Micro Metal Shell.050" ontact Spacing Specifications connectors are used in applications requiring highly reliable, extremely small, lightweight connectors with higher density contact configurations than available in traditional rectangular connectors. They are available in 8 shell sizes accommodating from 9 to 00 contacts, and special arrangements of power and coaxial contacts. These connectors are designed to meet the rapidly increasing demands for an environmental, high performance, rugged, moisturesealed microminiature connector. This connector employs size 4 MIROPIN TM /MIROSOKT TM contacts on.050 (.7) centers in a contact density identical to the standard MIRO connector series, but with these additional features: luminum shells to provide greater strength, prevent chipping, cracking or breaking, offer electromagnetic (MI) and RI shielding. Silicone elastomer compression interfacial seal to provide a moisture and humidity seal between each contact and between contacts and shell. STNR MTRILS N INISHS MHNIL TURS Shell 606T6 luminum alloy per oupling riction/jackscrews QQ00/8, yellow chromate/ Polarization Keystoneshaped shells cadmium, Type II, lass over electroless nickel per S ontact Spacing.050 (.7) MS6074, lass 4. enters Insulator Liquid rystal Polymer per MILM459, Type LP0 (900) lass filled diallyl phthalate per MILM4, Type S (7* and 4*4) Shell Styles No. of ontacts Plug and receptacle 9 thru 00 signal; 5 signal/ coaxial; 5 signal/ power; Polyphenylene sulfide per signal/5 coaxial; MILM459, Type ST40 (6*5) signal/5 power; 0 signal/0 coaxial; Polyester per MILM459, Type 0 signal/0 power; PT0 (0*0) 0 signal/4 coaxial; ontacts Mounting Hardware opper alloy, gold plate 00 Series stainless steel, passivate oaxial able 0 signal/4 power R 78/U Kit, Jackpost () items 00 Series stainless steel, passivate Wire Size #4 thru # W Washer Standard poxy 400 Series stainless stell, passivate Hysol 45/H56, color black or Hysol 498/H56, color green ontact Termination Multiple indent crimp Performance ata The table below summarizes the results of key tests performed in accordance with MILST44, where applicable. ata is applicable to standard connectors with standard termination. Variations may affect this data, so please consult customer service for further information on your requirements. Test ielectric Withstanding Method 00: Voltage 600 V at sea level 50 V at 70,00' altitude Insulation Resistance Method 00 Method riteria of cceptance Thermal Shock Method 00. ondition : 55 to +5 Physical Shock Method 004, ondition : 50 's, axes, 6 millisecond duration sawtooth pulse Vibration Method 005, ondition IV: 0 's, 0,000 Hz. hrs urability 500 cycles of mating and unmating, 500 PH max. Moisture Resistance Method 00, Type II, omit steps 7a & 7b Salt Spray Method 00, ondition : 48 hours ontact Resistance Method 00, ondition : (MILST0) t amps t milliamp ontact Retention Per MILTL85 No breakdown No breakdown 5,000 megohms minimum No physical damage No physical damage No loss of continuity > µsec No physical damage No loss of continuity > µsec No mechanical or electrical defects Insulation resistance > 00 megohms Shall be capable of mating and unmating, and meet contact resistance requirements 8 milliohms maximum 0 milliohms maximum 5 lb. minimum axial load 7
Micro Metal Shell.050" ontact Spacing How to Order or MILTL85 ordering information see pages 6 and 7 RoHS OMPLIN SRIS ONTT RRNMNTS ONTT TYP TRMINTION TYP TRMINTION O HRWR SHLL INISH MO OS R 5 P H 00 P XXX SRIS : (Size 900) Liquid rystal Polymer (LP) : (ombo Layout) iallyl Phthalate (P) ONTT TYP P Pin S Socket TRMINTION TYP H Harnessinsulated wire. L Soliduninsulated wire. S Solder pot to accept #6 W harness wire. (Not available with power contact arrangements.) HRWR M Military specification hardware, see page for military hardware codes. P Jackpost K Jackscrewstandard profile L Jackscrewlow profile loat mount No hardware standard.09 (.) dia. hole for sizes 95;.0 (.05) dia. hole for size 00..5 (.8) dia. mounting holes for sizes 95;.66 (4.) dia. hole for size 00..475 (.75) dia. hole for size 00 (Per MILTL85) TRMINTION O* (H) 00 8",7/4 strand,#6 W, MILW6878/4, Type Teflon, yellow. (H) 00 8", 7/4 strand, #6 W, MILW6878/4, Type Teflon, color coded to MILST68 System I. ONTT RRNMNTS 9557500 (standard) 65, 00, 7, 44 (coaxial) or combination of (L) /" uninsulated solid #5 6P5, 0P0, 7P, 4P4 (power) } coax and power W gold plated copper. (L) " uninsulated solid #5 W gold plated copper. SHLL INISH MO OS No Number (Standard cadmium/yellow chromate over nickel 74 lectroless nickel 7 old over nickel 4 Irridite/alodine 0 lack anodize *See page 79 and 8 for additional Termination codes. 8
Micro Metal Shell.050" ontact Spacing OTS or Non MilSpec or ommercial or Industrial Standard Wire Termination odes ontact rrangements annon Modification ode (Not MS) The following termination codes are listed for your information. or additional codes please refer to ppendix on page 79 and 8. ll wire lengths are minimum. Harness Type (H) Solid Uninsulated Type (L) #6 W per MILW6878/4, 7/4 strand, type Teflon, stranded. #5 W gold plated copper Length ll Yellow olor oded* Termination ode Length (76.) 6 (5.4) 8 (0.) 0 (54.0) (04.8) 8 (457.) 0 (508.0) 4 (609.6) 0 (76.0) 6 (94.4) 48 (9.) 7 (88.8) 0 (048.0) * avity # black H00 H09 H06 H09 H08 H00 H08 H009 H00 H0 H0 H07 H04 H07 H06 H04 H05 H00 H00 H0 H004 H005 H006 H048 H046 H04 L6 L56 L57 L9 L58 L L4 L L7 L6 L6 L0.5 (.8).50 (.8).90 (4.8).50 (6.5).75 (9.5).500 (.70).750 (9.05).000 (5.40).500 (8.0).000 (50.80).500 (6.50).000 (76.0) (ace View of Pin insert Use Reverse Order for Socket Side) Standard.05 (0.64) TYP..050 (.7) TYP. 4 5 4 5 6 7 8 4 5 6 7 8 9 0.04 (.09) 6 7 8 9 9 ontacts 9 0 4 5 4 5 6 7 8 9 0 5 ontacts ontacts 4 5 6 7 8 9 0 4 5 6 7 8 9 0 4 5 6 4 5 6 7 8 9 0 4 5 6 7 8 9 4 5 6 7 8 9 0 4 5 5 ontacts 7 8 9 0 4 5 6 7 8 9 0 ontacts 0 4 5 6 7 8 9 0 4 5 6 7 7 ontacts 4 5 6 7 8 9 0 4 5 6 7 8 9 0 4 5 6 7 8 9 0 4 5 6 7 8 9 40 4 4 4 44 45 46 47 48 49 50 5 4 5 6 7 8 9 0 4 5 6 7 8 9 0 4 5 6 7 8 9 0 4 5 6 7 8 9 40 4 4 4 44 45 46 47 48 49 50 5 5 ontacts 5 5 54 55 56 57 58 59 60 6 6 6 64 65 66 67 68 69 70 7 7 7 74 75 76 77 78 79 80 8 8 8 84 85 86 87 88 89 90 9 9 9 94 95 96 97 98 99 00 00 ontacts ontact identification numbers are for reference only and do not appear on insulator or connector body..0 oaxial.0 (8.).74 (8.4).460 (.68) 4 4 5 5 6 7 8 9 0 4 5 4 5 6 7 4 8 9 0 6 7 8 9 4 5 0 Size 5 Shell Micro contact 5 oax or 5 Power Size 5 Shell 5 Micro contact oax or Power 4 5 Size 5 Shell 0 Micro contacts 4 oax or 4 Power (Not MS).007 (0.8) 6 7 8 9 0 Size 00 Shell 0 Micro contact 0 oax or 0 Power 9
Micro Metal Shell.050" ontact Spacing OTS or Non MilSpec or ommercial or Industrial Shell imensions (onforms to MILTL85) Plug.0 (.79) TWO MT. HOLS.09 ±.00(. ±0.08).84 (7.).46 (0.57).86 (4.7).09 (.6) R..00 (5.08) Solder Pot Receptacle.0 (.79) TWO MT. HOLS.09 ±.00(. ±0.08).96 (7.5).49 (0.09).09 (.6) R..00 (5.08).98 (5.0) Solder Pot Receptacle (00 only) TWO MT. HOLS.0 ±.00(.05 ±0.08).49 (0.90).94 (0.0).98 (5.0).09 (.6) R. Pigtail termination.96 (7.5) Part Number y Shell Size 9P* 9S* 5P* 5S* P* P* 5P* 5S* P* S* 7P* 7S* 5P* 5S* 00P* 00S*.785 (9.94).785 (9.94).95 (.75).95 (.75).085 (7.56).085 (7.56).85 (0.0).85 (0.0).5 (.9).5 (.9).485 (7.7).485 (7.7).45 (6.45).45 (6.45).70 (55.).70 (55.).4 (8.48).40 (0.).484 (.9).55 (.97).64 (6.0).70 (7.8).74 (8.64).80 (0.7).884 (.45).95 (4.8).04 (6.6).0 (7.99).984 (4.99).05 (6.7).84 (5.5).508 (8.0) *dd lead type and length; see How To Order. +_.005 (0.).400 (0.6).400 (0.6).550 (.97).550 (.97).700 (7.78).700 (7.78).800 (0.).800 (0.).950 (4.).950 (4.).00 (7.94).00 (7.94).050 (6.67).050 (6.67).44 (6.6).44 (6.6).0 (7.87).0 (7.87).60 (9.4).60 (9.4).5 (8.9).5 (8.9).94 (0.0).94 (0.0).565 (4.5).565 (4.5).75 (8.6).75 (8.6).865 (.97).865 (.97).965 (4.5).965 (4.5).5 (8.).5 (8.).65 (.).65 (.).5 (0.86).5 (0.86).800 (45.7).800 (45.7).5 (6.4).5 (6.4).5 (6.4).5 (6.4).5 (6.4).5 (6.4).8 (5.79).96 (7.5).7 (6.88).94 (0.0) ***Weight given is /", uninsulated, solid, #5 W gold plated copper pigtails. verage Weights** oz. (gm.) ±5%.06 (.79).06 (.79).084 (.9).08 (.7).05 (.99).04 (.97).9 (.9).8 (.6).40 (.99).9 (.96).6 (4.59).60 (4.56).9 (5.50).88 (5.5).500 (4.).040 (9.5) Panel Mounting imensions (Sizes 9 00).00 ±.005 (5.08 ±0.).00 ±.005 (7.6 ±0.).95 ±.005 (0.0 ±0.) Plug and Receptacle Rear Mounted Plug and Receptacle ront Mounted Plug ront Mounted Receptacle Rear Mounted 0
Micro Metal Shell.050" ontact Spacing Panel utouts NOT: See page for rear panel mounting configuration. Shell Sizes 9 thru 5 TYP. TYP..00.000 (.54) +0.) R TYP. 0.00.450±.00 (.4±0.05).00 (0.76) TYP. + + + + ULL R. (TYP.).05 (0.8)R. (TYP) ULL R. (TYP.) 6 /7 TYP igure ront Mounting igure Rear Mounting ULL R. (TYP.) igure dgeboard Mounting PNL R. Shell Size 00.8 (.00.000 +0. 0.00 ).05 (0.8) R. MX (TYP.).805.000.8.000.805.000 (45.85 +0. ) (.00 +0.) +0. (45.85 ) 0.00 0.00 0.00.6.000 (9.7 +0.0) 0.00.456.000 (6.98 +0.0 ) 0.00 ULL R. (TYP.) igure ront Mounting.5 (.8 ).50.000 (8.6 +0.0) 0.00 ULL R. (TYP.) igure Rear Mounting.450+_.00 (.4+_0.05).40.000 (0.8 +0.0) 0.00.00 (0.76) TYP. ULL R. (TYP.).805.000 (45.85 +0.) 0.00 + + + + PNL R. igure dgeboard Mounting.8.000 (.00 +0. ) 0.00 or 95 Shell Sizes NOTS:. ront panel mounting is the preferred mounting method. ront panel mounting dimensions (figure ) will accommodate either #56 screws or jackpost hardware.. Rear panel mount dimensions (figure ) will accommodate #56 screw hardware only. When mounting the connector with rear panel mount jackpost see the panel cutout dimensions.. dgeboard mounting bracket (figure ) uses # 56 screws. imension.450+/.00 (.4+/ 0.05) locates the receptacle flush with the end of the board. or 00 Shell Size NOTS:. ront mounting is the preferred mounting method. ront panel mounting dimensions (figure ) will accommodate either #440 screws or jackpost hardware.. Rear panel mount dimensions (figure ) will accommodate #440 screw hardware only see the panel cutout dimensions..dgeboard mounting bracket (figure ) uses #4 40 screws. imension.450+/.00 (.4+/ 0.05) locates the receptacle flush with the end of the board. Shell Size 9 5 5 7 5 utout igure.000.408.40.558.55.708.70.808.80.958.95.08.0.058.05.000.7.5.7.5.7.5.7.5.7.5.7.5.5.95.000.570.570.570.70.70.70.870.870.870.970.970.970.0.0.0.70.70.70.0.0.0.000
Micro Metal Shell.050" ontact Spacing Mounting Hardware Views (for sizes 95) This hardware supplied unassembled. LOK SRW RTININ LIP.408 (0.6).8 (4.6).688 (7.48) ONNTOR SHOWN OR R. ONLY MTIN #56 UN PNL R..500 (.7) Screw Lock ssembly USHIN. (5.89).09 (.6) ROMMN PNL THIKNSS #56 UN Jackpost (P) Screw Lock ssembly* *NOT Torque value is.5 in/lbs max..05 (.) TYP. 90 ngle Mounting racket.096 ±.005 (.44 ± 0.)I..70 (4.).78 ±.005 (4.5 ± 0.) #56 UN TH.60 (6.60) 90 ngle Mounting racket +/.005 (±0.) escription Screw Lock ssembly Jackpost kit Part Number 9500000 09505000 N/ N/ Mounting racket 90 for 9 thru 7 Shell Sizes Mounting racket 90 for 5 Shell Size 0595600 0595600.47 (.7).69 (4.9) NOTS: Screw lock assembly (9500000) can be used for front mounting only. Jackpost kit (09505000) consists of two assmblies, shipped unassmbled..50 (8.89) Jackpost ushing (for rear panel mountingfor sizes 95).70 (4.) HX IS.5 (.4)/.5 (.9) ROSS LTS #56 UN TH MTIN.6 (.0).5 (.8) I. TYP.05 (.67).00 (.54) R TYP. 7 6 TYP.500 (.7).480 (.9) #56 UN TH Panel Thickness / (.4).087 (.) /6 (.6).056 (.4) /64 (.).04 (.07) / (0.8).05 (0.64) * kit consists of jackpost, nuts, washers. Jackpost diameter within the "" dimension is.4/.0 (.5/.05). (0.).000 (0.00) Jackpost Kit Number* 09505007 09505006 09505005 09505004 Plug and Receptacle imensions Shell Size 9 5 5 7 5 (0.0).000 (0.00).40 (0.9).55 (4.00).70 (7.8).80 (0.4).95 (4.6).0 (7.97).05 (6.70) (0.0).000 (0.00).5 (6.40).5 (6.40).5 (6.40).5 (6.40).5 (6.40).5 (6.40).95 (7.49) +_.005 (0.).565 (4.5).75 (8.6).865 (.97).965 (4.5).5 (8.4).65 (.).5 (0.86)
Micro Metal Shell.050" ontact Spacing Mounting Hardware Views (sizes 95) This hardware is factory installed..04 ±.004 (0.6 ± 0.0) LLOWL IMTRL LOT.00 (0.5) LLOWL XIL LOT.50 ±.00 (.8 ±.076) MTIN ONNTOR SHOWN OR R. ONLY.490 (.45) MX.75 (8.67) ONNTOR SHOWN OR R ONLY HX H.050 (.7) ROSS LTS.050 (.7) P (R).55 (.94) MX.09 (.6) R..090 ±.005 (.9 ± 0.08)I loat Mount ().0 ±.00 (0.79 ± 0.08) MTIN #56 UN PRT HS.040 (.0) MX XIL LOT Jackscrew (K) Standard Profile MTIN PRT HS.040 (.0) XIL LOT #56 UN Jackscrew (L) Low Profile Shown here is a cutaway view of the float mount for the connector. The basic shell dimensions are the same for the float mount and the screw mounting hole configurations. View shown is for standard float mount front panel mounting. Reverse mounting is available on request. * NOT: Torque values are as follows: Low Profile Jackscrew (L).5 inlbs Standard Jackscrew (K).5 inlbs Mounting Hardware to Military Specification (for sizes 9 00) per MILTL85/5 This hardware supplied in kits unassembled ( pieces of each item). #56 UN THR TYP. PLU (R. WITH.09 (.4) I. MOUNTIN HOLS.06 (.57) HX. (R.) #56 UN THR TYP. PLU (R.) WITH.09 (.4) I. MOUNTIN HOLS.6 (9.7).90 (9.9) SIZ 00 ONLY.00 (0.5) TH'K (R.).00 (0.5) TH'K (R.) igure. Jackscrew Low profile Slotted Head Size 95 Size 00* POTTIN WLL (R.) llen head Optional Head onfiguration Plug and Receptacle Low and High Profile Size 95 Size 00* (same dimensions).868 (.05).90 (.9) POTTIN WLL (R.) igure. Jackscrew High Profile Slotted Head Size 95 Size 00*.5 (.8) HX..87 (4.75) HX. #56 UN THR #440 UN THR LOKWSHR RTININ NUT.54 (.9) HX..87 (4.75) HX..06 ±.00 (.57 ± 0.5) SIZ 00 SM igure. Jackpost ssembly Size 95 Size 00*.90/.85(4.8/4.70).85/.75(4.70/4.44).475 ±.05 (.06 ± 0.64) SIZ 00 SM escription To order hardware kits separately, order either by M85/5** or by 0950XXXX. Size 95 Mod ode Part Number Slotted Head Jackscrew ssy Low Profile (igure ) M5 0950805 Slotted Head Jackscrew ssy Low Profile (igure ) M6 0950807 llen Head Jackscrew ssy Low Profile (igure ) M 0950806 llen Head Jackscrew ssy High Profile (igure ) M 0950808 Jackpost ssy (igure ) M7 095050 Size 00* * * Mod ode Part Number * * 05 06 0 0 07 M5 095080 M6 095080 M 095080 M 0950804 M7 0950500 5 6 7 *Size 00 requires size mounting holes for MilSpec hardware Note: Torque values as follows: Size 95 4.0 inlbs Size 00 6.0 inlbs
Micro Metal Shell.050" ontact Spacing Mounting Hardware Views (for size 00) This hardware supplied unassembled.. ±.005 (. ± 0.) I. #440 UN TH #440 UN TH #4 LOK WSHR PNL MY US WITH.09 (.6) MX THIK PNL +.00 80.005 (4.57 +.05) 0..500 (.70).95 (0.0) MTIN SI #440 UN NOTHIN OR ML TH 90 ngle Mounting racket Jackpost (P).5 ±.005 (5.97 ± 0.).064 ±.00 (.6 ± 0.5) TYP. Note: Size 00 requires.0 dia () mounting hole when using ommercial (P) jackpost kits. 90 ngle Mounting racket escription Jackpost kit Mounting racket 90 Part Number ±.005 (0.) 0950505 N/ 05958000.9 (4.85).70 (9.40) This hardware is factory installed..04 ±.004 (0.6 ± 0.0) LLOWL IMTRL LOT.00 (0.5) LLOWL XIL LOT.74 ±.005 (4.4 ±.0) MTIN ONNTOR SHOWN OR R. ONLY.75 (8.67) HX. SOKT H..078 (.98) ROSS LTS.050 (.7) MIN. PTH MX.09 (.6) R..6 ±.00 (.9 ±.05) I loat Mount () Std..0 ±.00 (0.79 ± 0.08) MTIN #440 UN TH PRT HS.040 (.0) MX XIL LOT Jackscrew (K) Standard MTIN SI.55 (.94).040 (.0) XIL LOT #440 UN TH Jackscrew (L) (Low Profile) *NOT: Torque values are as follows: Low Profile Jackscrew (L)4.0 inlbs Standard Profile Jackscrew (K)4.0 inlbs Jackpost ushing (for Rear Panel Mounting) NIN /6" HX. LOKIN POST #440 UN imensions for Rear Panel Mounting.800 ±.005 (45.7 ± 0.) Panel Thickness / (.4) /6 (.6) / (0.8) /64 (.) (0.).000 (0.00).087 (.).058 (.4).05 (0.64).04 (.07) Jackpost Kit Number* 095050 095050 0950500 095050 RPTL SHOWN OR R. ONLY #440 THR RTININ NUT.70 (4.).500 (.70).5 (.8.000 +0. 0.00 R ).56.000 (8.5+.0 ) 0.00.40 (0.8.000 +.0 ) 0.00.6 (4.09).59 (4.04) I. * jackposts, nuts, washers Torque value for size 00 Note: Size 00 requires mounting hole shell size when using rear panel mount jackposts 4
Micro Metal Shell.050" ontact Spacing onnector Saver Save wear and tear on your equipment and systems connectors by using the "onnector Saver". The multimatings and unmatings experienced by most connectors during testing and final check out can be eliminated. Simply mate the "onnectors Saver" to your unit and use the opposite side for your testing interface...less wear, less tear, less chance of damage. It is available in all eight standard layouts. Mating hardware is available and can be ordered either separately or included with the connector saver..040 (.0) LLOWL XIL LOT #56 UN TH (95) (TYP.).790 (0.07).5 (8.00) JKSRW/JKPOST USHIN (OR RRN ONLY S ORRIN INORMTION LOW.) MIROPIN MIROSOKT ONNTOR RPT ONNTOR, PLU KPOTTIN, POXY INTRIL SL.090 (.9) R. (TYP.).900 (.86) R. (TYP.) Size 9 Shown RIN (TYP.) Size 9 5 5 7 5 00 lectroless Nickel (74) Plated admium over Nickel (0) Plated With Hardware W/O Hardware With Hardware W/O Hardware *Hardware Kits 9847986 9847987 9847988 9847989 9847990 984799 984799 984799 984798 984799 984790 98479 984794 984795 984796 984797 9847978 9847979 9847980 984798 984798 984798 9847984 9847985 97947 97947 97947 979474 979475 979476 979477 979477 0950504** 0950504** 0950504** 0950504** 0950504** 0950504** 0950504** 0950804*** ±.005 (0.).785 (9.94).95 (.75).085 (7.56).85 (0.0).5 (.9).485 (7.7).45 (6.45).70 (55.).565 (4.5).75 (8.6).865 (.97).965 (4.5).5 (8.).65 (.).5 (0.86).800 (45.7).5 (8.9).94 (0.0) * Kit contains jackpost/jackscrew bushings and Rings. ** Size 95#56 UN Thread *** Size 00#440 UN Thread 5
Micro Metal Shell.050" ontact Spacing MILTL85 How to Order MILTL85 Part Number Nomenclature Slash Sheets 9 M85/ 0 H00 * * * * * * SRIS M MV Metal Shell, Liquid rystal Polymer (LP) iallyl Phthalate Insulator Polyester Insulator MIL85 SLSH SHT 0 0 0 04 05 06 07 08 09 Plug, onnector, Solderpot Receptacle, onnector, Solderpot Plug, onnector, rimp Type Receptacle, onnector, rimp Type Hardware Only 7 Plug, onnector, Solderpot Receptacle, onnector, Solderpot Plug, onnector, rimp Type Receptacle, onnector, rimp Type Metal Shell Plastic 5 INSRT RRNMNT H MTL SHLL 9 ontact 5 ontact ontact 5 ontact ontact 7 ontact 5 ontact 00 ontact PLSTI 9 ontact 5 ontact ontact 5 ontact ontact 7 ontact 5 ontact 5 NOTS: or every Mil Spec Part Number, ITT has one corresponding part number shown an example Tolerance on wire lengths: 8", 6" and 7" long +.00"/0.00".5" and.00" +.00"/.000" 4 or space application, connector shell finish must be "74" and wire must be per MILW759/6. ny deviations to these P/N's will result in assignment of a special P/N, consult factory. WIR TYP No Number or Solderpot 0 0 0 8" 6" 8" 5 Size 00 not available in / 06 through / 09. (Plastic shell) 6 olor coding in accordance with MILST68, System, no parenthesis. See page 8 for color code chart. SHLL INISH 7 or mounting hardware to Military Specification (sizes 9 to 00) see page. N 74 lectroless Nickel 74 04 05 06 07 08 09 0 4 5 6 6".5".0".5".0" 8" 6" 8" 6" 7" 7" 7" 7" long, #6 W per MILW759/69 (all white) long, #6 W per MILW759/69 (all white) long, #6 W per MILW759/6 olor oded per MILST68, System, 0 colors repeating long, #6 W per MILW759/6 olor oded per MILST68, System, 0 colors repeating long. #5 W, type S per QQW4, old Plated long, #5 W, type S per QQW4, old Plated long, #5 W, type S per QQWW4, Tin Plated long, #5 W, type S per QQW4, Tin Plated long, #6 W per MILW759/69 (all white) long, #6 W per MILW759/69 (all white) long, #6 W per MILW759/6 olor oded per MILST68, System, 0 colors repeating long, #6 W per MILW759/6 olor oded per MILST68, System, 0 colors repeating long, #6 W per MILW759/69 (all white) long, #6 W per MILW759/6 olor oded per MILST68, System, 0 colors repeating long, #6 W per MILW759/69 (all white) long, #6 W per MILW759/6 olor oded per MILST68, System, 0 colors repeating No number for plastic type connector for admium/yellow chromate over nickel 6 6 6 6 6 6 6
Micro Metal Shell.050" ontact Spacing MILTL85 How to Order MILTL85 Part Number Nomenclature Slash Sheets 07 M85/ 0 * * * SRIS onnector, lectrical, Rectangular Microminiature, Polarized Shell P oard Mounting MIL85 SLSH SHT 0 onnector, Plug, ondensed oard Right ngle (R), Sizes 9 7 onnector, Plug, R, Size 5 onnector, Plug, R, Size 00 onnector, Receptacle, R, Sizes 9 7 4 onnector, Receptacle, R Size 5 5 onnector, Receptacle, R, Size 00 6 onnector, Plug, oard Right ngle (R), Sizes 9 7 7 onnector, Plug, R, Size 5 8 onnector, Plug, R, Size 00 9 onnector, Receptacle, R, Sizes 9 7 0 onnector, Receptacle, R Size 5 onnector, Receptacle, R Size 00 onnector, Plug, oard Straight (S), Sizes 9 7 onnector, Plug, S, Size 5 4 onnector, Plug, S, Size 00 5 onnector, Receptacle, S, Sizes 9 7 6 onnector, Receptacle, S, Size 5 7 onnector, Receptacle, S Size 00 INSRT RRNMNT H MTL SHLL 9 ontact 5 ontact ontact 5 ontact ontact 7 ontact 5 ontact 00 ontact WIR TYP No Number or Solderpot NOTS: 0.09" long, #4 W solid copper wire per QQW4, Type S, solder dipped or every Mil Spec Part Number, ITT has one 0.40" long, #4 W solid copper wire per QQW4, Type S, solder dipped corresponding part number 0.7" long, #4 W solid copper wire per QQW4, Type S, solder dipped Tolerance on wire lengths ±.05 or space application, connector shell finish must be "N". SHLL INISH 4 ny deviations to these P/N's will result in assignment No letter for plastic type connector of a special P/N, consult customer service. admium / Yellow chromate over nickel N lectroless Nickel HRWR N No jackpost P Jackpost (permanently attached) T Threaded insert 7