Port Solenoid Valve Body Ported Series 000 For details about certified products conforming to international standards, visit us at www.smcworld.com. Type of actuation Type of actuation Rated voltage Body option 100 VAC, 0/0 Hz 200 VAC, 0/0 Hz 110 VAC, 0/0 Hz 220 VAC, 0/0 Hz 24 VDC 12 VDC Other Option How to Order Rated voltage Electrical entry Light/Surge voltage suppressor Body ported 1 2 0 L M 1 2 4 2 position single 2 position double position closed center position exhaust center position pressure center Body option 0: Individual exhaust for the pilot valve (R) port PE port : Common exhaust type for main and pilot valve (R) port 1 2 4 9 PE port 4(A)/2(B) port size Nil: Non-locking push type Option Option F: With foot bracket U: With silencer K: With foot bracket and silencer (2 position single only) B: Locking type B (Slotted) (2 position single type only) Note) The bracket and silencer are not assembled. 4(A), 2(B) port size M M x 0.8 C4 One-touch fitting for ø4 C One-touch fitting for ø Note) 1(P), (R1), (R2) port: M x 0.8 C: Locking type C (Manual) Electrical entry Grommet L plug connector M plug connector DIN terminal G: Lead wire length 00 mm L: With lead wire (Length 00 mm) M: With lead wire (Length 00 mm) MN: Without lead wire D: With connector Light/Surge voltage suppressor Nil Z S None With light/surge voltage suppressor With surge voltage suppressor Not available for GZ, HZ and DOZ H: Lead wire length 00 mm LN: Without lead wire LO: Without connector MO: Without connector DO: Without connector Type LN, MN : With 2 sockets. --17
Series 000 Applicable for cylinder actuation (up to ø40). Compact size (Width: 1 mm) Low power consumption: 1.8 W DC Refer to pages --24 to --27 for manifold use. Made to Order Specifications (For details, refer to page --8.) Specifications Fluid 2 position single Operating pressure 2 position double range (MPa) position Ambient and fluid temperature ( C) Response time (ms) (1) 2 position single, double (at the pressure of 0. MPa) Max. operating frequency (Hz) Effective area (2) Pilot exhaust method Lubrication Mounting orientation Impact/Vibration resistance (m/s 2 ) () Enclosure Note 1) Based on dynamic performance test, JIS B 87-1981. (Coil temperature: 20 C, at rated voltage, without surge suppressor) Note 2) When operating the locking type manually, apply torque of 0.2 N m or less. Note ) Impact resistance: No malfunction occurred when it is tested with a drop tester in the axial direction and at the right angles to the main valve and armature in both energized and de-energized states every once for each condition. (Values at the initial period) Vibration resistance: No malfunction occurred in a one-sweep test between 4 and 2000 Hz. Test was performed at both energized and de-energized states in the axial direction and at the right angles to the main valve and armature. (Values at the initial period) Solenoid Specifications Electrical entry AC 0/0 Hz Coil rated voltage (V) DC Allowable voltage fluctuation (%) Power consumption (W) Note) [Current ma] DC Note) Apparent power (VA) [Current ma] Surge voltage suppressor Indicator light Note) At rated voltage Option Description With foot bracket Silencer position 2 position single, double position AC Part no. DXT170-4-1B AN120-M Inrush Holding Air 0.1 to 0.7 0.1 to 0.7 0.1 to 0.7 10 to 0 C (No freezing. Refer to page -1-4.) 20 or less or less 10 Refer to the table below. Non-locking push type, Locking slotted type, Locking lever type Individual pilot exhaust type, Common exhaust (pilot and main valve) type Not required Unrestricted 00/0 Dustproof Grommet (G)/(H), L plug connector (L), M plug connector (M), DIN terminal (D) 100, 200, 24, 48, 110, 220 24,, 12, 48 1 to +10% of rated voltage 1.8 (With indicator light 2.1) [24 VDC: 7 (With indicator light 87.)] Option 100 VAC: 4/0 Hz, 42/0 Hz 4./0 Hz, 4.2/0 Hz 200 VAC: 22./0 Hz, 21/0 Hz 100 VAC: /0 Hz, 0/0 Hz./0 Hz, /0 Hz 200 VAC: 17./0 Hz, 1/0 Hz DC: Diode, AC: ZNR DC: LED (Red), AC: Neon bulb Note For 12 0 Noise reduction: 21dB or more (ø8 x 17 mm) --18
Port Solenoid Valve Body Ported Series 000 Flow Characteristics/Weight Valve model 20- -M 20- -C4 20- -C 2 position position 2 position position 2 position position Type of actuation Single Double Closed center Exhaust center Pressure center Single Double Closed center Exhaust center Pressure center Single Double Closed center Exhaust center Pressure center Port size 1,, (P, EA, EB) M x 0.8 M x 0.8 M x 0.8 4, 2 (A, B) M x 0.8 C4 (One-touch fitting for ø4) C (One-touch fitting for ø) It is when the cylinder is extending that is meter-out controlled by speed controller which is directly connected with cylinder, and its needle valve with being fully open. The average velocity of the cylinder is what the stroke is divided by the total stroke time. Load factor: ((Load weight x 9.8)/Theoretical force) x 100% Flow characteristics Note) 1 4/2 (P A/B) 4/2 / (A/B EA/EB) C [dm /(s bar)] 0.47 b 0.41 Cv 0.1 C [dm /(s bar)] 0.47 b 0.41 Cv 0.1 0.49 0.4 0.49 [0.9] 0.9 0.9 0. 0.7[0.41] 0.70 0.72 0.7 0.82 [0.44] Note) [ ]: Denotes the normal position. Exhaust center: 4/2 /, Pressure center: 1 4/2 Cylinder Speed Chart Series 120-M Average speed (mm/s) 800 700 00 00 400 00 200 100 0 0.44 0.7 0.1 [0.8] 0.1 0.12 0.14 [0.10] 0.9 0.18 0.40 0.19 0.40 0.1 0.4 [0.7] 0.1 [0.10] 0. 0.7 0.4 0.41 [0.9] 0.19 0.19 0.19 0.2 [0.12] Use as a guide for selection. Please confirm the actual conditions with SMC Sizing Program. Bore size Series CJ2 Pressure 0. MPa Load factor 0% Stroke 0 mm Series CM2 Pressure 0. MPa Load factor 0% Stroke 00 mm ø ø10 ø1 ø20 ø2 ø2 ø40 Perpendicular, upward actuation Horizontal actuation 0.44 0.47 [0.9] 0.4 0.44 0.4 0.41 [0.41] 0.41 0.47 0.44 0.41 [0.41] 0.41 0.40 0.4 [0.] 0.42 0.9 0.40 0.12 0.7 [0.7] 0.10 [0.11] 0.7 0.10 0.40 0.4 0.8 [0.8] 0. 0.12 0.1 [0.10] 0.12 0.12 0.12 0.12 0.11 [0.11] 0.11 Weight (g) Grommet 7 120 10 7 120 10 7 120 10 Conditions SZ120-M Body ported Tube bore x Length Speed controller Silencer Series CJ2 ø4 x 1 m AS101F-04 AN120-M Series CM2 ø x 1 m AS01F-0 AN110-01 Series MB ø8 x 1 m AS01F-08 --19
Series 000 Construction 2 position single 2 position double position closed center position closed center/exhaust center/pressure center position exhaust center position pressure center (This figure shows a closed center type.) Component Parts No. Description q Body w Piston plate e Piston r Spool valve t End cover y Spool spring Material Aluminum die-casted Resin Resin Aluminum, HNBR Resin Stainless steel Note Platinum silver Black Replacement Parts No. u i Description Material Part no. Note Solenoid assembly Epoxy/Stainless steel DXT170-C- Common with O-ring NBR 1 x 11 x 1 1 Series 000 --20
Port Solenoid Valve Body Ported Series 000 2 Position Single Grommet (G), (H) 120- -M G H Mounting hole for manifold 120 Bracket (Non-locking) G: 00 mm H: 00 mm (Mounting screw) (Mounting hole) (PE port) (Mounting hole) (Piping port) L plug connector (L) 120- L -M M plug connector (M) 120- M -M DIN terminal (D) 120- D -M MAX. 10 Applicable cable O.D. ø. to ø7 Built-in One-touch fittings 120- - C4 C C4: MAX. 7 C: MAX. 7. : With light/surge voltage suppressor 2-One-touch fitting (A, B port) Applicable tubing model C4: T042 C: T004 --21
Series 000 2 Position Double 220 Grommet (G), (H) 220- -M G H (Non-locking) Mounting hole for manifold G: 00 mm H: 00 mm (Mounting hole) (PE port) (Piping port) L plug connector (L) 220- L -M M plug connector (M) 220- M -M : With light/surge voltage suppressor DIN terminal (D) 220- D -M Built-in One-touch fittings C4 220- - C MAX. 10 Applicable cable O.D. ø. to ø7 C4: MAX. 7 C: MAX. 7. 2-One-touch fitting (A, B port) Applicable tubing model C4: T042 C: T004 --22
Port Solenoid Valve Body Ported Series 000 Position Closed Center/Exhaust Center/Pressure Center Grommet (G), (H) 4 G 20- -M H 20 420 (Non-locking) (Mounting hole for manifold) (Mounting hole) G: 00 mm H: 00 mm 2-M x 0.8 (PE port) 20 (Piping port) L plug connector (L) 420- L -M M plug connector (M) 420- M -M : With light/surge voltage suppressor DIN terminal (D) 420- D -M Built-in One-touch fittings 4 20- - C4 C MAX. 10 Applicable cable O.D. ø. to ø7 C4: MAX. 7 C: MAX. 7. 2-One-touch fitting (A, B port) Applicable tubing model C4: T042 C: T004 --2
Series 000/Body Ported Manifold Specifications Manifold Standard Manifold Specifications Model Manifold type P(SUP)/R(EXH) Valve stations 4(A), 2(B) port location 1(P), /(R) port Port size 4(A), 2(B) port Flow Characteristics Body ported For internal pilot Manifold Port size 1(P), /(R) port 2 (B), 4(A) port Type 20 Single base/b mount Common SUP/Common EXH 2 to 20 stations Valve Rc 1 8 M x 0.8, C4, C 1/8 M x 0.8 0.4 0.9 Type V-20 2 1/8 C4 0.2 0. 1/8 C 0.79 0. Note) Value at manifold base mounted, 2 position single operating Flow characteristics 1 4/2 (P A/B) 4/2 / (A/B R) C [dm /(s bar)] b Cv C [dm /(s bar)] b Cv 0.12 0.1 0.21 0.7 0.8 0.91 0.2 0.27 0. 0.19 0.20 0.24 Flat Ribbon Cable Manifold One-touch wiring to consolidate connection of external wires. Clean appearance The flat cable provides wiring on a printed circuit board to the individual valves at the manifold base, enabling the consolidation of external wiring at a touch through a 2 pins MIL connector. How to Order Manifold Instruct by specifying the valves and blanking plate assembly to be mounted on the manifold along with the manifold base model no. (Example) V-20-01... 1 pc. (Manifold base) 120-G-M... 2 pcs. (Valve) DXT192-1-1A... 1 pc. (Blanking plate assembly) The asterisk denotes the symbol for assembly. Prefix it to the part nos. of the solenoid valve, etc. Flat Ribbon Cable Manifold Specifications Model Manifold type P(SUP), R(EXH) Valve stations 4(A), 2(B) port location 1(P), /(R) port Port size 4(A), 2(B) port Applicable flat ribbon cable connector Internal wiring Applicable valve model Type 20P Single base/b mount Common SUP/Common EXH to 12 stations Valve Rc 1 8 M x 0.8, C4, C Socket: 2 pins MIL, with strain relief (Conforming to MIL-C-80) + COM (For COM specifications, specify them separately.) 2- MOZ - Rated voltage 100 VAC 0/0 Hz, 110 VAC 0/0 Hz, 24 VDC, 12 VDC Note ) Withstand voltage specifications of wiring unit part is equivalent to JIS C 0704 class 1. 1 M C4 C --24 Flow Characteristics Body ported For internal pilot Manifold How to Order Manifold 1(P), /(R) port 1/8 1/8 Port size 2(B), 4(A) port M x 0.8 C4 C Type V-20P 2 1/8 0.79 0. Note) Value at manifold base mounted, 2 position single operating Flow characteristics 1 4/2 (P A/B) 4/2 / (A/B R) C [dm /(s bar)] b Cv C [dm /(s bar)] b Cv 0.4 0.2 0.9 0. 0.12 0.1 0.21 0.7 0.8 0.91 0.2 0.27 0. 0.19 0.20 0.24 Instruct by specifying the valves, blanking plate assembly and connector assembly to be mounted on the manifold along with the manifold base model no. (Example) V-20P-07... 1 pc. (Manifold base) 12-MOZ-C4... pcs. (Valve) 22-MOZ-C4... pcs. (Valve) DXT192-1-A... 1 pc. (Blanking plate assembly) DXT192-2-1-4A... pcs. (Connector assembly) DXT192-2-2-4A... pcs. (Connector assembly) The asterisk denotes the symbol for assembly. Prefix it to the part nos. of the solenoid valve, etc.
Port Solenoid Valve Body Ported Series 000 Common SUP/Common EXH Type 20 How to Order 4(A), 2(B) port Flat Ribbon Cable Type 20P How to Order 4(A), 2(B) port Option Applicable base V-20 V-20P V-21 V 20 0 1 Stations 02 2 stations 20 20 stations V 20P 0 Combinations of Solenoid Valve, Gasket and Manifold Base Round head combination screw (With spring washer) Individual EXH Spacer Assembly DXT192-21-1A Round head combination screw M2. x (With spring washer) 1(P) port Rc 1/8 / (R) port Rc 1/8 1(P) port Rc 1/8 / (R) port Rc 1/8 0 Stations stations 12 12 stations Gasket P, R port thread type Nil 00F 00N 00T Rc G NPT NPTF P, R port thread type Nil Rc 00F G 00N NPT 00T NPTF Applicable solenoid valve G L M 2 - M - C4 D C Applicable blanking plate assembly DXT192-1-1A Individual EXH spacer assembly DXT192-21-1A Individual SUP spacer assembly DXT192-40-2A Blanking Plate Assembly DXT192-1-1A Applicable base V-20 V-21 DXT192-1-A Applicable solenoid valve 1 M 2- MOZ - C4 C Applicable blanking plate assembly DXT192-1-A Applicable connector assembly DXT192-2-1- A (For 2 position single) DXT192-2-2- A (For 2 position double, position) Refer to the page -10- regarding how to order applicable connector assemblies. (1: 100 VAC, : 110 VAC, 4: DC). Round head combination screw M2. x 7 (With spring washer) Blanking plate Gasket Round head combination screw M2. x 7 (With spring washer) Blanking plate Gasket Option Installation of the 00 Valve on the 000 Manifold Use of an adaptor plate makes it possible to mount Series 00 on the manifold base of Series 000. The mounting direction is shown in the diagram below. Mount the solenoid so that it will be on the same side as the single solenoid of the Series 000. Adapter plate assembly DXT200--2A Manifold gasket Applicable base V-20 V-21 Individual SUP Spacer Assembly DXT192-40-2A Round head combination screw M2. x 40. (With spring washer) Series 00 Body ported Adapter plate assembly Round head combination screw Adapter plate Adapter gasket Dust cap Gasket ((R1), (R2) port) Individual EXH spacer Applicable base V-20 V-21 Gasket Gasket Caution Applicable base V-20P Note) Please contact SMC when using an individual SUP spacer assembly, an individual EXH spacer assembly, or an adapter plate assembly on type 20P. Mounting Screw Tightening Torques M2.: 0.4 N m Rc 1/8 1(P) port Individual SUP spacer Gasket Applicable base V-20 V-21 --2
Series 000 Grommet (G), (H) Type 20 Manifold V-20- Station 1 (4(A), 2(B) port) (Mounting hole) (Non-locking) G: 00 mm H: 00 mm -Rc 1/8 (1(P), /(R) port) (PE port) Stations 2 L1 8 74 L2 40 4 90 72 10 88 122 104 7 18 120 8 14 1 9 170 12 10 18 18 11 202 184 12 218 200 1 24 21 14 20 22 1 2 248 1 282 24 17 298 280 18 14 29 19 0 12 (mm) 20 4 28 L plug connector (L) M plug connector (M) DIN terminal (D) Built-in One-touch fittings C4: MAX. 7 C: MAX. 7. Applicable cable O.D. ø. to ø7 2n-One-touch fitting (A, B port) Applicable tubing model C4: T042 C: T004 : With light/surge voltage suppressor --2
Port Solenoid Valve Body Ported Series 000 Type 20P Flat Ribbon Cable Manifold V-20P- Station (Non-locking) 4(A), 2(B) port (Mounting hole) -Rc 1/8 1(P), /(R) port (Light/Surge voltage suppressor) Triangle mark (Station n)(station 1) Connector polarity indicator Applicable connector: 2 pins MIL (Conforming to MIL-C-80) (mm) Stations 4 L1 77 94. 112 L2 9 7. 94 129. 111. 7 147 129 8 14. 14. 9 182 14 10 199. 181. 11 217 199 12 24. 21. Built-in One-touch fittings C4: MAX. 7 C: MAX. 7. 2n-One-touch fitting (A, B port) Applicable tubing model C4: T042 C: T004 --27
Port Solenoid Valve Base Mounted Series 000 For details about certified products conforming to international standards, visit us at www.smcworld.com. Non plug-in 1 4 0 L 1 2 Type of actuation 2 position single Type of actuation Body option Body option How to Order Rated voltage Electrical entry Plug-in 1 4 F Z 2 position double position closed center 0: Individual exhaust for the pilot valve (R) port PE port : Common exhaust type for main and pilot valve Note) Light/Surge voltage suppressor Port size Thread type Nil F N T Port size Thread type Rc G NPT NPTF Nil: Without sub-plate Note) Please contact SMC in the case of without indicator light. 01: Rc 1 8 With sub-plate (R) port PE port /Plug-in type Nil: Non-locking push type B: Locking type B (Slotted) C: Locking type C (Manual) 4 position exhaust center position pressure center 1 2 4 9 Option Rated voltage 100 VAC, 0/0 Hz 200 VAC, 0/0 Hz 110 VAC, 0/0 Hz 220 VAC, 0/0 Hz 24 VDC 12 VDC Other /Non plug-in type Nil: Non-locking push type 1 0 B: Locking type B (Slotted) 1 0 C: Locking type C (Manual) Electrical entry Grommet L plug connector M plug connector DIN terminal G: Lead wire length 00 mm L: With lead wire (Length 00 mm) M: With lead wire MN: Without lead wire (Length 00 mm) D: With connector Light/Surge voltage suppressor H: Lead wire length 00 mm LN: Without lead wire LO: Without MO: Without DO: Without connector connector connector Nil Z S None With light/surge voltage suppressor With surge voltage suppressor Not available for GZ, HZ and DOZ Type LN, MN : With 2 sockets. --29
Series 000 Applicable for cylinder actuation (up to ø40). Compact size (Width: 1 mm) Low power consumption: 1.8 W DC Specifications Fluid Operating pressure range (MPa) Ambient and fluid temperature ( C) Response time (ms) (1) 2 position single, double (at the pressure of 0. MPa) Max. operating frequency (Hz) 2 position single 2 position double position position 2 position single, double position (2) Pilot exhaust method Lubrication Mounting orientation Impact/Vibration resistance (m/s 2 ) () Enclosure Air 0.1 to 0.7 0.1 to 0.7 0.1 to 0.7 10 to 0 C (No freezing. Refer to page -1-4.) 20 or less or less 10 Non-locking push type, Locking slotted type, Locking lever type Individual pilot exhaust type, Common exhaust (pilot and main valve) type Not required Unrestricted 00/0 Dustproof Note 1) Based on dynamic performance test, JIS B 87-1981. (Coil temperature: 20 C, at rated voltage, without surge suppressor) Note 2) When operating the locking type manually, apply torque of 0.2 N m or less. Note ) Impact resistance: No malfunction occurred when it is tested with a drop tester in the axial direction and at the right angles to the main valve and armature in both energized and de-energized states every once for each condition. (Values at the initial period) Vibration resistance: No malfunction occurred in a one-sweep test between 4 and 2000 Hz. Test was performed at both energized and de-energized states in the axial direction and at the right angles to the main valve and armature. (Values at the initial period) Refer to pages --7 to --2 for manifold use. Solenoid Specifications Electrical entry AC 0/0 Hz Coil rated voltage (V) DC Allowable voltage fluctuation (%) Power consumption (W) (1) [Current ma] DC Apparent power (VA) (1) [Current ma] Note) AC Surge voltage suppressor Indicator light Note 1) At rated voltage Note 2) Plug-in should be ZNR. Inrush Holding Grommet (G)/(H), L plug connector (L), M plug connector (M), DIN terminal (D) 100, 200, 24, 48, 110, 220 24,, 12, 48 1 to +10% of rated voltage 1.8 (With indicator light 2.1) [24 VDC: 7 (With indicator light 87.)] Option 100 VAC: 4/0 Hz, 42/0 Hz 4./0 Hz, 4.2/0 Hz 200 VAC: 22./0 Hz, 1/0 Hz 100 VAC: /0 Hz, 0/0 Hz./0 Hz, /0 Hz 200 VAC: 17./0 Hz, 1/0 Hz DC: Diode, AC: ZNR (2) DC: LED (Red), AC: Neon bulb Combinations of Solenoid Valve and Gasket Made to Order Specifications (For details, refer to page --8.) Round head combination screw M2. x 2 (With spring washer) Gasket DXT192-10- (Use caution to the orientation.) --0
Port Solenoid Valve Base Mounted Series 000 Flow Characteristics/Weight Valve model 40- -01 Note 1) [ ]: Denotes the normal position. Exhaust center: 4/2 /, Pressure center: 1 4/2 Note 2) ( ): Without sub-plate. Cylinder Speed Chart Series 14 - -01 (Piping: ø4 x 1 m) Speed controller/silencer 14 - -01 (Piping: ø x 1 m) Speed controller/silencer Series 2 position position 14 - -01 (Piping: ø x 1 m) Speed controller/silencer Type of actuation Single Double Closed center Exhaust center Pressure center Average speed (mm/s) Average speed (mm/s) 800 700 00 00 400 00 200 100 800 700 00 00 400 00 200 100 800 700 00 00 400 00 200 100 Port size 1,, (P, EA, EB) Rc 1/8 4, 2 (A, B) Rc 1/8 Flow characteristics (1) 1 4/2 (P A /B) 4/2 / (A/B EA/EB) C [dm /(s bar)] 0.79 0.80 b 0.21 0.28 Cv 0.19 0.18 C [dm /(s bar)] 0.8 0.8 b 0.2 0.4 Cv 0.21 0.20 0.71 0.2 0.18 1.1 [0.0] 0.24 [0.44] 0.2 [0.18] 0.99 [0.47] 0.29 [0.8] 0.24 [0.12] 0.72 0.8 0.18 Use as a guide for selection. Please confirm the actual conditions with SMC Sizing Program. Bore size Series CM2 Pressure 0. MPa Load factor 0% Stroke 00 mm ø20 ø2 ø2 ø40 AS201F- 01-04 /AN110-01 AS01F- 02-0 /AN110-01 Perpendicular, upward actuation Horizontal actuation Perpendicular, upward actuation Horizontal actuation Bore size Series CA1 Pressure 0. MPa Load factor 0% Stroke 400 mm ø40 ø0 ø ø80 AS01F- 02-0 /AN110-01 ø100 Perpendicular, upward actuation Horizontal actuation Weight (g) Grommet 12 (7) 170 (120) 180 (10) 14 - -01 (Piping:ø8 x 1 m) 800 700 00 00 400 00 200 100 Perpendicular, upward actuation Horizontal actuation Speed controller/silencer AS01F- 02-08 /AN110-01 It is when the cylinder is extending that is meter-out controlled by speed controller which is directly connected with cylinder, and its needle valve with being fully open. The average velocity of the cylinder is what the stroke is divided by the total stroke time. Load factor: ((Load weight x 9.8)/Theoretical force) x 100% --1
Series 000 Built-in Speed Controllers An exhaust throttle valve is built into the solenoid valve itself, enabling a simple speed adjustment of the cylinder. If it is mounted on a manifold base, the exhaust air will converge in the common EXH port at the manifold base, thus simplifying the handling of the exhaust air. Throttle Valve Characteristics ( A B R) Effective area (mm 2 ) JIS Symbol (Single) How to Order Valve with Built-in Speed Controller Non plug-in (Fully closed) Numbers of needle rotations (turns) (Fully open) Note) To use the, open the throttle valve one turn or more from the fully closed position. To adjust the throttle valve apply torque of 0. N m or less. Be careful not to open the throttle valve excessively as this could cause the throttle valve to fly out. Type of actuation Body option Rated voltage Electrical entry Thread type Port size Light/Surge voltage suppressor --2
Port Solenoid Valve Base Mounted Series 000 Construction 2 position single 2 position double position closed center position closed center/exhaust center/pressure center position exhaust center position pressure center (This figure shows a closed center type.) Component Parts No. Description q Body w Piston plate e Piston r Spool valve t End cover y Spool spring Material Aluminum die-casted Resin Resin Aluminum, HNBR Resin Stainless steel Note Platinum silver Black Replacement Parts No. u i o Description Material Part no. Note Sub-plate Aluminum die-casted DXT192-14-1 P Platinum silver Solenoid assembly Epoxy/Stainless steel DXT170-C- O-ring NBR 1 x 11 x 1 Common with 1 Series 000 Thread type Nil: Rc F: G N: NPT T: NPTF --
Series 000 2 Position Single Grommet (G), (H) 140- G -01 H 140 G: 00 mm H: 00 mm (Non-locking) (Mounting hole) (Mounting hole pitch) (Mounting hole pitch) (Piping port) (PE port) L plug connector (L) 140- L -01 M plug connector (M) 140- M -01 : With light/surge voltage suppressor DIN terminal (D) 140- D -01 Applicable cable O.D. ø. to ø7 Built-in speed controllers 10- --4
Port Solenoid Valve Base Mounted Series 000 2 Position Double 240 Grommet (G), (H) 240- -01 G H (Non-locking) (Mounting hole) (Mounting hole pitch) G: 00 mm H: 00 mm (Mounting hole pitch) (PE port) (Piping port) L plug connector (L) 240- L -01 M plug connector (M) 240- M -01 : With light/surge voltage suppressor DIN terminal (D) 240- D -01 Built-in speed controllers 20- Applicable cable O.D. ø. to ø7 --
Series 000 Position Closed Center/Exhaust Center/Pressure Center Grommet (G), (H) G 420- H -01 40 440 (Non-locking) (Mounting hole) (Mounting hole pitch) 40 G: 00 mm H: 00 mm (Mounting hole pitch) 2-M x 0.8 (PE port) 4-Rc 1/8 (Piping port) L plug connector (L) 440- L -01 M plug connector (M) 440- M -01 : With light/surge voltage suppressor DIN terminal (D) 440- D -01 Built-in speed controllers 4 0- Applicable cable O.D. ø. to ø7 MAX. 10 MAX. 11 --
Manifold Standard Series 000/Base Mounted Manifold Specifications One-touch wiring to consolidate connection of external wires. Clean appearance The flat cable provides wiring on a printed circuit board to the individual valves at the manifold base, enabling the consolidation of external wiring at a touch through a 2 pins MIL connector. Manifold Specifications Model Manifold type P(SUP)/R(EXH) Valve stations 4(A), 2(B) port Position Porting specifications Direction 1(P), /(R) port Port size Flat Ribbon Cable Manifold 4(A), 2(B) port Flow Characteristics How to Order Manifold Position Direction 1(P), /(R) port 4(A), 2(B) port Type 40 Type 41 Type 42 Type 4 Single base/b mount Common SUP/Common EXH 2 to 20 stations Base Base Bottom Side Rc 1/8 Rc 1/4 Rc 1/8 M x 0.8 Flat Ribbon Cable Manifold Specifications Manifold type P(SUP), R(EXH) Valve stations 4(A), 2(B) port location Port size Internal wiring Model Applicable flat ribbon cable connector Applicable valve model 4- MOZ - - MOZ Rated voltage 100 VAC 0/0 Hz, 110 VAC 0/0 Hz, 24 VDC, 12 VDC Note) Withstand voltage specifications of wiring unit part is equivalent to JIS C 0704 class 1. 1 C B7 Rc 1/8 One-touch fitting for ø One-touch fitting for 1/4" 1 C4 B One-touch fitting for ø4 One-touch fitting for /2" Port size Flow characteristics Manifold 1(P), /(R) 2(B), 4(A) 1 4/2 (P A/B) 4/2 / (A/B R) port port C [dm /(s bar)] b Cv C [dm /(s bar)] b Cv V-40 1/8 M x 0.8 0. 0. 0.1 0.4 0.2 0.1 V-41 1/8 M x 0.8 0.9 0. 0.1 0.8 0.2 0.17 V-42-01 4 1/4 1/8 0.74 0.22 0.18 0.82 0.1 0.21 V-42-C 1/4 C 0.71 0.24 0.17 0.80 0.29 0.20 V-4 1/8 C4 0. 0.29 0.14 0.74 0.2 0.19 Note) Value at manifold base mounted, 2 position single operating Instruct by specifying the valves and blanking plate assembly to be mounted on the manifold along with the manifold base model no. (Example) V-40-01-M1 pc. (Manifold base) 140-G-M2 pcs. (Valve) DXT192-1-1A1 pc. (Blanking plate assembly) V-4-01-C41 pc. (Manifold base) 140-LZ 1 pc. (Valve) 240-LZ 1 pc. (Valve) DXT192-1-1A1 pc. (Blanking plate assembly) The asterisk denotes the symbol for assembly. Prefix it to the part nos. of the solenoid valve, etc. Type 41P Type 4P Single base/b mount Common SUP/Common EXH to 12 stations Base Side Rc 1/8 Rc 1/8 M x 0.8 C4 (One-touch fitting for ø4) Socket: 2 pins MIL, with strain relief (Conforming to MIL-C-80) +COM specifications (For COM specifications, specify them separately.) Flow Characteristics Port size Flow characteristics Manifold 1(P), /(R) 2(B), 4(A) 1 4/2 (P A/B) 4/2 / (A/B R) port port C [dm /(s bar)] b Cv C [dm /(s bar)] b Cv V-41P 1/8 M x 0.8 0.9 0. 0.1 0.8 0.2 0.17 SYJ 4 V-4P 1/8 C4 0.9 0.29 0.14 0.74 0.2 0.19 Note) Value at manifold base mounted, 2 position single operating How to Order Manifold Instruct by specifying the valves, blanking plate assembly and connector assembly to be mounted on the manifold along with the manifold base model no. (Example) V-4P-07-C4 1 pc. (Manifold base) 14-MOZ pcs. (Valve) 24-MOZ pcs. (Valve) DXT192-1-A 1 pc. (Blanking plate assembly) DXT192-2-1-4A pcs. (Connector assembly) DXT192-2-2-4A pcs. (Connector assembly) The asterisk denotes the symbol for assembly. Prefix it to the part nos. of the solenoid valve, etc. --7
Series 000 Common SUP/Common EXH Type 40 1(P) port Rc 1/8, (R) port 4(A), 2(B) port Rc 1/8 M x 0.8 Note) For more than 8 stations, supply air to both sides of 1(P) port and exhaust air from both sides of /(R) port. How to Order V 40 0 2 M 02 20 Stations 2 stations 20 stations 4(A), 2(B) port size M M x 0.8 1(P), /(R) port thread type Nil Rc F G N NPT Z NPTE Type 41 How to Order V 41 0 1 M 4(A), 2(B) port M x 0.8 Type 42 4(A), 2(B) port Rc 1/8, C Type 4 /(R) port Rc 1/8 1(P) port Rc 1/8 /(R) port Rc 1/4 1(P) port Rc 1/4 02 20 02 20 Stations V 42 0 1 C Stations 2 stations 20 stations 2 stations 20 stations How to Order How to Order 4(A), 2(B) port size 4(A), 2(B) port size 01 Rc 1 8 C One-touch fitting for ø B7 One-touch fitting for 1/4" 1(P), /(R) port thread type M M x 0.8 Nil Rc F G N NPT Z NPTE 1(P), /(R) port thread type Rc G NPT NPTE V 4 0 1 C4 Nil F N Z Applicable solenoid valve G L 4 - M D G - L M D Applicable blanking plate assembly DXT192-1-1A Applicable individual EXH spacer assembly DXT192-21-1A Applicable individual SUP spacer assembly (Except V-40 type) DXT192-40-1A Applicable interface regulator ARBZ000-00-P 4(A), 2(B) port /(R) port Rc 1/8 1(P) port Rc 1/8 02 20 Stations 2 stations 20 stations 4(A), 2(B) port size C4 One-touch fitting for ø4 B One-touch fitting for /2" 1(P), /(R) port thread type Nil F N Z Rc G NPT NPTE Flat ribbon cable type 41P 4(A), 2(B) port M x 0.8 1(P) port Rc 1/8 /(R) port Rc 1/8 Flat ribbon cable type 4P 4(A), 2(B) port C4 1(P) port Rc 1/8 /(R) port Rc 1/8 0 12 V 41P 0 M 0 12 V 4P 0 C4 Stations How to Order stations 12 stations Stations stations 12 stations How to Order 4(A), 2(B) port size M M x 0.8 Nil F N Z Rc G NPT NPTE 4(A), 2(B) port size C4 One-touch fitting for ø4 B One-touch fitting for /2" 1(P), /(R) port thread type 1(P), /(R) port thread type Nil Rc F G N NPT Z NPTE Applicable solenoid valve 1 4- MOZ 1 - MOZ Applicable blanking plate assembly DXT192-1-A Applicable connector assembly DXT192-2-1- A (For 2 position single) DXT192-2-2- A (For 2 position double, position) 1: 100 VAC, : 110 VAC, 4: DC For How to order applicable connector assemblies, refer to page --7. --8
Port Solenoid Valve Base Mounted Series 000 DIN Rail Manifold DIN Rail Manifold Common SUP/Common EXH Type 4 (Non plug-in type) How to Order Type 4F (Plug-in type) Stations 02 2 stations 02 20 20 V 20 stations U D B M How to Order Manifold Specifications Model Type 4 Type 4F Manifold type Stacking type non plug-in type Stacking type plug-in type P(SUP), R(EXH) Common SUP/Common EXH Valve stations 2 to 20 stations A, B port Location Base Porting specifications Direction Side 1(P), /(R) port C8 (One-touch fitting for ø8) Port size C4 (One-touch fitting for ø4) 4(A), 2(B) port C (One-touch fitting for ø) Connector MIL-C-2408 Applicable for JIS-X-101 D-sub connector Internal wiring COM Note) Note) It is available at +COM or COM. Port size Flow characteristics Manifold 1(P), /(R) 2(B), 4(A) 1 4/2 (P A/B) 4/2 / (A/B R) port port C [dm /(s bar)] b Cv C [dm /(s bar)] b Cv C8 C4 0.9 0.28 0.1 0.8 0.4 0.22 V-4 4 C8 C 0.7 0.2 0.18 0.8 0.29 0.22 Note) Value at manifold base mounted, 2 position single operating How to Order Manifold 4 0 D C SUP/EXH block mounting position U side: 2 to 10 stations D side: 2 to 10 stations Both sides: 2 to 20 stations Special specifications For special specifications, indicate separately by the manifold specification sheet. V U D B Connector mounting direction U side: 2 to 10 stations D side: 2 to 10 stations Both sides: 11 to 20 stations Stations 2 stations 20 stations Flow Characteristics Instruct by specifying the valves and blanking plate assembly to be mounted on the manifold along with the manifold base model no. (Example) V-4FD-0-CC 1 pc. (Manifold base) 14-FZ2 pcs. (Valve) 24-FZ pcs. (Valve) 000-9-1A 1 pc. (Blanking plate assembly) The asterisk denotes the symbol for assembly. Prefix it to the part nos. of the solenoid valve, etc. Nil B M SUP/EXH block mounting position For 2 to 10 stations : One side (Same as direction of connector mount) For 11 to 20 stations: Both sides For 2 to 10 stations: Both sides Special specifications For special specifications, indicate separately by the manifold specification sheet. C 4(A), 2(B) port size One-touch C4 fitting for ø4 One-touch C fitting for ø M Mixed In the case of mixed specifications (M), indicate separately on the manifold specification sheet. 4F D 0 C C 4(A), 2(B) port size One-touch C4 fitting for ø4 One-touch C fitting for ø M Mixed In the case of mixed specifications (M), indicate separately on the manifold specification sheet. Applicable solenoid valve G 4 - L M D G - L M D Applicable blanking plate assembly 000-9-2A DIN rail length specified Nil Standard length For stations (Specify a longer rail than the 20 For 20 stations standard length.) Applicable solenoid valve 4- FZ Applicable blanking plate assembly 000-9-1A DIN rail length specified Nil Standard length For stations (Specify a longer rail than the 20 For 20 stations standard length.) --9
Series 000 Option/Standard Manifold, Flat Ribbon Cable Manifold Combinations of Solenoid Valve, Manifold Gasket and Manifold Base Round head combination screw (With spring washer) Applicable base V-40 V-41 V-42 V-4 V-41P V-4P Gasket DXT192-10- (Use caution to the orientation.) Installation of the 00 Valve on the 000 Manifold Use of an adaptor plate makes it possible to mount Series 00 on the manifold base of Series 000. The mounting direction is shown in the diagram below. Mount the solenoid so that it will be on the same side as the single solenoid of the Series 000. 2(A) port of port valve should be 2(B) port of manifold base. Adapter Plate Assembly DXT200--1A Adapter plate assembly Applicable base V-40 V-41 V-42 V-4 Series 00 Base mounted Blanking Plate Assembly DXT192-1-1A DXT192-1-A Round head combination screw M2. x 7 (With spring washer) Blanking plate Gasket Applicable base V-40 V-41 V-42 V-4 Round head combination screw M2. x 7 (With spring washer) Blanking plate Gasket Manifold gasket Round head combination screw Adapter plate Dust cap Individual EXH Spacer Assembly DXT192-21-1A Spring washer for M2. Round head combination screw Corresponding mark Applicable base V-40 V-41 V-42 V-4 Individual SUP Spacer Assembly DXT192-40-1A Spring washer for M2. Round head combination screw Adapter gasket Applicable base V-41P V-4P Interface regulator (P port regulation) Interface regulator can be placed on top of the manifold base to reduce the pressure of each of the valves. ARBZ000-00-P Round head combination screw (With spring washer) Gasket ((R1), (R2) port) --40 Gasket Individual EXH spacer Rc 1/8 (1(P) port) Note) Please contact SMC when using an individual EXH spacer assembly, an individual SUP spacer assembly, an adapter plate assembly, or an interface regulator on 41P and 4P types. Applicable base V-41 V-42 V-4 Individual SUP spacer Caution Gasket Mounting Screw Tightening Torques Applicable base V-40 V-41 V-42 V-4 Before using, refer to page --8. M2.: 0.4 N m
Port Solenoid Valve Base Mounted Series 000 Option/DIN Rail Manifold Blanking Plate Assembly 000-9-2A Combination of Solenoid Valve, Gasket and Manifold Base Round head combination screw Round head combination screw Round head combination screw (With spring washer) (With spring washer) (With spring washer) Blanking plate Gasket 000-9-1A Dust cap Applicable base V-4 Round head combination screw (With spring washer) Blanking plate Gasket (Use caution to the orientation.) Gasket DXT192-10- (Use caution to the orientation.) Applicable base V-4 SUP Block Disk By installing a SUP block disk in the pressure supply passage of a manifold valve, it is possible to supply two or more different high and low pressures to one manifold. 000-79-1A Gasket DXT192-10- (Use caution to the orientation.) Applicable base V-4F EXH Block Disk By installing an EXH block disk in the exhaust passage of a manifold valve, it is possible to divide the valve s exhaust so that it does not affect another valve. 000-79-1A Applicable Plug Assembly (D-sub connector cable assembly) Caution Applicable base V-4F Mounting Screw Tightening Torques M2.: 0.2 N m (For stacking type manifold) Cable length Assembly part no. 1. m V000-21A-1 m V000-21A-2 m V000-21A- 8 m V000-21A-4 For details, refer to page --8. Component parts Plug MIL standard Number of terminals: 2 Cable: 2 cores x 0. mm 2 --41
Series 000 Exploded View/DIN Rail Manifold Type 4 Manifold r w U side r q e w (b) Lever e (a) Bolt (Both sides) Replacement Parts No. Description Part no. q Manifold block C4 000-0A-2- C assembly w e SUP/EXH block assembly End block assembly 000-1A-2 000-2A-2D r End block assembly 000-2A-2U Note C4: A, B port with One-touch fitting for ø4 C: A, B port with One-touch fitting for ø P/R port with One-touch fitting for ø8 For D side For U side DIN rail D side (a) Bolt (Both sides) How to Increase Manifold Base (1) Loosen (both) bolts (a), which are securing the manifold onto the DIN rail, 1 to 2 turns. (To remove the manifold base from the DIN rail, loosen the bolts 4 to turns.) (2) Press lever (b) to disconnect the manifold block assembly at the location in which you wish to place an additional manifold block assembly. (However, there are no levers between q and r or between w and r. They can be disconnected by merely pulling them apart.) Station expansion is possible at any position. Fig. (1) (a) Bolt (Both sides) () Mount additional manifold block assembly on the DIN rail as shown in the Fig. (2). (4) Press the block assemblies and tighten the bolts (a) to fix them to the DIN rail. Note) When there are 10 or fewer manifold block assemblies, and more are added to make a total of 11 or more, a supply/exhaust block assembly must also be added. Fig. (2) Hook this part onto the DIN rail, and press down in the direction of the arrow. (b) Lever --42
Port Solenoid Valve Base Mounted Series 000 Exploded View/DIN Rail Manifold Type 4F Manifold w e i t U side q y Location of addition Replacement Parts No. Description Part no. q Manifold block assembly 000-0A-1- Note C4: A, B port One-touch fitting for ø4 C: A, B port One-touch fitting for ø w SUP/EXH block assembly 000-1A-1D For D side, With D-sub connector and P/R port with One-touch fitting for ø8 e SUP/EXH block assembly 000-1A-1U For U side, With D-sub connector and P/R port with One-touch fitting for ø8 r End block assembly 000-2A-2D For D side, set with w t End block assembly 000-2A-1U For U side y End block assembly 000-2A-1D For D side u End block assembly 000-2A-2U For U side, set with e i SUP/EXH block assembly 000-1A-1M Without D-sub connector For indicated location C4 C (b) Lever w r DIN rail (a) Bolt (Both sides) D side (a) Bolt (Both sides) How to Increase Manifold Base (1) Loosen (both) bolts (a), which are securing the manifold onto the DIN rail, 1 to 2 turns. (To remove the manifold base from the DIN rail, loosen the bolts 4 to turns.) To add a manifold block assembly, add it to the U side so that the terminal number of the D-sub connector and the valve link position will be in accordance with the circuit diagram. Housing cover Fig. (2) Hook this part onto the DIN rail and press down until a click is heard. (2) Using a flat screwdriver, press lever (b) to disengage the link of the manifold block assembly on the U side or the D side from the SUP/EXH block assembly or from the end block assembly. (However, there are no levers between t and q. They can be disconnected by merely pulling them apart.) () Remove the housing cover from the D-sub connector portion of the SUP/EXH block assembly. (Refer to Fig. (1).) (4) Following the procedure shown in Fig. (2), mount the manifold block assembly to be added onto the DIN rail. As shown in Fig. (), insert the pin of the lead wire assembly into the D-sub connector, and attach the round crimped terminal to the screw that connects the wires. () Press the block assemblies and tighten the bolts (a) to fix them to the DIN rail. Note) When there are 10 or fewer manifold block assemblies, and more are added to make a total of 11 or more, a supply/exhaust block assembly must also be added. Fig. (1) Black White Lead wire ass'y Hook D-sub connector (b) Lever Connector terminal no. U side Pin After inserting the pin, lightly pull on the lead wire to verify the lock. Stations Housing side D side Fig. () How to insert lead ( ) is for the case of a wire assembly pin D-sub connector for both sides (FB type). 1 station (11 stations) 2 station (12 stations) station (1 stations) 4 station (14 stations) station (1 stations) station (1 stations) 7 station (17 stations) 8 station (18 stations) 9 station (19 stations) 10 station (20 stations) B side coil A side coil B side coil A side coil B side coil A side coil B side coil A side coil B side coil A side coil B side coil A side coil B side coil A side coil B side coil A side coil B side coil A side coil B side coil A side coil Terminal Lead no. wire color Black White Black White Black White Black White Black White Black White Black White Black White Black White Black White Red Red --4
Series 000 Type 40 Manifold: Bottom Ported V-40- Station 2-M Grommet (G), (H) (Mounting hole) -Rc 1/8 (1(P), /(R) port) (Non-locking) G: 00 mm H: 00 mm M x 0.8 (PE port) (4(A), 2(B) port) (mm) Stations 2 L1 8 74 L2 40 4 90 72 10 88 122 104 7 18 120 8 14 1 9 170 12 10 18 18 11 202 184 12 218 200 1 24 21 14 20 22 1 2 248 1 282 24 17 298 280 18 14 29 19 0 12 20 1 28 L plug connector (L) M plug connector (M) DIN terminal (D) Built-in speed controllers MAX. 10 Applicable cable O.D. ø. to ø7 MAX. 11 : With light/surge voltage suppressor --44
Port Solenoid Valve Base Mounted Series 000 Grommet (G), (H) Type 41 Manifold: Side Ported V-41- Station 1-M (Non-locking) M x 0.8 (PE port) With filter (Mounting hole) (1(P), /(R) port) G: 00 mm H: 00 mm (4(A), 2(B) port) (mm) Stations 2 L1 2 8 L2 4 9 4 84 7 100 91 11 107 7 12 12 8 148 19 9 14 1 10 180 171 11 19 187 12 212 20 1 228 219 14 244 2 1 20 21 1 27 27 17 292 28 18 08 299 19 24 1 20 40 1 L plug connector (L) M plug connector (M) DIN terminal (D) Built-in speed controllers MAX. 11 MAX. 10 Applicable cable O.D. ø. to ø7 : With light/surge voltage suppressor --4
Series 000 Type 42 Manifold: Side Ported V-42- Station 1-01 Grommet (G), (H) (Non-locking) M x 0.8 (PE port) (Mounting hole) 4-Rc 1/4 (1(P), /(R) port) G: 00 mm H: 00 mm 2n-Rc 1/8 (4(A), 2(B) port) 24. P=17 (mm) Stations 2 L1 8 L2 70 4 100 87 117 104 14 121 7 11 18 8 18 1 9 18 172 10 202 189 11 219 20 12 2 22 1 2 240 14 270 27 1 287 274 1 04 291 17 21 08 18 8 2 19 42 20 72 9 L plug connector (L) M plug connector (M) DIN terminal (D) Built-in speed controllers MAX. 11 MAX. 10 Applicable cable O.D. ø. to ø7 : With light/surge voltage suppressor --4
Port Solenoid Valve Base Mounted Series 000 Type 42 Manifold: Side Ported V-42- Station 1-C Grommet (G), (H) (Non-locking) M x 0.8 (PE port) MAX.. (One-touch fitting) (Mounting hole) 4-Rc 1/4 (1(P), /(R) port) G: 00 mm H: 00 mm 2n-One-touch fitting (4(A), 2(B) port) Applicable tubing model: T004 Stations 2 L1 81 L2 2 8 4 97 84 11 100 129 11 7 14 12 8 11 148 9 177 14 10 19 180 11 209 19 12 22 212 1 241 228 14 27 244 1 27 20 1 289 27 17 0 292 18 21 08 19 7 24 (mm) 20 40 L plug connector (L) M plug connector (M) DIN terminal (D) Built-in speed controllers MAX. 11 MAX. 10 Applicable cable O.D. ø. to ø7 : With light/surge voltage suppressor --47
Series 000 Type 4 Manifold: Side Ported Grommet (G), (H) V-4- Station 1-C4 (Non-locking) (PE port) (Mounting hole) G: 00 mm H: 00 mm 4-Rc 1/8 (1(P), /(R) port) Stations 2 L1 2 8 L2 4 9 2n-One-touch fitting (4(A), 2(B) port) Applicable tubing model: T042 4 84 7 100 91 11 107 7 12 12 8 148 19 9 14 1 10 180 171 11 19 187 12 212 20 1 228 219 14 244 2 1 20 21 1 27 27 17 292 28 18 08 299 19 24 1 (mm) 20 40 1 L plug connector (L) M plug connector (M) DIN terminal (D) Built-in speed controllers MAX. 11 MAX. 10 Applicable cable O.D. ø. to ø7 : With light/surge voltage suppressor --48
Port Solenoid Valve Base Mounted Series 000 Type 41P Flat Ribbon Cable Manifold: Side Ported V-41P- Station -M 2n-M x 0.8 (4(A), 2(B) port) (Light/Surge voltage suppressor) A side 4-Rc 1/8 (1(P), /(R) port) (Mounting hole) (Non-locking) Triangle mark (Station n) (Station 1) B side Connector polarity indicator Applicable connector: 2 pins MIL (Conforming to MIL-C-80) (mm) Built-in speed controllers Stations 4 L1 L2 77 2 94. 79. 112 97 129. 114. 7 147 12 8 14. 149. 9 182 17 10 199. 184. 11 217 202 12 24. 219. --49
Series 000 Type 4P Flat Ribbon Cable Manifold: Side Ported V-4P- Station -C4 2n-One-touch fitting (4(A), 2(B) port) Applicable tubing model: T042 (Light/Surge voltage suppressor) A side MAX. Triangle mark 4-Rc 1/8 (1(P), /(R) port) 2-ø. (Mounting hole) (Non-locking) B side (mm) Built-in speed controllers Stations 4 L1 L2 77 2 94. 79. 112 97 129. 114. 7 147 12 8 14. 149. 9 182 17 10 199. 184. 11 217 202 12 24. 219. MAX. 11 --0
Port Solenoid Valve Base Mounted Series 000 Grommet (G), (H) 2n-One-touch fitting (A, B port) Applicable tubing model C: T004 Stations L1 L2 L L4 U side 2 110. 100 88 11. DIN rail DIN rail holding screw 1. 12 104 1 4 148 17. 120 14 Type 4 DIN Rail Manifold (Non Plug-in): Side Ported V-4- Station D- C4C CC 10. 10 1 12. Manual override (Non-locking) (Rail mounting hole pitch 12.) (Station n) (Station 1) 18. 17 12 17 One-touch fitting port (P, R port) Applicable tubing model: T080 Separation lever (Push type) 7 198 187. 18 1 8 210. 200 184 1. D side 9 22 212. 200 11. (mm) 10 248 27. 21 1 C4 2n-One-touch fitting (A, B port) Applicable tubing model C4: T042 G: 00 H: 00 V-4- Station B- C4C CC (mm) Stations 2 4 7 8 9 10 L1 1. 148 10. 18. 198 210. 22 248 20. L2 12 17. 10 17 187. 200 212. 27. 20 L 104 120 1 12 18 184 200 21 22 L4 1 14 12. 17 1 1. 11. 1 14 (mm) Stations 11 12 1 14 1 1 17 18 19 20 L1 27 298 10. 2. 0. 7 8. 98 42 L2 22. 287. 00 12. 2 0 2. 7 87. 412. L 248 24 280 29 12 28 44 0 7 92 L4 12. 17 1. 1. 12 1. 14. 1 11 1. V-4- Station U- C4C CC L plug connector (L) M plug connector (M) MAX. 10 DIN terminal (D) Applicable cable O.D. ø. to ø7 : With light/surge voltage suppressor Stations L1 L2 L L4 2 110. 100 88 11. 1. 12 104 1 4 148 17. 120 14 10. 10 1 12. 7 18. 198 17 187. 12 18 17 1 8 210. 200 184 1. 9 22 212. 200 11. (mm) 10 248 27. 21 1 --1
Series 000 2n-One-touch fitting (A, B port) Applicable tubing model C: T004 Type 4F DIN Rail Manifold (Non Plug-in): Side Ported V-4FD- Station - C4C CC C4 2n-One-touch fitting (A, B port) Applicable tubing model C4: T042 One-touch fitting port (P, R port) Applicable tubing model: T080 U side D side DIN rail DIN rail holding screw Manual override (Non-locking) Terminal no. 1 JIS-X-101 Applicable connector D-SUB { MIL-C-2408} (Rail mounting hole pitch 12.) V-4FU- Station - C4C CC (Station n)(station 1) Separation lever (Push type) D side connector Stations L1 L2 L L4 2 110. 100 88 11. 1. 12 104 1 4 148 17. 120 14 10. 10 1 12. 18. 17 12 17 7 198 187. 18 1 8 210. 200 184 1. 9 22 212. 200 11. V-4F U C4C D- Station B- CC (2 to 10 stations) V-4FB- Station - C4C CC (11 to 20 stations) (mm) 10 248 27. 21 1 Stations L1 L2 L L4 2 110. 100 88 11. 1. 12 104 1 4 148 17. 120 14 10. 10 1 12. 18. 17 12 17 7 198 187. 18 1 8 210. 200 184 1. 9 22 212. 200 11. (mm) 10 248 27. 21 1 Stations L1 L2 L L4 Stations L1 L2 L L4 2 1. 12 104 1 11 27 22. 248 12. 148 17. 120 14 12 298 287. 24 17 4 10. 10 1 12. 1 10. 00 280 1. 18. 17 12 17 14 2 12. 29 1. 198 187. 18 1 1. 2 12 12 7 210. 200 184 1. 1 0. 0 28 1. 8 22 212. 200 11. 17 7 2. 44 14. 9 248 27. 21 1 18 8. 7 0 1 (mm) 10 20. 20 22 14 19 98 87. 7 11 (mm) 20 42 412. 92 1. --2
Series Made to Order Specifications: Please contact SMC for detailed specifications, dimensions, and delivery. 1. Solenoid Valve: External Pilot Specifications Applicable solenoid valve series 000/000 (Non plug-in type only) Model no. 0 ( ) X20 Specifications Entry is the same as standard products. Operating pressure Main pressure range (MPa) External pilot pressure Pilot exhaust method Dimensions 000: 8 mm longer 000: 8 mm longer 100 kpa to 0.7 0.1 to 0.7 Pilot valve individual exhaust JIS Symbol Body ported 2 position single position closed center 2 position double position exhaust center position pressure center --8
Series Made to Order Specifications: Please contact SMC for detailed specifications, dimensions, and delivery. 2. Solenoid Valve: Special Manual Override. Solenoid Valve: Opposite Mount of Solenoid Assembly Applicable solenoid valve series 000 (Non plug-in type only) Model no. Applicable solenoid valve series 1000/000/000 (Non plug-in type only) Model no. A ( ) ( ) X1 1 Dimensions: Single Push type A Entry is the same as standard products. A E Push type A Push-locking type E Entry is the same as standard products. Dimensions: 1120- G-M-X1 (Push type A) (Non-locking) (Mounting hole for manifold) Push-locking type E (Piping port) (Push-locking type E) ( ) Pressing makes the valve operate. The valve can be locked in the manual override position by turning it to the direction that the arrow shows while keeping it pressed. If it is not turned, it can be used as a non-locking push type. Caution When operating the lock with the driver, use a watchmakers screwdriver and turn lightly. (Torque: 0.1 N m or less) Note) Because the manual override unit protrudes, the manual override could activate unintentionally if the protrusion is touched or an object falls on it. Therefore, take the proper preventative measures. --8
Series Made to Order Specifications: Please contact SMC for detailed specifications, dimensions, and delivery. 4. Manifold: Common SUP/Individual EXH Type Applicable solenoid valve series 000 Common SUP/Individual EXH type V-21- Specification Common SUP/Individual EXH type 1(P) port Rc /(R) port M x 0.8 4(A), 2(B) port Valve Dimensions: Grommet Type Model no. 1 8 V 21 0 Stations 02 2 stations 20 stations Applicable solenoid valve G 2 - L M M - C4 D C Applicable blanking plate assembly DXT192-1-1A Applicable throttle valve DXT14-4-1A Applicable silencer AN120-M Note) Refer to page --2 for manifold option. Note) To use the 2 with a throttle valve mounted on it, open the throttle valve one turn or more from the fully closed position. 20 (Non-locking) P port thread type Nil Rc 00F G 00N NPT 00T NPTF M x 0.8 (PE port) 4-ø4. Mounting hole (4(A), 2(B) port) 2-Rc 1/8 (1(P) port) Stations 2 L1 0 L2 40 4 82 72 98 88 ((R1), (R2) port) 114 104 7 10 120 8 14 1 9 12 12 10 178 18 11 194 184 12 210 200 1 22 21 14 242 22 1 28 248 1 274 24 17 290 280 18 0 29 19 22 12 (mm) 20 8 28 --87