Your Partner for Micro and High Pressure Hydraulics For any alication where sace is limited and intelligent solutions are in demand, we are your cometent solution artner. From comonents to systems.
About Us BIERI Hydraulik BIERI Hydraulik AG, more than 60 years exerience and quality in Hydraulics and since 2011 art of the HYDAC Grou of comanies, is nowadays a leading international sulier of hydraulic and electrohydraulic solutions in the fi eld of micro and high ressure hydraulics. 500 bar 350 bar For any alication where sace is limited and intelligent solutions are in demand, we are your cometent solution artner. Our innovative solutions - from standard comonents to customer secifi c comonents and from sub-systems to comlete systems - essentially contribute to the succes of our customers. 200 bar 700 bar Through the HYDAC sales and service network, as well as through some selected indeendent distribution artners, we are always close to our customers and their alications. We cultivate a close artnershi with our customers and suliers, based on trust, rofi tability and sustainability. 1000 bar Hydac Grou HYDAC is your cometent artner for all rojects requiring fl uid technology in connection with hydraulics, electronics and engineering. HYDAC was founded in 1963 as a comany for hydraulic accessories and is today an internationally active comany grou with over 8000 emloyees, 50 branch offi ces and 500 trade and service artners world-wide. HYDAC comonents can be found in all areas of industrial and mobile hydraulics HYDAC solutions are based on Cometence for systems Flair for innovation Feeling for fl uids. 2/12 Solutions Systems Comonents Engineering Suort Simulation technologies Project engineering / Fluid engineering Modules / Manifolds / Accumulator stations Filtration.cooling-systems / Power acks Lubrication systems / Cylinder units Fluid filters / Process filters/ Hydraulic - accumulators / Sensors / Valves / Coolers Heat- exchangers / Pums / Ball valves / Fittings
Our Products 5 Best in Class Product Lines Your Benefits Features and Adventages of our Solutions Comact design, high ower density, robustness, durability and functionality are among the undisuted strengths of hydraulics. BIERI Hydraulik - as a leading international solution rovider in the fi eld of micro and high ressure hydraulics - sets the benchmark for these generally acceted advantages of hydraulics even higher. Our solutions are created to hel you - our customers - design your equiment in a sace-otimized, energy-effi cient way and with increased functionality. All this of course based on roven Swiss reliability. Sace - Otimization Our Solutions stand for: Multi - Functionality Energy - Effi ciency Reliability - Sustainability Please let yourself be convinced. Form Comonents to Systems 3/12
Our Customer Aroach From the otential benefit of our roducts to the erfect solution for you You our customers are in the focus of everything what we are doing. Our goal is to rovide you with the most suitable roduct and to assist you in the designing or redesigning of your hydraulic equiment, which can give you a cometitive advantage. Our international network and artnershi aroach, our innovative strength, fl exibility and reliability, can hel you to reduce unnecessary interfaces and benefi t from erfectly functioning solutions. When and wherever you need us, from the standard comonent to customer-secifi c comonents and from subsystems to comlete systems in the area of micro and high ressure hydraulics. customer & market-oriented innovative & fl exible organized & reliable Through close ersonal contact with you, we are insired by your individual ideas and wishes to fi nd and develo effi cient solutions. In this way, we maintain close artnershis on all hierarchical levels and throughout the entire rocess: from alication advice to roduct defi nition and even to the logistic and after-sales concet. With great imlementation skills and assion for detail, we will contribute to make your equiment more cometitive and with quicker availability. That is what drives us and is the key to our mutual success. As a artner with solution-fi nding skills, we understand the challenges of your markets and we have the skills to meet your secifi c requirements. Therefore, the search for a solution begins with the fi rst joint discussions. We critically question existing solutions, discuss innovative aroaches and decide together the best individual solution for you. Our comany structure allows a fl exible adatation to your own needs. Our alication and roduct know-how Your cometitive advantage. Our internal organization from order rocessing, roduction, assembly and logistics is designed to meet your requirements. Again, our maxim is: the right roduct at the right time, in the right lace, in the correct quantity and through the quality of internal rocesses and delivery to you. Our reliability a guarantee of our artnershi. BIERI Hydraulik - Your artner for individual solutions 4/12
Market Segments and Alications Powerfull equiment in demanding alications We have collected and imlemented know-how in a targeted manner for more than 60 years. That is why we know very well how different the secifi c requirements for different markets, industries and alications can be. And we are aware of how quickly a technological advantage is gained or even overtaken, if one does not always strive to develo oneself further. For that reason and for key alications, we have within Bieri Hydraulik and the Hydac Grou exerienced secialists, who are globally active and are fully focused on the requirements and trends of the industry. Otimal advanced technical solutions, targeted for these industries, are the result. With our industry-secifi c solutions and our alication knowledge, we can effi ciently suort you on the way to market success as your artner with thorough alication knowledge in micro and high ressure hydraulics. We are active in the following industries: BIERI Hydraulik - Your solutions artner with alication Know-How 5/12
Micro and High Pressure Comonents Best in Class Pums: Micro; 500; 700; 1000 bar Micro-Axial iston ums AKP Valve controlled on ressure and suction side. High volumetric effi ciency with a wide seed range. Small mounting dimensions and low noise. 3 and 5 istons. 250 bar, 350 bar, 500 bar, 800 bar Vg / n 0,012 2.292 cm3/r; 100 5000 min-1 Radial iston ums BRK Self riming, self venting. Valve controlled. High volumetric effi ciency. 3, 5, 7 and 9 uming elements. P 500 bar, 700 bar, 1000 bar Vg / n 0,24 8,14 cm3/r; 500 2000 min-1 Radial iston ums SRK-ATEX For use in exlosive environments also mounted outside of the hydraulic tank. Class II: gases, vaours, mists. P 700 bar Vg / n 0,47 6,33 cm3/r; 500 1800 min-1 Radial iston ums SRK Self riming, self venting, valve controlled. Suitable for oeration with oor lubricating mediums. 3, 5, 7 and 9 low friction uming elements with low sliding seed. P 700 bar Vg / n 0,47 6,33 cm3/r; 500 1800 min-1 Multi outlet ums MRK Various outlets available on request. Self-riming, self-venting. Valve controlled. High volumetric effi ciency. Number of outlets 2 to 9. P 700 bar Vg/Circuit / n 0,16 3,620cm3/r; 500 2000 min-1 Radial iston ums HRK Comact design. Direct installation of motor, no couling, no bell-housing. Version with hollow shaft, with or without ressure relief valve. 1 and 2 uming elements. P 700 bar Vg / n 0,12 4,52 cm3/r; 500 3600 min-1 Combination ums KKP Comact and lightweight. Integrated low-ressure shut-off valve and ressure rotection valve. Self-venting. Design with hollow shaft. 2, 3 and 4 uming elements. Vg / n LP 160 bar, HP 700 bar LP 0,35 5,43;HP 0,12 2,71 cm3/r 500 3600 min-1 (KKP01/02); 500 2000 min-1 (KKP03/04/05) Combination ums SKP Hollow shaft. Otionally integrated low-ressure shut-off valve. Self-venting. 2 or 3 uming elements HP stage. LP 100 bar, HP 700 bar Vg / n LP 4,45-16,71; HP 0,45-2,71 cm3/r 500 2000 min-1 Combination ums BKP Combination of BRK um and gear um. Outstanding energy effi ciency ratio. Fixed dislacement, any installation osition ossible. LP 250 bar, HP 1000 bar Vg / n LP 4,0 61,1 ; HP 0,47 8,14 cm3/r 500 2000 min-1 6/12
High Pressure Comonents Best in Class Valves 500 bar 500 bar Seated valves WVM-6I Direct oerated and leackage free. With hardened closing elements as cone seat. 2/2, 3/2, 3/3, 4/2, 4/3 or 4/4 functions with ositive or negative overla. Solenoids with slide on coil technology (turnable). Good corrosion resistance. / size 500 bar / NG 6 Q 25 L/min Seated valves WVM Direct oerated and leackage free. With hardened closing elements as cone or ball seat. 2/2, 3/2, 3/3, 4/2 functions with negative or ositive overla. Solenoids with slide on coil technology (turnable) or alternative actuation. Good corrosion resistance. / size 500 bar / NG 4 Q 12 L/min Seated valves ATEX WVMX Direct oerated and leackage free. With hardened closing elements as cone or ball seat. 2/2, 3/2, 4/2 functions. Solenoids with slide on coil technology ( turnable in 90 stes. For use in exlosive environments Class II: gases, vaours, mists. / size 500 bar / NG 4 Q 12 L/min Flow control valves SDM and SDRVM Adjustable while under ressure with high-recision control. The setting can be locked by a counter nut. Throttle valve as cartridge or in manifolds as throttle or throttle check valve. 500 bar Q 25 L/min Shut-off valves 500 bar / NG4 Leackage free in closed osition. Available as catridge or in modular and stand alone manifolds. 500 bar Manual shut-off valve AVM Q 25 L/min Check valve RVM 45 L/min Pilot oerated check valve ERVM Q 25 L/min P. o. CV with decomression ERVPM Q 63 L/min / NG 10 Pressure valves 500 bar / NG4 Direct oerated oet valve as cartridge or with modular- or stand alone manifolds. Outstanding stability over the entire fl ow range. Low hysteresis and exact ressure control and adjustment. / size 500 bar / NG 4 Pressure relief valve DVM Q 30 L/min Pressure reducing valve DMM Q 30 L/min Unloading valve DAM Q 40 L/min 7/12
High Pressure Comonents Best in Class Valves 700 bar 700 bar Seated valves WVH Direct oerated and leackage free. With hardened closing elements as cone or ball seat. 2/2, 3/2, 3/3, 4/2 functions with negative or ositive overla. Solenoids with slide on coil technology (turnable) or alternative actuation. Good resistance against corrosion. / size 700 bar / NG 4 Q 12 L/min Seated valves ATEX WVHX Direct oerated and leackage free. With hardened closing elements as cone or ball seat. 2/2, 3/2, 3/3, 4/2 functions. Solenoids with slide on coil technology (turnable in 90 stes). For use in exlosive environments Class II: gases, vaours, mists. / size 700 bar / NG 4 Q 12 L/min Seated valves WVM-4B-Bi Direct oerated, leackage free and suitable for bidirectional fl ow, with hardened closing elements as cone seat. 2/2 and 3/2 functions with low ressure dro (Δ). Solenoids with slide on coil technology (turnable) or alternative actuation. Good corrosion resistance. / size 700 bar / NG 4 Q 12 L/min Seated valves WV-700 Direct oerated and leackage free. High duty cycle and long lifetime through hardened oets and valve seats. 2/2, 3/2, 3/3, 4/2, 4/3 functions with ositive overla (excetions see data sheet) and use of 1 to 4 valve cartridges. Solenoid or alternative actuation. / size 700 bar / NG 6 Q 25 L/min Manual sool valves HSV700 Minimum weight. Excellent rice-erformance ratio. / size 700 bar / NG 6 Q 25 L/min Flow control valves SD700 und SDR700 Adjustable while under ressure with high-recision control. The setting can be locked by a counter nut. Throttle valve as cartridge or in manifolds as throttle or throttle check valve. P / size 700 bar / NG 6 Q 25 L/min Pressure valves 700 bar / NG6 Direct oerated oet valve as Ceto 3 fl angeable sandwich late. Outstanding stability over the entire fl ow range. Low hysteresis and exact ressure control and adjustment. Pressure relief valve DV700 Q 25 L/min Pressure reducing valve DM700 Q 25 L/min Unloading valve DA700 Q 25 L/min Proortional ressure relief valves PDV700 Available as direct and ilot oerated version. High degree of ressure stability and linear curve. Force controlled roortional solenoid of robust design. P / size 700 bar / NG 6 Q direct oerated 2 L/min; Q ilot oerated 25 L/min 8/12 Shut-off valves 700 bar / NG6 Leackage free in closed osition. Available as catridge alone or in sandwich lates or manifolds. Manual shut-off valve AV700 Q 25 L/min Check valve RVH Q 45 L/min Pilot oerated check valve ERV700 Q 25 L/min
High Pressure Comonents Pums, Valves, Pressure Switches 1000 bar 1000 bar Radial iston ums BRK11/12 Self riming, self venting. Valve controlled. High volumetric effi ciency. 3, 5 and 7 istons 1000 bar Vg 0,47 4,4 cm3/rev. n 500 bis 2000 min-1 Manual shut-off valve SPV2 Poet design leakage free. Low oerating force. Both connections designed for max. ressure. For in-line mounting systems. 1000 bar Q 20 res. 32 L/min Pressure relief valve DV2 Cone seat valve direct oerated. Max. ressure adjustable by locking nut. Pressure relief valves with threaded connection for in-line mountig systems, mainly test benches. 1000 bar Q 3 12 L/min Pressure switches DV7.1 Piston tye ressure switch with one change-over switch, easily adjustable over the entire ressure range, with scale for re-setting of the ressure switching oint. 7 ressure ranges for the otimal adatation to any oerating ressure. P 1000 bar Pressure switches DV7.2 Combined instruments for ermanent ressure indication, available with two change-over switches, indeendently adjustable over the entire ressure range and which indicate the ressure settings. 7 ressure ranges for the otimal adatation to any oerating ressure. 1000 bar Oil level switches FS With any length u to 1200mm available, our oil level switches can be threaded directly into tank cover. Level and temerature control in the tank. Guaranteed otential free switching. Can be dismounted without removing the tank ca. Suitable with many different fl uids. 9/12
Customized Comonents Successful artnershi for your technological advantage Standard Comonents Pums Micro Axial iston ums Radial iston ums Valves Directional seat valves Pressure valves Flow control valves Shut-off valves Micro-Cylinders Customized comonents Based on our ortfolio of standard comonents and our alication- secifi c exertise, we have the willingness and ability to develo customized comonents, in cooeration with you. Perfect customized solutions as a result of close cooeration. Concet Develoment Prototye Testing Production Modernization Together we defi ne the design, and we assist you in your develoment work. This allows you to tread innovative aths, test rototyes or integrate the solution erfectly into your equiment. Once the solution has been develoed, we turn to the zero series, volume roduction and the maintenance service of our comonents over the entire life of your equiment. A technological advantage therefore becomes a successful artnershi Examle: Micro - Axial Piston Pum AKP Alication: Downhole directional drilling in the oil and gas industry Down hole directional drilling tools are used in oil & gas industry to drill for oil. They are used to control the direction of the drilling head in order to change direction from vertical to horizontal and to byass obstacles in the ground. These drilling tools as well as the secial tools LWD - Logging While Drilling, MWD - Measurement While Drilling, Wireline Tools, Comletion Tools and Well Tractors are used in the underground. Challenge: The osition and direction of the drilling tools are directed and controlled from the drilling latform. The drilling tools are driven u to 3 km deth and additionally, u to 9 km horizontally. They must be very small and are exosed to extreme oerating conditions. The ambient temerature can reach u to 175 C, the ambient ressure u to 2000 bar and all the while being subjected to extreme vibrations and shock stress. Solution: AKP Micro-Pums from BIERI, which are comonents of the directional control unit, ensure that the drilling tool reaches the target destination exactly and reliably. The drilling direction is defi ned by three fl as in the tool, which are actuated by a lunger cylinder. Driven by a DC servo motor, our ums ensure that reliable and accurate ressure is alied to the lunger cylinders. AKP Technical data: Suction volume: Vg = 0,012 cm3/r 2,2 cm3/r Revolutions: n = 50 min-1 5 000 min-1 O. ressure: = 120 850 bar Env. ressure: 2000 bar Housing: Ø21,5 x 66 Ø62,2 x 146 mm Shaft: Ø5 Ø13 with wedge, SW, I-6kt.,slot. 10/12
Systems and Sub-systems Your reliable artner for system solutions ONE sulier. ONE contact. ONE resonsible. Based on our many years of exerience in the fi eld of micro and high-ressure hydraulic systems and as a result of our innovation and engineering exertise, we are offering our Best in Class roducts with the M. SYSTEM in a comrehensive modular system. This hels us to fi nd the best individual solution also for your comlex requirements: The individual comonents comlement each other to form customized solutions. Unifi ed assemblies and the ossibility to combine them individually serve to increase effi ciency at an ideal rice-erformance ratio. Together with you, we can integrate our comonents and assemblies into Best in Class systems, which will make your equiment more cometitive and with faster availability. Examle: HP 700 bar Assemblies & Power Units 11/12
Industries and Alications Oil & Gas Downhole Directional Drilling Wellhead Control Panels (WHCP) Maritime Alications Oceanografi c Research ROV`s Process Control Medical Technology Surgical Tables Scanner Tables Rescue Beds / Stetchers Fun Park Safety Systems Hydraulics Restraint Systems Secial Vehicles Arrmored Vehiclles - Window Lifting Seat Adjustment Aerosace Locking Systems Hydraulic Tools Torque Wrencher Nut Slitter Bolt Slitter Concrete Slitter Concrete Crusher Foundry Equiment Fire & Rescue Equiment Cutters Forces/Pinchers Sreaders Claming Technology & Jig Construction Claming / Tensioning Systems Machine Tools auxiliary functions Milling & Machining Centers Grinding Machines Turning Lathes Sawing Machines Machine Tools Forming- Claming & auxiliary functions Mechanical & Servo Presses Hydraulic Presses Bending Machines Punches Small Presses - Forming Filter Presses Criming Tools Staming Presses Punching and Rivet Presses Bench & Worksho Presses Material Testing Presses High-Viscosity Lubrication (Grease) Lubrication Units Railway Lubrication Testing Systems Hydraulic Test Benches Material Testing Systems Energy & Power Generation High Voltage Circuit Breaker Wind Turbines Solar (Positioning) Construction Engineering Climbing Systems Tunnel- /Pieline Drilling Concrete Post Tensioning Pile Foundation Drilling Technology Vibration Damaning Bridge Construction Earthquake Devices Recycling Scra Cutting & Shredding Lifting & Transort Systems Rail Track Tools Wheel Set Presses Portable Machine Lifting Systems Construction Lifting Systems Shibuilding Lifting & Synchronised Lifting & Fixing Instalation of Engines and Screws MICRO & HIGH PRESSURE Hydraulic Solutions Global Presence. Local Exertise. BIERI Hydraulik AG For any alication where sace is limited and intelligent solutions are in demand, we will suort you on your way to market success as your solution artner for MICRO & HIGH PRESSURE hydraulics. And this everywhere in the world, close to you and your alications. BIERI Headquarters HYDAC Headquarters HYDAC Comanies BIERI Sales & Service artners Könizstrasse 274 CH-3097 Liebefeld Switzerland Tel. +41 3197009-09 Fax +41 319700910 info@bierihydraulics.com www.bierihydraulics.com www.hydac.com