KIT 7852 9 decal placement 8578520 0200 corporal missile 25 20 12 19 20 23 8 with transporter and launcher The U.S. Army surface to surface Corporal Missile was capable of launching a conventional or Atomic missile at ranges over 75 miles with great accuracy enabling a distant attack. The missile is carried by a large specially designed transporter which travels to the launching site and erects the missile on to a launching platform. Your Revell model features transporter cab doors that open and close, operating pistons on leg braces, real gears elevate the rotary boom, leg pads hinge and swivel, 4 movable support arms and braces, six figures, a radar scanner and launcher platform with optional traveling or launch position assemblies and authentic U.S. Army missile and vehicle decal markings. 13 20 9 20 10 * REPEAT SEVERAL TIMES * A REPETER PLUSIEURS FOIS ` ` ` ` * REPETEZ LE PROCEDE * DECAL * DECAL COMANIE 4 (Other side 3) 1 (Other side 2) 21 7 20 11 Read this BeFORe YOU BeGIn * Study the assembly drawings. * Each plastic part is identified by a number. * In the assembly drawings, some parts will be marked by a star ( ) to indicate chrome plated plastic. * For better paint and decal adhesion, wash the plastic parts in a mild detergent solution. Rinse and let air dry. * Check the fit of each piece before cementing in place. * Use only cement for polystyrene plastic. * Scrape plating and paint from areas to be cemented. * Allow paint to dry thoroughly before handling parts. * Any unused parts may be discarded. 14 24 5 6 1. 2. 3. 4. 5. 6. 7. 8. 9. 18 Cut desired decal from sheet. Dip decal in water for a few seconds. Place wet decal on paper towel. Wait until decal is movable on paper backing. Place decal in position on model, face up and slide backing away. Press out air bubbles with a soft damp cloth. Milkiness that may appear is for better decal adhesion and will dry clear. Wipe away any excess adhesive. Do not touch decal until fully dry. Allow the decals 48 hours to dry before applying clear coat. 22 16 15 18 note: decals are compatible with setting solutions or solvents. * ASSEMBLY CAUTION ` *ATTENTION D` ASSEMBLEE * CEMENT TOGETHER * A COLLER lire ce QUI SUIt avant de commencer * Etudier les schémas de montage. * Chaque pièce en plastique est identifiée par un numéro. * Sur les schémas de montage, certaines pièces sont marquées d'une étoile ( ) pour indiquer qu'elles sont en plastique chromé. * Pour une meilleure prise de la peinture et des autocollants, laver les pièces en plastique avec une solution détergente peu concentrée. Les rincer et les laisser sécher à l'air. * Vérifier que chaque pièce s'ajuste bien avant de la coller en place. * N'utiliser que de la colle pour polystyrène. * Gratter les parties à coller pour enlever le chrome et la peinture. * Laisser la peinture bien sécher avant de manipuler les pièces. * Toute pièce inutilisée peut être jetée. directives d'application des autocollants decal application InStRUctIOnS 15 17 * REPEAT PROCEDURE 1. 2. 3. 4. 5. 6. 7. 8. 9. Découper l'autocollant désiré de la feuille. Tremper l'autocollant dans de l'eau pendant quelques secondes. Placer l'autocollant mouillé sur une serviette en papier. Attendez que l'autocollant puisse être déplacé sur son support en papier. Mettre l'autocollant en position sur le modèle face sur le dessus et faire glisser le support pour l'enlever. Appuyer avec un chiffon doux humide pour éliminer les bulles d'air. La substance laiteuse qui peut apparaître est destinée à améliorer l'adhésion de l'autocollant et devient incolore au séchage. Essuyer pour enlever tout excédent d'adhésif. Ne pas toucher l'autocollant tant qu'il n'est pas bien sec. Laisser l'autocollant sécher pendant 48 heures avant d'appliquer une couche transparente. RemaRQUe: les autocollants sont compatibles avec les solutions de fixage ou les solvants. * REMOVE AND THROW AWAY * A RETIRER ET JETER * DO NOT CEMENT * NE PAS COLLER this paint guide is provided to complete this kit as shown on the box. Ce guide de peintures est fourni pour reproduire le modèle réduit qui apparaît sur la boîte. Semi Gloss Black Noir satiné Flat Black Noir mat Gloss Red Rouge brilliant Flat White Blanc mat Aluminum Aluminum Steel Acier Olive Drab Gris vert Tan Tan Dark Brown Brun foncé Flesh Chair If you have any questions or comments, call our hotline at: (800) 833-3570 or, please write to: Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007 Be sure to include the plan number (85785200200), part number, description, your return address and phone number. Visit our website: www.revell.com Kit 7852 - Page 16 Revell Inc. Northbrook, IL. Copyright 2010. All rights reserved.
1 missile ASSEMBLY 5 MISSILE REAR FLAT WHITE 7 MISSILE FIN SEMI GLOSS 3 NOSE CONE GLOSS RED 1 MISSILE FRONT FLAT WHITE 6 MISSILE REAR FLAT WHITE 8 TAIL CAP FLAT WHITE N WHITE W 2 2 MISSILE FRONT FLAT WHITE 4 CONNECTOR RING FLAT WHITE WHITE launcher ASSEMBLY E WHITE fin painting end view S 7 MISSILE FIN SEMI GLOSS 22 MISSILE SUPPORT FLASH SHIELD 23 LAUNCHER FRAME 21 MISSILE SUPPORT FLASH SHIELD 25 LAUNCHER BLAST SHIELD 19 PLATFORM SUPPORT FLASH SHIELD 20 PLATFORM SUPPORT FLASH SHIELD 24 LAUNCHER FRAME Kit 7852 - Page 2
2 launcher assembly continued 11 JACK ARM 13 JACK ARM 14 JACK ARM 12 JACK ARM 17 LAUNCHER TOW BAR SUPPORT STEEL 9 JACK ARM 15 JACK ARM 18 LAUNCHER TOW BAR STEEL 10 JACK ARM 16 JACK ARM 28 MISSILE ARMS 26 LAUNCHER PLATFORM 27 MISSILE ARM HINGE OLIVE DRAB 27 MISSILE ARM HINGES 28 MISSILE ARMS GLOSS RED 26 LAUNCHER PLATFORM 27 MISSILE ARM HINGE Kit 7852 - Page 3
2 launcher ASSEMBLy FINAL 31 TIRE 30 AXLE 29 WHEEL traveling position 34 ARM CAP 35 ARM CAP SCREW 33 JACK DISCS SWING CLOSE SWING CLOSE AND HOOK launching position 33 JACK DISCS completed MISSILE AND LAUNCHER PINS ON LAUNCHER FIS INTO HOLES ON ROCKET 33 JACK DISC 33 JACK DISC 32 CENTER JACK STEEL Kit 7852 - Page 4 33 JACK DISC 32 CENTER JACK STEEL 33 JACK DISC
3 cab assembly 45 FUEL TANK 44 STEERING MOTOR 49 SEAT FLAT 49 SEAT 46 FRONT CAB BASE CUT OUT WINDOW GUIDE ALONG DOTTED LINES. ATTACH TO CLEAR PLASTIC SHEET AND CUT ALONG SOLID GUIDE LINES. SNAP WIN- DOWS INTO OPENINGS AS SHOWN. 47 CAB INBOARD SIDE 48 CAB INBOARD SIDE A B 50 STEERING HANDLE SEMI GLOSS 52 CAB FRONT D C 53 CAB FRONT 51 CONTROL PANEL FLAT Kit 7852 - Page 5
3 CAB ASSEMBLY CONTINUED 58 CAB BACK E F 59 CAB BACK 57 INTERCONNECTING BOX 56 INTERCONNECTING BOX 55 DRIVER'S ASSISTANT FACE, HANDS () SHOES () HELMET () 54 DRIVER FACE, HANDS () SHOES () HELMET () 66 HEADLIGHTS 65 HEADLIGHTS 60 AIR CLEANER GLOSS RED FLAT WHITE WHITE GLOSS RED Kit 7852 - Page 6
3 cab ASSEMBLY CONTINUED 61 MUFFLER HALF 63 AUXILIARY FUEL TANK 62 MUFFLER HALF 101 CAB BASE SUPPORT 64 AUXILIARY FUEL TANK 70 CAB OUTBOARD SIDE I J 67 CAB DOOR H G 69 CAB DOOR 68 CAB OUTBOARD SIDE Kit 7852 - Page 7
3 OUTER SIDES TO BODY CAB ASSEMBLY FINAL 72 CANVAS 73 CANVAS 4 74 CHASSIS HALF chassis ASSEMBLY 44 STEERING MOTOR FLAT 71 FRONT END PANEL 83 REAR HINGE PLATE 75 CHASSIS HALF 82 STEERING RACK MOTOR PLATE 76 FRONT HINGE PLATE 77 STEERING RACK 77 STEERING RACK Kit 7852 - Page 8
4 chassis assembly continued 79 FRONT MOTOR HALF 78 FRONT MOTOR HALF 84 REAR MOTOR 85 REAR MOTOR 81 FRONT MOTOR 86 REAR MOTOR 80 FRONT MOTOR 87 REAR MOTOR 90 STEERING LINKAGE 88 STEERING BAR 90 STEERING LINKAGE 89 UNIVERSAL JOINT 94 BOOM REST 93 TOOL BOX SEMI GLOSS 92 TOOL BOXES 95 HINGE PLATE CAP 91 FIRE EXTINGUISHER GLOSS RED Kit 7852 - Page 9
4 chassis ASSEMBLY continued 104 TIRE OUTSIDE HALF FLAT 102 SPARE TIRE HOLDER 103 TIRE INSIDE HALF FLAT 100 REAR BASE BRACE 96 POWER BASE 99 REAR BASE BRACE 98 FRONT BASE BRACE 97 FRONT BASE BRACE 107 ARCH 105 CROSS BRACE BOX LID 112 FENDER TAB SLOT 106 CROSS BRACE 108 ARCH 111 FENDER Kit 7852 - Page 10
4 chassis assembly final 109 ELEVATING GEAR 110 ELEVATING GEAR 113 JACK CYLINDER CAP 114 JACK CYLINDER 115 JACK PISTON 116 JACK PAD STEEL 5 elevating boom assembly 118 ELEVATING BOOM SUPPORT 117 ELEVATING BOOM RACK 119 ELEVATING BOOM STIFFENERS 121 REAR ELEVATING SLIDE 120 FRONT ELEVATING SLIDE 119 ELEVATING BOOM STIFFENERS Kit 7852 - Page 11
5 elevating boom ASSEMBLY continued 126 MISSILE HOLDER 127 MISSILE HOLDER 123 REAR HOUSING CLAMP 124 WINCH MOTOR 122 FRONT HOUSING CLAMP 125 WINCH MOTOR 130 FRONT CLAMP HALF 129 FRONT CLAMP 131 FRONT CLAMP 135 REAR JAW CLAMP 136 REAR CLAMP HALF 128 FRONT CLAMP HALF 134 REAR CLAMP 132 FRONT CLAMP HOUSING PLATE 138 REAR CLAMP HOUSING PLATE 133 REAR CLAMP HALF 137 REAR CLAMP Kit 7852 - Page 12
5 evevating boom assembly continued 139 ELEVATING PINION GEAR 147 BOOM PLATFORM 142 BOOM DRIVE MOTOR 140 ELEVATING BOOM HALF 141 ELEVATING BOOM DRIVE GEAR 143 BOOM DRIVE MOTOR 146 BOOM CROSS BRACE 144 BOOM GEAR SHAFT 149 ELEVATING BOOM HALF 145 BOOM GEAR SHAFT 148 BOOM PLATFORM 150 ELEVATING PINION GEAR SLIDE boom support to boom rails Kit 7852 - Page 13
5 151 LADDER elevating boom ASSEMBLY final 152 LADDER 153 BOOM RACK MOTOR 6 missile to boom final ASSEMBLY A 154 BOOM CENTER BRACE HOLES IN BOOMS (both sides) ELEVATING GEARS 155 SIDE VIEW MIRROR 156 SIDE VIEW MIRROR AS SHOWN IN DRAWING (A) ABOVE. HOLD THE ELEVATING BOOM IN A VERTICAL POSITION. LINE UP GEARS AND SNAP, (DO NOT CEMENT), TO LOCATING PINS ON AND ELEVATING GEARS. THEN ROLL FORWARD TO DOWN POSITION. Kit 7852 - Page 14
7 BROWN 40 RADAR OPERATOR OLIVE DRAB figure assembly DECAL 14 38 RADAR ANTENNA OLIVE DRAB TAN 36 RADAR OPERATOR SEAT 37 RADAR SET 39 RADAR SCREEN 157 STANDING FIGURE OLIVE DRAB 41 GROUCHING FIGURE 42 STANDING FIGURE OLIVE DRAB TAN OLIVE DRAB TAN DARK BROWN DARK BROWN DARK BROWN DARK BROWN TAN 158 BASE FLAT 43 BASE FLAT 43 BASE FLAT 8 completed KIT assembly Kit 7852 - Page 15
KIT 7852 9 corporal missile decal placement 25 20 12 19 20 23 8 with transporter and launcher The U.S. Army surface to surface Corporal Missile was capable of launching a conventional or Atomic missile at ranges over 75 miles with great accuracy enabling a distant attack. The missile is carried by a large specially designed transporter which travels to the launching site and erects the missile on to a launching platform. Your Revell model features transporter cab doors that open and close, operating pistons on leg braces, real gears elevate the rotary boom, leg pads hinge and swivel, 4 movable support arms and braces, six figures, a radar scanner and launcher platform with optional traveling or launch position assemblies and authentic U.S. Army missile and vehicle decal markings. 9 20 10 * REPEAT SEVERAL TIMES * A REPETER PLUSIEURS FOIS ` ` ` ` * REPETEZ LE PROCEDE * DECAL * DECAL COMANIE 4 (Other side 3) 1 (Other side 2) 21 7 20 11 13 20 * Study the assembly drawings. * Each plastic part is identified by a number. * In the assembly drawings, some parts will be marked by a star ( ) to indicate chrome plated plastic. * For better paint and decal adhesion, wash the plastic parts in a mild detergent solution. Rinse and let air dry. * Check the fit of each piece before cementing in place. * Use only cement for polystyrene plastic. * Scrape plating and paint from areas to be cemented. * Allow paint to dry thoroughly before handling parts. * Any unused parts may be discarded. 24 5 6 6. 7. 18 15 8. 9. Cut desired decal from sheet. Dip decal in water for a few seconds. Place wet decal on paper towel. Wait until decal is movable on paper backing. Place decal in position on model, face up and slide backing away. Press out air bubbles with a soft damp cloth. Milkiness that may appear is for better decal adhesion and will dry clear. Wipe away any excess adhesive. Do not touch decal until fully dry. Allow the decals 48 hours to dry before applying clear coat. 22 18 16 15 * CEMENT TOGETHER * A COLLER * REMOVE AND THROW AWAY * A RETIRER ET JETER * DO NOT CEMENT * NE PAS COLLER this paint guide is provided to complete this kit as shown on the box. * Etudier les schémas de montage. * Chaque pièce en plastique est identifiée par un numéro. * Sur les schémas de montage, certaines pièces sont marquées d'une étoile ( ) pour indiquer qu'elles sont en plastique chromé. * Pour une meilleure prise de la peinture et des autocollants, laver les pièces en plastique avec une solution détergente peu concentrée. Les rincer et les laisser sécher à l'air. * Vérifier que chaque pièce s'ajuste bien avant de la coller en place. * N'utiliser que de la colle pour polystyrène. * Gratter les parties à coller pour enlever le chrome et la peinture. * Laisser la peinture bien sécher avant de manipuler les pièces. * Toute pièce inutilisée peut être jetée. Ce guide de peintures est fourni pour reproduire le modèle réduit qui apparaît sur la boîte. directives d'application des autocollants decal application InStRUctIOnS 1. 2. 3. 4. 5. * ASSEMBLY CAUTION ` *ATTENTION D` ASSEMBLEE lire ce QUI SUIt avant de commencer Read this BeFORe YOU BeGIn 14 17 * REPEAT PROCEDURE note: decals are compatible with setting solutions or solvents. Kit 7852 - Page 16 8578520 0200 1. 2. 3. 4. 5. 6. 7. 8. 9. Découper l'autocollant désiré de la feuille. Tremper l'autocollant dans de l'eau pendant quelques secondes. Placer l'autocollant mouillé sur une serviette en papier. Attendez que l'autocollant puisse être déplacé sur son support en papier. Mettre l'autocollant en position sur le modèle face sur le dessus et faire glisser le support pour l'enlever. Appuyer avec un chiffon doux humide pour éliminer les bulles d'air. La substance laiteuse qui peut apparaître est destinée à améliorer l'adhésion de l'autocollant et devient incolore au séchage. Essuyer pour enlever tout excédent d'adhésif. Ne pas toucher l'autocollant tant qu'il n'est pas bien sec. Laisser l'autocollant sécher pendant 48 heures avant d'appliquer une couche transparente. RemaRQUe: les autocollants sont compatibles avec les solutions de fixage ou les solvants. Semi Gloss Black Noir satiné Flat Black Noir mat Gloss Red Rouge brilliant Flat White Blanc mat Aluminum Aluminum Steel Acier Olive Drab Gris vert Tan Tan Dark Brown Brun foncé Flesh Chair If you have any questions or comments, call our hotline at: (800) 833-3570 or, please write to: Revell Inc Consumer Service Department, 1850 Howard Street Unit A, Elk Grove Village, Illinois 60007 Be sure to include the plan number (85785200200), part number, description, your return address and phone number. Visit our website: www.revell.com Revell Inc. Northbrook, IL. Copyright 2010. All rights reserved.