EMC COMBILINE MADE IN GERMANY EMC solutions
KEB COMBILINE EMC compatibility plays an important role in the operating safety of machines and equipment. Manufacturers and operators are required to implement the installed systems so as to achieve electrical compliance with the limits (for emissions) and requirements (for fault-free operations) set out in the standards and regulations! To this end, the following standards must be applied as per the order below: Product standard: This standard applies to an exactly defined application area that generally meets the special requirements of a product family. Example: The so-called power drives systems (PDS) (inverter and motor viewed in terms of a drive) belong to the product family standards EN 61800-x (-x). EN 61800-3 is the EMC standard. Basic technical standard: This standard sets out the requirements for a specific environment. Example: The EN 61000-6-x series applies to machine builders; it sets out the general EMC requirements for use either in a public low-voltage grid or an industrial grid. EN 61000-6, -3 and -4 Emissions EN 61000-6, -1 and -2 Emissions Basic standard: This standard describes the measurement methods and instruments for the testing process itself, provides information on limits or minimum requirements without relating the same to a subsequent place of use. That is done by the basic technical standard. Basis for the EN 61000-4 -x standards series KEB develops, produces and supplies a comprehensive range of interference suppression components for the mains- and motor-related optimisation of operating conditions. With the help of a mobile EMC on-site service, our measurements and advisory services can assist you in selecting the proper components and their application. Calibrated measurement instruments and the relevant software can be used to prepare documents that verify compliance with EMC requirements. 2 Contents page Introduction EMC compatibility 2 Mains Mains chokes 4 Harmonic filters 6 Standard HF filters 8 Low-leakage current IT-HF filters 10 Central HF filters, E6 series 12 Comprehensive EMC services 14 Motor Motor chokes 16 Sinusoidal filters 18 Combinations NHF-filters 22 I/O-filtesr 23 Nomenclature Electrical Mechanical Nominal current Ø Wire size Power loss, calculated B Total length from base f Netz Mains frequency H Width from base I ab Leakage current H 1 Width from base - coil design or cable P FU Nominal capacity drive controller [kw] or [HP] T Height from base - clamps L Inductance a 1 a 2 a 3 a 4 Distance fastening holes f s Switching frequency inverter d 1 d 2 Diameter fastening holes f max Maximum motor frequency Cu Copper portion U max Maximum operating voltage m Total weight
Filters and chokes The operation of variable-speed drives with intermediate voltage circuits puts stress on the mains and motor, which can be optimised with the following additional measures (depending on the place of use and type of application): Mains Mains chokes reduce harmonics and in-rush current to the mains and increase the service life of components in the devices. Harmonics filters reduce the harmonics resulting in sinusoidal current consumption without the voltage losses that occur with mains chokes. HF filters for high-frequency interference suppression of single and multi-axis systems Standard reduced leakage current IT mains Motor Output chokes for application areas up to 100 Hz (customer-specific solutions up to 1600 Hz) Sinusoidal filters create sinusoidal motor voltages and reduce motor losses. Available for output frequencies up to 100 Hz, 200 Hz, 800 Hz and 1600 Hz Sinusoidal EMC filters as a combination of sinusoidal filters with EMC level reduce symmetrical and asymmetrical interference and support compliance with statutory limits for installations without shielded motor cables (on request). Combine as special all-in-one solution NHF filters combine the effects of EMC filters and mains chokes I/O filters combine the mains-side HF filter and motor-side du/dt filter in a functional assembly with reduced and space-saving installation requirements. 3
KEB COMBILINE mains-side Mains chokes optimise the harmonics to the mains power supply which result from the pulse-shaped charging of uncontrolled rectifiers and reduce the effective input current. This decrease in stress has the direct effect of significantly increasing the service life of the link voltage capacitors in inverters and servo drives and reducing the stress on the input rectifier. Chokes for 1-phase or 3-phase units are universally designed for a frequency range of 45-65 Hz. Nominal inductance is determined by the 4 % short circuit voltage at nominal current and frequency. With respect to the chokes, please ensure sufficient installation space to take into account higher heat emissions and a strong magnetic leakage field. Mains choke 1-phase 230 V AC (U max = 264 V), 50/60 Hz f Netz Ø B H H 1 T a 1 a 3 d 1 d 2 Weight Part-No. [A] [W] [Hz] [mm 2 ] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] Cu [kg] m [kg] 05Z1B02-1000 6 9 45-65 4 60 47 53 80 44 36 3.6 7 0.1 0.5 07Z1B02-1000 10 9 45-65 4 85 59.5 65 89 64 46.5 4.8 9 0.3 1.4 09Z1B02-1000 16 15 45-65 4 85 60 65 89 64 50 4.8 9 0.3 1.5 10Z1B02-1000 20 15 45-65 16 85 60 65 89 64 50 4.8 9 0.3 1.5 12Z1B02-1000 25 18 45-65 16 85 60 65 89 64 50 4.8 9 0.4 2.6 4 Mains choke 3-phases 230 V AC (U max = 264 V), 50/60 Hz f Netz Ø B H H 1 T a 1 a 2 a 3 d 1 d 2 Weight Part-No. [A] [W] [Hz] [mm 2 ] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] Cu [kg] m [kg] 05Z1B03-1000 2.4 15 45-65 4 100 54 54 120 80-39 4.8 8 0.1 0.8 07Z1B03-1000 4.2 20 45-65 4 100 54 54 120 80-39 4.8 8 0.2 0.9 09Z1B03-1000 7.4 26 45-65 4 100 54 54 122 80-39 4.8 8 0.4 1.1 10Z1B03-1000 10.5 28 45-65 4 100 63 63 122 80-47 4.8 8 0.5 1.5 12Z1B03-1000 17.3 52 45-65 4 148 67 67 145 136-47 4.8 8 0.7 2.0 13Z1B03-1000 25.2 55 45-65 16 148 77 77 145 136 90 58 4.8 8 0.8 3.7 14Z1B03-1000 34.7 59 45-65 16 148 77 77 145 136 90 58 4.8 8 1.1 5 15Z1B03-1000 50.4 88 45-65 16 178 90 90 175 166 113 69 4.8 8 1.8 5.8 16Z1B03-1000 69.5 110 45-65 M8 219 100 130 160 201 136 70 7 12 2.8 7.4 17Z1B03-1000 88.2 125 45-65 M8 219 110 140 170 201 136 80 7 12 3.3 9.6 18Z1B03-1000 105 136 45-65 M8 219 120 150 170 201 136 90 7 12 4.2 12.1 19Z1B03-1000 121 170 45-65 M8 243 115 155 180 225 156 85 7 12 4 12.2 20Z1B03-1000 152.3 185 45-65 M8 243 126 165 180 225 156 96 7 12 4.5 15 21Z1B03-1000 189 200 45-65 M10 267 133 173 202 249 176 82 7 12 7.1 21.6 Percentage of harmonics single phase 230 V Unchoked Choked with uk = 4 % Percentage of harmonics 3-phase 400 V Unchoked Harmonic number Choked with uk = 4 % Harmonic number
Mains chokes Mains choke 3-phases 400 V AC (U max = 550 V), 50/60 Hz f Netz Ø B H H 1 T a 1 a 2 a 3 d 1 d 2 Weight Part-No. [A] [W] [Hz] [mm 2 ] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] Cu [kg] m [kg] Fig. 05Z1B04-1000 1.4 10 45-65 4 100 55 55 121 80-40 4.8 8 0.2 0.8 1 07Z1B04-1000 2.7 19 45-65 4 100 55 55 121 80-40 4.8 8 0.3 0.9 1 09Z1B04-1000 4.3 23 45-65 4 100 55 55 121 80-40 4.8 8 0.4 1.1 1 10Z1B04-1000 6.1 24 45-65 4 100 64 64 121 80-47 4.8 8 0.5 1.5 1 12Z1B04-1000 10 37 45-65 4 148 68 68 145 136 90 48 4.8 8 0.8 2.1 1 13Z1B04-1000 12.6 48 45-65 4 148 78 78 145 136 90 59 4.8 8 0.7 2.6 1 14Z1B04-1000 17.3 69 45-65 4 148 77 77 145 136 90 58 4.8 8 0.9 2.8 1 15Z1B04-1000 25.2 86 45-65 16 178 73 87 180 166 113 55 4.8 8 1.8 4.4 1 16Z1B04-1000 34.7 99 45-65 16 178 88 100 178 166 113 68 4.8 8 2 5.9 1 17Z1B04-1000 44.1 123 45-65 16 219 101 115 215 201 136 73 7 12 2.8 8.4 1 18Z1B04-1000 52.5 126 45-65 35 219 111 120 220 201 136 81 7 12 3.2 10 1 19Z1B04-1000 63 142 45-65 35 219 121 135 220 201 136 91 7 12 3.7 12 1 20Z1B04-1000 79 168 45-65 35 219 121 150 220 201 136 91 7 12 3.8 12 1 21Z1B04-1000 95 194 45-65 M8 267 109 155 207 249 176 82 7 12 6.3 15.6 2 22Z1B04-1000 121 210 45-65 M8 291 129 185 215 273 185 97 10 18 6.5 19.3 2 23Z1B04-1000 158 240 45-65 M8 291 129 200 215 273 185 97 10 18 8.5 22 2 24Z1B04-1000 189 310 45-65 M10 316 153 225 235 292 200 113 10 16 8 24.8 2 25Z1B04-1000 221 328 45-65 M10 316 153 222 234 292 200 113 10 16 6.2 25 2 26Z1B04-1000 263 400 45-65 M10 352 145 210 266 328 224 105 10 16 10 31.6 2 27Z1B04-1000 315 440 45-65 M10 352 145 230 265 328 224 106 10 16 9 34 2 28Z1B04-1000 390 559 45-65 M10 388 150 245 295 364 248 112 10 16 11.7 41.5 2 29Z1B04-1000 485 620 45-65 M12 412 155 250 315 388 264 116 10 16 13 49.3 2 30Z1B04-1000 600 650 45-65 M12 412 174 270 315 388 264 132 10 16 13 57.7 2 Mains choke 3-phases 690 V AC (U max = 760 V), 50/60 Hz f Netz Ø B H H 1 T a 1 a 2 a 3 d 1 d 2 Weight Part-No. [A] [W] [Hz] [mm 2 ] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] Cu [kg] m [kg] Fig. 28Z1B06-1000 240 480 45-65 M10 412 156 236 312 388 264 116 10 16 13 45 2 29Z1B06-1000 295 520 45-65 M10 412 156 236 312 388 264 116 10 16 20 50 2 30Z1B06-1000 370 570 45-65 M10 412 174 260 322 388 264 123 10 16 18 62 2 31Z1B06-1000 405 550 45-65 M12 480 174 260 370 450 316 123 12 20 24 55 2 5 T d2 d1 B a2 a1 a3 H H1 Fig. 1 Fig. 2
KEB COMBILINE mains-side Harmonic filters are the new innovative KEB solution for reducing mains harmonics. Planning is as easy as for a mains choke, which can already be included in the planning phase for the electrical switching system and which enables compliance with many international standards. EN 61000-3-2; up to 16 A EN 61000-3-4 EN 61000-3-12; 16 A up to 75 A IEEE 519-1992 (USA) G5/4 Engineering Recommendation (GB) EN 12015 (Standard for lifts, escalators AS 2279 (Australia) COP, supply rules (Hong Kong) and passenger conveyors, Europe) Quality of Electric Energy Supply, Harmonics in Public Supply Network (China) Input Output Voltage and current inverter side A new innovative internal structure results in mains-friendly energy consumption with excellent application characteristics. In short, the KEB COMBILINE harmonic filter is universally suited for all types of consumers with B6 inputs. 6 It offers the following unique features: compact design no tendency to oscillate with dynamic load cycles lower voltage loss as compared to mains chokes allows multiple parallel consumers per unit optimised configuration for generators in isolated operations protection for drives in soft and overshooting mains increased service life for DC-Bus capacitors does not require additional compensation facilities when equipment is modernised or expanded d1 a2 a1 B d2 T a3 H H1 General technical data Protection rating IP20, open types Cooling Convection max. leakage current 0 ma (with option HF filter 7 ma) Efficiency factor > 98 % Overload 150 % - 60 sec. Temperature Storage -25...70 C Operation -10...45 C Climate category 3K3 (EN 60721-3-3) Environment (IEC 664-1) Pollution level 2 Vibration / Shock Germanischer Lloyd, EN 50155 Installation position standing / lying with capacitor positioned below choke Technical principles EN 61558-2-20, VDE 0160 in preparation UL-, cul- approval
Harmonic filter Harmonic filter 3-phases 400 V AC (U max = 440 V), 50 Hz - THDI < 15 % / PWHD < 39 % P FU Ø B H H 1 T a 1 a 2 a 3 d 1 d 2 Weight Part-No. [A] [kw] [W] [mm 2 ] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] Cu [kg] m [kg] 07Z1C04-1001 2.4 0.75 40 4 148 69 134 163 136 90 51 4.8 8 0.7 2.6 10Z1C04-1001 6.1 2.2 65 4 178 75 128 168 166 113 56 4.8 8 1.6 4.8 12Z1C04-1001 10 4 90 4 175 90 145 220 168 113 75 4.8 10 2.2 6.8 13Z1C04-1001 12.6 5.5 105 4 219 102 155 233 202 136 73 7 12 3.5 8.7 14Z1C04-1001 17.3 7.5 135 4 243 105 185 260 225 145 75 7 12 4.2 11.5 15Z1C04-1001 25.2 11 165 16 267 109 174 280 249 176 78 7 12 5.8 16.3 16Z1C04-1001 34.7 15 210 16 291 130 205 275 275 185 97 10 18 7.6 22.6 17Z1C04-1001 44.1 18.5 255 16 291 140 215 280 275 185 110 10 18 9.3 27 18Z1C04-1001 52.5 22 295 35 316 152 256 300 292 200 112 10 16 11.2 33 19Z1C04-1001 63 30 360 35 316 163 260 297 292 200 124 10 16 12.7 38.7 Harmonic filter 3-phases 400 V AC (U max = 440 V), 50 Hz - THDI < 8 % / PWHD < 15 % P FU Ø B H H 1 T a 1 a 2 a 3 d 1 d 2 Weight Part-No. [A] [kw] [W] [mm 2 ] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] Cu [kg] m [kg] 09Z1C04-1000 4.3 1.5 60 4 178 90 142 170 166 113 71 4.8 8 1.4 5.8 12Z1C04-1000 10 4 110 4 219 121 170 233 201 136 91 7 12 3.4 11.5 13Z1C04-1000 12.6 5.5 130 16 243 115 195 230 225 144 86 7 12 4.2 13.4 14Z1C04-1000 17.3 7.5 180 16 291 118 192 256 273 185 86 10 18 6.6 18.3 15Z1C04-1000 25.2 11 190 16 291 140 214 257 273 185 106 10 18 9 25.5 16Z1C04-1000 34.7 15 260 16 352 145 240 324 328 224 106 10 16 15 38.5 17Z1C04-1000 44.1 18.5 270 35 352 170 261 324 328 224 131 10 16 15 47.1 18Z1C04-1000 52.5 22 285 35 352 185 260 337 328 224 147 10 16 15 54.6 19Z1C04-1000 63 30 420 35 352 193 355 326 328 224 155 10 16 22 63 20Z1C04-1000 79 37 430 50 388 183 296 360 364 248 144 10 16 23.5 72.6 21Z1C04-1000 95 45 520 50 412 193 320 405 388 264 153 10 16 29.5 96 22Z1C04-1000 121 55 590 50 412 214 378 404 388 264 175 10 16 36 107.7 23Z1C04-1000 158 75 785 95 480 245 416 475 450 316 193 12 20 42.2 162 24Z1C04-1000 189 90 950 95 552 241 515 522 516 356 184 14.5 24 50.8 182.5 25Z1C04-1000 221 110 1145 150 552 275 550 520 525 360 215 14.5 24 60.4 244 26Z1C04-1000 263 132 1360 150 552 294 567 545 516 356 236 14.5 24 63.4 241.5 27Z1C04-1000 315 160 1480 240 552 315 635 550 515 355 255 14.5 24 72.9 294 28Z1C04-1000 390 200 1650 2x150 651 264 530 629 620 460 214 14.5 24 98.2 353 29Z1C04-1000 485 250 1800 2x240 660 350 633 620 620 460 288 14.5 24 126.4 513 7 Harmonic filter 3-phases 480 V class (U max = 528 V), 60 Hz - THDI < 8 % / PWHD < 15 % P FU Ø B H H 1 T a 1 a 2 a 3 d 1 d 2 Weight Part-No. [A] [HP] [W] [mm 2 ] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] Cu [kg] m [kg] 19Z1C05-1000 46 40 750 M8 352 169 175 325 328 224 128 10 16 16 44.5 20Z1C05-1000 57 50 900 M8 352 185 220 325 328 224 147 10 16 15 55 21Z1C05-1000 69 60 1100 M8 352 193 230 326 328 224 155 10 16 15 64 22Z1C05-1000 90 75 1500 M8 480 200 240 400 468 344 151 10 16 21 93 23Z1C05-1000 115 100 1900 M10 492 202 250 450 468 344 164 10 16 25 106 24Z1C05-1000 150 125 2400 M10 645 248 310 520 626 466 188 14 24 26 165 25Z1C05-1000 190 150 2300 M10 662 248 310 525 626 466 190 14 24 40 180 27Z1C05-1000 220 200 3100 M10 662 278 315 515 626 356 218 14 24 40 230 28Z1C05-1000 300 250 3500 M12 662 298 360 525 626 466 240 14 24 53 258 29Z1C05-1000 360 300 4200 M16 662 318 380 535 626 466 258 14 24 55 280 30Z1C05-1000 410 350 4400 M16 645 330 400 520 626 466 258 14 24 58 285
KEB COMBILINE mains-side Standard HF-Filter are filters which are installed on the mains side for the purpose of complying with statutory limits for mains-bound highfrequency interference. The filters consist of an LC grid which ensures maximum mismatch between the high-frequency interference source and the mains. Mechanically adapted for the KEB COMBIVERT F5 frequency inverters, these filters have been designed for mains-side interference suppression with especially high attenuation over a wide frequency range. These all-purpose filters can be used with all available switching frequencies. They also offer the advantage of increasing the interference resistance of connected frequency inverters. In the range up to 75 kw, the filters are mechanically designed as footprint filters for KEB COMBIVERT F5 inverters, and do not utilise additional switch cabinet space. Starting at 90 kw, the filters are installed in space-saving side-mount enclosures with minimal installation volumes. Low-leakage current IT-HF filters supplement the E5 series of footprint filters for applications with optimised leakage currents in the drive system and installations in IT networks. The filters in the adapted enclosure design for KEB COMBIVERT F5 are designed with a small capacitive percentage and feature very low leakage currents with reduced motor cable lengths. Scan Graph dbµv 80.0 70.0 60.0 50.0 EN 61800-3 Class C1 QP AV 40.0 30.0 20.0 Residential and office areas Scan Graph 8 dbµv 100.0 10.0 90.0 0.0 80.0 150 khz 1MHz 10MHz 30MHz EMC characteristic limit 70.0 60.0 EN 61800-3 Class C2 QP AV 50.0 40.0 30.0 20.0 Industrial environments 10.0 0.0 150 khz 1MHz 10MHz 30MHz EMC characteristic limit a1 a3 H T a4 B
Standard HF filter EMC-Filter 1-phase 230 V AC (U max = 264 V), 50/60 Hz ±10 % I ab Suppression degree / Ø Footprint B H T a 1 a 2 a 3 a 4 Weight Part-No. [A] [W] [ma] Motor cable length [mm 2 ] Housing [mm] [mm] [mm] [mm] [mm] [mm] [mm] m [kg] 07E5T60-0061 12 5 3.4 C1 / 10 m 4 B 88 249 40 240 210 - - 0.9 10E5T60-0001 22 20 12 C1 / 30 m 4 B 88 249 40 240 210 - - 0.9 10E5T60-0002 22 22 12 C1 / 30 m 4 D 88 285 40 275 240 - - 0.9 EMC-Filter 3-phases 400/480 V AC (U max = 528 V), 50/60 Hz ±10 % I ab Suppression degree / Ø Footprint B H T a 1 a 2 a 3 a 4 Weight Part-No. [A] [W] [ma] Motor cable length [mm 2 ] Housing [mm] [mm] [mm] [mm] [mm] [mm] [mm] m [kg] 09E5T60-1001 5.3 15 15 C1 / 30 m 1.5 A 75 191 40-175 - - 1 10E5T60-1001 8 7 15 C1 / 30 m 4 B 88 249 40 240 210 - - 1.3 10E5T60-1002 8 7 15 C1 / 30 m 4 D 88 285 40 275 240 - - 1.3 12E5T60-1001 16 12 20 C1 / 30 m 4 B 88 249 40 240 210 - - 1.3 13E5T60-1001 16 12 20 C1 / 30 m 4 D 88 285 40 275 240 - - 1.3 14E5T60-1001 22 16 20 C1 / 30 m 4 D 88 285 50 275 240 - - 1.5 14E4T60-1001 20 14 17 C1 / 30 m 6 E 132 352 50 335 275-100 1.5 15E5T60-1001 30 21 17 C1 / 30 m 10 E 132 352 50 335 275-100 1.5 16E5T60-1001 43 30 10 C1 / 30 m 10 E 132 352 50 335 275-100 2.5 17E5T60-1001 50 14 11 C1 / 30 m 10 G 181 415 56 400 330-150 3.2 18E5T60-1001 65 20 30 C1 / 30 m 25 G 181 415 65 400 330-150 5.1 18E5T60-1002 65 20 30 C1 / 30 m 25 H 300 445 66 420 330 250 5.1 19E5T60-1001 90 26 16 C1 / 30 m 25 H 300 445 66 420 330-250 6 20E5T60-1002 100 30 15 C1 / 30 m 50 H 300 445 75 420 330 250 8 20E4T60-1001 110 60 48 C1 / 30 m 50 R 64 419 270 385 - - 200 8.5 22E4T60-1001 150 60 48 C1 / 30 m 50 R 64 419 270 385 - - 200 10 23E4T60-1001 180 40 45 C1 / 30 m 50-110 474 240 414 - - 200 15 25E4T60-1001 250 50 55 C1 / 30 m 70-240 630 110 574 - - 200 16 27E4T60-1001 330 75 60 C1 / 30 m 95-110 630 240 574 - - 200 18 26E4T60-1001 300 50 60 C2 / 30 m M10-260 385 115 240-120 235 18.5 28E4T60-1001 410 50 60 C2 / 30 m M10-260 385 115 240-120 235 18.5 30E4T60-1001 650 50 60 C2 / 30 m M10-260 390 135 240-120 255 21.5 32E4T60-1001 1000 90 20 C2 / 30 m M10-280 458 185 290-270 130 33.5 9 a2 a1 H a4 T B
KEB COMBILINE mains-side 10 Low-leakage current IT-HF filters In insulated grids, insulation resistance is continuously monitored against ground. During this monitoring process, the discharge resistors used in the filters falsify this measurement and they must be suppressed during normal operations. The space-saving IT-HF filters meet this requirement internally and also offer small leakage currents in addition to providing the appropriate damping. The enclosure design has been implemented so as to be compatible with the KEB COMBIVERT F5 inverters, depending on its function as a footprint or book-style side-mount version. Low-leakage current IT-HF filters 3-phases 400/480 V AC (U max = 528 V), 50/60 Hz ± 10% I ab Suppression degree / Ø Footprint B H T a 1 a 2 Weight Part-No. [A] [W] [ma] Motor cable length [mm²] Housing [mm] [mm] [mm] [mm] [mm] m [kg] 10E5T60-10F1 8 7 4.5 C1 / 10 m 4 B 88 249 40 240 210 1.3 10E5T60-10F2 8 7 4.5 C1 / 10 m 4 D 88 285 40 275 240 1.3 12E5T60-10F1 14 12 4.5 C1 / 10 m 4 B 88 249 40 240 210 1.3 13E5T60-10F1 16 12 4.5 C1 / 10 m 4 D 88 285 40 275 240 1.3 14E5T60-10F1 20 14 4 C1 / 10 m 6 D 132 352 50 335 275 1.5 14E5T60-10F2 22 16 5 C1 / 10 m 4 D 88 285 50 275 240 1.5 15E5T60-10F1 30 21 4 C1 / 10 m 6 E 132 352 50 335 275 1.5 15E5T60-10F2 32/50 %ED 16 5 C1 / 10 m 10 D 88 285 50 275 240 1.5 16E5T60-10F1 43 30 8 C1 / 10 m 10 E 132 352 50 335 275 2.5 17E5T60-10F1 50 14 11 C1 / 10 m 10 G 181 415 56 400 330 3.2 17E5T60-10F2 50 14 10 C1 / 10 m 10 G 181 415 56 400 330 3.2 18E5T60-10F1 70 15 12 C1 / 10 m 25 H 300 445 66 420 330 5.1 18E5T60-10F2 65 20 7 C1 / 10 m 25 G 179.5 424 64.5 390 330 5.1 19E5T60-10F2 90 26 7 C1 / 10 m 25 H 300 445 66 420 330 6 20E5T60-10F1 100 30 6 C1 / 10 m 25 R 300 445 75 420 330 8 22E4T60-1051 150 60 48 C1 / 30 m 50 R 270 419 64 385 10 23E5T60-1051 165 60 48 C1 / 30 m 50-270 419 64 385 16 25E4T60-1051 250 50 55 C1 / 30 m 70-110 630 240 598 16 26E4T60-1051 300 50 60 C2 / 30 m M10-260 385 115 240 18.5 28E4T60-1051 410 50 60 C2 / 30 m M10-260 385 115 240 18.5 30E4T60-1051 650 60 60 C2 / 30 m M10-260 390 135 240 21.5 a2 T a1 H B
Radio interference suppression filters Enclosure system for COMBIVERT F5 The mechanical configuration of the HF filters has been designed for minimal space requirements in the switch cabinet and directly optimised for the enclosure design of the KEB COMBIVERT F5 inverter and servo drive series. Mechanical designs configured as footprint versions also offer directly mountable enclosures for powers up to 75 kw, which require no or only minimally larger areas on the mounting plate and provide extensive ground connections with the accessory kit for the shield clamps. More extensive enclosure requirements can be implemented with customer-specific versions. Appropriate for the footprint versions up to housing size H, the shield connection kits provide mechanically and electrically optimum ground connections for the control and power lines for KEB COMBIVERT F5: Shield connection kits Part-No. Housing Power circuit Control circuit B B0F5T88-0001 integrated D B0F5T88-0001 integrated E E0F5T88-0001 integrated G G0F5T88-0001/2 G0F5T88-0005 H H0F5T88-0001/2 H0F5T88-0005 Adjusted for the higher weights and dimensions of the drive controllers, the mechanical HF filter is designed as a book-style side-mount version starting at powers of 90 kw. The filters reach their optimum effect if mounted with shielded connection wires directly beside the devices on EMC-appropriate and conductive surfaces. 11
KEB COMBILINE mains-side Central HF filters, E6 series The KEB E6 high-frequency (HF) filter can be used as central switch cabinet filters, collection filters and for the suppression of individual devices. Large rated voltage range 0-550 V. Rated currents from 12-330 A, in eight sizes. Compact design in book form with small footprint. High saturation resistance. Shielded motor cable lengths up to 100 m and 500 m. An especially wide damping area due to newly developed filter components. With respect to operations with frequency inverters, the filters have been designed for a low leakage current. With the same applications, the leakage current will be reduced to as low as 1/10 as compared to standard filters. Operation at AC/DC sensitive RCD s with small triggering level 30/300 ma for people and fire protection. High short overload capacity. Three-wire input HF filters for connecting 3-phase consumers Four-wire HF filters for connecting single and 3-phase consumers (3-phase plus neutral wire) 12
Central HF filters, E6 series Three-wire HF-Filter 3-phases 400/480 V AC (U max = 550 V), 50/60 Hz ± 10 % I ab Suppression degree / Ø B H T a 1 a 2 Weight Part-No. [A] [W] [ma] Motor cable length [mm²] [mm] [mm] [mm] [mm] [mm] m [kg] 12E6T60-3000 12 8 <3 C1/ 50 m, C2/ 100 m 6 45 252 77 237 25 0.9 14E6T60-3000 22 14 <3 C1/ 50 m, C2/ 100 m 6 55 252 92 237 25 1.3 16E6T60-3000 43 18 <3 C1/ 50 m, C2/ 100 m 16 65 252 106 237 30 1.8 18E6T60-3000 65 27 <3 C1/ 50 m, C2/ 100 m 25 130 240 142 220 100 3.9 20E6T60-3000 100 54 <3 C1/ 50 m, C2/ 100 m 50 160 240 142 220 130 5 22E6T60-3000 150 80 <3 C1/ 50 m, C2/ 100 m 95 200 321 190 260 150 9 24E6T60-3000 200 100 <3 C1/ 50 m, C2/ 100 m 95 200 321 190 260 150 9.2 27E6T60-3000 330 160 <3 C2/ 100 m M10 250 516 194 320 200 22.5 Four-wire HF-Filter 3-phases 400/480 V AC (U max = 550 V), 50/60 Hz ± 10 % I ab Suppression degree / Ø B H T a 1 a 2 Weight Part-No. [A] [W] [ma] Motor cable length [mm²] [mm] [mm] [mm] [mm] [mm] m [kg] 14E6T60-4100 22 20 <3 C2/ 300 m 6 60 275 150 258 106 2.1 16E6T60-4100 43 22 <3 C2/ 300 m 10 70 330 160 288 106 3.2 18E6T60-4100 65 50 <3 C2/ 300 m 16 80 385 200 335 170 4.7 20E6T60-4100 100 80 <3 C2/ 300 m 25 91 458 240 395 200 6.7 22E6T60-4100 150 100 <3 C2/ 300 m 50 120 466 240 395 200 9.7 Scan Graph dbµv 80.0 a2 70.0 60.0 50.0 40.0 30.0 20.0 13 10.0 0.0 150 khz 1MHz 10MHz 30MHz EMC characteristic a1 H Ableitstrom in ma AC/DC sensitive RCCB (residential current circuit breaker) Standard HF filter E6-HF-filter T Frequenz in Hz B Comparison leakage currents
KEB COMBILINE Advisory and testing EC Directive 2004/108/EC requires all equipment manufacturers to design the installation of electrical systems in compliance with EMC legislation. In many cases, this means that individual CE-labelled components must be inspected for their interaction in the equipment or machine. For this purpose, KEB offers a service that includes advisory services and the testing of electrical equipment. Our extensive experience in the development and application of drive controllers in a variety of different industrial areas, combined with modern mobile measurement devices, are the ideal prerequisites for rapid on-site assistance. The advantages are easy to see: No expensive investments into measurement devices, buildings, installations and staff No training for complex standards Standards-appropriate on-site measurements Extensive measurement protocol Support already provided during development phase Advisory services for practical wiring Benefit from long-standing KEB experience Cost-effective 14 KEB provides security! Drives, EMC advisory and EMC filters with d
Comprehensive EMC services 1. In-house absorber building Transient emissions / interference pursuant to EN 61800-3 Physical dimensions 3 m test section 2000 x 2000 mm quiet zone Test object weight up to 1 tonne For connected loads to 60 kva 230/400/480/690 V 2. Installation advisory services for optimising electrical switching systems 3. EMC measurements on location: conducted measurement and determination of transient emissions 15 eliveries from one source.
KEB COMBILINE motor-side Motor chokes present a cost-effective option for reducing the voltage rise rate du/dt in order to avoid the premature ageing of the coil insulation in AC motors. increase total inductance at output. reduce current ripples. reduce the rise rate of the edges (dv/dt) of the IGBT increase the service life of motor coils. reduce the peak value of the current and reduce the stress on IGBTs in inverters. and are suitable for applications with long motor cables (> 15 m) The basic series is designed for applications with output frequencies of up to 100 Hz. Additional versions are available for frequency ranges 200 Hz to 1600 Hz as customer-specific designs. 16
Motor chokes Motor choke 3-phases 400 V AC (U max = 550 V), 100 Hz L Ø B H H 1 T a 1 a 2 a 3 d 1 d 2 Weight Part-No. [A] [mh] [W] [mm²] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] Cu [kg] m [kg] 05Z1F04-1010 1.3 11.3 8 4 100 55 H 121 80 40 4.8 8 0.2 0.8 07Z1F04-1010 2.6 5.6 15 4 100 55 H 121 80 40 4.8 8 0.2 1.0 09Z1F04-1010 4.1 3.18 15 4 100 53 H 121 80 37 4.8 8 0.4 1.1 10Z1F04-1010 5.8 2.06 17 4 100 63 H 121 80 47 4.8 8 0.4 1.4 12Z1F04-1010 9.5 1.26 24 4 148 68 H 145 136 90 47 4.8 8 0.5 1.8 13Z1F04-1010 12 1 31 4 148 78 H 145 136 90 59 4.8 8 0.5 2.5 14Z1F04-1010 16.5 0.72 37 4 148 78 H 145 136 90 59 4.8 8 0.6 2.8 15Z1F04-1010 24 0.5 47 10 178 72 H 178 166 113 53 4.8 8 1.3 3.9 16Z1F04-1010 33 0.36 54 10 178 100 H 180 166 113 68 4.8 8 1.5 5.9 17Z1F04-1010 42 0.28 65 16 219 100 105 215 201 136 70 7 12 1.9 6.6 18Z1F04-1010 50 0.24 65 35 219 110 110 220 201 136 81 7 12 2.4 8.5 19Z1F04-1010 60 0.2 67 35 219 121 130 225 201 136 91 7 12 2.6 10.1 20Z1F04-1010 75 0.16 79 35 243 115 130 243 225 156 85 7 12 3.6 12 21Z1F04-1010 90 0.13 105 M8 (35) 267 109 155 207 249 176 78 7 12 3.6 15.6 22Z1F04-1010 115 0.1 137 M8 (50) 291 129 185 215 273 185 97 10 18 3.6 15.5 23Z1F04-1010 150 0.08 170 M8 (70) 291 130 183 216 273 185 97 10 18 5.1 17 24Z1F04-1010 180 0.07 210 M10(70) 316 153 225 233 292 200 113 10 16 5.2 24 25Z1F04-1010 210 0.06 270 M10(70) 316 153 196 234 292 200 113 10 16 5.8 23.4 26Z1F04-1010 250 0.05 380 M10(120) 352 145 230 270 328 224 105 10 16 8.2 29.8 27Z1F04-1010 300 0.04 420 M10(150) 352 147 235 272 328 224 110 10 16 12.0 35.5 28Z1F04-1010 370 0.03 450 M10(150) 388 151 245 300 364 248 112 10 16 10.3 40 29Z1F04-1010 460 0.03 550 M12(185) 412 155 245 325 388 264 116 10 16 11.0 48.2 17 T d2 H1 H a3 d1 a2 a1 B
KEB COMBILINE motor-side Sinusoidal filters are low-pass filters that filter out the switching frequency from the PWM (pulse width modulation) - output signal of the inverter. Sinusoidal voltage with a small ripple occurs at the output, which results in a sinusoidal motor current. This is why the use of sinusoidal filters at the output is not associated with the supplementary losses in the motor s stator and rotor which otherwise occur with inverter operations. KEB sinusoidal filters reduce supplementary losses in the motor during direct inverter operations. This is a particular requirement for older motors that are not designed for inverter operations, as well as used specialty motors and medium-frequency motors. reduce discharge currents driven by pulse frequency in the case of long cable lengths. The sinusoidal output voltages between the phases and the significant du/dt reduction in the voltages phase to ground reduce the capacitive currents. Sinusoidal filters are recommended for up to 500 m motor cable lengths, depending on the type of drive. Lengths exceeding 500 m require an additional EMC level. increase the service life of motor insulation. High du/dt at the output of the frequency inverter puts stress on the motor coils. Combined with long cable lengths, it is possible that the high rise of voltage (du/dt) and non-adjusted impedances of inverter, motor cable and motor result in overstressing. Their peaks may increase to double the value of the DC link voltage (approx. 1600 V). The sinusoidal filter reduces the PWM signal of the frequency inverter to sinusoidal sizes, preventing overstressing and a smaller rise of voltage at the motor coil. 18 reduce bearing currents in the motor. The filter reduces the high-frequency portions in the output voltage of the inverter, which in turn reduces the high-frequency portions of the voltage at the motor so as to result in a reduction of bearing currents. reduce motor noise, which is lessened due to the sinusoidal voltage between the phases. reduce high-frequency transient emissions and improve the entire EMC load on the equipment. Improve motor efficiency available solutions Sinusoidal filter xxz1g04-1000 to 50/100 Hz output frequency Sinusoidal filter xxz1g04-1001 to 200 Hz output frequency Sinusoidal filter xxz1g04-1003 to 800 Hz output frequency Sinusoidal filter xxz1g04-1004 to 1200/1600 Hz output frequency
Sinusoidal filter Sinusoidal filter 3-phases 400 V AC (U max = 500 V), f max 100 Hz P FU I I max. f S B H T a 1 a 2 a 3 d 1 d 2 Ø Weight [kw] Part-No. [A] [A] [W] [khz] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm²] Cu [kg] m [kg] 0.37 05Z1G04-1000 1.3 2.3 25.9 4-16 100 110 120 80-96 4.8 8 4 0.3 1.1 0.75 07Z1G04-1000 2.6 4.7 27.9 4-16 100 125 135 80-110 4.8 8 4 0.4 1.7 1.5 09Z1G04-1000 4.1 7.4 36.7 4-16 148 132 150 136 90 49 4.8 8 4 0.9 2.5 2.2 10Z1G04-1000 5.8 10.4 42.4 4-16 148 143 142 136 90 60 4.8 8 4 1 3.1 4 12Z1G04-1000 9.5 17 48.2 4-16 178 125 167 166 113 56 4.8 8 4 1.8 4.5 5.5 13Z1G04-1000 12 21.6 67.2 4-16 178 145 178 166 113 71 4.8 8 10 2.1 6.4 7.5 14Z1G04-1000 16.5 29.7 86.8 4-16 219 145 207 201 136 74 7 12 10 2.9 8.2 11 15Z1G04-1000 24 36 95 4-16 243 180 225 225 156 79 7 12 10 3.8 11.5 15 16Z1G04-1000 33 49.5 130.2 4-16 267 172 260 249 176 81 7 12 16 5.5 15.6 18.5 17Z1G04-1000 42 63 136.6 4-16 291 197 272 273 185 100 10 18 35 7.4 21.8 22 18Z1G04-1000 50 75 189.1 4-16 291 221 277 273 185 113 10 18 35 8.5 27.7 30 19Z1G04-1000 60 90 190.3 4-16 316 230 305 292 200 116 10 16 35 10.7 32.5 37 20Z1G04-1000 75 112 201.6 4-16 352 265 332 328 224 135 10 16 35 11 41.5 45 21Z1G04-1000 90 135 205.2 4-16 352 282 358 328 224 148 10 16 50 13.8 48.6 55 22Z1G04-1000 115 172 230 4-16 388 288 395 364 248 148 10 16 95 20 67.2 75 23Z1G04-1000 150 225 265 4-16 412 317 416 388 264 138 10 16 M10 (120) 26 72.5 90 24Z1G04-1000 180 270 270 4-16 412 358 412 388 264 184 10 16 M10 (120) 34 99.6 110 25Z1G04-1000 210 263 335 4-16 480 340 467 450 316 157 12 20 M12 (185) 36 120.5 132 26Z1G04-1000 250 313 480 4-16 480 365 464 450 316 170 12 20 M12 (185) 42 129 160 27Z1G04-1000 300 375 503 4-16 480 390 470 450 316 195 12 20 M12 (185) 47 156 200 28Z1G04-1000 370 463 600 2-16 552 575 526 516 356 244 14.5 24 M16 (300) 83 272 250 29Z1G04-1000 460 575 630 2-16 555 600 545 516 356 262 14.5 24 M16 (300) 80 275 315 30Z1G04-1000 570 712 950 2-16 660 501 645 620 460 214 14.5 24 2xM16 (300) 115 355 355 31Z1G04-1000 630 787 1550 2-16 660 560 645 620 460 250 14.5 24 2xM16 (300) 126 400 400 32Z1G04-1000 710 887 1750 2-16 660 618 645 620 460 270 14.5 24 2xM16 (300) 130 420 Please note: The sinusoidal filters have been designed for permissible switching and output frequency areas - values that deviate from this range will cause damage to the filters. 19 T d2 H a3 a2 a1 B d1
KEB COMBILINE motor-side Sinusoidal filter 3-phases 400 V AC (U max = 500 V), f max 200 Hz P FU I I max. P v f S B H T a 1 a 2 a 3 d 1 d 2 Ø Weight [kw] Part-No. [A] [A] [W] [khz] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm²] Cu [kg] m [kg] 0.37 05Z1G04-1001 1.3 2.3 7.5 4-16 100 110 120 80-95 4.8 8 4 0.2 0.75 0.75 07Z1G04-1001 2.6 4.7 10 4-16 100 125 135 80-110 4.8 8 4 0.5 1.6 1.5 09Z1G04-1001 4.1 7.4 20 4-16 148 130 160 136 90 49 4.8 8 4 0.8 2.2 2.2 10Z1G04-1001 5.8 10.4 35 4-16 148 141 142 136 90 59 4.8 8 4 1 3.2 4 12Z1G04-1001 9.5 17 42 4-16 178 140 195 166 113 55 4.8 8 4 1.8 4.3 5.5 13Z1G04-1001 12 21.6 48 4-16 178 153 191 166 113 70 4.8 8 4 2.1 6.5 7.5 14Z1G04-1001 16.5 29.7 60 4-16 219 148 205 201 136 73 7 12 16 2.7 7.6 11 15Z1G04-1001 24 36 80 4-16 243 188 245 225 156 75 7 12 16 3.8 11.5 15 16Z1G04-1001 33 49.5 120 4-16 291 190 260 273 185 91 10 18 16 4.2 15 18.5 17Z1G04-1001 42 63 150 4-16 291 198 275 273 185 99 10 18 35 6.3 20.2 22 18Z1G04-1001 50 75 160 4-16 291 225 280 273 185 115 10 18 35 6.7 25 30 19Z1G04-1001 60 90 165 4-16 316 235 300 292 200 128 10 16 35 10 34.3 37 20Z1G04-1001 75 112 170 4-16 325 224 320 328 224 135 10 16 35 11 37 45 21Z1G04-1001 90 135 180 4-16 325 250 380 328 224 135 10 16 50 12 43 55 22Z1G04-1001 115 172 186 4-16 388 268 425 364 248 149 10 16 95 20 66.5 75 23Z1G04-1001 150 225 190 4-16 388 300 440 364 248 155 10 16 95 22.1 87 90 24Z1G04-1001 180 270 193 4-16 412 342 450 388 264 160 10 16 M12 (185) 33 92.3 110 25Z1G04-1001 210 263 201 4-16 412 362 465 388 264 165 10 16 M12 (185) 35 120.3 132 26Z1G04-1001 250 313 218 4-16 480 348 470 450 316 168 12 20 M12 (185) 44 123.8 160 27Z1G04-1001 300 375 280 4-16 480 449 505 450 316 198 12 20 M12 (185) 47 147 200 28Z1G04-1001 370 463 290 4-16 552 506 515 516 356 205 14.5 24 M16 (300) 50 200 250 29Z1G04-1001 460 575 320 4-16 552 580 515 516 356 240 14.5 24 2xM12 (185) 63 230 20 Sinusoidal filter 3-phases 400 V AC (U max = 530 V), f max 800 Hz P FU I I max. P v f S B H T a 1 a 2 a 3 d 1 d 2 Ø Weight [kw] Part-No. [A] [A] [W] [khz] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm²] Cu [kg] [kg] 0.75 07Z1G04-1003 2.6 4.7 10 8-16 160 171 245 120-140 7 12 4 0.8 3.4 1.5 09Z1G04-1003 4.1 7.4 19 8-16 160 171 250 120-140 7 12 4 0.8 3.5 2.2 10Z1G04-1003 5.8 10.4 22 8-16 160 171 250 120-140 7 12 4 0.9 4 4 12Z1G04-1003 9.5 17 25 8-16 160 171 250 120-140 7 12 4 1.3 4.4 5.5 13Z1G04-1003 12 21.6 30 8-16 160 171 250 120-140 7 12 4 1.6 5.3 7.5 14Z1G04-1003 16.5 29.7 40 8-16 330 200 250 280-170 7 12 16 2.2 10.3 11 15Z1G04-1003 24 36 55 8-16 330 215 255 280-174 7 12 16 2.5 10.6 15 16Z1G04-1003 33 49.5 60 8-16 330 215 260 280-170 7 12 16 2.6 11 18.5 17Z1G04-1003 42 63 70 8-16 330 215 330 280-170 7 12 35 3.4 16.2 22 18Z1G04-1003 50 75 95 8-16 330 205 330 280-170 7 12 35 3.7 16.5 30 19Z1G04-1003 60 90 150 8-16 330 225 330 280-170 7 12 35 3.9 15.1 37 20Z1G04-1003 75 112 220 8-16 560 235 345 520 260 175 8.5 13.5 M8 (70) 5.5 22 45 21Z1G04-1003 90 135 240 8-16 560 235 345 520 260 175 8.5 13.5 M8 (70) 5.5 21.4 55 22Z1G04-1003 115 172 300 8-16 560 280 345 520 260 175 8.5 13.5 M8 (70) 6 21.7 75 23Z1G04-1003 150 225 390 8-16 560 305 395 520 260 175 8.5 13.5 M10 (120) 8 31.9 90 24Z1G04-1003 180 270 450 8-16 560 305 410 520 260 175 8.5 13.5 M10 (120) 8 33.4 110 25Z1G04-1003 210 263 520 8-16 625 330 410 584 292 220 9.5 24.5 M10 (120) 14 52 132 26Z1G04-1003 250 313 580 8-16 625 330 415 584 292 220 9.5 24.5 M10 (120) 15 53.8 160 27Z1G04-1003 300 375 680 8-16 416 535 460 359 179.5 480 9.5 24.5 M12 (185) 18 66.8 200 28Z1G04-1003 370 463 840 8-16 416 535 470 359 179.5 480 9.5 24.5 M16 (300) 26 75.6 250 29Z1G04-1003 460 575 1025 8-16 676 455 667 584 292 410 11 24.5 2x M12 (185) 35 126.5 315 30Z1G04-1003 570 713 1100 8-16 676 455 667 584 292 410 11 24.5 2x M12 (185) 40 145 355 31Z1G04-1003 630 787 1200 8-16 676 490 667 584 292 410 11 24.5 2x M16 (300) 45 155
Sinusoidal filter Sinusoidal filter 3-phases 400 V AC (U max = 530 V), f max 1200/1600 Hz P FU I I max. P v f S B H T a 1 a 2 a 3 d 1 d 2 Ø Weight [kw] Part-No. [A] [A] [W] [khz] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm] [mm²] Cu [kg] m [kg] 0.75 07Z1G04-1004 2.6 4.7 14 16 160 170 260 120-140 7 12 4 0.6 4 1.5 09Z1G04-1004 4.1 7.4 20 16 160 170 245 120-140 7 12 4 0.6 4.2 2.2 10Z1G04-1004 5.8 10.4 25 16 160 170 260 120-140 7 12 4 0.6 4.5 4 12Z1G04-1004 9.5 17 28 16 160 170 245 120-140 7 12 4 0.7 4.6 5.5 13Z1G04-1004 12 21.6 35 16 160 170 243 120-140 7 12 4 0.8 4.6 7.5 14Z1G04-1004 16.5 29.7 45 16 160 170 250 120-140 7 12 16 1.3 6 11 15Z1G04-1004 24 36 60 16 290 170 255 250-140 7 12 16 1.4 6.1 15 16Z1G04-1004 33 49.5 65 16 330 220 255 280-170 7 12 35 2.7 10.9 18.5 17Z1G04-1004 42 63 75 16 330 220 260 280-170 7 12 35 3 11.3 22 18Z1G04-1004 50 75 100 16 330 220 260 280-170 7 12 35 4.2 12.5 30 19Z1G04-1004 60 90 155 16 330 220 335 280-170 7 12 35 3.7 13.9 37 20Z1G04-1004 75 112 230 16 330 260 335 280-170 7 12 50 4.2 17 45 21Z1G04-1004 90 135 250 16 330 260 335 280-170 7 12 50 3.4 18 55 22Z1G04-1004 115 172 310 16 560 280 350 520 260 175 8.5 13.5 M8 (70) 6.7 21.5 75 23Z1G04-1004 150 225 400 16 560 280 360 520 260 175 8.5 13.5 M10 (120) 8.5 26.5 90 24Z1G04-1004 180 270 460 16 560 280 365 520 260 175 8.5 13.5 M10 (120) 9 27 110 25Z1G04-1004 210 263 540 16 560 285 376 520 260 175 8.5 13.5 M10 (120) 11 32.5 132 26Z1G04-1004 250 313 600 12 560 285 385 520 260 175 8.5 13.5 M12 (185) 12.2 43 160 27Z1G04-1004 300 375 700 12 625 340 410 584 292 220 9.5 24.5 M12 (185) 15 48 200 28Z1G04-1004 370 463 860 12 416 515 520 359 179.5 480 9.5 24.5 M16 (300) 18 62 250 29Z1G04-1004 460 575 1050 12 416 515 520 359 179.5 480 9.5 24.5 M16 (300) 20 68 315 30Z1G04-1004 570 713 1200 12 676 455 665 584 292 410 11 24.5 2xM12 (185) 29 108 355 31Z1G04-1004 630 787 1300 12 676 455 665 584 292 410 11 24.5 2xM16 (300) 28 114 Part-no. 07-25 maximum motor frequency 1600 Hz Part-no. 26-31 maximum motor frequency 1200 Hz 21
KEB COMBILINE combinations NHF-filters NHF filters combine a mains choke and HF filter in one enclosure. This means that the filter combines the advantages of the mains choke with those of the HF filter in one particularly compact assembly. This filter features high saturation resistance and small leakage currents, mechanically designed as ancillary filters. NHF-filter 3-phases 480 V AC (U max = 504 V), 50/60 Hz ± 10 % I P v I ab Suppression degree / Ø B H T a 1 d 1 d 2 Weight Part-No. [A] [W] [ma] Motor cable length [mm²] [mm] [mm] [mm] [mm] [mm] [mm] m [kg] 13E5T60-1011 14 56 15 C1 / 30 m 6 82 290 200 275-7 4 14E5T60-1011 19 55 23 C1 / 30 m 10 100 340 210 330 50 7 6.5 15E5T60-1011 27 82 20 C1 / 30 m 10 100 340 210 330 50 7 8 16E5T60-1011 37 86 21 C1 / 30 m 16 100 340 210 330 50 7 9 17E5T60-1011 47 110 25 C1 / 30 m 16 110 340 250 330 80 M6 12 18E5T60-1011 55 120 27 C1 / 30 m 35 110 340 250 330 80 M6 13 19E5T60-1011 66 120 25 C1 / 30 m 35 110 340 250 330 80 M6 16 L1 L2 L3 L1 L2 L3 NHF - filter PE L1 L2 L3 L1 L2 L3 Frequency inverter U V W U1 V1 W1 Sinusoidal filter U2 V2 W2 Motor 3 ~ PA PB Braking resistor d2 d1 T 22 H a1 B
I/O-filters I / O - fi l t e r s integrate the functionality of the mains-side HF filter and the motor-side dv/dt filter in one compact enclosure. A portion of the input filter that is configured with high damping at minimal leakage current, reduces conducted interference to limit value C1 pursuant to EN 61800-3. On the output side, configured for: - Output frequency 0 300 Hz passive output dv/dt filter with choke for limiting dv/dt stress The compact mechanical design enables space-saving installations with KEB COMBIVERT F5 and F6 series inverters as footprint versions and generally also as book-style side-mount versions. Brake resistors for emergency brakes can be mounted between the enclosure and the frequency inverter. E/A filters are designed for operations with cable lengths exceeding 30 m to approx. 200 m and protect connected motors against non-permissible high increases in voltage and non-permissible high peak voltages - both factors that negatively impact the service life of the coil insulation. I/O-filter 3-phases 480 V AC (U max = 530 V), 50/60 Hz ± 10 %, Motor frequency 0 300 Hz P FU I I ab P v Suppression degree / f Smax B H T a 1 a 2 Footprint f max Ø Weight [kw] Part-No. [A] [ma] [W] Motor cable length [khz] [mm] [mm] [mm] [mm] [mm] Housing [Hz] [mm²] m [kg] 2.2 10E5T60-10G1 8 10 29.5 C1 / 2x50 m 4 90 360 126 330 60 B/D 300 4 4.3 5.5 13E5T60-10G1 16.5 10 54.5 C1 / 2x50 m 4 90 360 126 330 60 B/D 300 4 4.3 7.5 14E5T60-10G1 22 10 65 C1 / 2x50 m 4 90 360 126 330 60 D 300 4 5.3 11 15E5T60-10G1 32 13 97 C1 / 2x50 m 4 130 360 85 330 100 E 300 10 6.5 15 16E5T60-10G1 42 13 106 C1 / 2x50 m 4 130 360 85 330 100 E 200 10 6.5 15 16E5T60-10G2 42 13 106 C1 / 2x50 m 4 170 412 131 400 140 G 200 16 7.3 22 18E5T60-10G1 50 20 117 C1 / 2x50 m 2 170 412 131 400 140 G 100 16 9.5 Active output dv/dt filters with choke for limiting dv/dt loads and an intermediate circuit feedback for reducing overstressing at the intermediate circuit level are available as customer-specific solutions for output frequency 0 1600 Hz. 23 T a1 H a2 B
Headquarters KEB AUTOMATION KG Südstraße 38 D - 32683 Barntrup Telefon +49 5263 401-0 Telefax 401-116 Internet: www.keb.de E-Mail: info@keb.de KEB Antriebstechnik GmbH Geared Motors Wildbacher Straße 5 D - 08289 Schneeberg Telefon +49 3772 67-0 Telefax 67-281 Internet: www.keb-drive.de E-Mail: info@keb-drive.de COMPANIES AUSTRIA KEB Antriebstechnik Austria GmbH Ritzstraße 8 A - 4614 Marchtrenk Tel: +43 7243 53586-0 Fax: +43 7243 53586-21 E-mail: info@keb.at Internet: www.keb.at CHINA KEB Power Transmission Technology (Shanghai) Co. Ltd. No. 435 QianPu Road Songjiang East Industrial Zone CN-201611 Shanghai, PR. China Tel: +86 21 37746688 Fax: +86 21 37746600 E-mail: info@keb.cn Internet: www.keb.cn FRANCE Société Française KEB Z.I. de la Croix St. Nicolas 14, rue Gustave Eiffel F - 94510 LA QUEUE EN BRIE Tel: +33 149620101 Fax: +33 145767495 E-mail: info@keb.fr Internet: www.keb.fr Further partners for GREAT BRITAIN KEB (UK) Ltd. Morris Close Park Farm Industrial Estate GB - Wellingborough NN8 6 XF Tel: +44 1933 402220 Fax: +44 1933 400724 E-mail: info@keb.co.uk Internet: www.keb.co.uk ITALY KEB Italia S.r.l. Unipersonale Via Newton, 2 I - 20019 Settimo Milanese (Milano) Tel: +39 02 3353531 Fax: +39 02 33500790 E-mail: info@keb.it Internet: www.keb.it JAPAN KEB - Japan Ltd. 15-16, 2 - Chome Takanawa Minato-ku J - Tokyo 108-0074 Tel: +81 33 445-8515 Fax: +81 33 445-8215 E-mail: info@keb.jp Internet: www.keb.jp RUSSIA KEB CIS ZAO Lesnaya str, house 30 Dzerzhinsky (MO) RUS - 140091 Moscow region Tel: +7 495 6320217 Fax: +7 495 6320217 E-Mail: info@keb.ru Internet: www.keb.ru USA KEB America, Inc 5100 Valley Industrial Blvd. South USA - Shakopee, MN 55379 Tel: +1 952 2241400 Fax: +1 952 2241499 E-mail: info@kebamerica.com Internet: www.kebamerica.com Representative offices Belgium Brazil Korea Sweden Spain Australia Belgium Bulgaria Czech Republic Denmark Egypt Greece Hungary India Indonesia Iran Israel Malaysia Morocco Netherlands New Zealand Pakistan Poland Portugal Romania Singapore Slovakia South Africa Spain Sweden Switzerland Taiwan Thailand Tunisia Turkey Uzbekistan under www.keb.de/en/contact/keb-worldwide.html KEB 0000000-5LIN / 02-2014 Subject to technical alterations!