Models K, BK, FK, F, BF and FF Uses the Optimal Bearing To ensure the rigidity alance with the Ball Screw, the uses an angular earing (contact angle: 30 ; DF con guration) with a high rigidity and a low torque. Miniature models K/FK 4, 5 and 6 are incorporated with a miniature angular earing with a contact angle of 45 developed exclusively for miniature Ball Screws. This earing has a greater contact angle of 45 and an increased numer of alls with a smaller. The high rigidity and accuracy of the miniature angular earing provides the stale rotational performance. exagonal socket-head setscrew Set piece ock nut olding lid Seal ousing Bearing Collar ousing Bearing Snap ring Shapes The square and round shapes are availale for the to allow the selection according to the intended use. Compact and asy Installation The is compactly designed to accommodate the space in the installation site. As the earing is provided with an appropriately adjusted preload, the can e assemled with a Ball Screw unit with no further machining. Accordingly, the required man-hours in the assemly can e reduced and the assemly accuracy can e increased. Fixed side Structure and Features Fig. Structure of the Supported side The comes in six types: models K, FK, F, and FF, which are standardized for the standard Ball Screw assemly provided with the nished shaft ends, and models BK and BF, which are standardized for all screws in general. The on the xed side contains a JIS Class 5-compliant angular earing provided with an adjusted preload. The miniature type models K/FK 4, 5 and 6, in particular, incorporate a miniature earing with a contact angle of 45 developed exclusively for miniature Ball Screws. This provides stale rotational performance with a high rigidity and an accuracy. The on the supported side uses a deep-groove all earing. The internal earings of the models K, FK and BK contain an appropriate amount of lithium soap-group grease that is sealed with a special seal. Thus, these models are capale of operating over a long period.
Type Types of s and Applicale Screw Shaft Outer Diameters For the Fixed Side Square Type Model K Speci cation Tale (Inner : 4 to 20) Round Type Model FK Speci cation Tale (Inner : 4 to 30) For the Supported Side Square Type Model F Speci cation Tale Square Type Model BK Speci cation Tale (Inner : 0 to 40) Square Type Model BF Speci cation Tale Inner of xed-side (mm) Inner of supportedside Support Unit (mm) 4 5 6 6 8 6 0 8 2 0 5 5 Applicale Model of xed-side Support Unit K 4 FK 4 K 5 FK 5 K 6 FK 6 K 8 FK 8 K 0 FK 0 BK 0 K 2 FK 2 BK 2 Applicale model of the supported side Type BNK with Un nished Shaft nds(applicale Model ) BNK040 BNK050 Recommended Shapes of Shaft nds(applicale Shaft Outer Diameter D) Shaft nd (mm) Shaft nd J (mm) 6 BNK060 8 F 6 FF 6 F 8 FF 6 F 0 FF 0 BF 0 F 2 FF 2 BF 2 BNK080 BNK0802 BNK080 8 BNK002 2 BNK004 BNK00 BNK202 BNK205 BNK208 BNK402 BNK404 BNK408 BNK50 BNK520 BNK66 BNK200 BNK2020 4 5 6 8 4 5 6 8 K 5 F 5 20 FK 5 FF 5 25 BK 5 BF 5 20 BK BF 25 20 20 25 25 30 30 K 20 FK 20 F 20 FF 20 BNK2520 28 30 32 BK 20 BF 20 28 30 32 FK 25 FF 25 36 BK 25 BF 25 36 FK 30 FF 30 BK 30 BF 30 40 40 35 35 BK 35 BF 35 45 (Inner : 6 to 20) Round Type Model FF Speci cation Tale (Inner : 8 to 40) 40 40 BK 40 BF 40 Note) The Supports Units in this tale apply only to those Ball Screw models with recommended shaft ends shapes, J and K, indicated on. Note2) For Recommended Shapes of Shaft nds, J, and K; refer to pages to. 50 55 (Inner : 6 to 30)
Model Numers of Bearings and Characteristic Values xample of Installation Support Unit model K 4 FK 4 K 5 FK 5 K 6 FK 6 K 8 FK 8 K 0 FK 0 BK 0 K 2 FK 2 BK 2 K 5 FK 5 BK 5 BK K 20 FK 20 BK 20 FK 25 BK 25 FK 30 BK 30 BK 35 BK 40 Angular all earing on the xed side Deep-groove all earing on the supported side Bearing AC4-2 AC5-4 AC6-6 9M8A 000 00 002 203 204 004 205 206 20 208 Basic dynamic load rating Ca (kn) Axial direction Note) ermissile load (kn) Rigidity (N/ m) Support Unit model Bearing model Radial direction Basic dynamic load rating C(kN) Basic static load rating C 0 (kn) 0.93. 2.24 29.38.6 35 F 6 FF 6 606ZZ 2.9 0.8 2.93 2.5 49 F 8 606ZZ 2.9 0.8 6.08 3. 65 6.66 3.25 88.6 4 00 F 0 FF 0 BF 0 F 2 FF 2 BF 2 F 5 FF 5 BF 5 608ZZ 3.35.4 6000ZZ 4.55.96 6002ZZ 5.6 2.84 3. 5.85 25 BF 6203ZZ 9.6 4.6.9 9.5 0 F 20 FF 20 6204ZZ 2.8 6.65 2..55 40 BF 20 6004ZZ 9.4 5.05 20.2.5 90 28 6.3 95 Note) ermissile load indicates the static permissile load. FF 25 BF 25 FF 30 BF 30 6205ZZ 4.85 6206ZZ 9.5.3 3.2 2.9 255 BF 35 620ZZ 25. 5.3 44. 2. 20 BF 40 6208ZZ 29..8 Square Type Fig.2 xample of Installing a Square Type Round Type Fig.3 xample of Installing a Round Type
Mounting rocedure Installing the () Install the xed side with the screw shaft. (2) After inserting the xed side, secure the lock nut using the fastening set piece and the hexagonal socket-head setscrews. (3) Attach the supported side earing to the screw shaft and secure the earing using the snap ring, and then install the assemly to the housing on the supported side. Note) Do no disassemle the. Note2) When inserting the screw shaft to the, take care not to let the oil seal lip turn outward. Note3) When securing the set piece with a hexagonal socket-head setscrew, apply an adhesive to the hexagonal sockethead setscrew efore tightening it in order to prevent the screw from loosening. If planning to use the product in a harsh environment, it is also necessary to take a measure to prevent other components/parts from loosening. Contact TK for details. Checking the Accuracy and Fully Fastening the While checking the runout of the all screw shaft end and the axial clearance using a dial gauge, fully fasten the all screw nut, the nut racket, the xed side and the supported-side, in this order. Measure the axial clearance Adjust the nut y moving the tale so that the nut travels smoothly throughout the whole stroke. Measure the runout Snap ring Bearing exagonal socket-head setscrew Set piece Supported side ock nut Collar Fixed side Installation onto the Tale and the Base () If using a racket when mounting the all screw nut to the tale, insert the nut into the racket and temporarily fasten it. (2) Temporarily fasten the xed side to the ase. In doing so, press the tale toward the xed side to align the axial center, and adjust the tale so that it can travel freely. If using the xed side as the reference point, secure a clearance etween the all screw nut and the tale or inside the racket when making adjustment. If using the tale as the reference point, make the adjustment either y using the shim (for a square type ), or securing the clearance etween the outer surface of the nut and the inner surface of the mounting section (for a round type ). (3) ress the tale toward the xed-side to align the axial center. Make the adjustment y reciprocating the tale several times so that the nut travels smoothly throughout the whole stroke, and temporarily secure the to the ase. Connection with the Motor () Mount the motor racket to the ase. (2) Connect the motor and the all screw using a coupling. Note) Make sure the mounting accuracy is maintained. (3) Thoroughly perform the reak-in for the system. Coupling Motor Supported side support unit Tale Bracket Fixed side support unit Base
Types of Recommended Shapes of the Shaft nds To ensure speedy estimates and manufacturing of Ball Screws, TK has standardized the shaft end shapes of the screw shafts. The recommended shapes of shaft ends consist of shapes, K and J, which allow standard s to e used. Mounting method Symol for shaft end shape Shape Supported Support Unit FK K J BK Fixed J 2 J2 BK FK K 3 FK K J3 BK Supported K FF F BF
Model K Square Type on the Fixed Side 2- through hole, 2 counter ore depth h M B 2 4 2 3 5 2- through hole M B 4 2 2 3 5 2- through hole h h T T B 6 3 B 6 3 Model Models K 4 and 5 Models K 6 and 8 Shaft d 2 3 B K 4 4 5 5.5.5 3 34 9 K 5 5 6.5 5.5 8.5 3.5 36 2 8 K 6 6 20 5.5 22 3.5 42 25 2 K 8 8 23 26 4 52 32 26 K 0 0 24 6 29.5 6 0 43 35 K 2 2 24 6 29.5 6 0 43 35 K 5 5 25 6 36 5 80 49 40 K 20 20 42 0 50 0 95 58 4.5 h Models K 0 to 20 Mass Bearing used B d d 2 h M T kg 0 8 26 4.5 M2.6 0 AC4-2 0.06 20 8 28 4.5 M2.6 AC5-4 0.08 3 8 20 30 5.5 9.5 M3 2 AC6-6 0.4 25 26 38 6.6 2 M3 4 9M8A 0.24 25 36 24 52 9 M3 6 000 0.46 25 36 24 52 9 M3 9 00 0.44 30 4 25 60 M3 22 002 0.55 30 56 25 5 M4 30 204.35 art Models K 4 to 8 art name of units ousing 2 Bearing set 3 Set nut 4 Collar 2 5 Seal 6 ock Nut exagonal socket-head setscrew (with a set piece) art Models K 0 to 20 art name of units ousing 2 Bearing set 3 olding lid 4 Collar 2 5 Seal 2 6 ock Nut exagonal socket-head setscrew (with a set piece)
Model BK Square Type on the Fixed Side 4- through hole, 2 counter ore depth h M 2 3 B T 4-3 4 2 5 h 6 3 B C C2 Model Shaft d 2 3 B h B BK 0 0 25 5 29 5 60 39 30 22 34 32.5 BK 2 2 25 5 29 5 60 43 30 25 35 32.5 BK 5 5 2 6 32 6 0 48 35 28 40 38 BK 35 9 44 86 64 43 39 50 55 BK 20 20 35 8 43 8 88 60 44 34 52 50 BK 25 25 42 2 54 9 06 80 53 48 64 0 BK 30 30 45 4 6 9 28 89 64 5 6 8 BK 35 35 50 4 6 2 40 96 0 52 88 9 BK 40 40 6 8 6 5 60 0 80 60 00 90 Mass C C 2 d 3 d d 2 h M T Bearing used kg 5 46 3 6 5.5 6.6 0.8 5 M3 6 000 0.39 8 46 3 6 5.5 6.6 0.8.5 M3 9 00 0.4 8 54 5 6 5.5 6.6 6.5 M3 22 002 0.5 28 68 9 8 6.6 9 4 8.5 M4 24 203.2 22 0 9 8 6.6 9 4 8.5 M4 30 004.9 33 85 22 0 9.5 M5 35 205 2.3 33 02 23 4 20 3 M6 40 206 3.32 35 4 26 2 4 20 3 M8 50 20 4.33 3 30 33 4 4 8 26.5 M8 50 208 6.5 art art name of units ousing 2 Bearing set 3 olding lid 4 Collar 2 5 Seal 2 6 ock Nut exagonal socket-head setscrew (with a set piece)
Model FK Round Type on the Fixed Side F 5 2 4 3 6 4-φ φ d through hole, d2 counter ore depth h (90 equidistant) M F 2 T φ Dg6 φ d CD φ A B T R0.6MAX T2 Model Shaft Mounting method A Models FK 4 to 8 d F D A CD B FK 4 4 5 6 9.5 0.006 8 0.0 FK 5 5 6.5 6 0.5 8.5 0.00 20 0.02 FK 6 6 20 3 22 0.00 22 0.02 FK 8 8 23 9 4 26 0.00 28 0.02 32 24 25 34 26 26 36 28 28 43 35 35 Installation procedure A Installation procedure B Mounting method B Bearing used T 2 T 2 d d 2 h M T kg 5.5 3 6.5 4 3.4 6.5 4 M2.6 0 AC4-2 0.05 5.5 3.5 5 3.4 6.5 4 M2.6 AC5-4 0.06 5.5 3.5 8.5 6.5 3.4 6.5 4 M3 2 AC6-6 0.08 4 0 3.4 6.5 4 M3 4 9M8A 0.5 Mass art art name of units ousing 2 Bearing set 3 Set nut 4 Collar 2 5 Seal 6 ock Nut exagonal socket-head setscrew (with a set piece)
Model FK Round Type on the Fixed Side F 5 2 4 3 6 4-φ φ d through hole, d2 counter ore depth h (90 equidistant) M F 2 T φ Dg6 φ d CD φ A B T R0.6MAX T2 Model Shaft Mounting method A Models FK 0 to 30 d F D A CD B FK 0 0 2 0 29.5 0.009 34 0.025 FK 2 2 2 0 29.5 0.009 36 0.025 FK 5 5 32 5 36 0.009 40 0.025 FK 20 20 52 22 30 50 0.0 5 0.029 FK 25 25 5 2 30 60 0.0 63 0.029 FK 30 30 62 30 32 6 0.0 5 0.029 52 42 42 54 44 44 63 50 52 85 0 68 98 80 9 95 93 Installation procedure A Installation procedure B Mounting method B Bearing used T 2 T 2 d d 2 h M T kg.5 5 8.5 6 4.5 8 4 M3 6 000 0.2.5 5 8.5 6 4.5 8 4 M3 9 00 0.22 0 6 2 8 5.5 9.5 6 M3 22 002 0.39 8 0 2 4 6.6 0 M4 30 204.09 3 0 20 9 5 3 M5 35 205.49 2 8.5 5 M6 40 206 2.32 Mass art art name of units ousing 2 Bearing set 3 olding lid 4 Collar 2 5 Seal 2 6 ock Nut exagonal socket-head setscrew (with a set piece)
Model F Square Type on the Supported Side B 2- through hole 3 2 2- through hole, 2 counter ore depth h B 3 2 h TK F* h TK F* B B Model Shaft Models F 6 and 8 d B h F 6 6 2 42 25 2 3 8 F 8 6 4 52 32 26 25 F 0 8 20 0 43 35 25 36 F 2 0 20 0 43 35 25 36 F 5 5 20 80 49 40 30 4 F 20 20 26 95 58 4.5 30 56 Note) The area marked with * is imprinted with a numeric character(s) as part of the model numer. B Models F 0 to 20 Bearing Snap ring Mass used used d d 2 h kg 20 30 5.5 9.5 606ZZ C6 0.0 26 38 6.6 2 606ZZ C6 0.3 24 52 9 608ZZ C8 0.33 24 52 9 6000ZZ C0 0.32 25 60 9 6002ZZ C5 0.38 25 5 6204ZZ C20 0.63 art art name of units ousing 2 Bearing 3 Snap ring
Model BF Square Type on the Supported Side 2- through hole, 2 counter ore depth h 3 2 B 4-3 h TK BF* B Model Shaft d B h B BF 0 8 20 60 39 30 22 34 32.5 BF 2 0 20 60 43 30 25 35 32.5 BF 5 5 20 0 48 35 28 40 38 BF 23 86 64 43 39 50 55 BF 20 20 26 88 60 44 34 52 50 BF 25 25 30 06 80 53 48 64 0 BF 30 30 32 28 89 64 5 6 8 BF 35 35 32 40 96 0 52 88 9 BF 40 40 3 60 0 80 60 00 90 Note) The area marked with * is imprinted with a numeric character(s) as part of the model numer. Bearing used Mass Snap ring used d 3 d d 2 h kg 5 46 5.5 6.6 0.8 5 608ZZ C8 0.29 8 46 5.5 6.6 0.8.5 6000ZZ C0 0.3 8 54 5.5 6.6 6.5 6002ZZ C5 0.38 28 68 6.6 9 4 8.5 6203ZZ C 0.4 22 0 6.6 9 4 8.5 6004ZZ C20 0.6 33 85 9.5 6205ZZ C25.42 33 02 4 20 3 6206ZZ C30.9 35 4 4 20 3 620ZZ C35 2.22 3 30 4 8 26.5 6208ZZ C40 3.2 art art name of units ousing 2 Bearing 3 Snap ring
Model FF Round Type on the Supported Side 4- through hole, 2 counter ore depth h (90 equidistant) F 2 3 φ Dg6 φ d CD φ A B R0.6MAX Model Shaft d F D A FF 6 6 0 6 4 22 0.00 0.02 FF 0 8 2 5 28 0.00 0.02 FF 2 0 5 8 34 0.009 0.025 FF 5 5 9 8 40 0.009 0.025 FF 20 20 20 9 5 0.0 0.029 FF 25 25 24 4 0 63 0.0 0.029 FF 30 30 2 8 9 5 0.0 0.029 36 43 52 63 85 98 Mass Bearing used Snap ring used CD B d d 2 h kg 28 28 3.4 6.5 4 606ZZ C6 0.04 35 35 3.4 6.5 4 608ZZ C8 0.0 42 42 4.5 8 4 6000ZZ C0 0. 50 52 5.5 9.5 5.5 6002ZZ C5 0.2 0 68 6.6 6.5 6204ZZ C20 0.2 80 9 9 4 8.5 6205ZZ C25 0.6 95 93.5 6206ZZ C30.0 art art name of units ousing 2 Bearing 3 Snap ring
Recommended Shapes of Shaft nds - Shape (, 2 and 3) (For Models FK and K) Shape 3 R K K2 K3 Width G, depth T Shape 2 J M (Metric screw thread) φ A h Shape φ B h φ d Model FK model Ball screw shaft outer Model FK Shaft outer of the earung Model K Metric screw thread Model FK Model K d A B F M S FK4 K4 6 4 3 23 5 M4 0.5 FK5 K5 5 4 25 6 M5 0.5 8 FK6 K6 6 4 30 8 M6 0.5 8 FK8 K8 2 8 6 35 9 M8 0 FK0 K0 4 0 8 36 5 M0 FK0 K0 5 0 8 36 5 M0 FK2 K2 6 2 0 36 5 M2 FK2 K2 8 2 0 36 5 M2 FK5 K5 20 5 2 49 20 M5 3 FK5 K5 25 5 2 49 20 M5 3 FK20 K20 28 20 64 25 M20 FK20 K20 30 20 64 25 M20 FK20 K20 32 20 64 25 M20 FK25 36 25 20 6 30 M25.5 20 FK30 40 30 25 2 38 M30.5 25 Note) s are designed to have dimensions so that cominations of models FK and FF, models K and F or models BK and BF are used on the same shaft. If desiring the shaft end to e machined at TK, add the shape symol in the end of the Ball Screw model numer. (xample) TS2505+500-2K (Shape 2 on the xed side; shape K on the supported side) For the perpendicularity of the end face of the earing, refer to JIS B 92-99. Width across at J N G N9 F S N Shape 2 Shape 3 position Keyway Cut at on two side Model FK Model K T +0. 0 R K K 2 K 3 4 4 4 2. 4.5 0.5.5 5 4 4 3. 5 2 0.5 2 5 4 4 3. 6 3.5 0.5 3.5 8 5 5 5.6 3.5 0.5 3.5 0 5 2.2.5 0.5 0.5 0.5 0 5 2.2.5 0.5 0.5 0.5 3 6 8 3.8 2 9.5 2 0.5 0.5 0.5 3 6 8 3.8 2 9.5 2 0.5 0.5 0.5 6 6 9 4 2.5 6.3 6 4 2 5 8 0 4 2.5 6.3 6 4 2 5 2 8 5 3 2 6 2 3 24 8 2 5 3 2 6 2 3 2 9 3 5 3 2 6 2 3 2 0 3 6 3.5 25 9 25 5 2 32 0 5 8 4 32 23.5 32 3 9 Note) The all nut ange faces the xed side unless otherwise speci ed. If desiring the ange to face the supported side, add symol G in the end of the Ball Screw model numer when placing an order. (xample) BIF2505-5RRGO+420C5-2KG
Recommended Shapes of Shaft nds - Shape J (J, J2 and J3) (For Model BK) Shape J3 R Width G, depth T Shape J2 J M (Metric screw thread) φ A h Shape J φ B h φ d model Ball screw shaft outer Shaft outer of the earung Model BK Model BK d A B F M Metric screw thread BK0 4 0 8 39 5 M0 BK0 5 0 8 39 5 M0 BK2 6 2 0 39 5 M2 BK2 8 2 0 39 5 M2 BK5 20 5 2 40 20 M5 BK 25 5 53 23 M BK20 28 20 53 25 M20 BK20 30 20 53 25 M20 BK20 32 20 53 25 M20 BK25 36 25 20 65 30 M25.5 BK30 40 30 25 2 38 M30.5 BK35 45 35 30 83 45 M35.5 BK40 50 40 35 98 50 M40.5 BK40 55 40 35 98 50 M40.5 Note) s are designed to have dimensions so that cominations of models FK and FF, models K and F or models BK and BF are used on the same shaft. If desiring the shaft end to e machined at TK, add the shape symol in the end of the Ball Screw model numer. (xample) TS2505+500-J2K (Shape J2 on the xed side; shape K on the supported side) For the perpendicularity of the end face of the earing, refer to JIS B 92-99. Width across at S J N G N9 F S N Shape J2 Shape J3 Keyway Cut at on two side T +0. 0 R 6 0 5 2.2.5 6 0 5 2.2.5 4 3 6 8 3.8 2 9.5 2 4 3 6 8 3.8 2 9.5 2 2 6 6 9 4 2.5 6.3 6 8 0 5 3 2 4.3 2 5 2 8 5 3 2 6 2 5 24 8 2 5 3 2 6 2 5 2 9 3 5 3 2 6 2 8 2 0 3 6 3.5 25 9 25 25 32 0 5 8 4 32 23.5 32 28 36 2 5 8 4 40 28.5 40 35 4 4 9 0 5 45 33 45 35 46 4 20 0 5 45 33 45 Note) The all nut ange faces the xed side unless otherwise speci ed. If desiring the ange to face the supported side, add symol G in the end of the Ball Screw model numer when placing an order. (xample) BIF2505-5RRGO+420C5-J2KG
Recommended Shapes of Shaft nds - Shape K (For Models FF, F and BF) φ A h Model K φ B 0-0.2 G +0.4 0 Model FF Model FF Model F Model BF F +0.2 0 model Ball screw shaft outer Shaft outer of the earung Model FF Model F Model BF d A FF6 F6 8 6 F8 2 6 FF0 F0 BF0 4 8 FF0 F0 BF0 5 8 FF2 F2 BF2 6 0 FF2 F2 BF2 8 0 FF5 F5 BF5 20 5 FF5 F5 BF5 5 25 BF * FF20 F20 BF20 ** 28 20 FF20 F20 BF20 ** 30 20 FF20 F20 BF20 ** 32 20 FF25 BF25 36 25 FF30 BF30 40 30 BF35 45 35 BF40 50 40 BF40 55 40 Note) s are designed to have dimensions so that cominations of models FK and FF, models K and F or models BK and BF are used on the same shaft. If desiring the shaft end to e machined at TK, add the shape symol in the end of the Ball Screw model numer. (xample) TS2505+500-2K (Shape 2 on the xed side; shape K on the supported side) For the perpendicularity of the end face of the earing, refer to JIS B 92-99. Snap ring groove B F G 9 5. 6.8 0.8 9 5. 6.8 0.8 0.6.9 0.9 0.6.9 0.9 9.6 9.5.5 9.6 9.5.5 3 4.3 0.5.5 3 4.3 0.5.5 6 6.2 3.5.5 9 (6) 9 5.35 (3.35).35 9 (6) 9 5.35 (3.35).35 9 (6) 9 5.35 (3.35).35 20 23.9 6.35.35 2 28.6.5.5 22 33 8.5.5 23 38 9.95.95 23 38 9.95.95 Note) *When model BK (shaft end shape: J) is used on the xed side for a Ball Screw with a shaft outer of 25 mm, the shaft end shape on the supported side is that for model BF. **The dimensions in the parentheses in the tale aove are that of model BF20. They differ from those of models FF20 and F20. When placing an order, e sure to specify the model numer of the to e used.