SCOPE OF ACCREDITATION TO ISO/IEC 17025:2005 TUV SUD CANADA INC. 1229 Ringwell Drive Newmarket, Ontario, Canada, L3Y 8T8 William (Mac) Elliott Phone: 813 284 2736 melliott@tuvam.com www.tuv-sud.ca ELECTRICAL Valid To: June 30, 2019 Certificate Number: 2955.08 In recognition of the successful completion of the A2LA evaluation process, accreditation is granted to this laboratory to perform the following types of tests: I. Measurements and Data Acquisition: Test Parameter: Parameter Range: Test Method: Environmental Exposure: Current ± 3000 ADC EMCN_P_10.38 Voltage ± 1000 VDC EMCN_P_10.37 This laboratory also uses customer supplied specifications and/or methods directly related to the testing technologies and parameters listed above. Test: Test Technology: Test Method(s) / Specifications 1 : Battery Abuse Battery UN Shipping, T.1 Altitude UN ST/SG/AC.10/11, Section 38.3.4.1 Battery UN Shipping, T.2 Thermal UN ST/SG/AC.10/11, Section 38.3.4.2 Battery UN Shipping, T.3 Vibration UN ST/SG/AC.10/11, Section 38.3.4.3 Battery UN Shipping, T.4 Shock UN ST/SG/AC.10/11, Section 38.3.4.4 (up to 50G) Battery UN Shipping, T.5 External UN ST/SG/AC.10/11, Section 38.3.4.5 Short Circuit Battery UN Shipping, T.6 UN ST/SG/AC.10/11, Section 38.3.4.6 Impact/Crush Battery UN Shipping, T.7 Overcharge UN ST/SG/AC.10/11, Section 38.3.4.7 Battery UN Shipping, T.8 Forced Discharge UN ST/SG/AC.10/11, Section 38.3.4.8 (A2LA Cert. No. 2955.08) 09/12/2017 Page 1 of 5
Battery Abuse (Cont.) Battery Life Cycle & Performance Battery Abuse Test, Over-charge SAE-J2464, Section 4.5.2 SAND99-0497, Section 4.3 SAND2005-3123, Section 5.1 Battery Abuse Test, Over Discharge SAE-J2464, Section 4.5.3 SAND99-0497, Section 4.4 SAND2005-3123, Section 5.3 Battery Abuse Test, Crush SAE-J2464, Section 4.5.6 SAND99-0497, Section 2.6 SAND2005-3123, Section 3.1 Battery Abuse Test, Penetration SAE-J2464, Section 4.3.3 SAND99-0497, Section 2.3 SAND2005-3123, Section 3.2 Battery Abuse Test, Partial Short SAND99-0497, Section 4.2 Circuit SAND2005-3123, Section 5.4 Battery Abuse Cycling Without Thermal Management SAE J2464, Section 4.4.3 SAND2005-3123, Section 4.4 SAND99-0497, Section 3.4 Battery Abuse Thermal Stability SAE J2464, Section 4.4.2 SAND2005-3123, Section 4.1 SAND99-0497, Section 3.2 Battery Abuse Passive Propagation SAE J2464, Section 4.4.5 Battery Abuse Separator Shutdown SAE J2464, Section 4.5.4 INL/EXT-07-12536, Section 3.12 Battery Abuse Thermal Shock SAE J2464, Section 4.4.4 SAND99-0497, Section 3.5 SAND2005-3123, Section 4.5 Battery Abuse Drop SAE J2464, Section 4.3.2 Battery Reference Performance INL/EXT-07 12536, Section 3.12 Battery Reference Capacity Check MBH (Mercedes Benz Hybrid LLC) Reference Capacity Check Test Instructions (Revision: July 16, 2009) Battery P & C, Hybrid Pulse Power INL/EXT-07 12536, Section 3.4 Characterization (Battery Test Manual for Plug-In Hybrid Electric Vehicles) Battery P&C, Static Capacity INL/EXT-07 12536, Section 3.2 (Battery Test Manual for Plug-In Hybrid Electric Vehicles) Battery P&C, Constant Power Discharge INL/EXT-07 12536, Section 3.3 (Battery Test Manual for Plug-In Hybrid Electric Vehicles) Battery Durability, Calendar INL/EXT-07 12536, Section 4.10 Battery Durability, Cyclic INEEL/EXT-04 01986, Section 3 INL/EXT-07 12536, Section 4.9 (A2LA Cert. No. 2955.08) 09/12/2017 Page 2 of 5
Battery Life Cycle & Performance (Cont.) Battery (General) Battery Durability, CD Mode INEEL/EXT-04 01986, Section 3, Pages 22-31 INL/EXT-07 12536, Section 4.9 Battery Durability, CS Mode INEEL/EXT-04 01986, Section 3, Pages 22-31 INL/EXT-07 12536, Section 4.9 Battery Cold Crank Test INEEL/EXT-04 01986, Section 3 INL/EXT-07 12536, Section 4.5 Battery Electrochemical Impedance INEEL/EXT-04 01986, Section 4.1.9 Spectroscopy (EIS) Battery 1 khz Impedance INEEL/EXT-04 01986, Section 3.1.3.5 Battery ISO Check FMVSS 305 ISO 6469-1, Section 6.1.3 UL Standard for Safety Electric Vehicle UL 2202 (EV) Charging System Equipment Safety Requirements for Portable Sealed Secondary Cells, and for Batteries Made from Them, for use in Portable Applications Safety Requirements for Portable Sealed Secondary Cells, and for Batteries Made from them, for use in Portable Applications Safety of Primary and Secondary Lithium Cells and Batteries during Transport UL 62133; IEC 62133 CAN/CSA E62133 IEC 62281 Primary Batteries -- Part 1: General IEC 60086-1 Primary Batteries Part 2: Physical and electrical specifications Primary Batteries -- Part 3: Watch Batteries Primary Batteries Part 4: Safety of Lithium Batteries Primary Batteries Part 5: Safety of Batteries with Aqueous Electrolyte UL Standard for Safety Lithium Batteries UL Standard for Safety Household and Commercial Batteries UL Standard for Safety Lithium Ion Battery Systems for Use in Electric Power Tool and Motor Operated, Heating and Lighting Appliances General Requirements for Battery- Powered Appliances IEC 60086-2 IEC 60086-3 IEC 60086-4 IEC 60086-5 UL 1642 UL 2054 UL 2575 UL 2595/CSA C22.2 #0.23 (A2LA Cert. No. 2955.08) 09/12/2017 Page 3 of 5
HVAC (Fuel Appliances Testing) Gas-fired low pressure steam and hot ANSI Z21.13 water boilers Gas-fired low pressure steam and hot CSA 4.9 water boilers Standard for gas unit heaters, ANSI Z83.8 gas-packaged heaters, gas utility heaters, and gas-fired duct furnaces Standard for gas unit heaters, CSA 2.6 gas-packaged heaters, gas utility heaters, and gas-fired duct furnaces Gas-fired water heaters, volume III, ANSI Z21.10.3 storage water heaters with input ratings above 75,000 BTU per hour, circulating and instantaneous Gas-fired water heaters, volume III, CSA 4.3 storage water heaters with input ratings above 75,000 BTU per hour, circulating and instantaneous UL Standard for Safety Oil-Fired UL 726 Boiler Assemblies UL Standard for Safety Oil-Fired UL 727 Central Furnaces UL Standard for Safety Oil-Fired UL 729 Floor Furnaces UL Standard for Safety Commercial- UL 795 Industrial Gas Heating Equipment Heating and Cooling Equipment UL 1995/CSA C22.2 No. 236 Oil-Burning Equipment: General Requirements - Third Edition Vaporizing-type oil burners First Edition Atomizing-type oil burners Third Edition Oil burning stoves and water heaters First Edition Oil-fired warm air furnaces Third Edition; Update No. 1: February 2006; Update No. 2: July 2007 Oil-burning equipment: Steam and hot-water boilers Second Edition Portable industrial oil-fired heaters First Edition Portable liquid fueled catalytic appliances First Edition Oil-fired warm-air heating appliances for mobile housing and recreational vehicles Second Edition CSA B140.0-03 (R 2013) CSA B140.1-1966 (R 2015) CSA B140.2.1-10 (R 2014) CSA B140.3-1962 (R 2015) CSA B140.4-04 (R 2009) CSA B140.7-05 (R 2014) CSA B140.8-1967 (R 2015) CSA B140.9.1-1972 (R 2015) CSA B140.10-06 (R 2015) (A2LA Cert. No. 2955.08) 09/12/2017 Page 4 of 5
HVAC (Fuel Appliances Testing) (Cont.) Oil/Gas-fired commercial/industrial pressure washers and steam cleaners Second Edition Oil-burning equipment: Service water heaters for domestic hot water, space heating, and swimming pools Fourth Edition CSA CAN/CSA-B140.11-M89 (R 2014) CSA B140.12-03 (R 2013) 1 The laboratory is accredited for the test methods listed above. The accredited test methods are used in determining compliance with the specifications listed above; however, the inclusion of these specifications on this Scope does not confer laboratory accreditation to the specifications. Inclusion of these specifications on this Scope also does not confer accreditation for every method embedded within the specification. Only the methods listed above on this Scope are accredited. Testing performed for the following types of industries: Battery: Cell, Module, and Pack Aerospace Marine Heavy Equipment / Construction Furniture / Appliances Power / Utility Tele-Communications Medical Electronics Automotive, specifically the following types of mechanisms: Battery, Cell, and Module (HEV, PHEV, and EV) HVAC/R (A2LA Cert. No. 2955.08) 09/12/2017 Page 5 of 5
Accredited Laboratory A2LA has accredited TUV SUD CANADA INC. Newmarket, Ontario, Canada for technical competence in the field of Electrical Testing This laboratory is accredited in accordance with the recognized International Standard ISO/IEC 17025:2005 General requirements for the competence of testing and calibration laboratories. This accreditation demonstrates technical competence for a defined scope and the operation of a laboratory quality management system (refer to joint ISO-ILAC-IAF Communiqué dated 8 January 2009). Presented this 12 th day of September 2017. President and CEO For the Accreditation Council Certificate Number 2955.08 Valid to June 30, 2019 For the types of tests to which this accreditation applies, please refer to the laboratory s Electrical Scope of Accreditation.