F-Series Plus ylinders Technical features Medium: Filtered, lubricated or nonlubricated, compressed air Operating pressure 200 psig (3.6 Bar) Max. Temperature range: Standard Nitrile seals: -40 F to 200 F (-40 to 93 ) 50 F max. with Bumper Option High Temp seals: -20 F to 400 F (-29 to 205 ) *With dew point of supply air less than air temperature below 35 F (2 ). Lubrication: All F-Series Plus cylinders are prelubricated at the time of assembly with a PTFE based grease, for non-lube service and long life. Side loading: ylinders are specifically designed to push and pull. Side loading and misalignment of the piston rod should be avoided to ensure maximum operating performance and life. Materials: ylinder Body: 304 Stainless Steel Head and ap: lear Anodised Aluminum Alloy Piston Rod: 303 Stainless Steel Rod Bearing: Oil Impregnated Bronze Piston: Aluminum Alloy Rod & Piston seals: Nitrile Options selector Series Substitute Single Rod end FP Double Rod end FPD Spring Extend FP Spring Retract FPR Bore Substitute 9/6" 056 3/4" 075 -/6" 06 -/2" 50 2" 200 2-/2" 250 3" 300 Stroke Increments of /8" Mounting Options Substitute *Screw learance Holes Front SF *Screw learance Holes Rear SR *Screw learance Holes Both ends SB Basic Model (std. c bored mtg. holes) BAM **Front Trunnion TMF **Rear Trunnion TMR **Trunnion both ends TMB Pivot Mount PTM Threaded mounting holes Front THF Threaded mounting holes Rear TH Threaded mounting holes Both ends THB ***Nose Mount NMT * Screw clearance to allow bolt head to pass through - no counter bores ** Not available on 9/6" bore *** Available in FP, FP, and FPR.Includes a heavy duty end cap and rod wiper. FP 06 x 2.375 - PTM - PS Options Substitute Bumper both ends (not avail. with HT) UB Bumper Head (not avail. with HT) UH Bumper ap (not avail. with HT) U Non-Standard Female Thread** FT( ) Heavy Duty Rear End ap² HD Alternate Port Location PL( ) Low Friction Seals² LF Magnetic Piston² PS M,M2, Switch Rail and Position M3,M4 (switches ordered separately) No Rod Thread PR Non-Standard Male Thread TM( ) Thread Extension over standard TX( ) (specify additional length) 3 Rod Extension over standard RX( ) (specify additional length) 3 Stainless Steel Fasteners (25 PSI Max) SF High Temperature Seals4 **HT Rod Wiper RW Stroke is reduced by.03" per bumper. Bumpers are rated to 50 F 2 Overall length of cylinder may increase with this option. 3 onsult factory for negative thread or rod extensions. 4 Not available in single or reverse acting models. AT-76
F-Series Plus ylinders Quality and durability in a compact, high performance cylinder! The Norgren F-Series Plus offers a compact design using the highest quality components for dependable service and long life. All components of the F-Series Plus cylinder have been specifically selected to provide optimum reliability and performance. 2 3 4 5 6 Head/ap: Aluminum alloy, clear anodised for corrosion resistance. 2 Seals: Nitrile, o-ring seals throughout 3 Piston: Aluminum alloy piston is lightweight, yet strong with excellent wear characteristics. 4 Tube: 304 Stainless steel tube, polished and buffed I.D. 5 Rod Bearing: Oil impregnated, bronze bearing, for long cylinder life and non-lube service. 6 Piston Rod: 303 Stainless steel, chrome plated for smooth finish and long seal life. AT-77
F-Series Plus ylinders Force Factor Data Bore ode Force Factor (Area) Extend Retract 9/6" (056) 0.25 0.20 3/4" (075) 0.44 0.36 -/6" (06) 0.89 0.69 -/2" (50).77.46 2" (200) 3.4 2.70 2-/2" (250) 4.9 4.47 3" (300) 7.07 6.47 Force Output Formula ylinder Output Force = Force Factor (area) x Air Line Pressure (psi) Ex: -/6 bore cylinder operating at 80 psi: Force exerted on the extend: 0.89 x 80 = 7.2 lbs. Force exerted on the retract: 0.69 x 80 = 55.2 lbs. Approximate ylinder Weights (lbs.) FP FPD FPR, FP Nose Mount Option Bore ode Base Adder per /8" stroke Base Adder per /8" stroke Base Adder per /8" stroke Adder to Base Weight 9/6" (056) 0.075 0.005 0.08 0.009 0.094 0.005 0.006 3/4" (075) 0.9 0.006 0.3 0.03 0.38 0.006 0.03 -/6" (06) 0.306 0.09 0.363 0.025 0.33 0.09 0.069 -/2" (50) 0.600 0.025 0.700 0.038 0.669 0.025 0.3 2" (200) 0.83 0.03 0.950 0.044 0.894 0.03 0.69 2-/2" (250).400 0.038.750 0.050.58 0.038 0.94 3" (300).806 0.050 2.375 0.069 2.050 0.050 0.29 Spring Forces Spring Rates Bore ode Maximum 0.2 to ".00 to 2" 2.00 to 3" 3.00 to 4" Force (lbs.) Stroke (lb/in) Stroke (lb/in) Stroke (lb/in) Stroke (lb/in) 9/6" (056) 5.25 4.25.75.24 0.88 3/4" (075) 0.00 6.00 2.50.76.25 -/6" (06).50 6.00 2.50.76.25 -/2" (50) 3.00 5.50 2.25.60.3 2" (200) 3.00 5.50 2.25.60.3 2-/2" (250) 25.00 6.50 2.75.93.38 3" (300) 25.00 6.50 2.75.93.38 Overall length adders for options Length Adder (Add to standard cataloged length) Bore ode LF* HD** PS (Magnetic Piston) (Low Friction Seals) (Heavy Duty ap) FP, FPD FPR FP 9/6" (056) 0.25 0.3 0.88 0.63 0.38 3/4" (075) 0.25 0.3 0.88 0.88 0.88 -/6" (06) 0.38 0.9 0.88 0.88 0.88 -/2" (50) 0.38 0.9 0.88 0.88 0.88 2" (200) 0.38 0.9 0.88 0.88 0.88 2-/2" (250) 0.38 0.25 0.88 0.88 0.88 3" (300) 0.50 0.25 0.88 0.88 0.88 *For Low Friction Seals used in combination with a magnetic piston, use the PS length adder only. **For Heavy Duty End ap used in combination with a magnetic piston, use both HD and PS length adders. AT-78
F-Series Plus ylinders FP (basic model BAM) Double acting, single rod end L port (2 plc) H across flats 2 DD number of clearance holes for D socket head cap screw Port position 3 A Ba + stroke 0.3 E piston rod thd x G deep L 4 FPD (basic model BAM) Double acting, double rod end L port (2 plc) H across flats 2 DD number of clearance holes for D socket head cap screw 0.3 + stroke Bb + stroke 0.3 Port position E piston rod thd x G deep L 4 3 A FP - Double acting, single rod end FPD - Double acting, double rod end Bore ode A Ba* (FP) Bb* (FPD) DD D E Thread G depth F H L 9/6" (056).2 0.56 0.69 0.88 2 #4 8-32 UN.46.25.22.34.4 0-32 UNF 3/4" (075).50 0.56 0.69.22 4 #6 0-32 UN.46.3.25.34.4 0-32 UNF -/6" (06) 2.00 0.88 0.94.69 4 #6 5/6-24 UNF.70.50.44.50.25 /8 NPT -/2" (50) 2.62 0.88.00 2.9 4 #0 3/8-24 UNF.70.63.50.50.25 /8 NPT 2" (200) 3.2 0.95.06 2.69 4 #0 /2-20 UNF.70.75.63.53.25 /8 NPT 2-/2" (250) 3.75.9.3 3.25 4 /4 /2-20 UNF.70.75.63.66.33 /4 NPT 3" (300) 4.25.25.38 3.78 4 /4 5/8-8 UNF.73.88.75.69.33 /4 NPT * Length may increase with certain option combinations. AT-79
F-Series Plus ylinders FPR (basic model BAM) Single acting, spring return L port (2 plc) H across flats 2 DD number of clearance holes for D socket head cap screw Port position 3 A Bc + stroke 0.3 E piston rod thd x G deep L 4 FP (basic model BAM) Single acting, spring extend L port (2 plc) H across flats 2 DD number of clearance holes for D socket head cap screw Port position 3 A Bd + stroke 0.3 + stroke E piston rod thd x G deep L 4 FPR - Single acting, spring return FP - Single acting, spring extend Bc* (FPR) Bd* (FP) 0-".00-2" 2.00-3 3.00-4" 0-".00-2" 2.00-3" 3.00-4" DD D E G F H L Bore ode A Stk. Stk. Stk. Stk. Stk. Stk. Stk. Stk. thread depth 9/6" (056).2 0.8.38.96 2.52.06.62 2.4 2.70 0.88 2 #4 8-32 UN.46.25.22.34.4 0-32 UNF 3/4" (075).50 0.8.38.94 2.50.06.62 2.9 2.75.22 4 #6 0-32 UN.46.3.25.34.4 0-32 UNF -/6" (06) 2.00 0.88.50 2.3 2.75.38 2.00 2.63 3.25.69 4 #6 5/6-24 UNF.70.50.44.50.25 /8 NPT -/2" (50) 2.62 0.88.50 2.3 2.75.38 2.00 2.63 3.25 2.9 4 #0 3/8-24 UNF.70.63.50.50.25 /8 NPT 2" (200) 3.2 0.94.56 2.9 2.8.44 2.06 2.69 N/A 2.69 4 #0 /2-20 UNF.70.75.63.53.25 /8 NPT 2-/2" (250) 3.75.9 2.06 2.94 3.8.94 2.8 2.8 N/A 3.25 4 /4 /2-20 UNF.70.75.63.66.33 /4 NPT 3" (300) 4.25.25 2.2 3.00 3.88 2.00 2.88 2.88 N/A 3.78 4 /4 5/8-8 UNF.73.88.75.69.33 /4 NPT * Length may increase with certain option combinations. AT-80
F-Series Plus ylinders Tunnion mount (TMF, TMR, TMB) P P M M Threaded mounting holes (THF, TH, THB) 3/4" bore and larger N 90 N Threaded mounting holes (THF, TH, THB) 9/6" bore only 4-40 (2) places 90 45 * Screw clearance holes (SF, SR, SB) R thread (4) places * 43 for 3/4 bore only Pivot mount (PTM) T 0.88 X Q dia. for pivot pin Z radius Y U Nose mount (NMT) AA A AF AE 0.3 AB AD W Nose Mount Maximum Torque Recommendation Bore ode Maximum Torque (ft-lb.) 9/6" (056) 2 3/4" (075) 28 -/6" (06) 00 -/2" (50) 20 2" (200) 30 2-/2" (250) 30 3" (300) 30 S Mounting Dimensions (in) Bore ode AA AB A AD AE AF M N P Q R S T U W X Y Z 9/6" (056) 0.06 0.75 Hex 0.38 /2-20 UNF-2A 0.50 0.3 0.88 N/A N/A N/A 0.9 #4-40 UN 0.38 0.9 0.25 0.75 0.7 0.63 0.9 3/4" (075) 0.06 0.75 Hex 0.38 5/8-8 UNF-2A 0.62 0.25.22 0.3 0.2 0.7 0.9 #6-32 UN 0.38 0.9 0.25 0.75 0.23 0.75 0.9 -/6" (06) 0.3.50 Hex 0.75-4 UNS-2A.00 0.55.69 0.50 0.25 0.25 0.9 #6-32 UN 0.38 0.25 0.25 0.8 0.25 0.75 0.9 -/2" (50) 0.3.88 Hex 0.75 -/4-2 UNF-2A.25 0.52 2.9 0.50 0.25 0.25 0.38 #0-24 UN 0.75 0.25 0.44.9 0.34.38 0.38 2" (200) 0.9.88 Hex 0.88-3/8-2 UNF-2A.38 0.52 2.69 0.50 0.25 0.25 0.38 #0-24 UN 0.75 0.3 0.44.25 0.34.38 0.38 2-/2" (250) 0.25.88 Hex.00-3/8-2 UNF-2A.38 0.52 3.25 0.63 0.3 0.33 0.38 /4-20 UN 0.75 0.38 0.44.3 0.4.38 0.38 3" (300) 0.25.88 Hex.00-3/8-2 UNF-2A.38 0.52 3.78 0.63 0.3 0.33 0.63 /4-20 UN.00 0.38 0.56.69 0.4.88 0.38 AT-8
F-Series Plus ylinders Rod Wiper (RW) WD Male Rod End (TM(_)) E LG 0.9 0.38 Bore ode WD 9/6" (056) 0.56 3/4" (075) 0.69 -/6" (06) 0.88 -/2" (50).00 2" (200).3 2-/2" (250).3 3" (300).25 Bore ode E Fine ourse LG 9/6" (056) #8-32 UN N/A 0.38 3/4" (075) #0-32 UNF #0-24 UN 0.38 -/6" (06) 5/6-24 UNF 5/6-8 UN 0.50 -/2" (50) 3/8-24 UNF 3/8-6 UN 0.50 2" (200) /2-20 UNF /2-3 UN 0.63 2-/2" (250) /2-20 UNF /2-3 UN 0.63 3" (300) 5/8-8 UNF 5/8- UN 0.75 levis Bracket TL LD Q pin dia. SQ SD S SH diameter thru MT SQ TH Bore ode Part number LD MT Q S SH SD TH TL 9/6" (056) 3/4" (075) FB- 0.56 0.75 0.9 0.39 #6.00 0.6 0.78 -/6" (06) -/2" (50) 2" (200) FB-2 0.94.38 0.38 0.75 #0.75 0.22.34 2-/2" (250) 3" (300) FB-3.25 2.00 0.63.00 0.25 2.50 0.25.8 AT-82
F-Series Plus ylinders F-Series Plus ylinders Trunnion Block Mount 9/6" to 4" bore NB N dia thru NA LT HT BA BT dia thru M Bore ode Part number BA BT HT LT M N NA NB 3/4" (075) FTB- 0.56 #0 0.63.2 0.3 0.3 0.30 0.22 -/6" (06) -/2" (50) FTB-2 0.8 0.25 0.88.50 0.50 0.25 0.38 0.3 2" (200) 2-/2" (250) FTB-3 0.94 0.3.00.63 0.63 0.3 0.45 0.38 3" (300) Rod levis E thrd Q dia thru NT S S LN MS Bore ode Part number E LN MS NT Q S 9/6" (056) FRE- #8-32 UN 0.38 0.47 0.25 0.9 0.38 3/4" (075) FRE-2 #0-32 UNF 0.38 0.47 0.25 0.9 0.38 -/6" (06) FRE-a3 5/6-24 UNF 0.63 0.47 0.25 0.9 0.38 -/2" (50) FRE-4 3/8-24 UNF 0.63 0.75 0.44 0.38 0.75 2" (200) FRE-5 /2-20 UNF 0.75 0.75 0.44 0.38 0.75 2-/2" (250) 3" (300) FRE-6 5/8-8 UNF 0.88.00 0.63 0.63.00 AT-83