Chemical Hydraulic Valve Designed for hauling a variety of products U.S. Pat. No. 3,065,949 Patented 962 Schematic Tel. (84) 723-250 Fax (84) 723-7030 E-Mail: betts@bettsind.com Web Site: www.bettsind.com Nov 2005 Section 35 Page A
Chemical Hydraulic Valve Recommended Practice The Chemical Hydraulic Valves are designed to operate at approximately 3000 P.S.I. hydraulic working pressure. Valve should be mounted on a good flat surface. Valve and fittings should be protected as specified in 49 CFR 78.345-8a(2). Mount hydraulic pump and distributor in a convenient location for operation. Fusible plugs or fusible-frangible plugs for remote closing of valve should be located where specified in 49 CFR 78.345-(b)(). INSTALLATION SUGGESTIONS A. MOUNTING PAD: A flat mounting surface is important to prevent distortion of seat flange. We recommend the use of mounting pad No. MP9752LC or equal (see Section 40). B. HYDRAULIC FITTINGS: When installing tubing, be certain tube is free of grit, filings or chips. Care should be exercised to avoid sharp bends or kinks. Support long runs with clips or brackets. Expansion loops should be formed below the horizontal line formed by the tubing, to prevent trapping of air in lines. C. HYDRAULIC PUMP AND DISTRIBUTOR: We recommend the use of hydraulic pump No. HP46982SL as shown on page 3D. This pump is designed with a bypass to prevent damage to valve or hydraulic line due to expansion of hydraulic fluid from the product heat. If pump is used to operate more than one valve, use distributor No. CH6283 for individual valve control. Pump will handle up to five hydraulic valves. D. FUSIBLE-FRANGIBLE PLUGS: 49 CFR 78.345-(b)() requires a secondary closing mechanism to be located in an area remote from the tank opening and discharging points. Use fusible-frangible plug No. FP507BR, see Section 3, Page 3B. INSTRUCTIONS FOR FILLING HYDRAULIC SYSTEM Fill the pump reservoir if needed with a good grade of hydraulic fluid, ATF or a mixture of two parts antifreeze to one part water. A water/antifreeze mixture will help prevent freeze up for a pump that may be used in cold climates. Loosen fittings at valves and fusible-frangible plugs. Turn relief valve handle on pump clockwise and operate pump until all the air is bled. Tighten fittings and fusible-frangible plugs. Operate pump until bypass is reached. Check all connections for leaks. Release system pressure and refill pump reservoir to replace hydraulic fluid used to prime the system. Tel. (84) 723-250 Fax (84) 723-7030 E-Mail: betts@bettsind.com Web Site: www.bettsind.com Oct 2005 Section 35 Page B
Chemical Hydraulic Valve Replaceable Teflon Seat Removable-Replaceable Disc All Seals PTFE 2 Piece Replaceable Stem EXTERNAL VALVE C The Chemical Hydraulic Valve is designed for use with a wide variety of chemicals. A replaceable Teflon seat and removable disc are provided for ease in repairing should damage occur from dirt or other foreign material. A heavy mounting flange is provided to insure a flat gasketing surface. A ¼ NPT Hydraulic connection conveniently located at the base of the piston cylinder. Indicator pins, which move in relation to the piston, show the position of the disc at all times. B This valve does NOT contain a shear section. The cargo tank must protect the valve by providing suitable protection as specified in 49 CFR 78.345-8(2).,500 psi minimum hydraulic line pressure required to operate valve, but do not exceed 3,000 psi hydraulic line pressure. See section 35 Page 2D for parts list 4x3 Shown Size Assembly No. Material * Inlet Flange Outlet Dimensions B.C. Holes B.C. Holes A B C Wt. (lbs.) Temp. Range MAWP 4x3 4x4 CH46955SST CH46955LHT CH46949SST CH46949LHT 36 SS 36 SS w/ Hastelloy trim** 36 SS 36 SS w/ Hastelloy trim** 7.25 8-9 / 6 4 7 / 8 4 3 / 4 6 4 / 2 29 8-7 / 6 5 7 / 8 7 5 / 8 6 7 7 / 8 30.5-40 F to +400 F 50 * Material listing is for all wetted surfaces exposed to product during normal operation of valve. ** Hastelloy trimmed valve has a hastelloy C-22 overlay on the disc (3) in the area in contact with the seal (6). The hastelloy overlay reduces the potential of the disc pitting at the seal contact area. Suffix 07 indicates Teflon Seat w/ Double Tef-Sil O-Ring. NOTE: A flat mounting surface must be provided for valve seat flange. Recommended mounting pad is MP9752LC, see section 40. For hydraulic pump and distributor, see page 3B or 3C. Tel. (84) 723-250 Fax (84) 723-7030 E-Mail: betts@bettsind.com Web Site: www.bettsind.com Feb 2005 Section 35 Page 2C
PARTS LIST CHEMICAL HYDRAULIC VALVE No. Description Req. Material Part No. No. Description Req. Material Part No. Cap Nut 36 Stnls 6672SS 8 Follower Washer 36 Stnls 9594SS 2 Cap Collar 36 Stnls 667SS 9 Packing Rings set of 3 Teflon 5759TF 3 Disc 36 Stnls 6743SS 0 Spring - Stuffing Box 36 Stnls 966SS Hast. C-22 Trim 6743LH Washer - Main Spring 304 Stnls 5684SL 4 Teflon Washer Teflon 6690TF 2 Main Spring Chr. Van. 8850EY 5 Upper Stem Half 36 Stnls 28202SS 3 Lower Stem Half 303 Stnls 2820SL Hast. C276 28202HC 4 Piston 303 Stnls 7536SL Teflon 6644TF 5 Main Seal 302SS/PTFE 75207SSTF 6 Replaceable Seat Kalrez 6644KA 6 Seal Retainer Ring 303 Stnls 7590SL Replaceable Seat Teflon 8897TFTS 7 Piston O-Ring Seal Tef-Sil 75206TS 6a w/ O-rings Kalrez 8897KA 8 Piston Holder 36 Stnls 7537SS 6b Seat O-ring Only 2 Tef-Sil 8246TS 9 Indicator Pins 2 304 Stnls 633SL Kalrez 8246KA 20 Seal Washer Fiber 9Z685 7 Wiper Teflon 5862TF 2 Bearing Carbon PTFE 75455TF REPLACE DISC AND/OR SEAT: Hold cap collar (2) and remove cap nut () and remove disc (3). Care should be taken not to lose Teflon washer (4). Remove seat (6), use care not to damage seat surface of seat flange. Install new disc (3) and/or seat (6). REPLACE STUFFING BOX PACKING OR MAIN SEAL: Disconnect hydraulic line and unscrew indicator pins (9) and piston holder assembly (4) & (8). To ensure disc (6) does not get damaged, hold cap collar (2) stationary while using a spanner wrench (6236MS) to unscrew the seal retainer ring (6). REPLACE STUFFING BOX PACKING: If lower stem half (3) remains in valve body after seal retainer ring (6) has been removed, hold cap collar (2) and insert a ¼ thick x 2 wide piece of plate into the slots on the bottom of the lower stem half and unscrew it from the upper stem half. Remove main spring (2), washers (8) & () and stuffing box spring (0). Remove old packing (9) and wiper (7) and replace with new. For more detailed instructions, see maintenance manual MM-CH004. Tel. (84) 723-250 Fax (84) 723-7030 E-Mail: betts@bettsind.com Web Site: www.bettsind.com Replacement Kit of Teflon Parts: CH75296TF - Includes items 4,6,7,8,9,0,5,20 CH75296TFTS - Includes items 4,6a,6b,7,8,9,0,5,20 Conversion/Rebuild Kit: To Convert from Old Style Single Piece Stem to New Style 2 Piece Stem CH75297TF - Includes items 4,5,6,7,8,9,0,3,4,5,6,7,8,20 CH75297TFTS - Includes items 4,5,6a,6b,7,8,9,0,3,4,5,6,7,8,20 See maintenance manual MM-CH004 for complete rebuilding instructions WARNING: Use only genuine BETTS INDUSTRIES, INC. replacement parts. Use of substitute parts can impair the proper function of this product and void all warranties. REPLACE MAIN SEAL: If lower stem half (3) unscrews fro the upper stem half 95) it will be necessary to clamp the lower stem half (3) in a vice to unscrew seal retainer ring (6). After removing seal retainer ring (6), remove old main seal and install new. Care should be taken not to damage seal surface of lower stem half (3). Nov. 2008 Section 35 Page 2D
Chemical Hydraulic Valve STEAM JACKET VALVE Standard Valve With Steam Jacket Replaceable Teflon Seat Removable-Replaceable Disc All Seals PTFE 2 Piece Replaceable Stem The Steam Jacketed Chemical Hydraulic Valve is designed for use with a wide variety of chemicals. A replaceable Teflon seat and removable disc are provided for ease in repairing should damage occur from dirt or other foreign material. A heavy mounting flange is provided to insure a flat gasketing surface. The steam jacket is fitted with two ¾ NPT fittings. ¼ NPT Hydraulic connection conveniently located at the base of the piston cylinder. Indicator pins, which move in relation to the piston, show the position of the disc at all times. This valve does NOT contain a shear section. The cargo tank must protect the valve by providing suitable protection as specified in 49 CFR 78.345-8(2).,500 psi minimum hydraulic line pressure required to operate valve, but do not exceed 3,000 psi hydraulic line pressure. See section 35 Page 2D for parts list 4 X 3 SHOWN Size Assembly No. Material * Inlet Flange Outlet Dimensions B.C. Holes B.C. Holes A B C Wt. (lbs.) Temp. Range MAWP 4x3 4x4 CH46966SST CH46966LHT CH46960SST CH46960LHT 36 SS 36 SS w/ Hastelloy trim** 36 SS 36 SS w/ Hastelloy trim** 7.25 8-9 / 6 4 7 / 8 4 3 / 4 6 4 / 2 33 8-7 / 6 5 7 / 8 7 5 / 8 6 7 7 / 8 34.5-40 F to +400 F 50 * Material listing is for all wetted surfaces exposed to product during normal operation of valve. ** Hastelloy trimmed valves includes hastelloy C-276 upper stem half (5), hastelloy C-22 trimmed disc (3), & body trimmed w/ hastelloy C-22 in the area in contact w/ the seat (6). Suffix 07 indicates Teflon Seat w/ Double Tef-Sil O-Ring. NOTE: A flat mounting surface must be provided for valve seat flange. Recommended mounting pad is MP9752LC, see section 40. For hydraulic pump and distributor, see page 3B or 3C. Nov. 2004 Section 35 Page 2E INDUSTRIES, INC. WARREN, PA. Tel. (84) 723-250 Fax (84) 723-7030 E-Mail: betts@bettsind.com Web Site: www.bettsind.com
Chemical Hydraulic Valve The Internal Chemical Hydraulic Valve is designed for use with a wide variety of chemicals. It is an internal self-closing stop valve, therefore it does not require under carriage crash protection. Available elbows are supplied with shear sections to meet 49CFR 78.345-8(a)(4). A heavy mounting flange is provided to insure a flat surface for a positive seal. A replaceable Teflon seat and a replaceable stem are provided for ease in repairing a damaged valve. INTERNAL VALVE The / 8 NPT Hydraulic connection is located on the outside of the mounting flange.,500 psi minimum hydraulic line pressure is required to operate the valve, but do not exceed 4,000 psi hydraulic line pressure. See section 35 page 3D & 3E for Betts Hydraulic Pump. See section 35 Page 5D for parts list Description Assembly No. Material * CH47003SST 36 Stainless R CH47003LHT ** 8 3 6 " 7 4 " 8-9 6 " 50 Wt. 3# NOTE: A flat mounting surface must be provided for the valve. Recommended mounting pad with extended studs is MP974LC found in Section 40 Page A. * Material listing is for all wetted surfaces exposed to product during normal operation of valve. ** Hastelloy trimmed valve is an option that includes Hastelloy C-22 overlay on the disc (5) in the area in contact with the seal (5). The Hastelloy overlay reduces the potential of the disc pitting at the seat contact area. Suffix 07 indicates Teflon Seat w/ Double Tef-Sil O-Ring. Available s Size Description 4 x 3 4 x 3 4 x 4 4 x 4 Assembly No. Material Inlet Flange Outlet Flange CH2665SS 36 SS 9.4# 4 36 SS 8 6 3 " 7 4 " 8-6 9 5 5 " 8 " 4 8 7 2 " 4 3 CH2666SS 4 " " 8-6 7 " 3.7# CH6859SS 36 SS 6 5.8# CH6826SS 36 SS 8 32 " 8 32 " 8 " 5 7 8 " 3.7# Teflon Envelope Gasket G27229TF-MIL is recommended for use between valve and outlet elbow. See Section 40, Page 2A for dimensions. Wt. Tel. (84) 723-250 Fax (84) 723-7030 E-Mail: betts@bettsind.com Web Site: www.bettsind.com Dec 2005 Section 35 Page 5C
PARTS LIST INTERNAL CHEMICAL HYDRAULIC VALVE Replacement Kit of Teflon Parts CH75358TF Includes items 4,7,8,2,3,5,6,7,8,9,20,2,22 CH75358TFTS Includes items 4,7,8,2,3,5a,5b,6,7,8,9,20,2,22 Conversion Kit To convert CH45843SST to CH47003SST CH75393SSTF Includes items,2,4,6,7,8,0,,2,3,5,6,7,8,9,20,2,22 CH75393SSTS Includes items,2,4,6,7,8,0,,2,3,5a,5b,6,7,8,9,20,2,22 For valve conversion instructions, see maintenance manual MM-CH005. No. Description Req. Material Seat Flange 36 Stnls 2 Cover Plate 36 Stnls 3 Cap Screw - Cover Plate 2 36 Stnls 4 Gasket - Cover Plate Teflon 5 Disc 36 Stnls 6 Stem/Spring Retainer 7 Backup Shim-Spring 8 Shim-Spring 9 Main Spring 0 Piston Seal Retainer 2 Main Hydraulic Seal 3 O-ring - Stem 36 Stnls Teflon 304 Stnls 36 Stnls 303 Stnls 36 Stnls Tef-Sil Part No. 46937SS 7560SS 9Q3305 7295TF 75224SS 6867TF 6866SL 6890SS 756SL 7562SS 75206TS No. Description Req. Material Part No. 4 Packing Retainer 36 Stnls 9446SS 5 Replaceable Seat Teflon 6644TF Kalrez 6644KA 5a Teflon 5b 2 Tef-Sil 8246TS Kalrez 8246KA 6 Spring-Stuffing Box 36 Stnls 966SS 7 Follower Washer 36 Stnls 9594SS 8 Packing Rings Set Teflon 5759TF 9 Wiper - Suffing Box Teflon 5862TF 20 Gasket - Cover Plate Teflon 9720TF 2 O-ring - Stem Backup Viton 3926VT 22 Bearing Ring 75455TF INSTALLATION INSTRUCTIONS: Mount valve. (Sandwich valve between mounting pad and flange of elbow.) Connect hydraulic line to valve but leave fitting loose to bleed the system. Operate pump until all air is bled from system and tighten fitting. Open and close valve several times. Close valve and refill pump reservoir. Inspect all fittings for leaks. WARNING: Use only genuine BETTS IND, INC. replacement parts. Use of substitute parts can impair the proper function of this product and void all warranties. REBUILDING VALVE: (Betts recommends using parts kit CH75358TF when rebuilding valve). Remove 2 cap screws (3) and cover plate (2). Discard gaskets (4) and (20). Inspect piston (0), if the OD of the piston is scratched, worn, or damaged it should be replaced. Use spanner wrench 75325MS to remove seal retainer (). Remove hydraulic seal (2) and bearing ring (22). Use spanner wrench 75325MS to remove stem/spring retainer (6). This will decompress main spring (9). - Inspect stem/spring retainer (6); if stem is damaged or scratched it must be replaced. Lift disc (5) off seat flange () and remove all components remaining in disc (5). Replace seat (5), wiper (9), packing (8), spring-stuffing box (6), stem O-ring seal (3) and backup seal (2) with new parts. Reinstall packing retainer (4), main spring (9) and shims (6) and (7). Apply removable thread lock compound to threads of seat flange () (do not use too much, just enough to coat threads) and insert stem/spring retainer (6) through packing (8) and thread onto hub of seat flange (); tighten to 90 ft lbs. Insert new hydraulic seal (2) with lips facing inwards into stem/spring retainer (6). Install bearing ring (22) into recess of seal retainer (). Apply anti-seize compound to threads of seal retainer (), install and tighten to 30 ft lbs. Install new gaskets (4) and (20) and bolt cover plate assembly (2) using cap screws (3); tighten cap screws to 40 ft lbs. For more detailed instructions, see maintenance manual MM-CH005 Tel. (84) 723-250 Fax (84) 723-7030 E-Mail: betts@bettsind.com Web Site: www.bettsind.com Sept. 200 Section 35 Page 5D
Hot Products Valve EXTERNAL VALVE High Flow Rate Removable-Replaceable Disc 2 Piece Replaceable Stem The 6 Hot Products Hydraulic Valve is designed to provide high discharge rates for products such as heavy fuel oils. This enables a tank to be unloaded much faster than with conventional valves. A replaceable Buna disc is provided for ease in repairing should damage occur from dirt or other foreign material. A heavy mounting flange is provided to insure a flat gasketing surface. ¼ NPT Hydraulic connection conveniently located at the base of the piston cylinder. Indicator pins, which move in relation to the piston, show the position of the disc at all times. This valve does NOT contain a shear section. The cargo tank must protect the valve by providing suitable protection as specified in 49 CFR 78.345-8(2).,500 psi minimum hydraulic line pressure required to operate valve, but do not exceed 3,000 psi hydraulic line pressure. See section 35 Page 6D for parts list Size 6 6 Assembly No. CH4697MSB CH4697MST Material STEEL/ BUNA STEEL/ TEFLON Inlet Flange Outlet Dimensions B.C. Holes B.C. Holes A B C Wt. (lbs.) 9 / 4 2-9 / 6 8 / 8 2-9 / 6 7 6 3 / 8 6 / 2 55 9 / 4 2-9 / 6 8 / 8 2-9 / 6 7 6 3 / 8 6 / 2 55 Temp. Range -40 F to +275 F -40 F to +400 F MAWP 50 50 Nov. 2004 Section 35 Page 6C INDUSTRIES, INC. WARREN, PA. Tel. (84) 723-250 Fax (84) 723-7030 E-Mail: betts@bettsind.com Web Site: www.bettsind.com
PARTS LIST HOT PRODUCTS VALVE No. Description Req. Material Part No. No. Description Req. Material Part No. Cap Nut 36 Stnls 6672SS 2 Main Spring Chr. Van. 8850EY 2 Cap Collar 36 Stnls 667SS 3 Lower Stem Half 303 Stnls 2820SL 3 Disc Holder Steel 2683MS 4 Piston 303 Stnls 7536SL 4 Teflon Washer Teflon 6690TF 5 Main Seal 302SS/PTFE 75207SSTF 5 Upper Stem Half 6 Disc Tel. (84) 723-250 Fax (84) 723-7030 E-Mail: betts@bettsind.com Web Site: www.bettsind.com 36 Stnls 28202SS 6 Seal Retainer Ring 303 Stnls 7590SL Hast. C276 28202HC 7 Piston O-Ring Seal Tef-Sil 75206TS Buna 6886BN 8 Piston Holder 36 Stnls 7537SS Teflon 6886TF 9 Indicator Pins 2 304 Stnls 633SL 7 Wiper Teflon 5862TF 20 Disc Retainer Steel 6885MS 8 Follower Washer 36 Stnls 9594SS 2 Cap Screws 8 Steel 9Q5803 9 Packing Rings set of 3 Teflon 5759TF 22 Seal Washer Fiber 9Z685 0 Spring - Stuffing Box 36 Stnls 966SS 23 Bearing Carbon PTFE 75455TF Washer - Main Spring 304 Stnls 5684SL REPLACE DISC AND/OR SEAT: Hold cap collar (2) and remove cap nut (). Remove disc holder assembly (3). Care should be taken not to lose Teflon washer (4). Remove cap screws (2) and disc retainer (20) Replace disc (6) and reassemble. REPLACE STUFFING BOX PACKING OR MAIN SEAL: Disconnect hydraulic line and unscrew indicator pins (9) and piston holder assembly (4) & (8). To ensure disc (6) does not get damaged, hold cap collar (2) stationary while using a spanner wrench (6236MS) to unscrew the seal retainer ring (6). REPLACE STUFFING BOX PACKING: If lower stem half (3) remains in valve body after seal retainer ring (6) has been removed, hold cap collar (2) and insert a ¼ thick x 2 wide piece of plate into the slots on the bottom of the lower stem half and unscrew it from the upper stem half. Remove main spring (2), washers (8) & () and stuffing box spring (0). Remove old packing (9) and wiper (7) and replace with new. For more detailed instructions, see maintenance manual MM-CH004. WARNING: Use only genuine BETTS INDUSTRIES, INC. replacement parts. Use of substitute parts can impair the proper function of this product and void all warranties. REPLACE MAIN SEAL: If lower stem half (3) unscrews fro the upper stem half 95) it will be necessary to clamp the lower stem half (3) in a vice to unscrew seal retainer ring (6). After removing seal retainer ring (6), remove old main seal and install new. Care should be taken not to damage seal surface of lower stem half (3). Nov. 2008 Section 35 Page 6D
Quick Clean Chemical Hydraulic Valve QUICK CLEAN VALVE Quick Disassembly Shear Section Provided Hydraulics Isolated from Product Product Contact Seals PTFE The Quick Clean Chemical Hydraulic Valve meets the requirements of an internal self-closing stop valve. It is designed for use with a wide variety of chemicals. The Quick Clean features a readily removable spring housing assembly and a hydraulic actuator that can be replaced without removing the valve from the tank. The hydraulic system is completely isolated to eliminate possible product contamination. A resilient Teflon encapsulated o-ring with a tapered seat provides positive sealing. A heavy mounting flange is provided to insure a flat gasket surface. Valve includes a shear section which meets requirements of 49CFR78.345-8 and tested per TA RP 84. An indicator rod located at the base of the actuator moves in relation to the seat. ¼ NPT hydraulic port is located on the flange of the actuator.,500 psi [03 bar] minimum hydraulic line pressure required to operate valve, but do not exceed 3,000 psi [206 bar] hydraulic line pressure as provided by Betts pump HP46982. Note: 4x4 model shown. See section 35 Page 7B for parts list. Size Assembly No. Material * Inlet Flange Outlet Dimensions Wt. B.C. Holes B.C. Holes A B C (lbs.) 4x3 4x4 CH4686SSTS CH4686LHTS CH46874SSTS CH46874LHTS 36 SS 36 SS w/ Hastelloy trim** 36 SS 36 SS w/ Hastelloy trim** 7.25 [84 mm] 8 Holes.56 [4.2 mm] 4.88 [24 mm] 5.88 [49 mm] 8 Holes.44 [. mm] 4.75 [2 mm] 8.3 [206 mm] 2.05 [307 mm] 4.8 [376 mm] 4.50 [4 mm] 7.88 [200 mm] 26 [.8 kg] 29 [3. kg] * Material listing is for wetted surfaces exposed during normal operation of valve. ** Hastelloy trimmed valve is an option that includes Hastelloy C-22 overlay on the seat area in contact with the seat o-ring (5). The Hastelloy overlay reduces the potential of the seat pitting at the seal contact area. *** Values shown are test values. Actual values may vary due to service conditions. NOTE: A flat mounting surface must be provided. Recommended mounting pad is MP9752LC. For hydraulic pump and distributor, see section 35, page 3B and 3D. Temp. Range *** -40 F to +400 F [-40 C to +204 C] MAWP 50 psi [3.4 bar] Tel. (84) 723-250 Fax (84) 723-7030 E-Mail: betts@bettsind.com Web Site: www.bettsind.com March 2009 Section 35 Page 7A
PARTS LIST QUICK CLEAN CHEMICAL HYDRAULIC VALVE No. Description Req. Material Part No. Spring Housing 36 Stainless 28244SS 2 Spring 36 Stainless 943SS 3 Washer 36 Stainless 9083SS 4 Spring Washer 36 Stainless 75269SS 5 Retaining Ring 302 Stainless 9Q4923 6 Packing Spring 302 Stainless 9050SL 7 Spider 36 Stainless 2834SS 8 Spacer Sleeve Teflon/Glass 8467TG 9 Bushing Holder 36 Stainless 75268SS 0 Base O-Ring Tef. Encap. Sil. 75274TS Retaining Screw 4 36 Stainless 9Q5822A 2 Packing Set Teflon 8N2833 3 Wiper Teflon/Glass 872TG 4 Stem & O-ring Holder 36 Stainless 9254SS 5 Seat O-ring Tef. Encap. Sil. 9033TS 6 Retainer Plate 36 Stainless 27443SS 7 Cap Screw /2" 4 36 Stainless 9Q474 8 Body Assy - 4x4 35826SS 36 Stainless Body Assy - 4x3 35729SS 9A Barrel Cap U-Cup Seal TFM/Elgiloy 75494SLTF 9B Barrel Cap O-Ring Tef. Encap. Sil. 8858TS 20 Hex Nut /4-20NC 4 36 Stainless 9Q5805 2 Lockwasher /4" 4 36 Stainless 9Q5844 22 Cap Screw -/2" 4 36 Stainless 9Q499 23 Hyd. Actuator - 4x4 35224SSTS 36 Stainless Hyd. Actuator - 4x3 35233SSTS Spring Housing Assembly, 36054SSTS, includes items through 3. Seal Kit for Spring Housing Assembly, CH75549TF, includes items 8, 0, 2, & 3. Consult maintenance manual MM-CH00 for Spring Housing Assembly repairs. Consult maintenance manual MM-CH002 for Valve repairs. WARNING: Use only genuine BETTS INDUSTRIES, INC. replacement parts. Use of substitute parts can impair the proper function of this product and void all warranties. Tel. (84) 723-250 Fax (84) 723-7030 E-Mail: betts@bettsind.com Web Site: www.bettsind.com March 2009 Section 35 Page 7B