install guide Document number 8 Revision Date 008 firmware OEM-CH(RS)-CH-[FLRSCH] hardware FLRSCH accessories FLPROG (REQUIRED) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. BEFORE INSTALLATI - Connect module to computer - Login to Weblink account - Flash firmware to module (module is not preloaded with firmware) - Use accessories accordingly (accessories are sold separately)
Page of DOC.: #8 008 VEHICLE LIST - OF FEATURES MODEL YEAR DATA IMMOBILIZER BYPASS X LOCK REMOTE PRIORITY UNLOCK DOOR LOCK DOOR UNLOCK ARM OEM ALARM DISARM OEM ALARM TRUNK/HATCH RELEASE DATA/MUX ER CTRL DOOR STATUS BRAKE PEDAL STATUS TACHOMETER STATUS PARKING LIGHT CTRL* RAP SHUTDOWN CTRL WARNING 00 AT - 00 / 00C AT 0- or Aspen AT -0 PT Cruiser AT 0-0 or CHRYSLER INSTALL TYPE MAKE I Install Type requires a T-harness manufactured before //0 Install Type requires a T-harness manufactured after //0-0 08- Caliber (with start wire) AT Caliber AT - Charger AT 0- or Durango AT -0 Magnum AT 0- or Nitro AT - Ram 00 AT -08 Ram 00 AT -09 Ram 00 AT -09 Ram 00 chassis cab AT -09 Ram 00 chassis cab AT 08-0 Ram 00 chassis cab AT 08-0 Commander AT 0- or Compass AT - Grand Cherokee AT 0- or Liberty AT 08- Patriot AT - Wrangler AT - 00 chassis cab AT 0 00 chassis cab AT * May require additional parts. 0 RAM JEEP DODGE Sebring AT Avenger AT Automotive Data Solutions Inc. or
Page of DOC.: #8 008 BOX CTENTS - OF BOX CTENTS MODULE LED BLUE BLACK BLACK 0 PIN CNECTOR T-HARNESS 8 0 8 0 7 9 7 9 8 0 7 9 PROGRAMMING BUTT LED A G F B E BLACK RF PORT/ WEBLINK PORT BLUE TELEMATIC PORT BLACK 7 9 WHITE MS VS PIN CNECTOR VS MS AFTERMARKET HOOD SWITCH AND CABLE C D 8 0 WARNING STICKER WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE WEBLINK PORT COMPUTER USB PORT PIN BLACK CABLE Automotive Data Solutions Inc.
Page of DOC.: #8 008 COMPENT LOCATOR Pink/DkGreen White/ Pink/LtBlue White/ Brown/Tan Pink/DkGreen Parking Light* White/ /Blue Pink/DkGreen White/ Pink/DkGreen White/ Pink/Orange 8 Parking light relay, engine compartment. Pink/Orange White/ /Blue 0- Parking Light* 0- Parking Light* 0- Parking Light* 0- Parking Light* CNECTOR NAME MODULE LOCATI WIRE DESCRIPTI POLARITY Grand Cherokee 0-0 Parking Light* JEEP Commander WIRE COLOR Magnum POSITI Charger CNECTOR TYPE DODGE Caliber (with start wire) CNECTOR COLOR PT Cruiser 0- Parking Light* CHRYSLER 00/00C YEAR MODEL MAKE TYPE - WIRE CHART - OF * Requires additional parts. Automotive Data Solutions Inc.
Page of DOC.: #8 008 TYPE - WIRING DIAGRAM - OF MODULE VEHICLE IGNITI SWITCH A G RF PORT/WEBLINK PORT B F TELEMATIC PORT E C D A VS SKIM CNECTOR NOTE REMOVE THE WHITE/GREEN WIRE FROM THE BLUE CNECTOR AND RE-INSERT IT IN PIN (AS SHOWN) (SEE DETAILED INSTRUCTIS THE NEXT PAGE) A CUT AND INSULATE THE WHITE/YELLOW WIRE (NEXT TO WHITE/GRAY WIRE) WARNING THIS WIRING DIAGRAM IS APPLICABLE LY IF THE REVISI DATE OF THE T-HARSNESS IS BEFORE: //0 A VS SKIM HARNESS MS 0 WHITE/RED 0 WHITE/GREEN B B NOTE 8 0 8 0 7 9 7 9 PURPLE - ER OUTPUT WHITE/YELLOW - CTROL OUTPUT ER - 0 CTROL - 0 CNECT THE WHITE/GREEN WIRE TO THE PINK WIRE AND CNECT THE WHITE/RED WIRE TO THE RED WIRE (SEE DETAILED INSTRUCTIS THE NEXT PAGE) A MS B WHITE/GREEN WHITE/RED WHITE/BROWN (NC) INSULATE WIRE 0 PINK 0 RED C 8 7 0 9 BROWN/BLACK - PARKING LIGHT OUTPUT 0 GRAY - RAP SHUTDOWN OUTPUT VEHICLE PARKING LIGHT CNECTI GRAY/GREEN - HORN OUTPUT CNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT 0 AMPS D V OR 8 0 7 9 0 GRAY/WHITE - HOOD STATUS INPUT CNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT WITHOUT OEM HOOD SWITCH: INSTALL AND CNECT TO AFTERMARKET HOOD SWITCH PARKING LIGHT 8 87 8 87A 0 PARKING LIGHT OPTIAL DRIVER DOOR PIN HORN AFTERMARKET HOOD SWITCH Automotive Data Solutions Inc.
TYPE - WIRING DIAGRAM - OF NOTE Page of DOC.: #8 008 NOTE STEP : -REMOVE THE WHITE/GREEN WIRE FROM THE BLUE CNECTOR CAREFULLY. -USE A UTILITY KNIFE TO PUSH GENTLY AGAINST THE LOCKING TAB. -DO NOT DAMAGE THE LOCKING TAB IN THE PROCESS. STEP : -IDENTIFY THE PINK (PIN 7) AND RED (PIN 9) WIRES FROM THE 0 PIN BLACK CNECTOR OF THE T HARNESS. -CAREFULLY STRIP THE PINK AND RED WIRES USING A WIRE STRIPPER. -DO NOT CUT THE WIRES IN THE PROCESS. WHITE/RED WHITE/GREEN STEP : -USING A UTILITY KNIFE, LIFT THE LOCKING TAB CAREFULLY FOR IT TO BE RE-USED. STEP : -CNECT AND SOLDER THE WHITE/RED WIRE TO THE RED WIRE. -CNECT AND SOLDER THE WHITE/GREEN WIRE TO THE PINK WIRE. WARNING FAILURE TO PROPERLY SOLDER CAN RESULT IN FAULTY CNECTIS AND PRODUCT MALFUNCTI STEP : -INSULATE THE CNECTIS WITH ELECTRICAL TAPE. STEP : -INSERT THE WIRE IN PIN OF THE CNECTOR, RIGHT NEXT TO WHERE IT USED TO BE. WHITE/RED WHITE/GREEN Automotive Data Solutions Inc.
Page 7 of DOC.: #8 008 COMPENT LOCATOR - Parking Light* White/ Pink/Red Violet Driver door module /Blue -0 Parking Light* White/ 08- Parking Light* White/ - Parking Light* White/ /Blue -0 Parking Light Nitro CNECTOR NAME MODULE LOCATI WIRE DESCRIPTI Durango DODGE POLARITY Caliber WIRE COLOR DODGE Avenger POSITI Sebring CNECTOR TYPE Aspen CNECTOR COLOR CHRYSLER 00 YEAR MODEL MAKE TYPE - WIRE CHART - OF Pink/Red Violet Driver door module - Parking Light* White/ + White/Green -0 Parking Light * Requires additional parts. Automotive Data Solutions Inc.
Page 8 of DOC.: #8 008 WIRE COLOR POLARITY MODULE LOCATI COMPENT LOCATOR White/Green White/Green White/Green White/Green - Parking Light* White/ /Blue /Blue 08- Parking Light* White/ -09 Parking Light -09 Parking Light -09 Parking Light 08-0 Parking Light 08-0 Parking Light JEEP Compass POSITI Ram 00 CNECTOR TYPE Ram 00 CNECTOR COLOR Ram 00 CNECTOR NAME DODGE Ram 00 WIRE DESCRIPTI Ram 00 YEAR MODEL MAKE TYPE - WIRE CHART - OF Liberty * Requires additional parts. Automotive Data Solutions Inc.
Page 9 of DOC.: #8 008 CNECTOR TYPE POSITI WIRE COLOR POLARITY MODULE LOCATI COMPENT LOCATOR - Parking Light* White/ /Blue - Parking Light* White/ + White/Orange Passenger kick pad Parking Light White/Green Parking Light White/Green 0 RAM 00 00 0 CNECTOR NAME CNECTOR COLOR Wrangler WIRE DESCRIPTI JEEP Patriot YEAR MODEL MAKE TYPE - WIRE CHART - OF * Requires additional parts. Automotive Data Solutions Inc.
Page 0 of DOC.: #8 008 TYPE - WIRING DIAGRAM - OF MODULE VEHICLE IGNITI SWITCH A G RF PORT/WEBLINK PORT B F TELEMATIC PORT A VS SKIM CNECTOR E C D A VS SKIM HARNESS A 8 0 8 0 7 9 7 9 MS A B MS PURPLE (NC) WHITE/YELLOW (NC) VEHICLE PARKING LIGHT CNECTI CNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT WHITE/BROWN - PARKING LIGHT OUTPUT PARKING LIGHT OR CNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT C 8 7 0 9 0 AMPS V OR BROWN/BLACK - PARKING LIGHT OUTPUT 0 GRAY - RAP SHUTDOWN OUTPUT CNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT GRAY/GREEN - HORN OUTPUT PARKING LIGHT 8 87 8 87A 0 PARKING LIGHT D 8 0 7 9 OPTIAL 0 GRAY/WHITE - HOOD STATUS INPUT DRIVER DOOR PIN HORN WITHOUT OEM HOOD SWITCH: INSTALL AND CNECT TO AFTERMARKET HOOD SWITCH AFTERMARKET HOOD SWITCH Automotive Data Solutions Inc.
Page of DOC.: #8 008 COMPENT LOCATOR Pink/DkGreen White/ Pink/LtBlue White/ Brown/Tan Pink/DkGreen Parking Light* White/ /Blue Pink/DkGreen White/ Pink/DkGreen White/ Pink/Orange 8 Parking light relay, engine compartment. Pink/Orange White/ /Blue 0- Parking Light* 0- Parking Light* 0- Parking Light* 0- Parking Light* CNECTOR NAME MODULE LOCATI WIRE DESCRIPTI POLARITY Grand Cherokee 0-0 Parking Light* JEEP Commander WIRE COLOR Magnum POSITI Charger CNECTOR TYPE DODGE Caliber (with start wire) CNECTOR COLOR PT Cruiser 0- Parking Light* CHRYSLER 00/00C YEAR MODEL MAKE TYPE - WIRE CHART - OF * Requires additional parts. Automotive Data Solutions Inc.
Page of DOC.: #8 008 TYPE - WIRING DIAGRAM - OF MODULE VEHICLE IGNITI SWITCH A G RF PORT/WEBLINK PORT B F TELEMATIC PORT E C CUT AND INSULATE THE WHITE/YELLOW WIRE (NEXT TO WHITE/GRAY WIRE) WARNING THIS WIRING DIAGRAM IS APPLICABLE LY IF THE REVISI DATE OF THE T-HARSNESS IS AFTER: A VS D SKIM CNECTOR //0 A A VS SKIM HARNESS MS B B PURPLE - ER OUTPUT WHITE/YELLOW - CTROL OUTPUT 8 0 8 0 7 9 7 9 ER - 0 CTROL - 0 MS A B C VEHICLE PARKING LIGHT CNECTI 8 7 0 9 BROWN/BLACK - PARKING LIGHT OUTPUT 0 GRAY - RAP SHUTDOWN OUTPUT WHITE/BROWN - PARKING LIGHT OUTPUT CNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT PARKING LIGHT OR GRAY/GREEN - HORN OUTPUT CNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT 0 AMPS D V OR 8 0 7 9 0 GRAY/WHITE - HOOD STATUS INPUT CNECT IF VEHICLE IS EQUIPPED WITH PARKING LIGHT WITHOUT OEM HOOD SWITCH: INSTALL AND CNECT TO AFTERMARKET HOOD SWITCH PARKING LIGHT 8 87 8 87A 0 PARKING LIGHT OPTIAL DRIVER DOOR PIN HORN AFTERMARKET HOOD SWITCH Automotive Data Solutions Inc.
MODULE PROGRAMMING PROCEDURE - STD KEY - OF Close driver door. Turn key to position. 0 Re-open driver door to wake up data bus. 08 Remove key. 0 Insert key into ignition. 09 Press UNLOCK on the OEM remote. If vehicle is not equipped with OEM remote, press module programming button. Turn key to position. 0 Wait, LED will turn solid GREEN for seconds. 0 LED will turn solid RED. Module Programming Procedure completed. 0 Within seconds, LED will flash GREEN rapidly. 0 Page of DOC.: #8 008 Automotive Data Solutions Inc.
VALET MODE PROGRAMMING PROCEDURE - OF >> 0 Insert key into ignition. Valet Mode Programming Procedure completed. Time restriction. Complete next step within 7 seconds. >> To exit valet mode: repeat steps to. Remove key. 0 0 NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. Page of DOC.: #8 008 Turn key to position then to position five times [x] rapidly. x 0 Wait, LED will turn solid RED for seconds. 0 Turn key to position. Automotive Data Solutions Inc.
Page of DOC.: #8 008 MODULE NAVIGATI PROCEDURE - OF >> It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP. 0 >> Module must be programmed to the vehicle. 0 >> Use the Module Navigation Chart on the next page. 0 Set ignition to position. TO ESS THE MENUS: Press and hold programming button until LED turns solid GREEN. 08 IN THE MENUS: Press the programming button as many times as the menu number indicates. LED will flash GREEN an equal amount of times continuously. 09 0 0 [X] Automotive Data Solutions Inc. TO ESS THE OPTIS: Press and hold programming button until LED turns solid RED. 0 IN THE OPTIS: Press the programming button as many times as the option number indicates. LED will flash RED an equal amount of times continuously. TO ESS THE SETTINGS: Press and hold programming button until LED turns solid GREEN. Configure every other setting and proceed to step. [Z] LED will flash GREEN as many times as the current (or default) setting number, continuously. MANDATORY: EXIT MODULE NAVIGATI. Press and hold programming button for 7 seconds. LED will flash RED rapidly. Release programming button. LED will turn. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED will flash GREEN an equal amount of times continuously. Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. >> Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIS: Press and hold programming button until LED turns solid RED. [Y] LED will flash RED as many times as the current option number continuously.
Page of DOC.: #8 008 [Y] options [X] menus module navigation chart: notes I Default settings are listed in bold. II Make sure the option is covered on the vehicle before attempting to change the setting. 0 0 0 DISARM/UNLOCK BEFORE RELOCK AFTER RELOCK AFTER SHUTDOWN FORCE UNLOCK ALL FIRST PRESS 0 TAKEOVER 0 [Z] settings module navigation chart - OF FACTORY KEYLESS RS SEQUENCE CFIGURATI 08 09 MODULE RUN TIME WAIT TO DELAY off 0 off 0 off 0 off 0 enable 0 DISABLE* DISABLE 0 0 LOCK + UNLOCK + LOCK 0 LocK + LocK + LocK 0 MIN 0 0 MIN 0 0 MIN 0 MIN 0 MIN 0 0 MIN MIN 08 min 0 sec 0 0 SEC 0 08 SEC 0 0 SEC 0 SEC 0 0 SEC SEC 08 0 SEC 0 *Vehicle will shutdown when a door is opened. Automotive Data Solutions Inc.
Page 7 of DOC.: #8 008 [Y] options [X] menus module navigation chart: notes [Z] settings module navigation chart - OF HORN EVENT TRIGGER CFIGURATI 0- Technical Support only HORN CHIRPS WIDTH DoubLe LocK 0 LOCK + UNLOCK 0 LOCK + UNLOCK + 0 DOUBLE LOCK + 0 msec 0 msec 0 0 msec *Vehicle will shutdown when a door is opened. Automotive Data Solutions Inc.
[X] number of PaRKing Light FLashes Diagnostic Remote starter error codes - OF I WARNING: The following applies only when the parking lights are connected and supported by the system. 0 Foot brake is. 0 Hood is open. II After a remote starter failure, the parking lights will flash [X] number times to indicate an error code. See table. 0 Engine tach signal is lost. 0 System is in Valet Mode. Vehicle is moving (VSS). 08 Glow plug timeout error. 09 RS not synchronized. Start vehicle with OEM key for sec before trying a new RS sequence. 0 CAN communication failure during RS sequence. Remote starter error codes: notes Automotive Data Solutions Inc. Page 8 of DOC.: #8 008
I II III DURING PROGRAMMING DURING REMOTE WITH IGNITI Automotive Data Solutions Inc. Diagnostic test module LeD status module Diagnostics - OF Flashing RED Missing/wrong information from firmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN Additional steps required to complete module programming. Solid GREEN then Module correctly programmed. No activity or module already programmed. Flashing RED Module incorrectly programmed. Solid RED Module incorrectly programmed. Flashing GREEN Module correctly programmed and operational. Solid GREEN then Reset in progress. Invalid ground when running status from remote starter. Flashing RED Module incorrectly programmed or connected. Solid RED Module not programmed. Waiting for more vehicle information. Flashing GREEN False ground when running status from remote starter. Solid GREEN then Reset in progress. Module at rest and ready for a remote start sequence. Page 9 of DOC.: #8 008
MODULE RESET PROCEDURE - OF Disconnect all connectors from module except the BLACK 0-PIN connector. Reconnect all connectors. 0 Disconnect the BLACK 0-PIN connector. 08 Repeat programming procedure. 0 PRESS AND HOLD programming button while connecting the BLACK 0-PIN connector. >> Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 0 Wait, LED will flash RED. RELEASE programming button. 0 LED will turn RED for seconds. 0 Module RESET completed. Automotive Data Solutions Inc. Page 0 of DOC.: #8 008
TAKEOVER PROCEDURE - STD KEY - OF >> All vehicle doors must be closed and locked prior to remote start sequence. Press unlock on OEM or aftermarket remote. 0 Insert key into ignition. Failure to follow procedure will result in vehicle engine shutdown. 0 >> Page of DOC.: #8 008 Turn key to position. 0 Press and release BRAKE pedal. 0 Take over procedure completed. Automotive Data Solutions Inc.