ADJUSTABE PITCH SERIES FEATURES: Stock Sizes - 1 and 2 grooves up to 25 HP Both 1 and 2 groove adjustable sheaves permit variations of as much as 30% in speed when used with a fixed diameter sheave Available in metric bores arger sizes come with 2 set screws Other special bores are available, call for delivery terms NOTE: Applications with a speed superior to 5000 ft./ min. may require more accurate balancing. Specify sheave and required bore diameter when ordering. EXAMPE: 8600X1-3/8 8600 8600: 1-3/8: X 1-3/8 ADJUSTABE PITCH SHEAVE SIZE The first digit stands for 8000 series. ast three digits represent the approximate outside diameter (6.00) BORE SIZE (1-3/8") Bore size: Metric bore sizes are de signated with MM after the metric dimension (X 25MM). Inch bore sizes are de signated with the whole inch followed by the fraction. For example, a 1.5" diameter bore would be 1-1/2. Pulley Adjustment Modify the sheave pitch diameter by rotating the adjustable flange on the threaded hub of the pulley. Once the required diameter is obtained, tighten the adjusting screw(s) on one of the two flat surfaces. To obtain the same pitch diameter in both grooves of the D8000 series, tighten both movable flanges against the central flange, make trace marks on both flanges, then rotate both flanges the same number of turns. HOW TO ORDER
ADJUSTABE PITCH SERIES 1 GROOVE 2 GROOVES 1 GROOVE Part No. Cross. Ref. 1 F Max. Min. Max. Min. G Available Stock Bores Weight (lbs) 8325 1VP34 3.25 1-3/4 1-1/32 21/32 3/4 3/8 9mm 14mm 19mm 2.0 8350 1VP40 3.75 1-3/4 1-5/32 25/32 7/8 1/2 9mm 14mm 19mm 24mm 28mm 2.0 8400 1VP44 4.15 1-3/4 1-5/32 25/32 7/8 1/2 12.7mm 14mm 19mm 24mm 28mm 2.5 8450 1 1VP50 4.75 1-3/4 1-5/32 25/32 7/8 1/2 12.7mm 14mm 19mm 24mm 28mm 3.1 8550 2 1VP56 5.35 1-3/4 1-9/32 25/32 1 1/2 1-3/8 1-5/8 12.7mm 14mm 19mm 24mm 28mm 38mm 4.5 8600 2 1VP60/1VP62/1VP65 6.00 1-3/4 1-9/32 25/32 1 1/2 8670 2 1VP68/1VP71 6.70 1-3/4 1-9/32 25/32 1 1/2 5/8 3/4 7/8 1 1-1/8 1-3/8 1-5/8 12.7mm 19mm 24mm 28mm 38mm 42mm 5/8 3/4 7/8-1 1-1/8 1-3/8 1-5/8 12.7mm 19mm 24mm 28mm 38mm 42mm 5.0 6.0 8740 2 1VP75 7.40 1-3/4 1-9/32 25/32 1 1/2 3/4 7/8 1 1-1/8 1-3/8 1-5/8 24mm 28mm 38mm 42mm 7.0 * Supplied without keyway 1 Comes with two set screws at 120 degrees 2 Comes with two set screws at 120 degrees and an H Key U.S. Patent Nº 450 4249 Can. Patent Nº 1160478
ADJUSTABE PITCH SERIES DATUM DIAMETERS Datum Diameter, Inches Part No. Min. Max. 0 Turn Close 1 Turn 2 Turns 3 Turns 4 Turns 5 Turns 6 Turns (4) A (5) B 5V 8325 2.30 3.10-3.10 2.90 2.70 2.50 2.30 8350 2.40 3.40 3.40 3.20 3.00 2.80 2.60 2.40 8400 2.80 3.80 3.80 3.60 3.40 3.20 3.00 2.80 8450 3.40 4.40 4.40 4.20 4.00 3.80 3.60 3.40 8550 3.95 5.03 5.03 4.76 4.49 4.22 3.95 8600 4.33 5.68 5.68 5.41 5.14 4.87 4.60 4.33 8670 5.03 6.38 6.38 6.11 5.84 5.57 5.30 5.03 8740 5.73 7.08 7.08 6.81 6.54 6.27 6.00 5.73 8325 2.50 3.10-3.10 2.90 2.70 2.50 8350 2.70 3.70-3.70 3.50 3.30 3.10 2.90 2.70 8400 3.10 4.10-4.10 3.90 3.70 3.50 3.30 3.10 8450 3.70 4.70-4.70 4.50 4.30 4.10 3.90 3.70 8550 3.80 5.15-5.15 4.88 4.61 4.34 4.07 3.80 8600 4.45 5.80-5.80 5.53 5.26 4.99 4.72 4.45 8670 5.15 6.50-6.50 6.23 5.96 5.69 5.42 5.15 8740 5.85 7.20-7.20 6.93 6.66 6.39 6.12 5,85 8325 - - - - -- 8350 - - - - -- 8400 - - - - -- 8450 - - - - -- 8550 4.17 5.25-5.25 4.98 4.71 4.44 4.17 8600 4.55 5.90-5.90 5.63 5.36 5.09 4.82 4.55 8670 5.25 6.60-6.60 6.33 6.06 5.79 5.52 5.25 8740 5.95 7.30-7.30 7.03 6.76 6.49 6.22 5.95 P.D. for A belts = Datum Dia. A belts +.25" P.D. for B belts = Datum Dia. B belts +.35" P.D. for 5V belts = Datum Dia. 5V belt +.10"
ADJUSTABE PITCH VP SERIES VP SERIES FEATURES: 1VP and 2VP Series are finished bore variable speed sheaves made of cast iron and designed for heavier duty service up to 25HP Available in single and double grooves, they offer a pitch range from 1.9" to 6.7" (A belt) and 2.4" to 7.0" (B belt) Type 2 model has positive locked-on settings HOW TO ORDER EXAMPE: 1VP71X3/4 1 VP71 X 3/4 1: NUMBER OF GROOVES VP71: ADJUSTABE PITCH SHEAVE SIZE ast 2 digits represent the approximate outside diameter (7.1") 3/4: BORE SIZE (3/4") Bore size: Inch bore sizes are designated with the whole inch followed by the fraction. For example, a 1.5" diameter bore would be 1-1/2. Pulley Adjustment Modify the sheave pitch diameter by rotating the adjustable flange on the threaded hub of the pulley. Once the required diameter is obtained, tighten the adjusting screw(s) on one of the two flat surfaces. To obtain the same pitch diameter in both grooves of the VP series, tighten both movable flanges against the central flange, make trace marks on both flanges, then rotate both flanges the same number of turns.
1VP & 2VP SERIES ADJUSTABE PITCH VP SERIES TYPE 1 (without key) TYPE 2 TYPE 3 (without key) TYPE 4 Part No. Type F Max. Min. Max. Min. G Available Stock Bores Weight (lbs) 1VP25 1 2.50 1-1/2 13/16 9/16 5/8 3/8 *1/2 7 1VP30 1 2.87 1-21/32 13/16 9/16 5/8 3/8 *1/2 5/8 3/4 1.1 1VP34 1 3.15 1-7/8 1 11/16 13/16 1/2 *1/2 5/8 3/4 7/8 1.4 1VP40 1 3.75 1-7/8 1-1/16 11/16 7/8 1/2 *1/2 5/8 3/4 7/8 1.9 1VP44 1 4.15 1-7/8 1-1/16 11/16 7/8 1/2 *1/2 5/8 3/4 2.4 1VP44 2 4.15 1-7/8 1-1/8 3/4 7/8 1/2 7/8 1 1 1/8 2.9 1VP50 1 4.75 2 1-1/16 11/16 7/8 1/2 *1/2 5/8 3/4 2.9 1VP50 2 4.75 1-7/8 1-1/8 3/4-7/8 1/2 7/8 1 1-1/8 3.6 1VP56 1 5.35 1-7/8 1-1/16 11/16 7/8 1/2 *1/2 5/8 3/4 3.8 1VP56 2 5.35 1-7/8 1-1/8 3/4 7/8 1/2 7/8 1 1-1/8 4.4 1VP60 2 6.00 1-21/32 1-1/4 7/8 1-1/32 21/32 3/4 7/8 1-1/8 1-3/8 6.5 1VP62 2 5.95 1-29/32 1-1/8 3/4 7/8 1/2 5/8 3/4 7/8 1 1-1/8 1-1/4 1-3/8 6.1 1VP65 2 6.50 1-21/32 1-1/4 7/8 1-1/32 21/32 3/4 7/8 1-1/8 1-3/8 1-5/8 6.8 1VP68 2 6.55 1-29/32 1-1/8 3/4 7/8 1/2 5/8 3/4 7/8 1 1-1/8 1-1/4 1-3/8 7.3 1VP71 2 7.10 1-21/32 1-1/4 7/8 1-1/32 21/32 3/4 7/8 1-1/8 1-3/8 1-5/8 8.2 1VP75 2 7.50 1-21/32 1-1/4 7/8 1-1/32 21/32 3/4 7/8 1-1/8 1-3/8 9.2 2VP36 3 3.35 3 2 1-3/8 13/16 1/2 *1/2 5/8 3/4 7/8 1 3.4 2VP42 3 3.95 3 2-1/8 1-3/8 7/8 1/2 5/8 3/4 7/8 1 1-1/8 4.4 2VP50 4 4.75 3 2-1/8 1-3/8 7/8 1/2 5/8 3/4 7/8 1 1-1/8 6.3 2VP56 4 5.35 3 2-1/8 1-3/8 7/8 1/2 5/8 3/4 7/8 1 1-1/8 7.8 2VP60 4 6.00 3-1/4 2-3/8 1-5/8 1-1/32 21/32 3/4 7/8 1-1/8 1-3/8 1-5/8 10.6 2VP62 4 5.95 3 2-1/8 1-3/8 7/8 1/2 3/4 7/8 1 1-1/8 1-1/4 1-3/8 10.0 2VP65 4 6.50 3-1/4 2-3/8 1-5/8 1-1/32 21/32 3/4 7/8 1-1/8 1-3/8 1-5/8 12.3 2VP68 4 6.55 3 2-1/8 1-3/8 7/8 1/2 7/8 1 1-1/8 1-1/4 1-3/8 1-5/8 1-7/8 11.7 2VP71 4 7.10 3-1/4 2-3/8 1-5/8 1-1/32 21/32 3/4 7/8 1-1/8 1-3/8 1-5/8 1-7/8 50MM 14.6 2VP75 4 7.50 3-1/4 2-3/8 1-5/8 1-1/32 21/32 3/4 7/8 1-1/8 1-3/8 1-5/8 1-7/8 16.5 * Supplied without keyway thru the bore
ADJUSTABE PITCH VP SERIES DATUM DIAMETERS 3 (4) A (5) B 5V Part No. Min. Max. 0 Turn Close P.D. for 3 belts = Datum Dia. 3 belts +.25" P.D. for "A (4) belts = Datum Dia. A belts +.25" 1 Turn Datum Diameter, Inches 2 Turns 3 Turns 4 Turns 5 Turns 1VP25 1.6 2.4 2.4 2.2 2.0 1.8 1.6 - - 1VP30 1.8 2.6 2.6 2.4 2.2 2.0 1.8 - - 1VP34 1.7 2.5 2.5 2.3 2.1 1.9 1.7 - - 2VP36 1.9 2.7 2.7 2.5 2.3 2.1 1.9 - - 1VP40 2.3 3.1 3.1 2.9 2.7 2.5 2.3 - - 2VP42 2.5 3.3 3.3 3.1 2.9 2.7 2.5 - - 1VP44 2.7 3.5 3.5 3.3 3.1 2.9 2.7 - - 1VP50 & 2VP50 3.3 4.1 4.1 3.9 3.7 3.5 3.3 - - 1VP56 & 2VP56 3.9 4.7 4.7 4.5 4.3 4.1 3.9 - - 1VP60 & 2VP60 - - - - - - - - - 1VP62 & 2VP62 4.5 5.3 5.3 5.1 4.9 4.7 4.5 - - 1VP65 & 2VP65 - - - - - - - - - 1VP68 & 2VP68 5.1 5.9 5.9 5.7 5.5 5.3 5.1 - - 1VP71 & 2VP71 - - - - - - - - - 1VP75 & 2VP75 - - - - - - - - - 1VP34 1.9 2.9 2.9 2.7 2.5 2.3 2.1 1.9-2VP36 2.0 3.0 3.0 2.8 2.6 2.4 2.2 2.0-1VP40 2.4 3.4 3.4 3.2 3.0 2.8 2.6 2.4-2VP42 2.6 3.6 3.6 3.4 3.2 3.0 2.8 2.6-1VP44 2.8 3.8 3.8 3.6 3.4 3.2 3.0 2.8-1VP50 & 2VP50 3.4 4.4 4.4 4.2 4.0 3.8 3.6 3.4-1VP56 & 2VP56 4.0 5.0 5.0 4.8 4.6 4.4 4.2 4.0-1VP60 & 2VP60 4.2 5.2 5.2 5.0 4.8 4.6 4.4 4.2-1VP62 & 2VP62 4.6 5.6 5.6 5.4 5.2 5.0 4.8 4.6-1VP65 & 2VP65 4.7 5.7 5.7 5.5 5.3 5.1 4.9 4.7-1VP68 & VP68 5.2 6.2 6.2 6.0 5.8 5.6 5.4 5.2-1VP71& 2VP71 5.3 6.3 6.3 6.1 5.9 5.7 5.5 5.3-1VP75 & 2VP75 5.7 6.7 6.7 6.5 6.3 6.1 5.9 5.7-1VP342.4 3.2-3.2 3.0 2.8 2.6 2.4-2VP36 2.5 3.3-3.3 3.1 2.9 2.7 2.5-1VP40 2.7 3.7-3.7 3.5 3.3 3.1 2.9 2.7 2VP42 2.9 3.9-3.9 3.7 3.5 3.3 3.1 2.9 1VP44 3.1 4.1-4.1 3.9 3.7 3.5 3.3 3.1 1VP50 & 2VP50 3.7 4.7-4.7 4.5 4.3 4.1 3.9 3.7 1VP56 & 2VP56 4.3 5.3-5.3 5.1 4.9 4.7 4.5 4.3 1VP60 & 2VP60 4.3 5.5 5.5 5.3 5.1 4.9 4.7 4.5 4.3 1VP62 & 2VP62 4.9 5.9-5.9 5.7 5.5 5.3 5.1 4.9 1VP65 & 2VP65 4.8 6.0 6.0 5.8 5.6 5.4 5.2 5.0 4.8 1VP68 & 2VP68 5.5 6.5-6.5 6.3 6.1 5.9 5.7 5.5 1VP71 & 2VP71 5.4 6.6 6.6 6.4 6.2 6.0 5.8 5.6 5.4 1VP75 & 2VP75 5.8 7.0 7.0 6.8 6.6 6.4 6.2 6.0 5.8 1VP34 - - - - - - - - - 2VP36 - - - - - - - - - 1VP40 - - - - - - - - - 2VP42 - - - - - - - - - 1VP44 - - - - - - - - - 1VP50 & 2VP50 - - - - - - - - - 1VP56 & 2VP56 - - - - - - - - - 1VP60 & 2VP60 - - - - - - - - - 1VP62 & 2VP62 5.3 6.3-6.3 6.1 5.9 5.7 5.5 5.3 1VP65 & 2VP65 5.2 6.4 6.4 6.2 6.0 5.8 5.6 5.4 5.2 1VP68 & 2VP68 5.9 6.9-6.9 6.7 6.5 6.3 6.1 5.9 1VP71 & 2VP71 5.8 7.0 7.0 6.8 6.6 6.4 6.2 6.0 5.8 1VP75 & 2VP75 6.2 7.4 7.4 7.2 7.0 6.8 6.6 6.4 6.2 P.D. for B (5) belts = Datum Dia. B belts +.35" P.D. for 5V belts = Datum Dia. 5V belts +.10" 6 Turns