SFETY GTE SSEMLY INSTRUTIONS TO SUIT LUMINIUM / FIREGLSS PLTFORM STEP LDDERS WITH 560mm HNDRIL WIDTH 560mm Please read all these instructions completely before mounting and using the Safety Gate. Do not attempt to fit this Safety Gate unless you are competent in the use of hand tools including: Spanners and Power Tools. Do not attempt to fit this Safety Gate unless you understand basic technical drawings and can relate such drawings to step by step instructions. If you do not understand these instructions, contact your employer, dealer, or the manufacturer for assistance. Your original product has been manufactured to exacting standards. If the Safety Gate is fitted incorrectly you can compromise your safety and the integrity of the product. If the Safety Gate is fitted incorrectly Werner o. will not be liable for any damage or personal injury which occurs as a result. y fitting this Safety Gate to your product you may void the warranty on the product. If used and cared for properly, it will provde you with many years of reliable service. Prior to commencement, identify all the kit components required. If any components are missing or damaged, retun the kit to the place of purchase. WRNING: Do not substitute any components. PGE 1
Step 1 - Identify Kit omponents Identify all the components in the carton. Rear ross ar (x1) RHS Side rm (x1) Tools required: - lamp - Drill - 6.5mm Drill bit - 11mm Spanners (x2) LHS Side rm (x1) Gate Rail (x1) Parts Kit (x1) Identify all the components in the Parts Kit. Drilling Template (x1) 2 1/2" olt (x2) 2" olt (x3) 1 1/4" olt (x4) Joiner (x2) Gate Rail lip (x1) olts (ctual Size) Pivot ush (x2) Washer (x12) Nut (x5) PGE 2
Step 2 - Drill Mounting Holes Handrail Front face of stile LHS stile RHS stile ORRET placement of drilling template Drill through handrail and stile using a 6.5mm drill bit. Drill through hinge plate and stile using a 6.5mm drill bit. Hinge Plate Position the drilling template against the front face of the stile and against the outside face of the handrail and hinge plate. Slide up against bottom of handrail. lamp in place. D Use the drilling template to drill the RHS stile. INORRET placement of drilling template PGE 3
Step 3 - Mount LHS Slide Pivot Slide pivot Remove slide pivot from side arm assembly. Insert 2" bolt into slide pivot and through the drilled hole in the handrail. LHS side arm assembly. Slide pivot PGE 4 olt Fit washer and nut onto bolt. Tighten nut and bolt until all surfaces contact. (Do not over tighten).
Step 4 - Mounting LHS Side rm ssembly Slide pivot Reassemble side arm assembly onto slide pivot. LHS side arm assembly. Side arm support Pivot bush Insert pivot bush into side arm support. Drilled hole in hinge bracket and stile Insert 2 1/2" bolt through washer, pivot bush and through the drilled hole in the hinge bracket and stile. Step 4 continued on PGE 6 PGE 5
Step 4 (continued) - Mounting LHS Side rm ssembly D olt ssemble washer and nut onto bolt. (Firmly tighten nut and bolt). E Ensure the side arm assembly will slide and pivot to this position. F Repeat steps 3 & 4 to mount the RHS side arm assembly. PGE 6
Step 5 - ssembly of Rear ross ar Rear cross bar Insert joiner into end of side arm. Side arm Insert rear cross bar into joiner. Side arm Rear cross bar Rear cross bar Insert 1 1/4" bolts through washers and into side arm and rear cross bar. (Firmly tighten bolts). D Repeat step 5 to assemble the other end of the rear cross bar. PGE 7
Step 6 - ssembly of Gate Rail Gate rail Side arm assembly Position gate rail into side arm assembly Insert 2" bolt through washer, side arm hinge bracket and gate rail. Fit washer and nut onto bolt. Tighten nut and bolt until all surfaces contact. Side arm hinge bracket D ssemble gate rail clip onto side arm hinge bracket. Gate rail clip Side arm hinge bracket PGE 8 2015 Werner o. P/N107989-03 Rev 10/15