter (optional) 7 Switching piston of the signal transmitter (with a built-in signal transmitter) 8 Mounting plate Fig. 2 Design of flow limiter SP/SMB 8/2E2... for mounting plates 3 green green Note! Sensor E3 is no longer available. Please note the modified wiring diagram for successor model E4. 2 Switchposition at a clogged Nossle E4 Working position / correct flow green yellow 1 Casing 2 Bush Switch position at a lack of pressure / Flow 3 Spring-loaded control plunger 4 Interchangeable plug-in nozzle 5 Pressure spring 6 Signal transmitter (optional) 7 Switching piston of the signal transmitter (with a built-in signal transmitter) 8 Mounting plate Fig. 3 Design of flow limiter SP/SMB 8/2E4... for mounting plates 8,5 8, Outlet M6 32 Inlet E2, E3 E Expanded length Expanded length Fig. 4 Design of flow limiter SP/SMB 8... with signal transmitter for mounting plates Outlet M6 Inlet LED PNP 16 Expanded length 1 + Load 2 Fig.5 Design of flow limiter SP/SMB 8... with proximity switch for mounting plates - 3
3 DSK US (09.04) 3 Technical Data flow limiter General information Type... 2-way flow limiter valve Application... for mounting plates Equipment... with fastening screws M 6 45 and sealing rings Fitting position... random (by mountig with filter mounted filter vertically downwards) Ambient and lubricant temperature range... 0 to C Material... AlCuPb F38, neutrally anodized Weight kg Hydraulics Nominal volumetric flow (see also related tables, Page 4 to 5) stepwise... from 0.09 to 8.18 l/min Working pressure p 1 without adaptations... 5 to 200 bar Working pressure p 1 with signal transmitter...5 to 85 bar Working pressure p 1 with proximity switch... 5 to 200 bar Required differencial pressure between input pressure p1 and output pressure p bar Lubricant... mineral oils and synthetic oils Operating viscosity to 600 mm²/s Signal transmitter Type... magnetic switch Switching element/contact type... magnetic/reed contact Ambient and lubricant temperature range - E to C - E to + 90 C Material - Casing... AlCuMgPb F38, neutrally anodized - Connector... polyamide Weight... 0,2 kg Switching voltage V to 230 V AC/DC Switched current A [24 V] or 0.17 A [230 V] 1 ) Switching capacity... max. 40 W Function... NC (Go position normaly closed) Type of protection... IP 65 2 ) Connection - E2... plug, 230 V - E4... plug, M 12x1, 4pol, 24 V DC with a green and yellow LED 3 ) Connection lines... screwed Cross section for connection - E2... max. 2 1 mm² - E4... max. 3 1 mm² Cable diameter... max. 10 mm Proximity switch Type... inductiv PNP (normaly closed) Monitoring... yellow LED, lights in Go state Operating voltage to 36 V DC current raiting ma Operating temperature C bis 80 C Switching distance mm Short circuit protection... included Max. pressure bar Typ of enclosure (DIN ) IP 67 Key to order codes - for mounting plates - (see also Plug-in nozzle tables pages 4 to 5) Order description Part number SP/SMB 8/2 / _ Nozzle type /0 = without signal transmitter E2 = with signal transmitter and connector up to 230 V AC, without LED E4 = with signal transmitter and connector up to 24 V DC, with green and yellow LED, Connection coupler socket M12x1) E6 = with Proximity switch Nozzle type 0 = without signal transmitter 2 = with signal transmitter and connector up to 230 V AC, without LED 7 = with signal transmitter and connector up to 24 V DC, with two LED) 6 = with Proximity switch (12 bis 36 V DC) 4 ) 1) Sufficient spark protection required. 2) Previous model only in combination with transistor relay. 3) Green and yellow LEDs light when Go signal received, when yellow LED goes out => fault signal. 4) Socket optional, for order see accessories page 8.
4 DSK US (09.04) 4 Table Plug-in nozzles Nominal volumetric Plug-in nozzle D 1 flow 1 ) Order description Part Number Complete spare part [l/min] [ mm] [Type] Part number SP/SMB 8/ _ / _ _ /045 - _ _ /050 - _ _ /055 - _ _ /060 - _ _ /065 - _ _ /0 - _ _ /075 - _ _ /080 - _ _ /085 - _ _ /090 - _ _ /095 - _ _ /100 - _ _ /105 - _ _ /110 - _ _ /115 - _ _ /120 - _ _ /125 - _ _ /130 - _ _ /135 - _ _ /140 - _ _ /145 - _ _ /150 - _ _ /155 - _ _ /160 - _ _ /165 - _ _ /1 - _ _ /175 - _ _ /180 - _ _ /185 - _ _ /190 - _ _ /195 - _ _ /200 - _ _ /205 - _ _ /210 - _ _ /215 - _ _ /220 - _ _ /225 - _ _ /230 - _ _ /235 - _ _ /240 - _ _ /245 - _ _ /250 - _ _ /255 - _ _ /260 - _
5 DSK US (09.04) 5 Nominal volumetric Plug-in nozzle D 1 flow 1 ) Order description Part Number Complete spare part [l/min] [ mm] [Type] Part number SP/SMB 8/ _ / _ _ /2 - _ _ /275 - _ _ /280 - _ _ /285 - _ _ /290 - _ _ /295 - _ _ /300 - _ _ /305 - _ _ /310 - _ _ /315 - _ _ /320 - _ ) in operating viscosity 300 mm²/s. Oil filter with shut-off valve Material... AlCuMgPb F38, neutrally anodized Mesh spacing mm Weight kg Dummy element Application... to blank off unused mounting plate outlets Material... AlCuMgPb F38, neutrally anodized Model:... with mounting screws M6 45 and sealing rings Weight kg/pc Order Information Oil filter with shut-off valve... Part number Order information Dummy element... Part number approx.130 G 1/ M wrench SW Fig. 6 Oil filter with shut-off valve Fig. 7 Dummy element for flow limiter
6 DSK US (09.04) 6 Mounting plate for a flow limiter with interchangeable strainer (40) Expanded lenght Material... AlCuPb F38, neutrally anodized Mesh spacing interchangeable strainer mm 30 Weight kg 15 Ø Order Information Mounting plate for a flow limiter with interchangeable strainer... Part number SW27 Mounting plate for 1 to 6 flow limiters G3/ Input G3/8 Fig. 8 Mounting plate for a flow limiter with interchangeable strainer Material... AlCuMgPb F38, neutrally anodized Weight... see table (40) Ø Number Dim. L Dim. L 1 Weight Part number flow limiter [n][mm] [mm] [kg/part] Ø Inlet G 1/ L1 G 3/8 Fig. 9 Dimension drawing of mounting plate for 1 to 6 flow limiters SP/SMB 8.. Mounting plate for 1 to 6 flow limiters and oil filter Material... AlCuMgPb F38, neutrally anodized Weight... see table Number Dim. L Dim. L 1 Weight Part number flow limiter [n][mm] [mm] [kg/part] , , , , , , Fig. 10 Dimension drawing of mounting plate for 1 to 6 flow limiters and oil filter
7 DSK US (09.04) 7 Example of an oil circular lubrication system The pump (1) delivers the lubricant to the main line (2). From here, the lubricant then reaches the lubricating point directly via the flow limiter (4), or via the progressive distributor (3) or flow divider (6) which are connected to it. The signal transmittersor proximity switches which are screwed into the flow limiters (4) monitor the volumetric flow. Collective monitors (5) evaluate the entering signals. 1 Pump 2 Main line 3 Progressive distributo 4 flow limiter with signal transmitter 5 Collective monitor 6 Flow divider Replacing plug-in nozzles Interrupt oil feed to flow limiter above shut-off valve (at oil filter, if required). control plunger held under spring pressure! Remove stop screw (hexagonal 30 mm) or signal transmitter or proximity switches with sealing ring slowly Caution! Escaping oil may be hot! Remove control plunger, plug-in nozzle with sealing ring and pressure spring. Remove plug-in nozzle from control plunger. Use a rod approx. ø 7 in diameter, if necessary, (on no account a pointed instrument such as a needle). Insert new plug-in nozzle with sealing ring into the control plunger as far as it will go. Insert pressure spring (without crossing the thread) into the bore hole. Insert control plunger with new plug-in nozzle on top of the pressure spring into the bore hole without crossing the thread. Check control plunger for smooth action by pressing against the pressure spring. Crossing the thread causes malfunctions. Screw in stop screw or signal transmitter with sealing ring. Open shut-off valve Fig. 11 Example of an oil circular lubrication system 1 flow limiter 2 Bush 3 Control plunger 4 Interchangeable plug-in nozzle 5 Pressure spring 6 Mounting plate 7 Stop screw Fig. 12 Replacing plug-in nozzles on flow limiter
8 DSK US (09.04) 8 Accessories Proximity switch Sockets straight, 4-poles, M 12x Sockets angled, 4-poles, M 12x Sockets straight, 4-poles, M 12x1 with orange cable 5 m Sockets angled, 4-poles, M 12x1 with orange cable 5 m Other publications Electric Plug-and Socket Connectors Replacement parts Designation Part number without nozzle, signal transmitter Gasket set for Signal transmitter Version E2 Signal transmitter without coupler socket Signal transmitter with coupler socket E2 (230 V AC) Coupler socket E2 (230 V AC) Signal transmitter Version E4 Signal transmitter without coupler socket Signal transmitter with coupler socket ( 24 V DC) Coupler socket (24 V DC) Proximity switch Proximity switch General Interchangeable strainer, mesh spacing 300 µm Gasket set for interchangeable strainer Filter insert, filter fineness 100 µm Gasket set for filter Please note: All VOGEL products must be used correctly. If operating instructions are supplied with the products, any additional device-specific instructions and information given in those operating instructions should be applied. Please note, in particular, that hazardous materials of any type, particularly materials that are classified as hazardous in EU Directive 67/548/EEC, article 2, para. 2, must not be used to fill or be pumped and/or distributed by VOGEL central lubricationsystems and components without the prior written approval of VOGEL. No products manufactured by VOGEL are approved for use with gases, liquefied gases, gases that are released under pressure, vapours and any liquids with a vapour pressure of more than 0.5 bar above normal atmospheric pressure (1013 mbar) at the maximum permitted temperature. Willy Vogel AG Motzener Strasse 35/ Berlin, Germany PF Berlin Tel. +49 (0) Fax +49 (0) info@vogel-berlin.de Willy Vogel AG 2. Industriestrasse Hockenheim Germany Tel. +49 (0) / 27-0 Fax +49 (0) / info@vogel-berlin.de VOGEL France SAS Rue Robert Amy, B.P Saumur cedex France Tel. +33 (0) Fax +33 (0) info@vogelfrance.com We reserve the right to make amendments. 09/2004
Flow limiter SP/SMB US
Flow limiter SP/SMB 13... 1-3004-US for installation in the lines of circulating-oil lubrication systems General information Flow limiters are used in large circulating-oil lubrication systems. The task
More informationFlow limiter SP/SMB3 Flow limiter SP/SMB6
-00-EN Flow limiter SP/SMB Flow limiter SP/SMB6 for circulating-oil lubrication systems Advantages reliable perpetual dispensation of individual volume flows - self-adjusting metering, thus identical volume
More informationFlow limiter SP/SMB9 for mounting plates
1-3002-EN Flow limiter SP/SMB for mounting plates Advantages reliable perpetual dispensation of individual volume flows - self-adjusting metering, thus identical volume flows despite different back pressures.
More informationFlow limiter SP/SMB10 Dual flow series
1-00-EN Dual flow series Advantages reliable - Parallel distribution of individual flow quantities - self-regulating metering with pressure balancing valve, thus constant volumetric flows even for different
More informationFlow limiter SP/SMB13 for line installation in circulating-oil lubrication systems.
1-3004-EN Flow limiter SP/SMB13 for line installation in circulating-oil lubrication systems. Flow limiters are used in circulating-oil lubrication systems. The task of a flow limiter is to divide up the
More informationGrease-lubricating pump FF... DSK US (05.05)
Grease-lubricating pump FF... DSK 2-008-00-US (05.05) electrically operated, for small and medium-sized multiple-line and progressive systems PSG-2 with cycle switch VPB with cycle switch PSG-2 with cycle
More informationInjection Oilers, Micro Pumps
Injection Oilers, Micro Pumps 1-5012-4-US for minimal quantity metering Magnetic piston pump Injection oiler Micropump Grease metering P Metering pumps deliver and meter out lubricants. This piston pumps
More informationDUOFLEX lubrication pumps
DUOFLEX lubrication pumps 1-0012-1-US for dual-line central lubrication systems MS AS FD3 FV50 Applications DUOFLEX grease lubrication pumps are used when a large number of lube points have to be reliably
More informationPiston Distributors, Metering Units
Piston Distributors, Metering Units 1-5001-US For single-line total-loss lubrication systems Group 320 0.01-0.16 ccm Group 321 0.03-0.1 ccm Group 340 0.01-0.16 ccm Group 350 0.1-0.6 ccm Group 390 0.2-1.5
More informationPiston Pumps with Reservoir
Piston Pumps with Reservoir 1-0107-2-US for grease up to NLGI grade 2 with electric drives for progressive and multiline systems KFA1 / KFA10 KFG1-5-W2-M KFGS30-5 Because of their delivery rates and reservoir
More informationVECTOLUB Minimal Quantity Lubrication
VECTOLUB Minimal Quantity Lubrication 1-5012-2-US for tools and dies VECTOLUB 1 VECTOLUB 2 VECTOLUB 3 External minimal quantity lubrication (MQL) VOGEL MQL pays off, because the workpiece and environment
More informationSingle- and Multicircuit Pumps
Single- and Multicircuit Pumps 1-1204-US for Circulating and Hydrostatic Lubrication as Gear, Gerotor and Vane Pump Units, Reservoir Units Gear pump unit Gerotor pump unit Multicircuit pump unit The pump
More informationGVP, chain lubrication
GVP, chain lubrication 1-4101-US Grease injecting lubrication system for moving conveyor chain pins and rollers GVP unit with 2 injectors Application The grease injecting lubrication system GVP has been
More informationGrease lubricating pump FB DSK US (06.02)
Grease lubricating pump FB DSK -005-00 US (06.0) electrically-driven, for medium-sized and large-scale multiline and progressive systems PSG- with plunger detector PSG- with plunger detector VPB with plunger
More informationProgressive Feeders. for progressive grease and oil systems US
Progressive Feeders 1-0107-1- US for progressive grease and oil systems Group: VPB Metering rate [ccm]: 0.2 VPK VP 0.05-0.6 0.1-1.2 SPVS 0.16-0.32 PSG2 PSG3 0.06-0.84 0.8-3.2 Features of progressive systems
More informationSystem description for cylinder lubrication and valve seat lubrication on large 4-stroke diesel engines
for cylinder lubrication and valve seat lubrication on large 4-stroke diesel engines Valve seat lubrication Cylinder lubrication Version 04 Page 2 for cylinder lubrication and valve seat lubrication on
More informationCentralized Lubrication Systems for Commercial Vehicles
Centralized Lubrication Systems for Commercial Vehicles 1-8029-US Product range Less downtime Reduced wear and tear Quality Management DIN EN ISO 9001: 2000 Environmental Management DIN EN ISO 14001 Centralized
More informationSP/SMT 1 Flow Divider
1-5017-EN S/SMT 1 Flow Divider with and without inline strainer for circulating-oil or hydraulic systems Introduction The flow divider splits the supplied flow into two equal induvidual flows or into two
More informationCompact Units for Oil
Compact Units for Oil 1-1203-US Group MKU 0.1, 0.2 or 0.5 l/min MKU1-KW2- MKU2-KW3-20 MKU2-BW3-22 MKU2-KW6-22 These MKU compact units were developed to supply intermittently operated single-line central
More informationPSG product series. Modular feeder. For oil and grease For use in SKF ProFlex progressive and SKF CircOil circulating centralized lubrication systems
odular feeder PSG product series For oil and grease For use in SKF ProFlex progressive and SKF CircOil circulating centralized lubrication systems PSG1 PSG2 PSG3 Fields of application etal-forming machinery
More informationMetering Units and Piston Distributors with Quick Connector System
1-5015-US Metering Units and Piston Distributors with Quick Connector System for single-line total-loss lubrication systems (oil or fluid grease) Group 320: 0.01-0.16 ccm for oil 0.03-0.10 ccm for fluid
More informationFlow Monitors and Sensors
1-1704-EN Flow Monitors and Sensors for intermittent and circulating centralized lubrication systems Flow monitor Flow sensor Oil-streak sensor Flow monitors/sensors have the task of monitoring the flow
More informationPTEX extruder pumps.
PTEX extruder pumps 1-4009-US Pneumatic extruder pump for drum of grease up to NLGI grade 2 Transfer of lubricant to the lubrication installation The PTEX extruder pumps are pneumatically actuated pumps
More informationUD and UC Gear pump unit
1-19-EN for SKF CircOil or hydraulic lubrication systems General Information The UC and UD gear pump units are vertically or horizontally arranged units that are used in hydraulic or circulating-oil lubrication
More informationChain lubrication, accessories
1-106-EN Chain lubrication, accessories Nozzles, oiling brushes, reservoirs and other accessories for chain lubrication Oil projection nozzle AC-A Compact design, pinpoint accuracy, and high temperature
More informationMotor-driven pump unit GSJB
1-4002-1-EN Motor-driven pump unit GSJB Multi-outlet pump units with oil or grease reservoir designed for centralized lubrication systems The motor-driven pump units GSJB have been especially designed
More informationBlock feeder SPVS Used in oil or grease lubrication systems
1-3029-EN Block feeder SPVS Used in oil or grease lubrication systems Block feeders of the SPVS series are used in grease and oil total loss lubrication systems. They are used to either increase the number
More informationLubriLean Minimal Quantity Lubrication
LubriLean Minimal Quantity Lubrication 1-5102-US For customized dry machining processes Digital UFD10 Vario UFV10 Basic UFB10 Smart UFS10 Internal MQL External MQL Internal minimal quantity lubrication
More informationBlock feeder SPVS Used in oil or grease lubrication systems
1-3029-EN Block feeder SPVS Used in oil or grease lubrication systems Block feeders of the SPVS series are used in grease and oil total loss lubrication systems. They are used to either increase the number
More informationSingle-Line Centralized Lubrication Systems
1-15-EN Single-Line Centralized Lubrication Systems For fluid grease, NLGI grades, PFE-15-1. PF-289 MFE2-KW6F-S1 U1 U2 U3 The layout of a single-line centralized lubrication system for grease is largely
More informationBlock metering device VPB. Block feeder for use in oil or grease lubrication systems
Block metering device VPB Block feeder for use in oil or grease lubrication systems Block metering device VPB Block metering devices or feeders of the VPBM/VPBG series are used in small circulating-oil
More informationManually or pneumatically actuated Piston pumps
Manually or pneumatically actuated Piston pumps For oil and fluid grease For use in SKF MonoFlex single-line centralized lubrication systems These manually or pneumatically actuated piston pumps were designed
More informationSKF Grease injection system
1-4101-EN SKF Grease injection system Grease injecting lubrication system type GVP for moving conveyor chain pins and rollers The grease injecting lubrication system GVP has been developed to carry out
More informationChain lubrication, accessories
1-4106-US Chain lubrication, accessories Nozzles, oiling-brushes, reservoirs and other accessories for the chain lubrication Im Folgenden finden Sie Informationen zu einem Teil unseres Leistungs- und Serviceportfolios.
More informationGrease Pump Units For progressive and multiline systems, manually, pneumatically or hydraulically actuated
1-0107-4-EN Grease Pump Units For progressive and multiline systems, manually, pneumatically or hydraulically actuated PF-23-2 PFP-23-2 PFH-23-2 Single- and dual-circuit piston pumps are designed for the
More informationElectric Plug-and-Socket Connectors
-70-EN Electric Plug-and-Socket Connectors Sockets for pressure switches, level switches, flow sensors, directional control valves and filters DIN EN 750-80/ISO 4400 DIN EN 750-804 M Electric plugs or
More informationAccessories for Minimal Quantity Metering
1-5012-5-EN Accessories for Minimal Quantity Metering for chain lubrication and surface wetting Brush Spray head Flow volume divider Nozzles Pinpoint application of metered quantities of oil Brushes Storage
More informationProgressive distributor MX-F
The progressive piston distributors are distributor devices with a hydraulic sequence control, the pistons of which are regulated by the supplied lubricant in a way that the lubricant inevitably and successively
More informationInjection oilers, micro pumps
1-5012-4-EN Injection oilers, micro pumps for minimal quantity metering Injection oiler, 3-port type Injection oiler, 1-port type Micro pump Delivery rates Metering pumps deliver lubricants in a measured
More informationManually or pneumatically actuated piston pumps
Manually or pneumatically actuated piston pumps Product series Pxx For oil and fluid grease For use in SKF MonoFlex single-line centralized lubrication systems Manually or pneumatically actuated piston
More informationCompact Units. For fluid grease, NLGI grades 000, 00 Group MKF 0.1 or 0.2 l/min EN
1-16-EN Compact Units For fluid grease, NLGI grades, Group MKF.1 or.2 l/min MKF1-KW2-2 MKF2-KW3-2 MKF2-KW6-22 These MKFcompact units were developed to supply intermittently operated single-line centralized
More informationGrease Pump Units. For progressive and multiline systems, manually, pneumatically or hydraulically actuated. Please note!
1-0107-4-EN Grease Pump Units For progressive and multiline systems, manually, pneumatically or hydraulically actuated PF-23-2 PFP-23-2 PFH-23-2 Single- and dual-circuit piston pumps are designed for the
More informationInjection oilers, micro pumps for minimal quantity metering
1-5012-4-EN Injection oilers, micro pumps for minimal quantity metering Injection oiler, 3-port type Injection oiler, 1-port type Micro pump Delivery rates Metering pumps deliver lubricants in a measured
More informationPPU, PHU Piston Pumps for progressive grease and oil systems, pneumatically or hydraulically actuated
1-0107-5-EN PPU, PHU Piston Pumps for progressive grease and oil systems, pneumatically or hydraulically actuated These piston pumps are available with two different delivery rate ranges. The pumps can
More informationElectric pump EP-1. Electric pump with 1.9 kg reservoir:
The BEKA-MA central lubrication pump model EP-1 is electrically actuated and has up to a maximum of independently operating lubricant outlets. A separate pump element is required for each outlet. Three
More informationChain lubrication, accessories Nozzles, oiling-brushes, reservoirs and other accessories for the chain lubrication EN
Nozzles, oiling-brushes, reservoirs and other accessories for the chain lubrication 1-106-EN 16 10,5 16 10,5 ~ ~ Chain lubrication, accessories Oil projection nozzle AC-A Compact design, pinpoint accuracy,
More informationFor grease For application in SKF DuoFlex dual-line centralized lubrication systems
Change-over valves, differential pressure switch ccessories for Dual-line Systems For grease For application in SKF DuoFlex dual-line centralized lubrication systems Change-over valves Hydraulical or electrical
More informationProgressive distributor SXE-2
The progressive piston distributors SXE-2 are distribution units with hydraulic sequence control, whose pistons are controlled by the lubricant supply so that the lubricant is forced in sequence through
More informationSystem 6000 Electropneumatic Converter for Direct Current Signals i/p Converter Type 6126
System 6 Electropneumatic Converter for Direct Current Signals i/p Converter Type 66 Application Devices used to convert a direct current signal into a pneumatic signal for measurement and control. Especially
More informationFor high-viscosity oils and fluid grease of NLGI grades 000, 00 For use in SKF MonoFlex single-line centralized lubrication systems
Gear pump unit roduct series KFB For high-viscosity oils and fluid grease of NLGI grades 000, 00 For use in SKF MonoFlex single-line centralized lubrication systems SKF gear pump units of the KFB product
More information3/2-way Solenoid Valve for pneumatics
656 3/-way Solenoid Valve for pneumatics Compact design Single and manifold mounting Low power consumption Rocker pilot in DC Type 656 can be combined with... Fast response times Type 506 Type 510/511
More informationSKF VectoLub, accessories Accessories for the minimal quantity lubrication systems VTEC and VE1B EN
SKF VectoLub, accessories Accessories for the minimal quantity lubrication systems VTEC and VE1B 1-4402-EN Spray blocks Every spraying unit is connected to the coaxial outlet of a VTEC or VE1B unit. It
More informationGrease Lubrication Pump FK
1-3033-EN 1-0358-US for use in progressive, single-line and dual-line centralized lubrication systems pplication he FK pump unit is a multi-function piston pump whose modular structure makes it very versatile.
More informationSKF VectoLub, VE1B units
1-4403-EN SKF VectoLub, VE1B units External minimal quantity lubrication, Volumetric metering The emql system SKF VectoLub is a clean and economical alternative for lubricant projection in minimal quantity.
More informationJM Oil Lubrication Pump SKF MultiFlex multi-line pump units for total loss oil lubrication systems on compressors
1-3007-EN SKF MultiFlex multi-line pump units for total loss oil lubrication systems on compressors General Information The JM oil lubrication pump is a highpressure multiline pump that produces a maximum
More informationDG 060 DG 061 DG 062 DG 063 DG 064 for Pressure and High Pressure Filters Operating pressure up to 600 bar Response/switching pressure up to 5,0 bar
Clogging Indicators DG 060 DG 061 DG 062 DG 063 DG 064 for Pressure and High Pressure Filters Operating pressure up to 600 bar Response/switching pressure up to 5,0 bar Description Application Monitoring
More informationTable of contents. Table of contents. Overview of progressive distributor Distributor bridge without outlet...
Table of contents 4 Technical basics System description... 04-0-10-01 Construction, applications, advantages, function System design... 04-0-10-02 Design and installation of progressive systems Calculation
More informationElectric Immersion Pumps PXA and PXK, sealless
1-6062-US PXA and PXK, sealless MQUALITY MANAE ENT Cooling and lubricating with high-pressure... Centrifugal pumps for delivery pressures up to 25 bars Technical data Delivery rate Q max = 185 l/min Delivery
More informationElectropneumatic Converters i/p Converters Type 6111 Mounting and Operating Instructions EB 6111 EN
Electropneumatic Converters i/p Converters Type 6111 Fig. 1 Type 6111 in standard version Fig. Type 6111 mounted on a supply air manifold Fig. 3 Type 6111 in field enclosure Mounting and Operating Instructions
More informationHydraulic pump HP-1. Type 1. Type 2
The BEKA-MAX central lubrication pump model HP-1 is hydraulic actuated and has up to a maximum of independently operating lubricant outlets. A separate pump unit is required for each outlet. Three pump
More informationDG 023 DG 024 DG 025 DG 041 DG 042. Clogging Indicators
Clogging Indicators DG 03 DG 04 DG 05 DG 041 DG 04 For Pressure and High Pressure Filters Operating pressure up to 657 psi Response/Switching pressure up to 73 psi 60.30-4us Description Application Monitoring
More informationEUGEN WOERNER GmbH & Co. KG Postfach 1661 DE Wertheim Hafenstrasse 2 DE Wertheim. Progressive distributor VPB
Progressive distributor VPB Use: In progressive mode based central lubrication systems. The main features of WOERNER progressive distributors are as follows: Accurate proportioning volumes. different proportioning
More informationEUGEN WOERNER GmbH & Co. KG Postfach 1661 D Wertheim Am Eichamt 8 D Wertheim
Progressive distributor in element construction VPI-D Use: In progressive mode based central lubrication systems. The main features of WOERNER progressive distributors are as follows: 4 different proportioning
More informationEUGEN WOERNER GmbH & Co. KG Postfach 1661 DE Wertheim Hafenstrasse 2 DE Wertheim. Progressive distributor VPA-D
Progressive distributor VPA-D Use: In progressive mode based central lubrication systems. The main features of WOERNER progressive distributors are as follows: Accurate proportioning volumes. Clear and
More informationInexpensive solution for the lubrication of linear guides and rolling bearings
1-0988-EN Compact Greaser Inexpensive solution for the lubrication of linear guides and rolling bearings Compact Greaser Up to 5 lubricant outlet ports 3 different metered volumes (15 mm 3 standard) Suitable
More informationClogging Indicators. Description. Page 393. Application Monitoring the contamination of pressure and high pressure filters.
Clogging Indicators DG 023 DG 024 DG 041 DG 042 for Pressure and High Pressure Filters Operating pressure up to 450 bar / 5627 psi Response / switching pressure up to 5.0 bar / 73 psi Description pplication
More informationStandard filter Disk filter Return filter. Lubrication systems can fail from the following
Filters For oil For use in SKF centralized lubrication systems Standard filter Disk filter Return filter Why filtering? Solids are diagnosed to be the main cause of damages on the components that are used
More informationStandard filter Disk filter Return filter. Lubrication systems can fail from the following
Filters For oil For use in SKF centralized lubrication systems Standard filter Disk filter Return filter Why filtering? Solids are diagnosed to be the main cause of damages on the components that are used
More informationProduct series DSA, DSB, DSC, DSD
Pressure Switches Product series DSA, DSB, DSC, DSD For oil, fluid grease and grease For use in SKF centralized lubrication systems, hydraulic and compressed-air systems DSA DSB DSC SKF pressure switches
More informationVHS... Screw Flow Meter
Member of the Group VHS... Screw Flow Meter The normal transmitter with block plug already has a push pull output to serve all NPN or PNP Inputs. It supplies a square wave signal. Those transducers are
More informationVersions. Version with K VS Version with K VS 2.0. Fig. 1: Type 3967 Solenoid Valve
Type 367 Solenoid Valve Application Solenoid valve for controlling pneumatic linear actuators with NAMUR rib according to IEC 60534 or pneumatic rotary actuators with NAMUR interface according to VDI/VDE
More informationProgressive Central Lubrication System
Progressive Central Lubrication System APPLICATION Centralized lubrication systems with progressive distributors preferably serve the lubrication of machinery. The lubrication capacity is up to approx.
More informationAirLINE and AirLINE Quick electrical/pneumatic Automation System
AirLINE and AirLINE Quick electrical/pneumatic Automation System Type 8644 can be combined with Fully compatible with Rockwell Combination of Fieldbus, pilot valves and I/O modules higher fl exibility
More informationEUGEN WOERNER GmbH & Co. KG Postfach 1661 DE Wertheim Hafenstrasse 2 DE Wertheim. Volume flow meter with throttle- and bypass valve KUZ-L
with throttle- and bypass valve Use: In oil lubrication systems H Viscosity-independent volume flow monitoring High measuring accuracy ig monitoring range Continuously adjustable volume flow Gearwheels
More informationSuction Filter Pi 160
Suction Filter Pi 160 1. Features High performance filters for modern hydraulic systems _ Provided for tank mounting Compact design Minimal pressure drop through optimal flow design Visual/electrical/electronic
More informationMounting and Operating Instructions EB 5868/5869 EN
Electric Control Valves Types 3213/5857, 3213/5824, Types 3214/5824, 3214/3374, 3214/3274 with safety function: Types 3213/5825, 3214/5825, 3214/3374, 3214/3274 Pneumatic Control Valves Types 3213/2780-1,
More informationSOLENOID VALVES FOR REFRIGERATING SYSTEMS
SOLENOID VALVES 17 SOLENOID VALVES FOR REFRIGERATING SYSTEMS APPLICATIONS The solenoid valves, shown in this chapter, are classified Pressure accessories in the sense of the Pressure Equipment Directive
More informationlubrication systems PEGPEO 5N-10N-25N-210N pumps for progressive systems
lubrication systems PEGPEO 5N-10N-25N-210N pumps for progressive systems TABLE OF CONTENTS TABLE OF CONTENTS 2 Applications and operation 3 Technical data Operation 4 Tank 4 PEG-PEO 5N/10N/SM Electric
More informationChapter 5: Flow Valves
Catalogue HY11-300/UK Contents Chapter : Flow Valves Series Description Size Mounting Page Parker Standard DIN / ISO 1/4 3/8 1/2 3/4 1 06 10 16 Throttle valves, manual adjustment MVI -2 NS -4 FS With free
More informationDirect-acting 3/2 way plunger valve
Direct-acting 3/2 way plunger valve Direct-acting, compact valve with diameter of up to DN 2.5 Vibration-proof, bolted coil system Banjo threaded connection for direct mounting on pneumatic valves Type
More informationMWR Reamer 08/01/2010
MWR Reamer 08/01/2010 Operating Instructions and Spare Parts List Torch Nozzle Cleaning Device for Robotic Mig Welding System Registration Purchaser: Address; City State Zip Phone: Email: Contact: Purchased
More informationT 3965 EN Type 3965 Solenoid Valve Island To control pneumatic actuators
T 365 EN Type 365 Solenoid Valve Island To control pneumatic actuators Application The Type 365 Solenoid Valve Island is a compact solution for the central control of pneumatic actuators in chemical and
More informationTransmitters: Relay Valve VR4151/4152
Relay Valve VR4151/4152 Appropriate output sequences are affected according to the signal received from the mechanical valve. VR4151 VR4152 Precautions Be sure to read before handling. Refer to pages 5-11-2
More informationConnection Ports: 3/4 1 1/4 BSP (other thread options on request)
HYDRAULIC FILTRATION Medium pressure, in line spin-on filters Technical Information Pressure: Max working (acc. to NFPA T 3.10.17): FA-4-1x: 34,5 bar (500 psi) FA-4-21: 24 bar (348 psi) Burst (acc. to
More informationFiltrec elements are tested according to ISO 2941, ISO 2942 and ISO 23181
Common HYDRAULIC FILTRATION Side wall mounting suction filters Technical Information Connection Ports: 1-1 1/4-1 1/2 BSP (other thread options on request) 1 1/2 SAE J518-3000/M12 Housing Materials: Cover:
More informationDirectional Valves for oil or grease
1-173-EN Directional Valves for oil or grease 161-1-31 161-1-5 DV5-4 Function he directional valves listed on the following pages are used to control the flow of lubricants, e.g. to divide up a central
More informationANSI version. The valve closes when the differential pressure rises
Self-operated Regulators Series 42 Differential Pressure Regulator with Type 2424/Type 2428 Actuator and Type 2422 Valve Type 42-24 A Type 42-24 B Type 42-28 A Type 42-28 B ANSI version Application For
More informationINLINE Flow sensor for hazardous area II 1 G/D - II 2 D - II 3 GD - I M1
INLINE Flow sensor for hazardous area II G/D - II D - II GD - I M Type SE0 Ex can be combined with... Flow meter with NAMUR or NPN/PNP output signal Mounting, dismounting of electronics by a Quarter-Turn
More informationSeated valve bidirectional Type WVM-4B-Bi
Seated valve bidirectional Type WVM-4B-Bi Features Bidirectional (flow of fluid in both directions, independently of pressure prof) Low pressure drop Direct operated Leakage free Good resistance to corrosion
More informationAUTHORIZED DISTRIBUTOR DPX PROGRESSIVE DIVIDERS
1 DESCRIPTION Ilcolube is the lubrication system which identifies distribution and dosing with a progressive movement of pistons that are. Controlled one by the other in an interdependent sequence. This
More informationModular pneumatic valve unit
Modular pneumatic valve unit Compact design Modular configuration High flexibility Type 8640 can be combined with Simple exchange of valves (with option P-shut-off - also possible during operation) Type
More informationBlock mounting filter, lateral flange-mounting possible
Block mounting filter, lateral flange-mounting possible RE 0/.0 Replaces: 0.09 / Types 0/0 FEN 000 to 000; 0/0 FE 000, 00, 008 Nominal sizes according to DIN 0: 000 to 000 Nominal sizes according to BRFS:
More informationINSTRUCTION MANUAL. I/P Converter DSG BXXY3Z DSG BXXY4Z
INSTRUCTION MANUAL I/P Converter DSG BXXY3Z DSG BXXY4Z Revision 2.0 3.626 016136 en Page 1/15 Should you have any questions concerning the I/P converter, please contact the Service Department of the Product
More informationSOLENOID VALVES FOR REFRIGERATING SYSTEMS
SOLENOID VALVES 17 SOLENOID VALVES FO EFIGEATING SYSTEMS APPLICATIONS The solenoid valves, shown in this chapter, are classified Pressure accessories in the sense of the Pressure Equipment Directive 97/23/EC,
More informationEUGEN WOERNER GmbH & Co. KG Postfach 1661 DE Wertheim Am Eichamt 8 DE Wertheim. Progressive distributor VPA-B
Progressive distributor VPA-B Use: In progressive mode based central lubrication systems. The main features of WOERNER- progressive distributors are as follows: Accurate proportioning volumes. Clear and
More informationEB EN. Type 3372 Electropneumatic Actuator. Translation of original instructions
EB 8313-1 EN Translation of original instructions V2001-IP Control Valve Type 3372 0511/0531 Electropneumatic Actuator with Type 3321 Valve Type 3372 Electropneumatic Actuator Edition July 2013 Note on
More informationElster RABO. Connected Industrial. Highly Accurate Rotary Gas Meter FEATURES & BENEFITS. Applications. Brief information
Connected Industrial Elster RABO Highly Accurate Rotary Gas Meter Applications Honeywell Elster has combined tried and tested product features of their RPM and IRM rotary meter product lines with new developments
More informationLevel indicators, screw plugs
Level indicators, screw plugs 885 Product overview Level indicators, screw plugs Oil level gauges K0443 Plastic plugs K0452 Oil level gauges K0444 Page 888 Aluminium plugs K0453 Page 894 Oil level sight
More informationRemote Process Actuation Control System AirLINE - Rockwell 1734 Point I/O System
Remote Process Actuation Control System AirLINE - Rockwell 1734 Type 8644 can be combined with... Fully compatible with Rockwell 1734 Point I/O System Combination of Fieldbus, pilot valves and I/O modules
More informationRemote Process Actuation Control System AirLINE - Siemens ET 200S
Remote Process Actuation Control System AirLINE - Siemens ET 200S Type 8644 can be combined with... Fully compatible with Siemens ET 200S Combination of Fieldbus, pilot valves and I/O modules High flexibility
More information