Veetia blid motor: GEGER-GJ56..e with electroic ed stop For Veetia blids ad exterior blids DE FR ES T Origial-Motage- ud Betriebsaleitug Origial assembly ad operatig istructios Notice origiale de motage et d utilisatio struccioes origiales de istalació y fucioamieto struzioi origiali di istallazioe e fuzioameto www.geiger.de 1
dex 1. Geeral iformatio...2 2. Guaratee...2 3. teded use...2 4. Safety istructios...3 5. Safety istructios for assembly...3 6. Assembly ote...4 7. stallatio istructios...5 8. formatio for the specialist electricia...6 9. Cotrol features...6 10. Settig of the ed stops...7 11. Operatio...9 12. What to do if...9 13. Maiteace...9 14. Techical data...10 15. Declaratio of coformity... 11 16. Notes o waste disposal...12 1. Geeral iformatio Dear customer, By purchasig a GEGER motor you have decided o a quality product from GEGER. Thak you very much for your decisio ad the cofidece placed i us. Before you put this drive ito operatio please observe the followig safety istructios. t serves for the prevetio of dager ad for the avoidace of persoal ijury ad damage to property. The istallatio ad operatig istructios cotai importat iformatio for the istaller, the specialist electricia ad the user. Please pass o these istructios if you trasfer the product. These istructios should be kept by the user. 2. Guaratee the case of icorrect istallatio cotrary to the istallatio ad operatig istructios ad/ or costructioal modificatio, the legal ad cotractual guaratee for property damage ad product liability lapses. 3. teded use The motors of the model rage GJ56..e with electroic ed stop are desiged exclusively for the operatio of Veetia blids. The motors may ot be used for the operatio of roller grilles, garage doors, furiture ad liftig tools. GJ 56 xx x Desig optios Torque i Nm For head rails at least 56 mm GEGER Veetia blids motor 2 Gerhard Geiger GmbH & Co. KG 100W1503e V001 0517
4. Safety istructios ATTTON: mportat safety istructios. For persoal safety, it is importat to follow these istructios. Please keep these istructios for future referece. Do ot allow childre to play with statioary cotrols. Keep remote cotrols away from childre. The istallatio is to be checked regularly for defective balace, sigs of wear or damaged cables ad sprigs, if relevat. Do observe the movig su protectio system ad keep persos away util it has closed completely. Whe operatig the maual release with the su protectio system ope, please be cautious as it ca fall dow quickly if sprigs or tapes wear o or are broke. Do ot operate the device if operatios such as, for example, widow cleaig are to be carried out i the viciity. Discoect the automatic cotrolled device from the mais power supply if operatios such as, for example, widow cleaig are beig carried out i the viciity. Durig operatio observe the dager zoe. Do ot use the istallatio if people or objects are i the dager zoe. Urgetly shut dow damaged istallatios util repair. Ucoditioally shut dow the uit durig maiteace ad cleaig operatios. Pichig ad shearig poits are to be avoided ad must be secured. This appliace ca be used by childre aged 8 ad above ad persos whose physical, sesorial or metal capacities are impaired, or who have o experiece or kow-how if they have bee supervised or bee give istructios o the use of the appliace ad if they uderstad the possible resultig dagers. Childre are ot permitted to play with the device. Cleaig ad maiteace should ot be carried out by childre. The rated soud pressure level is less tha 70 db(a). Discoect the device from the mais power supply for maiteace ad replacemet of parts. f the motor is discoected via a plug coectio the operator must be able to cotrol - from ay place to which it has access that the plug is removed. f this is ot possible - due to desig or istallatio - the discoectio from the power supply must be esured via lockig i the discoected positio (e.g. isolator). The motor tube ca get very hot durig prologed use. Whe workig o the uit, do ot touch the tube before it has cooled dow. 5. Safety istructios for assembly ATTTON: mportat safety istructios. Follow all istallatio istructios, as icorrect istallatio ca lead to serious ijuries. Whe moutig the motor without ay mechaical protectio of the drive parts ad of the tube which may become hot, the motor must be istalled at a height of at least 2.5 m above the groud or of aother level which provides access to the drive. Before the motor is istalled, all cables which are ot eeded are to be removed ad all equipmet which is ot eeded for power-operated actuatio is to be put out of operatio. The actuatig elemet of a maual release must be mouted at a height of less tha 1.8 m. f the motor is cotrolled by a switch or pushbutto, the switch or pushbutto must be mouted withi eyeshot of the motor. The switch or pushbutto must ot be located i the viciity of movig parts. The height of istallatio must be at least 1.5 m above the floor. Permaetly istalled cotrol devices must be attached visibly. case of devices extedig horizotally, a horizotal distace of at least 0.4 m must be respected betwee the fully exteded part ad ay other fixed elemet. www.geiger.de 3
The rated speed ad the rated torque of the motor must be compatible with the device. The moutig accessories that are used must be desiged i accordace with the selected rated torque. Good techical kowledge ad good mechaical skills are ecessary for the motor istallatio. correct istallatio ca lead to serious ijury. Electrical work must be carried out by a qualified electricia i accordace with the regulatios i force locally. Oly use coectig cables that are suitable with the evirometal coditios ad which meet the costructio requiremets. (see accessories catalogue) f the device is ot equipped with a coectig cable ad a plug, or other meas for discoectig from the mais with a cotact opeig o each pole accordig to the coditios of the overvoltage category for full discoectio, a discoectig device of this type must be icorporated ito the permaetly istalled electrical istallatio accordig to the wirig rules. Do ot mout the coectig cables ear hot surfaces. A plug for the discoectio of the motor from the power supply must be accessible after istallatio. Damaged coectig cables must be replaced by GEGER coectig cables of the same type. The device must be mouted as described i the istallatio istructios. Fixatios shall ot be made with adhesives sice they are regarded as ureliable. 6. Assembly ote Whe viewed from iside the room, the power supply coectio of the GJ56..e is located o the left side. The straps are woud o the widig rollers from the outside. The GJ56..e must be istalled i aligmet with the turig bars. t is importat that the GJ56..e is istalled cetrally. Please make sure that the load is evely distributed. clied istallatio: The iclied istallatio is permitted till 45 maximum to level. Directio OP Electric mais side the room 4 Gerhard Geiger GmbH & Co. KG 100W1503e V001 0517
7. stallatio istructios Prior to istallatio please check to esure there is o visible damage to the motor like cracks or ope cables. Before fixig please check the stregth of the masory ad of the surface. www.geiger.de 5
8. formatio for the specialist electricia H Cautio: mportat istallatio istructios. Please follow all istallatio istructios sice icorrect istallatio ca lead to the destructio of the motor ad the switchig uit. e1-e4: the settig of the ed stops requires a GEGER settig switch e5: the settig ca be realized with ay switch allowig simultaeous UP ad DOWN cotrols. e1-e4: a o-lockig switch (series switch) is eeded i order to reach the shade positio. See poit 10 Operatio. e5: a lockig switch is here ecessary (o simultaeous UP ad DOWN commads) The operatios with the service clamps may be accomplished oly by a electrical specialist. Motors with electroic limit stops ca be coected i parallel. this case the maximum load of the switchig uit must ot be exceeded. Whe chagig the ruig directio the switchover must be eected through a o-positio. Whe chagig the ruig directio the switchover time must be at least 0.5 s. With a three-phase etwork, please use the same exteral coductor i order to cotrol the UP ad DOWN directios. Coectig cables with plug coectors of the Hirschma Compay are tested ad approved with coupligs of the Hirschma Compay. order to prevet a malfuctio caused by couplig, the supply lie (ref. NYM) from the actuator/switch to the motor must ot exceed 100m i case of motors with electroic ed stops. L1 N PE Mais: 230V / 50Hz PE gree/yellow N 1 2 3 blue brow black Electroic / mechaical limit stop 9. Cotrol features Electroic motor cotrols features direct shade positio The blid always moves to the lower ed positio first, turs roud there ad moves to the shade positio. Direct shade positio The blid moves directly to the shade positio Preset shade positio 0,5 rotatios over the lower ed positio Atifreeze protectio 2 rotatios from the lower ed positio Torque shut-dow i UP directio Set up i learig mode Oly the upper ed positio has to be leared e1 e2 e3 e4 e5 A GEGER settig switch is required Exteral settig switch A switch which allows simultaeous UP ad DOWN commads is ecessary 6 Gerhard Geiger GmbH & Co. KG 100W1503e V001 0517
10. Settig of the ed stops Motors GF56..e1 e4: a GEGER settig switch is required for the settig of the ed stops Motors GF56..e5: the settig ca be realized with ay switch allowig simultaeous UP ad DOWN commads. Part-Nr. / GEGER settig switch M56K144 With Hirschma STAK3 coector (D) M56F150 With Hirschma STAK3 coector (CH) M56F151 With termial (D) M56B265 Adaptatio cable with termial ad STAS3 M56E399 Adaptatio cable with STAK3 ad ope cable eds Readjustmet of the ed stops The readjustmet of the ed stops ca be carried out at ay time i accordace with the istructios give below. f there is o ruig of the blid by the operatio poits 3, 5 ad 7 the ed stops have kept the same positio as before. Shade positio/workig positio (oly e1 e4) The shade positio/workig positio ca be reached by actuatig both directio keys at the same time Overload recogitio The overload recogitio is adapted to the give torque (+ safety margi) of the Veetia blid system by carryig out the complete adjustmet procedure. The blid must be moved by steps 3, 5 ad 7. Settig GJ56..e1, e2 ad e3 The order of the adjustmet process must be strictly adhered to ad the adjustmet must always be completely implemeted (all steps). The motor GJ56..e3 is set up with a learig mode. Durig assembly please begi the settig with step 1 ad the go over to step 7. 1. Coect the settig switch to the GJ56..e ad the plug i power supply 2. Press the programmig butto till the LED flashes (1 flash light, break, 1 flash light, break, ) the release the programmig butto. 3. Settig of the lower ed stop: press the directio keys to exactly ru the GJ56..e to the desired lower ed positio. 4. Press the programmig butto till the LED flashes (2 flash lights, break, 2 flash lights, break, ) the release the programmig butto 5. Settig of the shade positio/workig positio: press the directio keys to exactly ru the GJ56..e to the desired positio. 6. Press the programmig butto till the LED flashes (3 flash lights, break, 3 flash lights, break, ) the release the programmig butto 7. Settig of the upper ed positio: press the directio keys to exactly ru the GJ56..e to the desired upper ed positio. 8. Press the programmig butto till the LED keeps lightig. The adjustmet procedure is completed. www.geiger.de 7
Settig GJ56..e4 The order of the adjustmet process must be strictly adhered to ad the adjustmet must always be completely implemeted (all steps). The motor GJ56..e4 is set up with a learig mode. Durig assembly please begi the settig with step 1 ad the go over to step 7. 1. Coect the settig switch to the GJ56..e ad the plug i power supply 2. Press the programmig butto till the LED flashes (1 flash light, break, 1 flash light, break, ) the release the programmig butto. 3. Settig of the lower ed positio: press the directio keys to exactly ru the GJ56..e to the desired lower ed positio. 4. Press the programmig butto till the LED flashes (2 flash lights, break, 2 flash lights, break, ) the release the programmig butto 5. Settig of the shade positio: press the directio keys to exactly ru the GJ56..e to the desired positio. 6. Press the programmig butto till the LED flashes (3 flash lights, break, 3 flash lights, break, ) the release the programmig butto 7. Ru the blid to the upper ed positio. The motor turs o via torque recogitio. 8. Press the programmig butto till the LED keeps lightig. The adjustmet procedure is completed. Settig GJ56..e5 The order of the adjustmet process must be strictly adhered to ad the adjustmet must always be completely implemeted (all steps). 1. Coect the settig switch to the GJ56..e ad the plug i power supply 2. Press the programmig butto till the LED flashes (1 flash light, break, 1 flash light, break, ) the release the programmig butto. 3. Settig of the lower ed positio: press the directio keys to exactly ru the GJ56..e to the desired lower ed positio. 4. Press the programmig butto till the LED flashes (2 flash lights, break, 2 flash lights, break, ) the release the programmig butto 5. Settig of the upper ed positio: press the directio keys to exactly ru the GJ56..e to the desired upper ed positio. 6. Press the programmig butto till the LED keeps lightig. The adjustmet procedure is completed. Whe usig a exteral settig switch, the UP ad DOWN keys must be activated simultaeously istead of the programmig key. stead of the lightig up of the LED, the motor reacts with a short back ad forth movemet. 8 Gerhard Geiger GmbH & Co. KG 100W1503e V001 0517
11. Operatio f the shade positio/workig positio is ot used, the GJ56..e ca be operated with a stadard locked Veetia blid switch. f the shade positio/workig positio is used (e1-e4) a series switch which allows simultaeous UP ad DOWN commads is ecessary. The operatio is eected as described below: Actuate the key UP to ru the motor to the upper ed positio Actuate the keys UP ad DOWN at the same time to ru the motor to the shade positio/workig positio (e1-e4) Actuate the key DOWN to ru the motor to the lower ed positio 12. What to do if Problem Motor does ot ru. stead of i the upwards directio, motor rus dowwards. Motor oly rus i oe directio. After ruig several times, the motor breaks dow ad o loger respods. After settig of the lower ed positio the blid oly rus i DOWN directio. Solutio Motor ot plugged i. Please check the plug coectio. Check coectig cable for possible damage. Check the mais voltage ad allow the cause of the voltage break dow to be tested by a specialist electricia. The cotrol leads are iterchaged. Exchage black/brow cotrol leads. Motor i the ed positio. Ru motor i the opposite directio. Readjust teh ed positios, if ecessary. The motor became too hot ad has switched o. Try it agai after a coolig time of about 15 mi. The motor has bee istalled upside dow (see assembly ote). 13. Maiteace The drive is maiteace-free. www.geiger.de 9
geprüfte Sicherheit geprüfte Sicherheit 14. Techical data Techical data GJ56..e with electroic ed stop (stadard electroic) Voltage GJ5603ke GJ5606ke GJ5610e GJ5618e 230 V~/50 Hz Curret 0,40 A 0,40 A 0,60 A 0,80 A Cos Phi (cosj) > 0,95 rush curret (factor) x 1,2 Power 90 W 93 W 135 W 180 W Torque 3 Nm 6 Nm 10 Nm 2 x 9 Nm Speed 26 rpm Protectio class P 54 Limit switch rage Operatig mode 200 rotatios S2 4 mi Soud pressure level 1) 34 db(a) 34 db(a) 35 db(a) 40 db(a) Legth 301 mm 301 mm 311 mm 338 mm Diameter 55 mm Weight approx 1,50 kg approx 1,50 kg approx 1,70 kg approx 2,20 kg Storage temperature/ T = -15 C.. +70 C / dry ad o-codesig place Humidity Subject to techical modificatios DE V Techical data GJ56..e with electroic ed stop (ru-time optimized versio) GJ5606e GJ5616e Voltage 230 V~/50 Hz Curret 0,40 A 0,70 A Cos Phi (cosj) > 0,95 rush curret (factor) x 1,2 Power 90 W 150 W Torque 6 Nm 2 x 8 Nm Speed 26 rpm Protectio class P 54 Limit switch rage 200 rotatios Operatig mode S2 6 mi Soud pressure level 1) 34 db(a) 40 db(a) Legth 306 mm 338 mm Diameter 55 mm Weight approx 1,60 kg approx 2,20 kg Storage temperature/ T = -15 C.. +70 C / dry ad o-codesig place Humidity 1) The average soud pressure level data are iteded for guidace oly. The values were determied by GEGER at a distace of 1 m, with a hagig motor at idle speed ad averaged over 10 secods. There is o referece to ay specific test stadard. Subject to techical modificatios DE V 10 Gerhard Geiger GmbH & Co. KG 100W1503e V001 0517
15. Declaratio of coformity EU Declaratio of Coformity Gerhard Geiger GmbH & Co. KG Atriebstechik Schleifmühle 6 D-74321 Bietigheim-Bissige Product desigatio: Veetia blids motor, motor for rollig shutters, motor for awigs Type desigatio: GJ56.. GR45.. GU45.. GS56.. Applied directives: 2006/42/EC 2014/30/EU 1999/5/EC 2011/65/EU Applied stadards: DN 60335-1 DN 60335-2-97 DN 62233 DN 55014-1 DN 55014-2 DN 61000-3-2 DN 61000-3-3 ETS 300 220-2 ETS 301 489-1 ETS 301 489-3 Authorized represetative for techical data: Gerhard Geiger GmbH & Co. KG Address: Schleifmühle 6, D-74321 Bietigheim-Bissige 100W1518 e 0117 Bietigheim-Bissige, 02.01.2017 Dr. Marc Natusch (Geeral Maager) Curret declaratios of coformity are available uder www.geiger.de www.geiger.de 11
16. Notes o waste disposal Recyclig of packagig materials the iterest of evirometal protectio, please cotact your local govermet s recyclig or solid waste maagemet departmet to lear more about the services it provides. Waste disposal of electric ad electroic equipmet Electrical ad electroic equipmet must be collected ad disposed of separately i accordace with EU regulatios. For techical questios, please call our service team at: +49 (0) 7142 938-333. They will be happy to assist you. Gerhard Geiger GmbH & Co. KG Schleifmühle 6 D-74321 Bietigheim-Bissige Telephoe: +49 (0) 7142 938-0 Telefax: +49 (0) 7142 938-230 E-Mail: ifo@geiger.de teret: www.geiger.de 12 Gerhard Geiger GmbH & Co. KG 100W1503e V001 0517