Gauges and Thermometers

Technical Guide Gauges and Thermometers Pressure Gauges Thermometers Altitude Gauges Sprinkler Gauges Industrial Gauges Logo Gauges Ancillary Equipment

Pressure Gauges Pressure gauges in this catalogue are activated by a responsive metal element which deforms under the effect of the pressure being measured. The following British and European Standards form the basis of the design and manufacture of the Jet range Series of pressure gauges and of these guidelines. They should also be the source of reference for additional information: BS EN 837-1 : 1998 Bourdon Tube Pressure Gauges Dimensions, Metrology, requirement and testing Jet range has a wide selection of gauges and thermometers, which are used to monitor critical elements that must be controlled in order to achieve desired performance. This guide will allow you to select the most appropriate product to meet a variety of requirements. The Jet range encompasses: Pressure Gauges - 50mm, 100mm, and 150mm diameters in a variety of pressure settings BS EN 837-2 : 1998 Selection and Installation recommendations for pressure gauges. BS EN 837-3 : 1998 Diaphragm and Capsule Pressure Gauges - Dimensions, Metrology, requirement and testing Thermometers - 100mm and 150mm diameter bi-metal thermometers - Clip on pipe thermometer - Electronic digital thermometer 2 Thermometers The thermometers in this catalogue have circular dials and are actuated by a bimetal strip element, linked to the pointer. The following British and European Standard forms the basis of the design and manufacture of the Jet range series of thermometers and of their guidelines. The standard should also be the source of reference for additional information: Altitude and Sprinkler Gauges - 80mm combined altitude gauge and thermometer - Altitude gauges up to 40 metres - Sprinkler gauges are glycerine filled with two pressure options to choose from BS EN 13190 : 2001 Dial Thermometers Contents page Pressure Gauges 4 Thermometers 5 Clip on Pipe Thermometer 5 Electronic Digital Thermometer 5 Altitude Gauges 6 Industrial Gauges 7 Logo Gauges 8 Logo Gauges Order Form 9 Ancillary Equipment 11 Industrial Gauges - Bourdon Tube Pressure Gauges for Standard Industrial Applications (Accuracy Class 1.0) - Bourdon Tube Pressure Gauges for Standard Industrial Applications (Accuracy Class 1.6) - Stainless Steel Bourdon Tube Pressure Gauges for Chemical Applications (Accuracy Class 1.6) Logo Gauges - Pressure gauges - Altitude gauges - Bi-metallic dial thermometers Introduction

Introduction Pressure Gauges Safety The range of the pressure gauge should be selected such that the maximum working pressure does not exceed 75% of the fullscale value when measuring constant pressure, or, 65% for fluctuating pressure. The criteria for the selection of a gauge are a function of four factors. 1. The pressure range (up to 25 bar, or, over 25 bar) 2. The dial size (less than 100mm, or, 100mm and above) 3. Whether the gauge is Dry or liquid (eg glycerine) filled 4. The state of the material under pressure (as a liquid, or, as gas or steam) Storage Pressure gauges should be kept in dry, clean conditions within a temperature range of -40 to +60 C and should be protected from impact damage. Installation It is advisable to install the gauge with an isolating cock or valve that facilitates removal of the gauge for maintenance or replacement. On installation a leak tight seal should be achieved. If using sealing materials ensure these do not prevent the fluids entering the gauge. Gauges should be mounted vertically unless designed (and marked) otherwise. Gauges fitted with a blow out device must have at least 20mm clearance from any obstacle to permit the blow out device to operate correctly. Installation should take account of the ambient temperature conditions and should these affect the gauge adversely (eg cause the medium to freeze within the pressure element, then the gauge should be located remotely. A pressure gauge should not be installed in contact with fluids whose temperature is outside -30 to +60 C. Under these conditions a syphon should be installed or a suitably remote location selected, where the temperature conditions are more suitable. 3 Thermometers Safety The 'Jet range' series of pipeline thermometers are supplied, as standard, with solid brass pockets with a process connection of 1 2" BSP. The pockets are produced as an interference fit on the brass stem to ensure a high degree of sensitivity. The thermometers should not be installed without these, or other pockets. Storage Thermometers should be kept in dry, clean conditions within a temperature range of -20 to +60 C and should be protected from impact damage. Installation Thermometers will only measure the temperature experienced by the sensor probe. It is important, to achieve correct readings, that the probe is fully immersed into the flow of the pipeline or vessel. Correct nominal range and stem lengths must be selected before a thermometer is installed.

Pressure Gauges 50mm Diameter Bourdon tube copper alloy Black steel case Acrylic window 1 4" BSP bottom or back entry male connection Direct mounting Dual scale bar and psi Accuracy class 2.5 to BS EN 837-1:1998 4 Materials 100mm Pressure Gauge Those parts of a pressure gauge which are in contact with the fluid being measured (the wetted parts ) are, as standard, made from alloys of copper (brass and phosphor bronze) but can be stainless steel or other more exotic materials. If doubt exists as to the suitability of the standard gauge, please contact a member of our sales staff. 100mm and 150mm Diameter Bourdon tube copper alloy Black steel case Acrylic window Chrome plated bezel 3 entry male connection Direct mounting Dual scale bar and psi Accuracy class 1.6 to BS EN 837-1:1998 for 50mm Diameter for 100/150mm Diameter Cat. No. 100mm 150mm N20510 Pressure gauge 0-6 bar & psi bottom entry N20590 Pressure gauge 0-2.5 bar & psi N20511 Pressure gauge 0-6 bar & psi back entry N20591 N20605 Pressure gauge 0-4 bar & psi N20512 Pressure gauge 0-16 bar & psi bottom entry N20592 N20606 Pressure gauge 0-6 bar & psi N20513 Pressure gauge 0-16 bar & psi back entry N20593 N20603 Pressure gauge 0-10 bar & psi N20594 Pressure gauge 0-16 bar & psi N20595 Pressure gauge 0-25 bar & psi 50mm Pressure Gauge N20955 Back flange for 100mm dia pressure gauge Pressure Gauges

Thermometers Thermometers 100mm and 150mm Diameter Black steel case Acrylic window Chrome plated bezel Bottom and back entry 50mm or 100mm immersion length c/w BSP 1 2" pocket Pocket for 100mm dial - push fit Pocket for 150mm dial - screw fit 100mm and 150mm Diameter Dual scale ºC and ºF Accuracy class 1 to BS EN 13190:2001 Materials The standard pockets supplied with these thermometers are machined from solid brass and are suitable for pressures up to 25 bar. Alternative materials such as stainless steel can be supplied. Customers uncertain of the suitability of the standard pockets should contact a member of staff. 5 100mm 150mm 100mm 150mm N20700 N20610 Thermometer 0-120ºC c/w 50mm pocket bottom entry N20706 N20622 Thermometer -20-60ºC c/w 50mm pocket back entry N20701 N20611 Thermometer 0-120ºC c/w 100mm pocket bottom entry N20707 N20623 Thermometer -20-60ºC c/w 100mm pocket back entry N20702 N20612 Thermometer 0-120ºC c/w 50mm pocket back entry N20956 50mm Spare brass screwed pocket, 150mm dial N20703 N20613 Thermometer 0-120ºC c/w 100mm pocket back entry N20710 50mm Spare brass push fit pocket, 100mm dial N20704 N20620 Thermometer -20-60ºC c/w 50mm pocket bottom entry N20957 100mm Spare brass screwed pocket, 150mm dial N20705 N20621 Thermometer -20-60ºC c/w 100mm pocket bottom entry N20712 100mm Spare brass push fit pocket, 100mm dial Note: Push fit gauges can be installed into an existing screw fit pocket Clip on Pipe Thermoometer 66mm case size Comes complete with fixing spring Electronic Digital Thermometer Data hold function Large digital display Magnetic attachment Resolution 0.1 C (between -19.9 C and +199 C, otherwise 1 C) 1500mm cable with stainless steel probe Clip on Pipe N21295 Temperature range 0 to +120ºC N21299 Temperature range -50ºC to +120ºC Electronic Digital Thermometer N21296-40 to +40ºC N21296-40 to +200ºC

Altitude Gauges 100mm diameter Bourdon type copper alloy Black steel case Acrylic window Chrome plated bezel Loose red pointer 3 connection Direct mounting Dual scale metres and feet Accuracy class 1.6 to BS EN 837-1:1998 Altitude Gauge N20525 N20526 N20527 N20528 Altitude Gauge 0-10 mtr & 30Ft Altitude Gauge 0-15 mtr & 50Ft Altitude Gauge 0-25 mtr & 80Ft Altitude Gauge 0-40 mtr & 130Ft 6 80mm Combined Thermometer & Altitude Gauge N20730 Black steel case Acrylic window Chrome plated bezel 1 2" BSP bottom connection Direct mounting Scale 0/120ºC & 0/30 metre Sprinkler Gauges 100mm diameter Weatherproof stainless steel case Phosphor bronze/brass wetted parts Direct vertical brass mounting 3 8" female x 1 2" male BSPT self seal leakproof connector Accuracy class 1.0 Glass window Stainless steel bayonet type bezel Glycerine filled Component N21246 N21247 80mm Combined Thermometer & Altitude Gauge Sprinkler pressure gauge 0-10 bar Sprinkler pressure gauge 0-16 bar Sprinkler Gauge Altitude Gaues & Sprinkler Gauges

Industrial Gauges Industrial Gauges Bourdon Tube Pressure Gauges for Standard Industrial Applications (Accuracy Class 1.0) Conforms to BS EN 837-1 Dry or glycerine filled 100mm diameter Weatherproof stainless steel case Phosphor bronze/brass wetted parts Direct vertical brass mounting 3 8 " BSP male connection Glass window Stainless steel bayonet type bezel Glycerine N21005 N21035 Pressure Gauge 0-30 PSI/bar N21006 N21036 Pressure Gauge 0-60 PSI/bar N21007 N21037 Pressure Gauge 0-100 PSI/bar N21008 N21038 Pressure Gauge 0-160 PSI/bar N21009 N21039 Pressure Gauge 0-200 PSI/bar N21010 N21040 Pressure Gauge 0-300 PSI/bar N21011 N21041 Pressure Gauge 0-400 PSI/bar N21012 N21042 Pressure Gauge 0-600 PSI/bar Bourdon Tube Pressure Gauge Bourdon Tube Pressure Gauges for Standard Industrial Applications (Accuracy Class 1.6) Conforms to BS EN 837-1 63mm diameter Weatherproof stainless steel case Phosphor bronze/brass wetted parts Direct vertical brass mounting 1 4 " BSP male connection Direct vertical or horizontal brass mouting Plastic window Glycerine N21185 N21215 Pressure Gauge 0-60 PSI/bar N21186 N21216 Pressure Gauge 0-100 PSI/bar N21187 N21217 Pressure Gauge 0-160 PSI/bar N21188 N21218 Pressure Gauge 0-200 PSI/bar N21189 N21219 Pressure Gauge 0-300 PSI/bar N21190 N21220 Pressure Gauge 0-400 PSI/bar N21191 N21221 Pressure Gauge 0-500 PSI/bar N21192 N21222 Pressure Gauge 0-600 PSI/bar N21193 N21223 Pressure Gauge 0-1000 PSI/bar Bourdon Tube Pressure Gauge (Glycerine Filled) 7 Stainless Steel Bourdon Tube Pressure Gauges for Chemical Applications (Accuracy Class 1.6) For all process apllications (except direct hygienic) where the medium is damaging to brass/ bronze alloys Bourdon Tube Pressure Gauge (Stainless Steel) Conforms to BS EN 837-1 100mm diameter Weatherproof stainless steel case Stainless steel wetted parts 3 8 " or 1 2 " BSP male connection Direct vertical or stainless steel mouting Stainless steel bayonet type bezel Laminated safety glass window 3 4 " BSP N21255 N21256 N21257 N21258 N21259 N21260 N21261 N21262 N21263 Pressure Gauge 0-15 PSI/bar Pressure Gauge 0-30 PSI/bar Pressure Gauge 0-60 PSI/bar Pressure Gauge 0-100 PSI/bar Pressure Gauge 0-160 PSI/bar Pressure Gauge 0-200 PSI/bar Pressure Gauge 0-300 PSI/bar Pressure Gauge 0-400 PSI/bar Pressure Gauge 0-600 PSI/bar 1 2" BSP N21285 N21286 N21287 N21288 N21289 N21290 N21291 N21292 Pressure Gauge 0-1.6 bar Pressure Gauge 0-2.5 bar Pressure Gauge 0-4 bar Pressure Gauge 0-6 bar Pressure Gauge 0-10 bar Pressure Gauge 0-16 bar Pressure Gauge 0-25 bar Pressure Gauge 0-40 bar

Jet Logo Gauges Jet range logo gauges give you the customer the opportunity to use your company logo or emblem on your own tailor-made gauge. This service is available on a select range of pressure gauges, thermometers and altitude gauges, adhering to the same standards and quality of the standard Jet range gauges which are all covered by a 12 month guarantee. All Jet range Logo gauges feature black steel cases, acrylic windows and chrome plated bezels. Logo Gauge 100mm diameter - Vertical N20740 N20741 0-2 bar 0-4 bar 150mm diameter - Vertical N20750 N20751 0-4 bar 0-6 bar Pressure Gauges 100mm and 150mm diameter Bourdon Tube copper alloy N20742 N20743 N20744 0-6 bar 0-10 bar 0-16 bar N20752 0-10 bar 3 8 " BSP bottom entry male connection Direct mounting N20745 0-25 bar Dual scale (bar and PSI) 8 Accuracy class to BS EN 837:1998 Altitude Gauges Logo Gauge Cat. No. N20760 N20761 N20762 N20763 0-10 metre 0-15 metre 0-25 metre 0-40 metre Bourdon Tube copper alloy 3 8 " BSP bottom entry male connection Direct mounting Dual scale (metric and imperial) Accuracy class to BS EN 837:1998 Bi-Metallic Dial Thermometers Quality bi-metallic movement Bottom or back entry options available 50mm or 100mm immersion lengths Comes with brass pocket 1 2 " BSP x 12mm Dual Scale (ºC and ºF) Accuracy class to BS EN 13190: 2001 100mm diameter - Vertical N20768 N20770 N20772 N20774-20+60ºC and L = 50mm -20+60ºC and L = 100mm 0+120ºC and L = 50mm 0+120ºC and L = 100mm 100mm diameter - Horizontal N20776 N20778 N20780 N20782-20+60ºC and L = 50mm -20+60ºC and L = 100mm 0+120ºC and L = 50mm 0+120ºC and L = 100mm 150mm diameter - Vertical N20784-20+60ºC and L = 50mm N20786-20+60ºC and L = 100mm N20788 0+120ºC and L = 50mm N20790 0+120ºC and L = 100mm 150mm diameter - Horizontal N20792-20+60ºC and L = 50mm N20794-20+60ºC and L = 100mm N20796 0+120ºC and L = 50mm N20798 0+120ºC and L = 100mm L = Pocket length Logo Gauges

XXXXX XXXXXXXXXXXXXXXXXXXXXXXXXXXX Logo Gauges Logo Gauges 9 LOGO NAME: TOTAL NO.OF GAUGES: Please send high resolution image of new logo (300dpi) to: jet.gauges@wolseley.co.uk MIN ORDER QTY - 25 UNITS TOTAL IF LESS THAN 25 ARE REQUIRED THERE WILL BE A 25 SET UP CHARGE CUSTOMER NAME: CUSTOMER CONTACT: TEL. NUMBER: WOLSELEY CONTACT NAME: SIGNATURE: BRANCH ADDRESS: TEL. NUMBER: EMAIL: FAX:

Order Quantity Pressure Gauges 100mm diameter Cat. No. Pressure range psi Quantity N20740 0-2.5 0-30 3 N20741 0-4 0-60 3 N20742 0-6 0-90 3 N20743 0-10 0-150 3 N20744 0-16 0-230 3 N20745 0-2.5 0-360 3 150mm diameter Cat. No. Pressure range psi Quantity N20750 0-4 0-60 3 N20751 0-6 0-90 3 N20752 0-10 0-150 3 Altitude Gauges 100mm diameter 10 Cat. No. Altitude range (M) (Ft) Quantity N20760 0-10 0-30 3 N20761 0-15 0-60 3 N20762 0-25 0-80 3 N20763 0-40 0-130 3 Bi-metal Thermometers 100mm diameter Cat. No. Temperature range Immersion length (mm) Connection type N20768-20ºC to +60ºC 50 bottom connection N20770-20ºC to +60ºC 100 bottom connection N20772 0 to +120ºC 50 bottom connection N20774 0 to +120ºC 100 bottom connection N20776-20ºC to +60ºC 50 back connection N20778-20ºC to +60ºC 100 back connection N20780 0 to +120ºC 50 back connection N20782 0 to +120ºC 100 back connection Quantity 150mm diameter Cat. No. Temperature range Immersion length (mm) Connection type N20784-20ºC to +60ºC 50 bottom connection N20786-20ºC to +60ºC 100 bottom connection N20788 0 to +120ºC 50 bottom connection N20790 0 to +120ºC 100 bottom connection N20792-20ºC to +60ºC 50 back connection N20794-20ºC to +60ºC 100 back connection N20796 0 to +120ºC 50 back connection N20798 0 to +120ºC 100 back connection Quantity Logo Gauges

XXXXX XXXXXXXXXXXXXXXXXXXXXXXXXXXX Ancillary Equipment Ancillary Equipment Jet range offers a variety of ancillary equipment to support the gauges and thermometers in the range. 1 4 " 3 8 " 1 2 " N60521 N60522 N60523 Brass F x F Gauge Cock N69001 K69002 N69003 Jet Lever Operated Ball Valve N20901 N20902 N20903 U-Syphon: Mild steel - N20905 - U-Syphon: Brass N20908 N20909 N20910 Ring-Syphon: Mild Steel N20911 N20912 N20913 Ring Syphon: Brass - N20915 - Ring-Syphon: Stainless Steel N20920 N20921 N20922 Brass M/F Snubber (used to eliminate surge and pressure pulsation to pressure gauges) Options for Industrial Gauges 11 Industrial Applications (Accuracy Class 1.0) Options 1 2" BSP vertical male connection 160mm diameter gauges Back flange for surface mounting Ranges: compound, vacuum and up to 15,000 PSI/bar Industrial Applications (Accuracy Class 1.6) Options Suitable for Panel Mounting Ranges: Compound, Vacuum and up to 10,000 PSI/Bar Chemical Applications (Accuracy Class 1.6) Options Back flanges for surface mounting Ranges: compound, vacuum and up to 10,000 PSI/Bar LARGE SELECTION AVAILABLE Including Logo Gauges and Industrial Gauges www.jetrange.co.uk

Pipe Center is the specialist supplier of commercial heating plant and pipe systems. Branches offer a range of products including boilers, water heaters, radiators, pump and commercial showers. Pipe Center also stock the widest ranges of pipes, fittings and valves in: Carbon steel Copper Brass Pressure plastics Stainless steel Bronze Branch locations for a list of the branch locations please visit: www.pipecenter.co.uk For further information about Jet range products, please visit www.jetrange.co.uk or contact 0870 8506538 Some products also available from: www.plumbcenter.co.uk www.partscenter.co.uk www.climatecenter.co.uk Whilst every care has been taken to ensure that the information included in this document was accurate at the time of printing, we reserve the right to change specifications at any time. The photographs reproduced in this publication are within the constraints of the printing process and are NOT to be used for matching purposes. E&OE. Catalogue Number: Y98056 ref:4569