evel instruments Siemens AG 2009 Overview Configuration Horizontal mounting (recommended mounting position, particularly for adhesive applications) Vertical mounting with lower density is a compact vibrating level switch for use in liquid and slurry applications such as overflow, high, low and demand applications, as well as pump protection. It is ideal for use in confined spaces. Benefits Proven vibrating level switch technology for liquids Compact insertion length of (1.7") for confined space applications Fault monitoring for corrosion, loss of vibration, or line break to the piezo drive Integrated test function to confirm correct operation Application is a compact level switch designed for industrial use in all areas of process technology and can be used with liquids and slurries. With an insertion length of only (1.7 ), can be mounted in small pipes and confined space applications. It is virtually unaffected by the chemical and physical properties of the liquid. The V100 can be used in difficult conditions including turbulence, air bubbles, foam generation, buildup, or strong external vibration. The tuning fork is piezoelectrically energized and vibrates at a mechanical resonance frequency of approximately 1200 Hz. The vibration frequency changes when the tuning fork is covered by the medium. This change is detected by the integrated oscillator and converted into a switching command. The integrated electronics evaluate the level signal and output a switching signal to connected devices. Key Applications: For use in liquids and slurries, for level measurement, overfill, and dry run protection [approx. (0.1 )] with higher density Horizontal mounting in viscous or adhesive applications Moisture protection 30 mm (1.18 ) (0.1 ) (0.1 ) NOTE: Welded socket for flush mount optional Ensure cable gland faces downward to avoid water ingress. Installation /78 Siemens FI 01 2010
Siemens AG 2009 evel instruments Technical specifications Options Mode of operation Measuring principle Input Measured variable Output Vibrating point level switch High and low and demand V100 Threaded Welded Socket G¾" A / 316 32 mm (1.26 ) G ¾ G1A / 316 32 mm (1.26 ) G 1 Output options Measuring Accuracy - Contactless electronic switch - Transistor output PNP 32 mm (1.26 ) 29. mm (1.16 ) Hysteresis Switching delay Frequency approx. 2 mm (0.08") with vertical installation approx. 00 ms (on/off) approx. 1200 Hz 3 mm (2.09 ) 60 mm (2.36 ) Rated operating conditions Installation conditions Welded socket ocation Indoor/outdoor Ambient conditions Ambient temperature -40 to +70 C (-40 to +18 F) Installation category III Pollution degree 2 Medium conditions Temperature - Standard -40 to +100 C (-40 to +212 F) - High temperature option -40 to +10 C (-40 to +302 F) Pressure (vessel) -1 to 64 bar g (-14. to 928 psi g) Density 0.7 to 2. g/cm³ (0.02 to 0.09 lbs/in³) Design Material - Enclosure 316 and Plastic PEI - Tuning fork 316 (1.4404 or 1.443) - Process connection (threaded) 316 (1.4404 or 1.443) - Process seal Klingersil C-4400 Process connection - Pipe thread, cylindrical (ISO 228 T1) G ¾" A or G 1" A - Pipe thread, tapered ¾" NPT or 1" NPT - Hygienic fittings Bolting DN40 PN40 Tri-clamp 1", 1½", 2" PN 10 Degree of protection IP6/Type 4/NEMA 4 (with DIN 4360 valve plug), IP66/67 or IP68 (with M12 connector) Conduit entry 1 x M12 [IP66/IP67 or IP68 (0.2 bar)] Weight (housing) 20 g (9 oz) Power supply Supply voltage 20 to 23 V AC, 0/60 Hz 20 to 23 V DC Power consumption 1 to 8 VA (AC), approx. 1.3 W (DC) Certificates and approvals Overfill protection (WHG) Shipping approvals Siemens FI 01 2010 /79
evel instruments Siemens AG 2009 Selection and Ordering data Compact vibrating level switch for use in liquid and slurry applications such as overflow, high, low and 7 M 7 4-7 7 7 77-77 A 0 demand applications, as well as pump protection. Ideal for use in confined spaces. Approvals Without approvals 1 Shipping approvals 1) 2 Overfill protection (WHG) 2) 3 Process temperature Standard -40 to +100 C (-40 to +212 F) 3) A Extended -40 to +10 C (-40 to +302 F) 3) B Hygienic applications -40 to +10 C (-40 to +302 F) 4) C Process connection Thread G¾" A PN64/316 A 0 Thread G¾" A PN64/316 Ra<0.8µm A 1 Thread ¾" NPT PN64/316 A 2 Thread ¾" NPT PN64/316 Ra<0.8µm A 3 Thread G1" A PN64/316 A 4 Thread G1" A PN64/316 Ra<0.8µm A Thread 1" NPT PN64/316 A 6 Thread 1" NPT PN64/316 Ra<0.8µm A 7 Tri-Clamp 1" PN16 DIN 32676/316 Ra<0.8µm A 8 Tri-Clamp 1½" PN16 DIN 32676/316 Ra<0.8µm B 0 Tri-Clamp 2" PN16 DIN 32676/316 Ra<0.8µm B 1 Bolting DN2 PN40 DIN 1181/316 Ra<0.8µm B 2 Bolting DN40 PN40 DIN 1181/316 Ra<0.8µm B 3 Bolting DN0 PN2 DIN 1181/316 Ra<0.8µm B 4 SMS DN38 PN6 SMS114/316 Ra<0.8µm B Hygienic fitting with compression nut F40 B 6 PN2/316 Ra<0.8µm Electronics Contactless electronic switch 20 to 20 V AC/DC ) 1 Transistor output PNP 10 to V DC 2 Housing 316 1 Electrical connection/protection M12x1/IP67 A According to DIN 4360 including plug/ip6 B Acc. to DIN 4360 incl. plug with QuickOn connection/ip6 C M12x1 incl. m cable/ip68 (0.2 bar) D Further designs Order code Please add "-Z" to and specify Order code(s). Cleaning including Certificate W01 (oil, grease and silicone free) Identification abel, foil laser marking Y16 Acceptance test certificate 3.1 for instrument C12 Acceptance test certificate 2.2 for instrument C14 Selection and Ordering data Compact vibrating level switch for use in liquid and slurry applications such as overflow, high, low and demand applications, as well as pump protection. Ideal for use in confined spaces. Additional instruction manual V100 (Contactless electronic switch), English V100 (Contactless electronic switch), French V100 (Contactless electronic switch), Spanish V100 (Contactless electronic switch), German V100 (Transistor PNP), English V100 (Transistor PNP), French V100 (Transistor PNP), Spanish V100 (Transistor PNP), German This device is shipped with the Siemens Milltronics manual CD containing the complete instruction manual library. Spare Parts V100 Threaded Welded Socket G ¾" A / 316 with FKM Seal G 1 A / 316 with FKM Seal M27x1. / 316 with FKM Seal G ¾ A / 316 with EPDM Seal G 1 A / 316 with EPDM Seal M27x1. / 316 with EPDM Seal 7 M 7 4-7 7 7 77-77 A 0 7M1998-KN01 7M1998-KN11 7M1998-KN21 7M1998-KN31 7M1998-KP01 7M1998-KP11 7M1998-KP21 7M1998-KP31 7M1930-1EE 7M1930-1EF 7M1930-1EG 7M1930-1EH 7M1930-1EJ 7M1930-1EK 1) Available with Process Temperature option A only 2) Available with Electronics option 2 only 3) Available with process connection A0, A2, A4, and A6 only 4) Available with process connection A1, A3, A, and A7 to B6 only ) Available with Electrical connection/protection option B and C only /80 Siemens FI 01 2010
Siemens AG 2009 evel instruments Characteristic curves Ambient Temperature/Process Temperature derating curves Siemens FI 01 2010 /81
evel instruments Dimensional drawings Siemens AG 2009 (standard) 36 mm (1.42 ) 27 mm (1.06 ) (extended) Thread G ¾ A, G 1 A (DIN ISO 228/1), ¾ NPT or 1 NPT (valve plug DIN 4360) Tri-clamp (valve plug DIN 4360) 3 mm (1.38 ) 18 mm (6.22 ) ø 31.7 mm (1.2 ) 32 ~ 88 mm (3.46 ) ø 31.7 mm (1.2 ) ~ 101 mm (3.98 ) (1.7 ) G 1 A ø 21.3 mm (0.84 ) (0.1 ) = ength with G ¾ A, ¾ NPT: 66 mm (2.6 ) ength with G 1 A, 1 NPT: 69 mm (2.7 ) (1.7 ) (0.1 ) 32 G ¾ A, ¾ NPT G 1 A, 1 NPT ø 21.3 mm (0.84 ) = ength with G ¾ A, ¾ NPT: 66 mm (2.6 ) ength with G 1 A, 1 NPT: 69 mm (2.7 ) ength with Tri-clamp: 3 mm (2.1 ) switching point (standard with M12 connector) (extended, high temperature) Bolting DIN 1181 (valve plug DIN 4360) SMS 114 (valve plug DIN 4360) 10 mm (0.39 ) M12x1 ø 31.7 mm (1.2 ) 18 mm (6.22 ) 32 G ¾ A, ¾ NPT G 1 A, 1 NPT ~ 11 mm (4.3 ) ~ 10 mm (4.13 ) (1.7 ) ø 21.3 mm (0.84 ) (0.1 ) (1.7 ) (0.1 ) switching point = ength with G ¾ A, ¾ NPT: 66 mm (2.6 ) ength with G 1 A, 1 NPT: 69 mm (2.7 ) = ength with bolting: 3 mm (2.1 ) ength with SMS 114: 3 mm (2 ) dimensions /82 Siemens FI 01 2010
Siemens AG 2009 evel instruments Schematics connections Siemens FI 01 2010 /83