INSTALL GUIDE COM-CH(RS)-CH5-[FT-CH5-DC]-EN

INSTALL GUIDE DOCUMENT NUMBER 89 REVISION DATE 707 FIRMWARE COM-CH(RS)-CH-[FT-CH-DC] HARDWARE FT-CH-DC ACCESSORIES ADS-USB (REQUIRED) COMPATIBLE RF-KIT (OPTIONAL) DRONE MOBILE DR-000 (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 7 BEFORE INSTALLATION - Connect module to computer - Login to Weblink account - Flash firmware to module (module is not preloaded with firmware) - Use accessories accordingly (accessories are sold separately)

PAGE OF DOC.: #89 707 VEHICLE LIST - OF FEATURES MODEL YEAR DATA IMMOBILIZER BYPASS X LOCK START/STANDALONE MOD. PRIORITY UNLOCK DOOR LOCK DOOR UNLOCK ARM OEM ALARM DISARM OEM ALARM TRUNK/HATCH RELEASE DATA/MUX STARTER CTRL DOOR STATUS BRAKE PEDAL STATUS TACHOMETER STATUS PARKING LIGHT CTRL* RAP SHUTDOWN CTRL WARNING 00 AT - 00 / 00C AT 0-07 or Aspen AT 07-0 PT Cruiser AT 0-0 or CHRYSLER INSTALL TYPE MAKE I Install Type requires a T-harness manufactured before //0 Install Type requires a T-harness manufactured after //0 07-0 08- Caliber (with start wire) AT 07 Caliber AT 07- Charger AT 0-07 or Durango AT 07-0 Magnum AT 0-07 or Nitro AT 07- Ram 00 AT 07-08 Ram 00 AT 07-09 Ram 00 AT 07-09 Ram 00 chassis cab AT 07-09 Ram 00 chassis cab AT 08-0 Ram 00 chassis cab AT 08-0 Commander AT 0-07 or Compass AT 07-7 Grand Cherokee AT 0-07 or Liberty AT 08- Patriot AT 07-7 Wrangler AT 07-7 00 chassis cab AT 0 00 chassis cab AT * May require additional parts. 0 RAM JEEP DODGE Sebring AT Avenger AT Automotive Data Solutions Inc. 7 or

PAGE OF DOC.: #89 707 BOX CONTENTS - OF BOX CONTENTS MODULE LED BLUE BLACK BLACK 0 PIN T-HARNESS 8 0 8 0 7 9 7 9 8 0 7 9 PROGRAMMING BUTTON LED A G F B E BLACK RF PORT/ WEBLINK PORT BLUE TELEMATIC PORT BLACK MS VS PIN VS MS AFTERMARKET HOOD SWITCH AND CABLE C D 9 0 7 8 WHITE WARNING STICKER WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE WEBLINK PORT COMPUTER USB PORT PIN BLACK CABLE Automotive Data Solutions Inc. 7

PAGE OF DOC.: #89 707 COMPATIBLE ACCESSORIES - OF RF KIT (Visit our website to see if this accessory is included with your product) RF KIT FLASH RF DECODER BEFORE INSTALLATION (NC) RED (NC) BLACK BLUE MODULE RF PORT BLACK BLUE CABLE RF DECODER BLACK CABLE ANTENNA TELEMATIC KIT (accessory sold separately) DRONE MODULE TELEMATIC PORT Automotive Data Solutions Inc. 7 (NC)

PAGE OF DOC.: #89 707 COMPONENT LOCATOR Pink/DkGreen White/ Passenger kick panel Pink/LtBlue White/ Brown/Tan Pink/DkGreen 07 Parking Light* White/ /Blue Pink/DkGreen White/ Passenger kick panel Pink/DkGreen White/ Passenger kick panel Pink/Orange 8 Parking light relay, engine compartment. Pink/Orange White/ Parking light relay, engine compartment. /Blue 0-07 Parking Light* 0-07 Parking Light* 0-07 Parking Light* 0-07 Parking Light* NAME MODULE LOCATION WIRE DESCRIPTION POLARITY Grand Cherokee 0-0 Parking Light* JEEP Commander WIRE COLOR Magnum POSITION Charger TYPE DODGE Caliber (with start wire) COLOR PT Cruiser 0-07 Parking Light* CHRYSLER 00/00C YEAR MODEL MAKE TYPE - WIRE CHART - OF * Requires additional parts. Automotive Data Solutions Inc. 7

PAGE OF DOC.: #89 707 TYPE - WIRING DIAGRAM - OF MODULE VEHICLE IGNITION SWITCH A G RF PORT/WEBLINK PORT B F TELEMATIC PORT E C D A VS SKIM NOTE REMOVE THE WHITE/GREEN WIRE FROM THE BLUE AND RE-INSERT IT IN PIN (AS SHOWN) (SEE DETAILED INSTRUCTIONS ON THE NEXT PAGE) A CUT AND INSULATE THE WHITE/YELLOW WIRE (NEXT TO WHITE/GRAY WIRE) WARNING THIS WIRING DIAGRAM IS APPLICABLE ONLY IF THE REVISION DATE OF THE T-HARSNESS IS BEFORE: //0 A VS SKIM HARNESS MS 0 WHITE/RED 0 WHITE/GREEN B B NOTE 8 0 8 0 7 9 7 9 PURPLE - STARTER OUTPUT WHITE/YELLOW - CONTROL OUTPUT STARTER - 0 CONTROL - 0 CONNECT THE WHITE/GREEN WIRE TO THE PINK WIRE AND CONNECT THE WHITE/RED WIRE TO THE RED WIRE (SEE DETAILED INSTRUCTIONS ON THE NEXT PAGE) A MS B WHITE/GREEN WHITE/RED WHITE/BROWN (NC) INSULATE WIRE 0 PINK 0 RED C 8 7 0 9 BROWN/BLACK - PARKING LIGHT OUTPUT 0 GRAY - RAP SHUTDOWN OUTPUT VEHICLE PARKING LIGHT CONNECTION GRAY/GREEN - HORN OUTPUT CONNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT 0 AMPS D V OR 8 0 7 9 0 GRAY/WHITE - HOOD STATUS INPUT CONNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH PARKING LIGHT 8 87 8 87A 0 PARKING LIGHT OPTIONAL DRIVER DOOR PIN HORN AFTERMARKET HOOD SWITCH Automotive Data Solutions Inc. 7

TYPE - WIRING DIAGRAM - OF NOTE PAGE 7 OF DOC.: #89 707 NOTE STEP : -REMOVE THE WHITE/GREEN WIRE FROM THE BLUE CAREFULLY. -USE A UTILITY KNIFE TO PUSH GENTLY AGAINST THE LOCKING TAB. -DO NOT DAMAGE THE LOCKING TAB IN THE PROCESS. STEP : -IDENTIFY THE PINK (PIN 7) AND RED (PIN 9) WIRES FROM THE 0 PIN BLACK OF THE T HARNESS. -CAREFULLY STRIP THE PINK AND RED WIRES USING A WIRE STRIPPER. -DO NOT CUT THE WIRES IN THE PROCESS. WHITE/RED WHITE/GREEN STEP : -USING A UTILITY KNIFE, LIFT THE LOCKING TAB CAREFULLY FOR IT TO BE RE-USED. STEP : -CONNECT AND SOLDER THE WHITE/RED WIRE TO THE RED WIRE. -CONNECT AND SOLDER THE WHITE/GREEN WIRE TO THE PINK WIRE. WARNING FAILURE TO PROPERLY SOLDER CAN RESULT IN FAULTY CONNECTIONS AND PRODUCT MALFUNCTION STEP : -INSULATE THE CONNECTIONS WITH ELECTRICAL TAPE. STEP : -INSERT THE WIRE IN PIN OF THE, RIGHT NEXT TO WHERE IT USED TO BE. WHITE/RED WHITE/GREEN Automotive Data Solutions Inc. 7

PAGE 8 OF DOC.: #89 707 COMPONENT LOCATOR - Parking Light* White/ Pink/Red Violet Driver door module /Blue 07-0 Parking Light* White/ 08- Parking Light* White/ 07- Parking Light* White/ /Blue 07-0 Parking Light Nitro NAME MODULE LOCATION WIRE DESCRIPTION Durango DODGE POLARITY Caliber WIRE COLOR DODGE Avenger POSITION Sebring TYPE Aspen COLOR CHRYSLER 00 YEAR MODEL MAKE TYPE - WIRE CHART - OF Pink/Red Violet Driver door module 07- Parking Light* White/ + White/Green 07-0 Parking Light * Requires additional parts. Automotive Data Solutions Inc. 7

PAGE 9 OF DOC.: #89 707 WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR White/Green White/Green White/Green White/Green White/Green 07-7 Parking Light* White/ /Blue /Blue 08- Parking Light* White/ 07-09 Parking Light 07-09 Parking Light 07-09 Parking Light 08-0 Parking Light 08-0 Parking Light JEEP Compass POSITION Ram 00 TYPE Ram 00 COLOR Ram 00 NAME DODGE Ram 00 WIRE DESCRIPTION Ram 00 YEAR MODEL MAKE TYPE - WIRE CHART - OF Liberty * Requires additional parts. Automotive Data Solutions Inc. 7

PAGE 0 OF DOC.: #89 707 TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR 07-7 Parking Light* White/ /Blue 07-7 Parking Light* White/ + White/Orange Passenger kick pad Parking Light White/Green Parking Light White/Green 0 RAM 00 00 0 NAME COLOR Wrangler WIRE DESCRIPTION JEEP Patriot YEAR MODEL MAKE TYPE - WIRE CHART - OF * Requires additional parts. Automotive Data Solutions Inc. 7

PAGE OF DOC.: #89 707 TYPE - WIRING DIAGRAM - OF MODULE VEHICLE IGNITION SWITCH A G RF PORT/WEBLINK PORT B F TELEMATIC PORT A VS SKIM E C D A VS SKIM HARNESS A 8 0 8 0 7 9 7 9 MS A B MS PURPLE (NC) WHITE/YELLOW (NC) VEHICLE PARKING LIGHT CONNECTION WHITE/BROWN - PARKING LIGHT OUTPUT CONNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT PARKING LIGHT OR CONNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT C 8 7 0 9 0 AMPS V OR BROWN/BLACK - PARKING LIGHT OUTPUT 0 GRAY - RAP SHUTDOWN OUTPUT CONNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT GRAY/GREEN - HORN OUTPUT PARKING LIGHT 8 87 8 87A 0 PARKING LIGHT D 8 0 7 9 OPTIONAL 0 GRAY/WHITE - HOOD STATUS INPUT DRIVER DOOR PIN HORN WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH AFTERMARKET HOOD SWITCH Automotive Data Solutions Inc. 7

PAGE OF DOC.: #89 707 TYPE - WIRING DIAGRAM - OF MODULE VEHICLE IGNITION SWITCH A G RF PORT/WEBLINK PORT B F TELEMATIC PORT E C CUT AND INSULATE THE WHITE/YELLOW WIRE (NEXT TO WHITE/GRAY WIRE) WARNING THIS WIRING DIAGRAM IS APPLICABLE ONLY IF THE REVISION DATE OF THE T-HARSNESS IS AFTER: A VS D SKIM //0 A A VS SKIM HARNESS MS B B PURPLE - STARTER OUTPUT WHITE/YELLOW - CONTROL OUTPUT 8 0 8 0 7 9 7 9 STARTER - 0 CONTROL - 0 MS A B C VEHICLE PARKING LIGHT CONNECTION 8 7 0 9 BROWN/BLACK - PARKING LIGHT OUTPUT 0 GRAY - RAP SHUTDOWN OUTPUT WHITE/BROWN - PARKING LIGHT OUTPUT CONNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT PARKING LIGHT OR GRAY/GREEN - HORN OUTPUT CONNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT 0 AMPS D V OR 8 0 7 9 0 GRAY/WHITE - HOOD STATUS INPUT CONNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH PARKING LIGHT 8 87 8 87A 0 PARKING LIGHT OPTIONAL DRIVER DOOR PIN HORN AFTERMARKET HOOD SWITCH Automotive Data Solutions Inc. 7

MODULE PROGRAMMING PROCEDURE - STD KEY - OF Close driver door. 07 Turn key to position. ACC ON START 0 Re-open driver door to wake up data bus. 08 Remove key. ACC 0 ON START Insert key into ignition. 09 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. Turn key to ON position. 0 Wait, LED will turn solid GREEN for seconds. 0 LED will turn solid RED. Module Programming Procedure completed. 0 Within seconds, LED will ﬂash GREEN rapidly. ACC ON START 0 ACC ON PAGE OF DOC.: #89 707 START Automotive Data Solutions Inc. 7

VALET MODE PROGRAMMING PROCEDURE - OF >> NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. Time restriction. Complete next step within 7 seconds. 0 ACC ON START >> PAGE OF DOC.: #89 707 To exit valet mode: repeat steps to. Cycle ignition ON five times [x /ON] rapidly. ENGINE START STOP 0 0 Wait, LED will turn solid RED for seconds. Set ignition to position. ACC ON START ENGINE START STOP 0 Valet Mode Programming Procedure completed. Automotive Data Solutions Inc. 7

AFTERMARKET REMOTE PROGRAMMING PROCEDURE - OF >> WARNING: Program aftermarket remotes before usage. A maximum of four [x] aftermarket remotes per system. 0 LED will ﬂash GREEN once [x]. Time restriction. Complete next step within 7 seconds. 07 LED will turn solid RED. Cycle ignition ON five times [x /ON] rapidly. >> To program additional remotes: repeat steps to 7 using each additional remote. 0 LED will turn solid RED. 08 Wait, LED will turn. 0 Time restriction. Complete next step within seconds from previous step. 09 0 ACC ON START PAGE OF DOC.: #89 707 ENGINE START STOP Set ignition to position. ACC ON START ENGINE START STOP 0 Press once [x] on LOCK button of aftermarket remote. Automotive Data Solutions Inc. 7 0 Aftermarket Remote Programming Procedure completed.

PAGE 7 OF DOC.: #89 707 MODULE NAVIGATION PROCEDURE - OF >> It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP. 0 >> Module must be programmed to the vehicle. 0 >> Use the Module Navigation Chart on the next page. 0 Set ignition to position. 07 TO ACCESS THE MENUS: Press and hold programming button until LED turns solid GREEN. 08 IN THE MENUS: Press the programming button as many times as the menu number indicates. LED will ﬂash GREEN an equal amount of times continuously. 09 ACC ON START TO ACCESS THE OPTIONS: Press and hold programming button until LED turns solid RED. 0 IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED will ﬂash RED an equal amount of times continuously. TO ACCESS THE SETTINGS: Press and hold programming button until LED turns solid GREEN. Configure every other setting and proceed to step. [Z] LED will ﬂash GREEN as many times as the current (or default) setting number, continuously. MANDATORY: EXIT MODULE NAVIGATION. Press and hold programming button for 7 seconds. LED will ﬂash RED rapidly. Release programming button. LED will turn. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED will ﬂash GREEN an equal amount of times continuously. Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. >> Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIONS: Press and hold programming button until LED turns solid RED. [Y] LED will ﬂash RED as many times as the current option number continuously. ENGINE START STOP 0 0 [X] Automotive Data Solutions Inc. 7

PAGE 8 OF DOC.: #89 707 [Y] OPTIONS [X] MENUS MODULE NAVIGATION CHART: NOTES I Default settings are listed in bold. II Make sure the option is covered on the vehicle before attempting to change the setting. 0 0 0 DISARM/UNLOCK BEFORE START RELOCK AFTER START RELOCK AFTER SHUTDOWN FORCE UNLOCK ALL ON FIRST PRESS 0 TAKEOVER 0 07 [Z] SETTINGS MODULE NAVIGATION CHART - OF FACTORY KEYLESS RS SEQUENCE CONFIGURATION 08 09 MODULE RUN TIME WAIT TO START DELAY 0 ON 0 ON 0 ON 0 ON ENABLE 0 DISABLE* DISABLE 0 0 LOCK + UNLOCK + LOCK 0 LOCK + LOCK + LOCK 0 MIN 0 0 MIN 0 0 MIN 0 MIN 0 MIN 0 0 MIN 07 MIN 08 MIN 0 SEC 0 0 SEC 0 08 SEC 0 0 SEC 0 SEC 0 0 SEC 07 SEC 08 0 SEC 0 *Vehicle will shutdown when a door is opened. Automotive Data Solutions Inc. 7

PAGE 9 OF DOC.: #89 707 [Y] OPTIONS [X] MENUS MODULE NAVIGATION CHART: NOTES [Z] SETTINGS MODULE NAVIGATION CHART - OF HORN EVENT TRIGGER CONFIGURATION 0-07 Technical Support only HORN CHIRPS WIDTH DOUBLE LOCK 0 LOCK + UNLOCK 0 LOCK + UNLOCK + START 0 DOUBLE LOCK + START 0 msec 0 msec 0 0 msec *Vehicle will shutdown when a door is opened. Automotive Data Solutions Inc. 7

[X] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC REMOTE STARTER ERROR CODES - OF I WARNING: The following applies only when the parking lights are connected and supported by the system. Engine running. 0 Key in ignition at ON position. II After a remote starter failure, the parking lights will flash three [x] times, then will flash [X] number times to indicate an error code. See table. 0 0 Trunk is open. 0 Foot brake is ON. 0 Hood is open. 07 08 Tach failure. 09 0 System is in Valet Mode. CAN communication failure RS not synchronized. Start vehicle with OEM key for sec before trying a new RS sequence. [Y] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC REMOTE STARTER ERROR CODES: NOTES I WARNING: The following applies only when the parking lights are connected and supported by the system. Engine tach signal is lost. 0 II If the engine shuts down after a remote starter sequence: Press and hold the Trunk button and the Start button at the same time for. seconds when using a -WAY remote. OR Press once [x] on button when using a -WAY remote. 0 Foot brake is ON. 0 Hood is open. 0 Engine RPM limiter is ON. 0 Glow plug timeout error. 07 Vehicle is moving (VSS). 08 Check engine warning light is ON. 09 Low fuel warning light is ON. 0 CAN communication failure during RS sequence. REMOTE STARTER SHUTDOWN ERROR CODES: NOTES The parking lights will ﬂash four [x] times, then will ﬂash [Y] number times to indicate an error code. See table. Automotive Data Solutions Inc. 7 PAGE 0 OF DOC.: #89 707

I II III DURING PROGRAMMING DURING REMOTE START WITH IGNITION Automotive Data Solutions Inc. 7 DIAGNOSTIC TEST MODULE LED STATUS MODULE DIAGNOSTICS - OF Flashing RED Missing/wrong information from firmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN Additional steps required to complete module programming. Solid GREEN then Module correctly programmed. No activity or module already programmed. Flashing RED Module incorrectly programmed. Solid RED Module incorrectly programmed. Flashing GREEN Module correctly programmed and operational. Solid GREEN then Reset in progress. Invalid ground when running status from remote starter. Flashing RED Module incorrectly programmed or connected. Solid RED Module not programmed. Waiting for more vehicle information. Flashing GREEN False ground when running status from remote starter. Solid GREEN then Reset in progress. Module at rest and ready for a remote start sequence. PAGE OF DOC.: #89 707

MODULE RESET PROCEDURE - OF Disconnect all connectors from module except the BLACK 0-PIN connector. 07 Reconnect all connectors. 0 Disconnect the BLACK 0-PIN connector. 08 Repeat programming procedure. 0 PRESS AND HOLD the module s programming button while connecting the BLACK 0-PIN connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 0 Wait, LED will ﬂash RED. RELEASE programming button. 0 LED will turn RED for seconds. 0 Module RESET completed. Automotive Data Solutions Inc. 7 PAGE OF DOC.: #89 707

TAKEOVER PROCEDURE - STD KEY - OF >> All vehicle doors must be closed and locked prior to remote start sequence. Press unlock on OEM or aftermarket remote. 0 Insert key into ignition. ACC Failure to follow procedure will result in vehicle engine shutdown. ON START 0 >> PAGE OF DOC.: #89 707 Turn key to ON position. ACC ON START 0 Press and release BRAKE pedal. 0 Take over procedure completed. Automotive Data Solutions Inc. 7

INSTALLATION CHECKLIST - OF PAGE OF DOC.: #89 707 CHECKLIST WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. Press the LOCK button once [x] on the aftermarket keyfob. 9 Press the START/STOP button once [x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question : Do the doors lock? YES: Go to next step. NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. RAP and auto light shutdown test YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 0 Press the UNLOCK button once [x] on the aftermarket keyfob. YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Question : Do the doors unlock? Question 8: Did the radio, interior controls and headlights turn off within 0 seconds after remote start shutdown? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Press the START/STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question : Does the trunk or hatch open/unlock? Question 9: Does the vehicle remote start? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Press the AUX button once [x] on the aftermarket keyfob if supported. Enter vehicle and close the doors. Question : Does the driver side sliding door open? Press the START/STOP button once [x] on the aftermarket keyfob to remote start vehicle. YES: Press the AUX button once [x] to close the driver sliding door and go to next step. 7 Wait for the vehicle to start. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 8 Press brake pedal. 7 Press the AUX button once [x] on the aftermarket keyfob if supported. YES: Go to next step. YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. Close hood. Question 0: Does the vehicle shut down? Question : Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 8 Press the START/STOP button once [x] on the aftermarket keyfob to remote start vehicle. 0 Installation checklist completed. Question : Does the vehicle remote start? YES: Go to next step. NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists. Automotive Data Solutions Inc. 7