SHEET 1 of 9 DESIGN HIGHLIGHTS Effortless, one handed operation; even with heavy screens Bracket allows perfect parallel tracking before screen is rotated FUNCTION A manual wall bracket that allows simple one handed movement of the screen. Bracket allows perfect parallel tracking before being rotated in either direction up to 60. Bi-directional swivel motion up to 60 Strong steel construction Wide range of mounting options Excellent service bracket allows for installation in tight recesses SUITABILITY The PS42 wall bracket is suitable for screens from 42" up to 50". Up to a maximum weight of 40Kg [88lbs] Larger screens can be installed but maximum possible angles of rotation would be reduced. OPTIONS Bang & Olufsen / Loewe mount options The larger PS50 wall bracket is suitable for 50" to 60" screens. Compatible accessories such as In-Wall Boxes and speaker mounts SPECIFYING Check wall makeup to decide on fixings to be used. Check screen details for mounting possibilities. Check angles for viewing. WARNING It is the responsibility of the installer to make sure the product is safely secured to the wall IMPORTANT Mechanisms which lift or move weights need to be checked on a yearly basis for any damage which may result in an accident
SHEET 2 of 9 Design Highlights VIEWS BELOW SHOW MOVEMENT FROM IN POSITION TO MAXIMUM ANGLE OF 60 Bracket design allows for screen to track parallel to wall before being rotated. This allows the screen to be mounted within a tight recess if required. Bracket design means minimal effort is required to move even heavy screen and speaker installations. 420 16.5 Bracket allows for up to 60 degrees of swivel in either direction. This angle is reduced when wider screens or additional side speakers are installed. Bracket capable of maximum horizontal mounting distances of 400mm [15.7"] and maximum vertical mounting distances of 470mm [18.6"]. Mechanism allows up to 420mm [16.5"] extension of screen centre from mounting surface.
Screen Mounting Procedure SHEET 3 of 9 STEP 1 STEP 3 Remove the Screen Mount and secure to the rear of the screen using the rear fixings. 15 0.6 Lower the screen so that the Hook Pins sit inside the Top Bar Plate and slide the screen mount underneath the Bottom Bar Plate. 15 0.6 A BAR PLATE BOTTOM Slots allow for 15mm [0.6"] horizontal position adjustment. DETAIL A SCALE 1 : 2 C DETAIL C SCALE 1 : 2 SCREEN MOUNT STEP 2 Tilt the screen forwards and align the Hook Pins with the holes in the Top Bar Plate. STEP 4 Fix the screen mount in place by screwing 2 x M6 bolts into the Bottom Bar Plate. B BAR PLATE TOP BAR PLATE BOTTOM HOOK PIN DETAIL B SCALE 1 : 2 D DETAIL D SCALE 1 : 2
Cable Routing Options SHEET 4 of 9 Run the cables up to either top corner of the wall bracket, loop over and run down the out side of the scissor leg as shown with the red line. Secure the cables using cable ties and make sure to allow slack at moving points. OUTER SCISSOR LEG WALL BRACKET POWER / AUX CABLES
SHEET 5 of 9 Screen Mounting - Dimensions Remove the screen uprights and secure to the rear of the screen using the rear fixings, then offer the screen back onto the bracket and fix in place. 43 1.7 340 13.4 28 1.1 170 6.7 170 6.7 420 16.5 MAXIMUM HORIZONTAL MOUNTING DISTANCE 400 15.7 107 4.2 MIN 70 2.8 MAXIMUM VERTICAL MOUNTING DISTANCE 470 18.5 537 21.1 SCREEN UPRIGHTS
Bracket Movement - Dimensions SHEET 6 of 9 Top view showing maximum movement of bracket. 60 degree rotation may be reduced with a very wide screen installations. Very smooth one hand operation. 70 2.8 341 13.4 420 16.5 60 60 340 13.4
Wall Plate - Dimensions SHEET 7 of 9 Wall plate mount fixing dimensions. Make sure the wall which the bracket is being mounted to is secure and strong enough to support the bracket and screen. 220 8.7 180 7.1 C L 16 0.6 100 3.9 130 5.1 513 20.2 6 x 10 0.4 THRU 260 10.2 2 x 6 0.2 THRU 130 5.1 23 0.9
Bracket Only Recess Mounting SHEET 8 of 9 When recessing the bracket into the wall its important to allow 20mm [0.8"] gap around the sides and bottom of the bracket. A 50mm [2"] gap is required at the top to allow the screen mount to be hooked on/off the bracket. A 26 1.0 26 1.0 70 2.8 40 1.6 590 23.2 20 0.8 392 15.4 A SECTION A-A
Screen Recess Mounting SHEET 9 of 9 When recessing the screen into the wall its important to allow 50mm [2"] gap around the perimeter to allow screen ventilation, this gap can be reduced if the recess design caters for ventilation requirements. Power and signal cables should exit somewhere in the recess to keep cables out of view B 50 2.0 50 2.0 50 2.0 Screen Height + 100mm [3.9"] 50 2.0 Screen Width + 100mm [3.9"] Screen Depth + 70mm [3.1"] B SECTION B-B