CO. LTD. P.O. Box 328 Imperial, Saskatchewan Canada, S0G 2J0 Ph: (306) 963-280 Fax: (306) 963-2660 Web Site: www.ritewaymfg.com E-mail: info@ritewaymfg.com Table of Contents SPECIFICATIONS... WARNING...2 OPERATING INSTRUCTIONS...3 GREASE LOCATIONS...5 PERFECT HITCH ASSEMBLY...6 HITCH POLE ASSEMBLY...7 MAIN FRAME & BUCKET ASSEMBLY...9 BAT AND REEL ASSEMBLY... RAKE, BAT AND REEL ASSEMBLY...3 BEARING & MAIN FRAME ASSEMBLY...5 REEL MOTOR HYDRAULICS...7 RAKE, BUCKET & HITCH HYDRAULICS (ORB)...8 SELECTOR MANIFOLD ASSEMBLY...9 68 HUB BREAK DOWN...20 3-/2 x 8 (35-TC-08-25) CYLINDER...2 0, 2,000 lbs. SIDE WIND PARKING JACK...24 DECAL LOCATION...25 ROLLER CHAIN INFORMATION...27 GRADE CHART...28 TORQUE CHART...29 NOTES...30 AUG 2009 0
SPECIFICATIONS SPECIFICATIONS Model # RR-250-ST Drive Variable Hydraulic Drive Hydraulic Requirements 2-5 gal/min. @ 200-500 psi 45-57 l/min. @ 8273-034 KPa Reel Type 2 Bat Reel Chain Drive #80 Length 73 (439cm) Width 06 (269 cm) Weight 2907 lbs. (32 kg) Tires 2.5L x 5 Rake Width 50 (27cm) Reel / Bucket / Hitch Control Electric over Hydraulic Minimum Rock Diameter 2.0 (5.cm) Maximum Rock Diameter 24 (6cm) Bucket Capacity.5 Cubic Yards.5 Cubic Meters Weight Capacity 3600 lbs. 633 kg Dump Height 24 (6cm) Hydraulic Swing Hitch Optional
WARNING WARNING. This machine can kill or injure unless safety precautions are taken and observed. 2. DO NOT Have children operate this equipment. 3. DO NOT Work on this machine while hydraulic lines are under pressure. (Disconnect and Bleed lines). 4. DO NOT Put any part of your body close to the reel while the reel is in motion and/or under tension due to being jammed by any object. 5. MAKE SURE That the bat springs are not under tension while working on this machine. 6. DO NOT Allow riders at any time on this machine or on the outside the tractor. 7. DO NOT Unhook this machine from your tractor unless the bucket is empty. 8. DO NOT Allow bystanders within a 50 ft. radius while picking stones. 9. DO NOT Park this machine on an incline. Always block the wheels. 0. DO NOT Take this machine on the road unless you have done a safety and maintenance check. Make sure your machine is road worthy and have a suitable safety chain from the tractor to the main frame of the machine.. If you allow the foregoing and standard maintenance and safety practices, this machine should perform safe and trouble free. 2
OPERATING INSTRUCTIONS OPERATING INSTRUCTIONS * Always choose a level spot when manually or hydraulically moving unit into or out of transport position. Preparation for Picking Rocks. Hook rock picker up to tractor. Connect the rotary switch to a 2v power source (must have a full 2v or this could cause problems). 2. Connect the hydraulic lines to the tractor: *Large hoses are for the Reel / Motor. *Small hoses are for the Rake / Bucket and hitch. 3. Remove the safety pin or cylinder lock and swing the hitch pole into field position, either manually or hydraulically. The hitch must be swung fully into field position and then pinned into place. Note: If the unit isn t moved into field position the reel can contact the hitch. 4. Adjust the Reel RPM to ensure the proper picking speed. Proper RPM for your rotary Reel: - To pick 2 6 rocks - 45 RPM - To pick 6 2 rocks - 35 RPM - To pick 2 6 rocks - 25 RPM - To pick 6 24 rocks - Shut off rotary reel. Pick up stone with rake. Lift approximately half way up, turn on rotary reel to push rocks to the back of the bucket. Reel speed can be varied by adjusting the Flow Control Valve (Figure A). This can also be done by adjusting the flow controls in the cab of the tractor. ** IF THE REEL IS MOVING TOO FAST, DAMAGE TO THE BATS WILL RESULT. ** FIGURE A FIGURE B 3
OPERATING INSTRUCTIONS 5. Move the rotary switch to the rake position in order to pick stones. (Figure B). ONLY THOSE ROCKS ON THE SURFACE CAN BE PICKED. IF THE ROCKS ARE DUG UP FROM UNDER THE GROUND, IT WILL CAUSE DAMAGE TO THE UNIT. 6. To dump the unit, the rake must be fully lowered to the ground. Then switch over to the Bucket position. (Figure B). WARNING: DO NOT ATTEMPT TO DUMP IF THE RAKE IS IN THE UPRIGHT POSITION. 7. To use hydraulic hitch, flip rotary switch to Hitch position. Use tractor hydraulics to position hitch in desired position. (Figure B). Note: After some use the drive chain may stretch. Loosen the three nuts on the motor mount to adjust chain, tighten the chain so there is ½ of flex, then retighten the motor mount nuts. Bat Spring Placement Figure C BAT SPRING INSTALLATION THE HOOK OF THE SPRING FACES AWAY FROM THE BAT (Figure C) 4
GREASE LOCATIONS GREASE LOCATIONS The following photos show the grease locations for the RR- 250-ST. Each area is to be greased every 8 hours. Hitch Pivot Axle Bucket Pivot Brgs Rake Pivot Brgs Reel Support Bracket 5
PERFECT HITCH ASSEMBLY 3 2 ITEM # PART # DESCRIPTION 423-003 Perfect Hitch Base PP-237VR 2 423-0006 Perfect Hitch Clevis Option PP-208VR Slotted 3 530-732 ¾ Stover Lock Nut, NC, Gr.8, Pltd. 4 530-265 ¾ x 5 Capscrew, NC, Gr.8, Pltd. 4 4 3 2 ITEM 530-265 526-732 423-004 423-003 PART NUMBER QTY 3/4 X 5 CAPSCREW, NC, Gr.8, PLTD. 3/4 STOVER LOCK NUT, NC, Gr.8, PLTD. PPI-208VR CLEVIS - -/4 X -3/4 SLOTTED HOLE PERFECT HITCH PP-237VR DESCRIPTION 6
HITCH POLE ASSEMBLY HITCH POLE ASSEMBLY 3 0 2 24 30 20 5 24 3 5 27 8 2 32 9 28 20 4 25 7 8 22 3 20 27 2 6 2 29 23 4 26 7 6 22 6 9 7
HITCH POLE PARTS LIST HITCH POLE PARTS LIST ITEM # PART # DESCRIPTION 030-5989 3-/2" x 8" Hydraulic Cylinder or 030-5989(Orb, was 030-5989 2 0-253 Hitch Pole Weldment 3 0-2520 Main Frame Weldment 4 2-0555 Hitch Cylinder Lock Up 5 23-320 Hitch Pole Lock Pin 6 265-0006 4 x -/4 x /8 UHMV Plastic (White) 7 403-0269 Mulcher Tension Spring 8 407-0003 Shepherd Hook Hose Stand-off 9 409-9050 20,000 lbs. Safety Chain, Pltd. 0 49-0004 ¼ Grease Zerk, NF, Straight * 423-002 RR-250 Perfect Hitch Clevis Assembly (refer to Page 6) * 423-003 RR-250 Perfect Hitch Base Option (PP-237VR) * 423-0006 RR-250 Perfect Hitch Clevis Option PP-208VR Slotted,(refer to Page6) 2 526-063 ⅜ x -/2 Capscrew, NC, Gr.5, Pltd.(Full Thread) 3 526-0624 ⅜ x 3 Capscrew, NC, Gr.5, Pltd. 4 526-0808 ½ x Capscrew, NC, Gr.5, Pltd. 5 526-0836 ½ x 4-/2 Capscrew, NC, Gr.5, Pltd. 6 526-248 ¾ x 6 Capscrew, NC, Gr.5, Pltd. 7 530-630 x 2 Capscrew, NC, Gr.8, Pltd. 8 526-648-5 x 6 Capscrew, NC, Gr.5, Pltd. (cut to 5 ) 9 526-603 ⅜ Stover Lock Nut, NC, Gr.5, Pltd. 20 526-605 ½ Stover Lock Nut, NC, Gr.5, Pltd. 2 526-607 ¾ Stover Lock Nut, NC, Gr.5, Pltd. 22 526-609 Stover Lock Nut, NC, Gr.5, Pltd. 23 526-6206 ⅜ Hex Nut, NC, Gr.5, Pltd. 24 550-5206 ⅜ BS Flat Washer, Pltd. 25 550-5208 ½ BS Flat Washer, Pltd. 26 550-526 " Std. Flat Washer, Pltd. 27 556-0906 3/6 x -3/4 Cotter Pin, Pltd. 28 560-64 x 3-/2 Cylinder Pin, Pltd. 29 8-003 4 Steel Hose Clamp, Pltd. 30 8-020 5 Steel Hose Clamp, Pltd. 3 8-02 5 Steel Backing Plate, Pltd, 32 835-0 Tip & Chain Holder, Painted 8
MAIN FRAME & BUCKET ASSEMBLY MAIN FRAME & BUCKET ASSEMBLY 35 2 23 28 4 5 6 29 36 4 39 36 7 25 37 3 38 27 34 2 9 7 33 8 8 6 3 3 26 40 40 30 20 37 22 2 30 5 20 3 37 24 9* 0 32 9
MAIN FRAME & BUCKET PARTS LIST MAIN FRAME & BUCKET PARTS LIST ITEM # PART # DESCRIPTION 020-6007 Hub Assembly 68 6 Bolt 2 0-2505r Deflector Screen Weldment 3 0-2520 Main Frame Weldment 4 0-252 Bucket Weldment 5 0-2524 Deflector Mount 6 0-2525 Bucket Cylinder Pin Weldment 7 2-250r Shock Block c/w spacer plate 8 2-258 Rake Cylinder Lock Up (5 Long, ½ Ø Cyl. Shaft) 9 20-58 Single 68 Axle Stub c/w Hub (-3/4 spindle), 020-4040 Bolt in Spindle 9* 20-59 Single 68 Axle Stub c/wout Hub, 020-4039 9* 20-82 Single 68 Axle Stub c/wout Hub, 020-4038 (4-/2 spindle, gussets down use top hole) 0 202-6005 Dust Cap DC-5 204-5589 5 x 0 6 Bolt Wheel Rim (CTD) 2 205-93 2.5L x 5 2 Ply Farm Service Tire 020-02 2.5L x 5 Tire & Wheel Assembly 6 - Bolt 3 265-0006 4 x -/4 x /8 UHMV Plastic (White) 4 402-4027 Shock Spring 5 420-032 2,000 lbs. 0 Side Wind Parking Jake 6 422-0007 ⅜ x 3 Hitch Pin 7 426-000 Manual Tube 8 426-0002 Manual Tube Cap 426-0003 Manual Tube c/w Cap 9 526-060 ⅜ x ¼ Capscrew, NC, Gr.5, Pltd. 20 526-063 ⅜ x ½ Capscrew, NC, Gr.5, Pltd. Full Thread 2 526-0808 ½ x Capscrew, NC, Gr.5, Pltd. 22 526-008 ⅝ x Capscrew, NC, Gr.5, Pltd. 23 526-02 ⅝ x ½ Capscrew, NC, Gr.5, Pltd. 24 526-08 ⅝ x 2 ¼ Capscrew, NC, Gr.5, Pltd. 25 526-656 x 7 Capscrew, NC, Gr.5, Pltd. 26 526-603 ⅜ Stover Lock Nut, NC, Gr.5, Pltd. 27 526-605 ½" Stover Lock Nut, NC, Gr.5, Pltd. 28 526-607 ¾" Stover Lock Nut, NC, Gr.5, Pltd. 29 526-609 " Stover Lock Nut, NC, Gr.5, Pltd. 30 526-6206 ⅜ Hex Nut, NC, Gr.5, Pltd. 3 526-620 ⅝ Hex Nut, NC, Gr.5, Pltd. 32 543-5562 9/6 x ¼ NF Wheel Bolt, Pltd. 33 550-5206 ⅜" BS Plate Washer, Pltd. 34 550-5208 ½" BS Plate Washer, Pltd. 35 550-522 ¾ ID x 2 OD Flat Washer, SAE, Pltd. 36 550-526 BS Plate Washer, Pltd. 37 55-500 ⅝ Spring Lock Washer, Pltd. 38 559-50 Lynch Pin, 3/6 x ½ 39 806-52 Shock Spring Bushing 40 8-00 3 Hose Clamp 0
BAT & REEL ASSEMBLY BAT AND REEL ASSEMBLY 4 9 7 3 6 4 2 5 9 2 8 6 5 8 0 3 7
BAT & REEL PARTS LIST BAT AND REEL PARTS LIST ITEM # PART # DESCRIPTION 0-254r Bat Weldment (4 Tooth) 2 0-255r Two Bat Reel Weldment (X-Tooth) 3 252-268 H80 Q26 x -3/4 Sprocket, Tapered Hole & x 3/8 Key Way 4 26-5002 Steel Connex Bushing (-/4 OD x ) 5 26-6000 Q, -3/4 Split Tapered Bushing 6 263-0636 Key Way 3/8 x 3/8 x 2-/4 7 263-70 Key Way 3/8 x ½ x 8 292-405 Flange Bearing -3/4 Four Bolt c/w Lock Collar 9 403-0268 Bat Spring 2-/4 OD x.34 ID x L 0 525-060 3/8 x -/4 Capscrew, NC, Gr.5, Black 526-06 5/8 x 2 Capscrew, NC, Gr.5, Pltd. 2 526-66 x 2 Capscrew, NC, Gr.5, Pltd. 3 526-606 5/8 Stover Lock Nut, NC, Gr.5, Pltd. 4 526-609 Stover Lock Nut, NC, Gr.5, Pltd. 5 526-620 5/8 Hex Nut, NC, Gr.5, Pltd. 6 530-640-3.75 x 5 Capscrew, NC, Gr.8, Pltd. (Cut to 3-3/4) 7 546-029 5/8 x 4 Spade Bolt, NC, Gr.5, Pltd. 8 55-5006 3/8 Spring Lock Washer, Pltd. 9 55-500 5/8 Spring Lock Washer, Pltd. Note: Item 4 & 6 may be replaced with Part Number 526-746 ( Nylon Jam Lock Nut, NC, Gr.5, Pltd. /2 Section) and Part Number 530-640-3.25 ( x 5 Capscrew, NC, Gr.8, Pltd. Cut to 3-/4) 2
RAKE, BAT & REEL ASSEMBLY RAKE, BAT AND REEL ASSEMBLY 8 6 9 8 5 4 6 8 3 3 5 7 2 0 2 4 4 0 7 3
RAKE, BAT & REEL PARTS LIST RAKE, BAT AND REEL PARTS LIST ITEM # PART # DESCRIPTION 0-256r Rake Weldment (5 Tooth) 2 2-0r Chain Guard (26 tooth sprocket) 3 2-2507 Motor Mount 4 23-2209 Rake Pin Weldment ( Ø x 5-/4 ) 5 252-80 80 Q x -/4 Sprocket c/w 5/6 Key Way 6 263-0500 5/6 x -/2 Key 7 307-003 Parker Hyd. Motor c/w Built in Relief s, 5/8 ORB Port 8 526-008 5/8 x Capscrew, NC, Gr.5, Pltd. 9 526-020 5/8 x 2-/2 Capscrew, NC, Gr.5, Pltd. 0 526-620 5/8 Hex Nut, NC, Gr.5, Pltd. 526-7608 ½ Stover Lock Nut, NF, Gr.8, Pltd. 2 538-089 ½ x 2-/4 Capscrew, NF, Gr.8, Pltd. 3 550-520 5/8 BS Plate Flat Washer, Pltd. 4 55-500 5/8 Spring Lock Washer, Pltd. 5 556-0908 /4 x 2 Cotter Pin, Pltd. 6 262-809 #80 Chain, 39 Individual Link Plus Connector = 40 7 82-530 Motor Mount Tab, (¼ x -/2 x 3-/8) 8 2-252 Bat / Reel Assembly (refer to Page 9 for details) 4
BEARING & MAIN FRAME PARTS LIST BEARING & MAIN FRAME ASSEMBLY 6 9 7 8 5 3 3 5 0 2 5 7 6 9 5 4 4 2 4 0 4 4 5 5
BEARING & MAIN FRAME PARTS LIST BEARING & MAIN FRAME PARTS LIST ITEM # PART # DESCRIPTION 0-2520 Main Frame Weldment 2 0-2522 Bucket Bearing Weldment 3 2-2503r Rake Bearing Weldment Right Side 4 2-2504 Rake Bearing Weldment Left Side 5 2-254r Rake Split Bearing Bottom Weldment 6 49-0004 ¼ NF, Grease Zerk, Straight 7 424-000 Slow Moving Sign (SMV) 8 526-0406 ¼ x ¾ Capscrew, NC, Gr.5, Pltd. 9 526-008 ⅝ x Capscrew, NC, Gr.5, Pltd. 0 526-04 ⅝ x -3/4 Capscrew, NC, Gr.5, Pltd. 526-06 ⅝ x 2 Capscrew, NC, Gr.5, Pltd. 2 526-606 ⅝ Stover Lock Nut, NC, Gr.5, Pltd. 3 526-704 ¼ Flange Nut, NC, Gr.5, Pltd. 4 526-620 ⅝ Hex Nut, NC, Gr.5, Pltd. 5 55-500 ⅝ Spring Lock Washer, Pltd. 6 8-03 Split Rake Bearing Shim, 3/6 x Flat - 3 7 84-3038 Rake Split Bearing Top 8 806-3609 4 Std. Pipe, /8 Bucket Spacer, Painted 6
REEL MOTOR HYDRAULICS REEL MOTOR HYDRAULICS ITEM # PART # DESCRIPTION. 307-003 Parker Hyd. Motor c/w built in reliefs (500/500)5/8 ORB (TF0280AS030BBBG) 2. 308-000 Pioneer Tip ½ M Quick Connect, Poppet Type 3. 30-500 Flow Control Valve #0 ORB (CFQ-A-0) 5/8 ORB Port 4. 32-740 ½ Hose (2-Wire) ½ JIC Sw F x ½ JIC Sw F 40 5. 32-745 ½ Hose (2-Wire) ½ JIC Sw F x ½ JIC Sw F 45 6. 32-683 ½ Hose (2-Wire) ½ JIC Sw F x ½ NPT M 83 7. 36-0308 5/8 ORB M x ½ JIC M Adapter 8. 38-570 ½ JIC Sw F (Run) x (2) ½ JIC M Tee 9. 39-572 5/8 ORB M x ½ JIC M - 90º Elbow 0. 39-5720 ½ JIC Sw. F x ½ JIC M - 90º Elbow. 526-0428 ¼ x 2-/4 Capscrew, NC, Pltd. (For Flow Control, Not Shown) 2. 55-5004 ¼ Helix Spring Lock Washer, Pltd. (For Flow Control, Not Shown) 7
RAKE, BUCKET & HITCH HYDRAULICS RAKE, BUCKET & HITCH HYDRAULICS (ORB) ITEM # PART # DESCRIPTION 030-5935 3-/2 x 8 Hydraulic Cylinder, 030-5989 2 030-5936 3-/2 x 8 Hydraulic Cylinder c/w Depth Control, 030-5980 3 030-5938 3-/2 x 4 Hydraulic Cylinder, 030-599 4 308-000 ½ NPT F Male Quick Connect (Pioneer Tip) 5 30-4038 Parker 2-Volt Electric Selector Manifold ½ ORB (C394) Refer to Page 9 6 33-008 3/8 Hose (2-Wire) 3/8 JIC Sw.F x 3/8 JIC Sw.F 90 Elbow 8 7 33-0068 3/8 Hose (2-Wire) 3/8 JIC Sw.F x 3/8 JIC Sw.F 90 Elbow 68 8 33-6566 3/8 Hose (2-Wire) 3/8 JIC Sw.F x ½ NPT 66 9 33-7923 3/8 Hose (2-Wire) 3/8 JIC Sw.F x 3/8 JIC Sw.F 23 0 33-7934 3/8 Hose (2-Wire) 3/8 JIC Sw.F x 3/8 JIC Sw.F 34 33-7940 3/8 Hose (2-Wire) 3/8 JIC Sw.F x 3/8 JIC Sw.F 40 2 33-7983 3/8 Hose (2-Wire) 3/8 JIC Sw.F x 3/8 JIC Sw.F 83 3 36-0302 ½ ORB M x 3/8 JIC M - Adaptor 4 39-570 ½ ORB M x 3/8 JIC M - 90 Elbow 5 39-5729 ½ ORB M x 3/8 JIC M - 45 Elbow 6 39-5723 ½ ORB M x 3/8 JIC M - 90 Elbow Restricted 7 47-040 Wiring Harness Assy. For Three Selector Parker Manifold c/w 47-030 Control Box & (3) 47-035 (solenoid leads) 8 47-030 Control Box 3-Wire (For Parker Manifold) (Not Shown) 9 47-035 Wiring Harness Complete Assembly (Not Shown) 20 526-0508 5/6 x Capscrew, NC, Gr.5, Pltd (Not Shown) 2 55-5005 5/6 Spring Lock Washer, Pltd. (Not Shown) 8
PARKER SELECTOR MANIFOLD PARKER 2-VOLT ELECTRIC SELECTOR MANIFOLD ASSEMBLY 3 TOP 3 2 RAKE TOP TOP TOP 45 BUCKET HITCH 3 DRIVERS SIDE VIEW REAR VIEW 4 PASSENGER SIDE VIEW ITEM # PART # DESCRIPTION 30-4038 Parker 2-Volt Electric Selector Manifold C394 2 36-0302 ½ ORB M x 3/8 JIC M Adaptor 3 39-570 ½ ORB M x 3/8 JIC M 90º Elbow 4 39-5729 ½ ORB M x 3/8 JIC M 45º Elbow 9
68 HUB BREAK DOWN 68 HUB BREAK DOWN Part Number 020-6007 ITEM # PART # DESCRIPTION 203-602 S68 Spindle -3/4 2 200-6009 H68 Hub c/w Cups Only 3 20-5523 Outer Cup (LM4850) 4 20-5525 Inner Cup (LM25520) 5 202-6005 Dust Cap (DC 5) 6 290-555 Outer Wheel Bearing (LM48548) 7 290-559 Inner Wheel Bearing (LM25580) 8 295-5576 Seal (SE30) 9 49-0004 ¼ grease Zerk, NF, Straight 0 534-786 Castle Nut, NF 543-5562 9/6 Wheel Stud UNF 2 554-5303 Spindle Washer WA2 3 556-064 3/6 x -3/4 Cotter Pin, Black 4 020-6007 H68 Hub Assembly 20
CYLINDER BREAKDOWN 3-/2 x 8 (35-TC-08-25) CYLINDER c/w STROKE CONTROL Rite Way Part Number 030-5936 (3/4 ORB) Rite Way Part Number 030-5980 (3/4 ORB) 030-5936 ITEM # PART # DESCRIPTION 492403 3-2 Clevis Cap 2 492423 Rod Cap 3 492528 3-/2 Piston 4 492088 -/4 Rod 5 49798 3-/2 Tube 6 492278 Tie Rod 7 458600 Rod Clevis 8 639577 Seal Kit 9 63737 Stroke Control (Not Shown) 2
CYLINDER BREAKDOWN 3-/2 x 8 (35-TC-08-25) CYLINDER Rite Way Part Number 030-5935 (3/4 ORB) Rite Way Part Number 030-5989 (3/4 ORB) 030-5935 ITEM # PART # DESCRIPTION 492403 3-2 Clevis Cap 2 492423 Rod Cap 3 492528 3-/2 Piston 4 492088 -/4 Rod 5 49798 3-/2 Tube 6 492578 Tie Rod 7 458600 Rod Clevis 8 639577 Seal Kit 22
CYLINDER BREAKDOWN 3-/2 x 4 (35-TC-4-25) CYLINDER Rite Way Part Number 030-5938 (3/4 ORB) Rite Way Part Number 030-599 (3/4 ORB) 030-5938 ITEM # PART # DESCRIPTION 492820 3-2 Clevis Cap 2 492822 Rod Cap 3 492528 3-/2 Piston 4 492872 -/4 Rod 5 49804 3-/2 Tube 6 492344 Tie Rod 7 458652 Rod Clevis 8 639577 Seal Kit 23
PARKING JACK BREAKDOWN 0, 2,000 lbs. SIDE WIND PARKING JACK ITEM # PART # DESCRIPTION 420-008 Side Wind Crank Kit 2 420-009 Gear Set 3 420-0020 Hitch Pin c/w Chain 4 420-002 Screw Replacement Kit 5 420-046 Inner Ram Assembly 6 526-0424!/4 x 3 Capscrew, UNC 7 526-7006!/4 Lock Nut. UNC 8 420-0024 Cover 9 420-0025 Body 24
DECAL LOCATIONS DECAL LOCATION 2 5 7 6 9 ON THE TOP 3 5 3 4 3 8 2 2 DECALS SHOWN HERE ARE PLACED ON FRAME 0 3 6 4 4 3 0 25
DECAL LOCATIONS DECAL LOCATION ITEM # PART # QTY DESCRIPTION 060-0072 2 Rite Way MFG. (Large White Decal, 3 x 5) 2 060-0096 2 RR-250-ST (Large White Decal, 25 x 2-/2) 3 060-0009 4 Amber Reflector (3 x 2) 4 060-0022 2 Red Reflector (3 x 2) 5 060-005 Important - Block Wheel Before Unhooking (5-/2 x 3) 6 060-0092 2 Rite Way MFG. (Small White Decal, Place on Bucket, 9 x 4) 7 060-0038 Attention - Insure That All Cylinder Shafts (3-/2 x -/2) 8 060-0078 Caution - Do Not Dump Hopper (4 x 2) 9 060-00 Caution - Escaping Fluid Hazard (6 x 2-5/8) 0 060-003 2 Caution - Re-Pack Bearings After First 500 Acres (3-/2 x -/4) 060-0046 7 Grease Every 8 Hours (-/4 x -/4) 2 060-0067 Warning - Check And Tighten Hub And Wheel Bolts (4 x 2) 3 060-0037 Warning - This Machine Can Kill (Big Yellow, 8-/2 x 6-/2) 4 060-0069 Warning - Rotating Part Hazard (3-/2 x 3) 5 060-0034 Serial Number Plate c/w Rivet (50-000) 6 060-0028 Lower or block Elevated Component (not shown) 7 060-0068 Bucket Must Be Completely Dumped. (not shown) 26
ROLLER CHAIN ROLLER CHAIN INFORMATION 27
GRADE CHART GRADE CHART 28
TORQUE CHART TORQUE CHART 29
NOTES NOTES 30