BiWave Hydr DI-9200 User Manual Assembling Hydr DI 9200: Assembling yur BiWave Hydr DI 9200, is a very shrt and simple prcess. All yu have t d is take the Hydr DI 9200 ut f the bx, make sure its standing n a flat level surface, vertically n its bttm end. There are 2 ways t recgnize which side is the bttm f the Hydr DI- 9200: - The tp end has an easily nticeable red warning sticker (read the sticker carefully befre using the Hydr DI 9200). - The pwer crd always cmes ut f the bttm cver. Installing and Running Hydr DI 9200: Fr ptimal results, and t keep yur Hydr DI 9200 under warranty, we advise yu t use the Hydr DI - 9200 in the fllwing way: - Start by making sure the Hydr DI 9200 is placed vertically n its bttm end, secured, leveled, and stable. - The base f the rtating cages shuld be aligned with the tp f the plants, t achieve this it is recmmended t get the adjustable ceiling bracket frm BiWave Industries Inc. designed especially fr the Hydr DI 9200(ask yur retailer hw yu can get ne). As yur plants grw bigger, using the 1
adjustable ceiling bracket will help t keep the base f the rtating cages aligned with the tp f the plants. - If yu are putting the Hydr DI 9200 n the flr, a table, r a shelf, and nt using the adjustable ceiling bracket make sure that the Hydr DI 9200 is secured, leveled, and stable( yu can use a piece f clth r carpet as an insulatr under the Hydr DI - 9200). - It s ptimal t have the Hydr DI 9200 as clse as pssible t the center f the grwing area. - Run the Hydr DI 9200 (fr 15 minutes n, 45 minutes ff, every hur during the light cycle). Yu can use a multi prgram timer fr this purpse. - Keep the Hydr DI 9200 turned OFF during the dark cycle. - Make sure that the adjustable ceiling bracket is attached t the grwing rm r greenhuse ceiling, in a level and stable way, and that the screws that jin the Hydr DI 9200 t the ceiling bracket are tight. After munting plug the Hydr DI 9200 t the timer, plug the timer t a wrking wall utlet, and yu are dne. NOTE: The Hydr DI 9200 must be used thrughut the whle life cycle f the plant. Maintaining Hydr DI 9200: Althugh yur BiWave machine is very easy t use, any machine with mving cmpnents requires peridic maintenance t ensure lngevity and ptimal perfrmance. At least every five mnths yu need t service yur machine, using the fllwing prcedure. 2
1) Discnnect the machine frm the pwer surce/ timer befre perfrming maintenance. 2) It is recmmended but nt necessary t dismunt the Hydr DI 9200 frm any brackets, and place the machine hrizntally n a table. 3) Remve bth end cvers using a 3/16 Allen wrench. 4) Lcate all fur bearings, use a cttn swab r rag t remve any excess grease frm the bearings. 5) Using a grease gun, lcate the brass grease nipple n the side f each bearing. Using multi-purpse lithium grease (ff-white in clr) attach the grease gun t the grease nipple, and begin greasing. Apply grease, until grease begins t verflw ut f the tp f the bearing. D nt add grease past this pint, ver-greasing can be a catalyst fr bearing failure. 6) If the grease just flws ut arund the nipple it means that the nipple is clgged. Get a wrench r scket take the nipple ff and take a paperclip r ther wire and clean ut the nipple. Blw thrugh it t make sure it is n lnger clgged and replace n the bearing. 7) Carefully put the cvers back n t the machine, make sure the cver with the red warning sticker is the tp cver. Be careful f electrnics while putting cvers back n. NOTE: It is imperative t service yur machine. Failure t d s will vid yur warranty. If yu need any help email inf@biwaveindustries.cm r call :( 626) 330-1923 3
BIOWAVE HYDRO D9200 Biwave Prduct Knwledge SLS part # 725900 The Biwave unit is designed t send ut harmnic subsnic frequency levels t the plants, t help the plant breathe better, keeps pests away (hasn t been prven yet), increases CO2 intake, prduces essential ils,and 20% mre yield. The Biwave is preset n a rtatin design t prduce these frequency levels. Testing at Ohi State fr abut 12 t 14 mnths t prve that this unit keeps pests away. CASING: Stainless Steel PACKAGING: Unit cmes in a white display bx. The bx is inside anther bx with 1 fam between the tw bxes. Unit will include instructins, cntact, tech, and trubleshting inf. HEIGHT: 3 x 1 x 1 WEIGHT: 49lbs VOLTS: 120V WATTS: 60 watts UNIT COVERS: 1.5 Acres UPS GROUND: Yes MOUNTING: Munt frm the ceiling in the center f the rm with an adjustable bracket. The unit must be stable. Tp f Biwave unit shuld be flush with the canpy. Munt vertically. The pwer crd cmes ut f the bttm f the unit. Wall munts cming sn. CYCLE: 15 minutes n 45 minutes ff. Apll 6 (734100) Timer is needed. Run the Biwave during light cycle nly. DO NOT RUN WHEN LIGHTS ARE OFF. The BiWave machine is a technlgy that bsts the phtsynthesis in plants, it helps the plants t breathe better during the night there is n phtsynthesis, and there is n need t use the BiWave. And as mst experts shared with us, the plants need t rest during the night, and assimilate the chlrphyll created during the light cycle, and we dn t want t disturb their balance by turning the BiWave machine n.
WARRANTY: 3 year warranty; Excludes custmer misuse f prduct. TECH CALLS: Biwave Industries will take tech calls. Please cntact Gerge r Will @ 626-330-1923 r email @ inf@biwaveindustries.cm. REPAIR: Custmer can repair the unit themselves. It is extremely simple. This will nt vid the warranty. RMA Techs at Sunlight Supply will learn hw t repair this unit. Repair cnsists f mtr, pulley, belt, and cage. If RMA tech at SLS CANNOT repair, Biwave can repair r replace the unit. REPLACEMENT PARTS: Replacement parts will be prvided in the future by SLS. MAINTENANCE: Grease every three t fur mnths. There are nipples n the unit that yu wuld put the grease in. Any grease wuld wrk; t the cheapest grease r the mst expensive grease.
Hydr DI 9200 Trubleshting Starting BiWave: Occasinally ne r bth rtrs n the BiWave Machine wn t start. Try the fllwing: Plug the machine n and wait fr 20 secnds Many BiWave machines start in a sequence, with ne f the rtrs starting between 5-15 secnds after the first ne, if yur BiWave Machine des this; it is n cause fr alarm, just smething t be aware f befre trubleshting in the future. Basic Trubleshting: Is the machine plugged int a wrking utlet/timer? If yu are using a timer try plugging directly int a wall/pwer strip Is the machine munted crrectly? BiWave must be munted vertically with the bttm cver pinted t the flr, and the tp cver pinted twards the ceiling The BiWave Machine has a tp and bttm, there are a cuple f ways t check if it is munted crrectly: The tp is labeled n the frnt with a red sticker The wall chrd always cmes ut f the bttm cver Make sure yur BiWave Machine is level Advanced Trubleshting: Pwer the machine n If the interir (smaller) rtr will nt spin, the issue is under the bttm cver If the exterir (bigger) rtr will nt spin, the issue is under the tp cver Pwer the machine ff, based n which rtr it is yur fcus shuld g t the crrespnding cver fr the rest f yur trubleshting Fcus n the green light in the pwer supply (lcated under the tp cver), pwer the machine n If the light des nt turn whatsever the issue is electrical, if the light turn n the issue is mechanical, if the light nly turns a little bit withut staying n, the issue may be either electrical r mechanical. Pwer the machine ff, unplug the machine, carefully, lay the machine dwn n a flat surface, the wide side dwn. Use a 3/16 Allen wrench t remve the cver f the affected side, this is dne by remving the tw screws lcated n each side f the cver
If the light did nt turn n ( did nt turn at all) in the preceding test,check the fllwing: With the cver nw ff, are there any lse/bare (uncnnected) wires? Check the plug that cnnects int the pwer supply, unplug the wire, and plug-it back in, make sure that it is all the way plugged in. Yu can test if this is the slutin with the cver ff and the machine lying dwn. If the light still will nt turn at all it is likely that the pwer supply is defective, r the pwer cable has been damaged. If this is the case, cntact BiWave. If the light is turning but the rtr is nt turning OR the light turns a little bit but des nt cntinue t rtate check the fllwing: The prblem is mst likely an issue with the tensin f the timing belt, befre prceeding MAKE SURE the BiWave Machine is unplugged. The timing belt can be t tight r t lse, bth can cause the rtr t nt spin. Here is hw yu tell: Pinch the belt with yur thumb and frefinger the belt shuld have tensin withut any pressure frm pinching. Yu shuld be able t pinch (with relative ease), cnstricting the belt just inside the diameter f either pulley (it shuld nt pinch further than 2/3 s f the diameter f the pulley). If yu can t pinch it t this pint (r it is difficult t pinch) the belt is t tight, if yu can pinch it past 2/3 s diameter (especially if it is very easy) the belt is t lse. If the belt tensin is perfect and still nt wrking, cntact BiWave. If the belt needs t be adjusted cntinue fllwing the directins Lk at the belt, if any part f it is frayed r has hles, then the belt is damaged and needs t be replaced, If yu need anther belt r are changing the belt, cntact BiWave we will help yu find what caused the damage t the belt and/r prvide yu with a new ne. T change the tensin n the belt, take the fllwing steps: Lsen the blts that cnnect the mtr munts t the endplate (these blts are n the rtr side f the endplate, are visible with the cver n, and pass thrugh the tensining slts n the endplate). Lsen all three blts. They dn t need t be unscrewed all the way, an 1/8 th f an inch is plenty, and will make reassembly much easier. OPTIONAL: while yu have these blts lse, it will give yu a chance t check the integrity f the pulley n the mtr (this culd be the cause f yur prblem) If yu want t check this read the next set f bullet pints therwise skip ahead Slide the mtr alng the tensining slts all the way frward (twards the frnt f the machine) the belt shuld fall ff r becme very lse Pull the belt ff Push the bttm f the pulley with yur index finger with LIGHT pressure if the pulley mves easily, it is either damaged, r defective, cntact BiWave immediately if this is the case If the belt is t lse slide the mtr twards the back f the machine, if it is t tight than slide the mtr twards the frnt f the machine. Yu wn t need t slide it t far in either directin, a little bit ges a lng way. When yu believe yu ve reached the right level f tensin, tighten the 3 blts that yu
lsened, as yu tighten the blts check the tensin n the belt because it WILL change, s adjust accrdingly. Befre putting the cver back n make sure all blts are tight. While putting the cver back n, make sure all f the wires are under the cver, and nt clse t any mving parts f the machine, slide the cver ver the tabs, insert screws, tighten, and put yur BiWave back t wrk. Yu may want t cntact BiWave t set up a service call. Yu may als chse t prceed n yur wn, please be aware if yu chse t prceed n yur wn; yu d s at yur wn cautin. If yu d nt fllw the directins carefully yu culd cause irreparable damage t the BiWave Machine rendering any warranties vid. Fr all service inquiries cntact BiWave Industries Inc. r yur BiWave retailer: Please have the name and mdel f yur Machine ready. Inf@Biwaveindustries.cm Or call 626-330-1923