INSTALL GUIDE DOCUMENT NUMBER 090 REVISION DATE 7070 FIRMWARE IDL-HA(RS)-HA7-[ADS-HA7] HARDWARE ADS-HA7 ACCESSORIES ADS-USB (REQUIRED) COMPATIBLE RF-KIT (REQUIRED) DIRECTED SMARTSTART & ADS-HRN(RS)-SM (OPTIONAL) NOTICE The manufacturer will accept no responsability for any electrical damage resulting from improper installation of this product, be that either damage to the vehicle itself or to the installed device. This device must be installed by a certified technician. Please review the Installation Guide carefully before beginning any work. Automotive Data Solutions Inc. 7 BEFORE INSTALLATION - Connect module to computer - Login to Weblink account - Flash firmware to module (module is not preloaded with firmware) - Use accessories accordingly (accessories are sold separately)
PAGE OF 8 DOC.: #090 7070 VEHICLE LIST - OF RLX PTS AT -7 TLX PTS AT -7 Fit PTS AT -7 HR-V PTS AT -7 Odyssey PTS AT -7 Pilot PTS AT -7 Ridgeline PTS AT 7 BRAKE PEDAL STATUS TACHOMETER OUTPUT -7 AUTOLIGHT CTRL -7 RDX PTS AT HOOD STATUS OUTPUT* MDX PTS AT TRUNK STATUS OUTPUT DOOR STATUS OUTPUT DOOR UNLOCK TRUNK/HATCH RELEASE DOOR LOCK E-BRAKE OUTPUT DISARM OEM ALARM POWER SLIDING DOOR (R) ARM OEM ALARM POWER SLIDING DOOR (L) DATA IMMOBILIZER BYPASS -7 POWER LIFTGATE YEAR ILX PTS AT INSTALL TYPE MODEL HONDA ACURA MAKE FEATURES *Available only if vehicle is equipped with factory hood switch. Automotive Data Solutions Inc. 7
PAGE OF 8 DOC.: #090 7070 BOX CONTENTS - OF BOX CONTENTS MODULE 0 PIN CONNECTOR T-HARNESS VS LED BLUE BLACK BLACK 8 0 8 0 7 9 7 9 8 0 7 9 PROGRAMMING BUTTON LED A VS G F B E BLACK RF PORT/ WEBLINK PORT BLUE TELEMATIC PORT BLACK PIN CONNECTOR MS VS VS AFTERMARKET HOOD SWITCH AND CABLE C D 9 0 7 8 WHITE WARNING STICKER WEBLINK CABLE (required accessory sold separately) WEBLINK CABLE MODULE WEBLINK PORT COMPUTER USB PORT PIN BLACK CABLE Automotive Data Solutions Inc. 7
PAGE OF 8 DOC.: #090 7070 COMPATIBLE ACCESSORIES - OF RF KIT (accessories sold separately) RF KIT MODULE RF PORT ANTENNA TELEMATIC KIT (accessories sold separately) ADS-HRN(RS)-SM DIRECTED SMARTSTART (NC) MODULE TELEMATIC PORT (NC) (NC) Automotive Data Solutions Inc. 7
PAGE OF 8 DOC.: #090 7070 ACURA RDX PTS AT RLX PTS AT TLX PTS AT Fit PTS AT -7-7 -7-7 -7 HONDA HR-V PTS AT Pilot PTS AT Ridgeline PTS AT -7 7 Automotive Data Solutions Inc. 7 CONNECTOR COLOR CONNECTOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR -7 CONNECTOR NAME ILX PTS AT -7 WIRE DESCRIPTION MDX PTS AT YEAR MODEL MAKE TYPE - WIRE CHART - OF pin PTS harness pin Smart PCU, above glove box 0 pin harness 0 pin Smart PCU, above glove box Pink 08 Gray pin PTS harness pin Smart PCU, above gas pedal 0 pin harness 0 pin Smart PCU, above gas pedal Orange 08 Gray pin PTS harness pin Smart PCU, above gas pedal 0 pin harness 0 pin Smart PCU, above gas pedal Tan 08 Gray pin PTS harness pin Smart PCU, near driver fuse box 0 pin harness 0 pin Smart PCU, near driver fuse box Red 08 Pink pin PTS harness pin Smart PCU, above glove box 0 pin harness 0 pin Smart PCU, above glove box Red 08 Pink pin PTS harness pin Smart PCU, behind instrument cluster 0 pin harness 0 pin Smart PCU, behind instrument cluster Brown 08 Gray pin PTS harness pin Smart PCU, behind instrument cluster 0 pin harness 0 pin Smart PCU, behind instrument cluster Brown 08 Gray pin PTS harness pin Smart PCU, above glove box 0 pin harness 0 pin Smart PCU, above glove box Pink 08 White pin PTS harness pin Smart PCU, above glove box 0 pin harness 0 pin Smart PCU, above glove box Pink 08 White
PAGE OF 8 DOC.: #090 7070 TYPE - WIRING DIAGRAM - OF MODULE SMART PCU (USE WIE CHART) VS A G RF PORT/WEBLINK PORT B F TELEMATIC PORT PIN PTS CONNECTOR E C VS D PIN PTS HARNESS A ***WITH T-HARNESS MANUFACTURED AFTER /0/7*** VS MS 0 PIN CONNECTOR VS B 0 PIN HARNESS HEAD LAMP SWITCH 8 0 8 0 7 9 7 9 C 8 7 0 9 MS LIGHTS - PARKING LIGHT - 08 BROWN/BLACK - PARKING LIGHT OUTPUT GRAY - GWR OUTPUT 0 EMPTY 0 EMPTY 0 EMPTY 0 PURPLE/GREEN (NC) 07 EMPTY 08 BLUE/GREEN (NC) 09 EMPTY 0 EMPTY GRAY/GREEN - HORN OUTPUT DKGREEN/GREEN (NC) OPTIONAL 0 9 8 7 HORN D 8 0 7 9 0 GRAY/BLACK (NC) 0 GRAY/WHITE - HOOD STATUS INPUT WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH AFTERMARKET HOOD SWITCH KEYLESS ACCESS SYSTEM FUNCTIONALITY OF THE VEHICLE'S DOOR HANDLE WILL NOT REMAIN OPERATIONAL DURING REMOTE START SEQUENCE. Automotive Data Solutions Inc. 7
PAGE 7 OF 8 DOC.: #090 7070 Automotive Data Solutions Inc. 7 CONNECTOR COLOR CONNECTOR TYPE POSITION WIRE COLOR POLARITY MODULE LOCATION COMPONENT LOCATOR -7 CONNECTOR NAME YEAR MODEL Odyssey PTS AT WIRE DESCRIPTION HONDA MAKE TYPE - WIRE CHART - OF pin PTS harness pin Smart PCU, above gas pedal 0 pin harness 0 pin Smart PCU, above gas pedal 0 Pink 08 Gray
PAGE 8 OF 8 DOC.: #090 7070 TYPE - WIRING DIAGRAM - OF MODULE SMART PCU (USE WIE CHART) VS A G RF PORT/WEBLINK PORT B F TELEMATIC PORT PIN PTS CONNECTOR E C VS D PIN PTS HARNESS A ***WITH T-HARNESS MANUFACTURED AFTER /0/7*** VS MS 0 PIN CONNECTOR VS B 0 PIN HARNESS HEAD LAMP SWITCH 8 0 8 0 7 9 7 9 C 8 7 0 9 PARKING LIGHT - 08 LIGHTS - 0 MS BROWN/BLACK - PARKING LIGHT OUTPUT GRAY - GWR OUTPUT 0 EMPTY 0 EMPTY 0 EMPTY 0 PURPLE/GREEN (NC) 07 EMPTY 08 BLUE/GREEN (NC) 09 EMPTY 0 EMPTY GRAY/GREEN - HORN OUTPUT DKGREEN/GREEN (NC) OPTIONAL 0 9 8 7 HORN D 8 0 7 9 0 GRAY/BLACK (NC) 0 GRAY/WHITE - HOOD STATUS INPUT WITHOUT OEM HOOD SWITCH: INSTALL AND CONNECT TO AFTERMARKET HOOD SWITCH AFTERMARKET HOOD SWITCH KEYLESS ACCESS SYSTEM FUNCTIONALITY OF THE VEHICLE'S DOOR HANDLE WILL NOT REMAIN OPERATIONAL DURING REMOTE START SEQUENCE. Automotive Data Solutions Inc. 7
MODULE PROGRAMMING PROCEDURE (PTS) - OF Push start button once [x] to ON position. STOP ACC ON START 07 ENGINE START STOP 0 STOP ACC PAGE 9 OF 8 DOC.: #090 7070 Push start button once [x] to ON position. STOP ACC ON START ENGINE START STOP Wait, LED will flash GREEN rapidly. 08 Push start button once [x] to position. 09 ON START ENGINE START STOP Wait, LED will turn solid GREEN for seconds. Push start button once [x] to position. STOP ACC ON START ENGINE START STOP 0 WARNING: Disconnect power last. Disconnect module from vehicle. 0 Press UNLOCK on the OEM remote. 0 Connect module to computer and proceed with extended programming. If the vehicle is equipped with a power liftgate: Open and close the power liftgate with the OEM keyfob. 0 Connect power first. Connect module to vehicle. Module Programming Procedure completed. Automotive Data Solutions Inc. 7
VALET MODE PROGRAMMING PROCEDURE - OF NOTE: In Valet Mode, the Remote starter is not functional. Keyless entry, Lock and Unlock will remain functional. See RF kit user manual for alternate valet mode programming. Time restriction. Complete next step within 7 seconds. ACC ON START PAGE 0 OF 8 DOC.: #090 7070 To exit valet mode: repeat steps to. Cycle ignition ON five times [x /ON] rapidly. ENGINE START STOP 0 0 Wait, LED will turn solid RED for seconds. Set ignition to position. ACC ON START ENGINE START STOP 0 Valet Mode Programming Procedure completed. Automotive Data Solutions Inc. 7
AFTERMARKET REMOTE PROGRAMMING PROCEDURE - OF WARNING: Program aftermarket remotes before usage. A maximum of four [x] aftermarket remotes per system. 0 LED will flash GREEN once [x]. Time restriction. Complete next step within 7 seconds. 07 LED will turn solid RED. Cycle ignition ON five times [x /ON] rapidly. To program additional remotes: repeat steps to 7 using each additional remote. 0 LED will turn solid RED. 08 Wait, LED will turn. 0 Time restriction. Complete next step within seconds from previous step. 09 ACC ON START PAGE OF 8 DOC.: #090 7070 ENGINE START STOP Set ignition to position. ACC ON START ENGINE START STOP 0 Press once [x] on LOCK button of aftermarket remote. Automotive Data Solutions Inc. 7 0 Aftermarket Remote Programming Procedure completed.
PAGE OF 8 DOC.: #090 7070 MODULE NAVIGATION PROCEDURE - OF It is mandatory to exit the Module Navigation at the end of this procedure. Failure to exit the Module Navigation will drain vehicle battery. To exit the Module Navigation at any time: Follow STEP. 0 Module must be programmed to the vehicle. 0 Use the Module Navigation Chart on the next page. 0 Set ignition to position. 07 TO ACCESS THE MENUS: Press and hold programming button until LED turns solid GREEN. 08 IN THE MENUS: Press the programming button as many times as the menu number indicates. LED will flash GREEN an equal amount of times continuously. 09 ACC ON START TO ACCESS THE OPTIONS: Press and hold programming button until LED turns solid RED. 0 IN THE OPTIONS: Press the programming button as many times as the option number indicates. LED will flash RED an equal amount of times continuously. TO ACCESS THE SETTINGS: Press and hold programming button until LED turns solid GREEN. Configure every other setting and proceed to step. [Z] LED will flash GREEN as many times as the current (or default) setting number, continuously. MANDATORY: EXIT MODULE NAVIGATION. Press and hold programming button for 7 seconds. LED will flash RED rapidly. Release programming button. LED will turn. [Z] IN THE SETTINGS: Press the programming button as many times as necessary to access your setting. LED will flash GREEN an equal amount of times continuously. Module navigation completed. To return to the MENUS: exit the Module Navigation and redo the Module Navigation Procedure. Failure to exit the Module Navigation will drain vehicle battery. [Y] To save and return to the OPTIONS: Press and hold programming button until LED turns solid RED. [Y] LED will flash RED as many times as the current option number continuously. ENGINE START STOP 0 [X] Automotive Data Solutions Inc. 7
PAGE OF 8 DOC.: #090 7070 [Y] OPTIONS [X] MENUS MODULE NAVIGATION CHART: NOTES I Default settings are listed in bold. II Make sure the option is covered on the vehicle before attempting to change the setting. 0 0 DISARM/UNLOCK BEFORE START RELOCK AFTER START RELOCK AFTER SHUTDOWN FORCE UNLOCK ALL ON FIRST PRESS 0 TAKEOVER 0 07 [Z] SETTINGS MODULE NAVIGATION CHART - OF FACTORY KEYLESS RS SEQUENCE CONFIGURATION 08 09 MODULE RUN TIME WAIT TO START DELAY ON ON ON ON ENABLE DISABLE* DISABLE 0 LOCK + UNLOCK + LOCK 0 LOCK + LOCK + LOCK 0 MIN 0 MIN 0 0 MIN 0 MIN 0 MIN 0 0 MIN 07 MIN 08 MIN SEC 0 SEC 0 08 SEC 0 0 SEC 0 SEC 0 0 SEC 07 SEC 08 0 SEC 0 *Vehicle will shutdown when a door is opened. Automotive Data Solutions Inc. 7
PAGE OF 8 DOC.: #090 7070 [Y] OPTIONS [X] MENUS MODULE NAVIGATION CHART: NOTES [Z] SETTINGS MODULE NAVIGATION CHART - OF HORN EVENT TRIGGER CONFIGURATION -07 Technical Support only HORN CHIRPS WIDTH DOUBLE LOCK LOCK + UNLOCK 0 LOCK + UNLOCK + START 0 DOUBLE LOCK + START 0 msec msec 0 0 msec *Vehicle will shutdown when a door is opened. Automotive Data Solutions Inc. 7
[X] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC REMOTE STARTER ERROR CODES - OF I WARNING: The following applies only when the parking lights are connected and supported by the system. Engine running. Key in ignition at ON position. II After a remote starter failure, the parking lights will flash three [x] times, then will flash [X] number times to indicate an error code. See table. 0 0 Trunk is open. 0 Foot brake is ON. 0 Hood is open. 07 08 Tach failure. 09 0 System is in Valet Mode. CAN communication failure RS not synchronized. Start vehicle with OEM key for sec before trying a new RS sequence. [Y] NUMBER OF PARKING LIGHT FLASHES DIAGNOSTIC REMOTE STARTER ERROR CODES: NOTES I WARNING: The following applies only when the parking lights are connected and supported by the system. Engine tach signal is lost. II If the engine shuts down after a remote starter sequence: Press and hold the Trunk button and the Start button at the same time for. seconds when using a -WAY remote. OR Press once [x] on button when using a -WAY remote. 0 Foot brake is ON. 0 Hood is open. 0 Engine RPM limiter is ON. 0 Glow plug timeout error. 07 Vehicle is moving (VSS). 08 Check engine warning light is ON. 09 Low fuel warning light is ON. 0 CAN communication failure during RS sequence. REMOTE STARTER SHUTDOWN ERROR CODES: NOTES The parking lights will flash four [x] times, then will flash [Y] number times to indicate an error code. See table. Automotive Data Solutions Inc. 7 PAGE OF 8 DOC.: #090 7070
I II III DURING PROGRAMMING DURING REMOTE START WITH IGNITION Automotive Data Solutions Inc. 7 DIAGNOSTIC TEST MODULE LED STATUS MODULE DIAGNOSTICS - OF Flashing RED Missing/wrong information from firmware or vehicle. Solid RED Module waiting for more vehicle information. Flashing GREEN Additional steps required to complete module programming. Solid GREEN then Module correctly programmed. No activity or module already programmed. Flashing RED Module incorrectly programmed. Solid RED Module incorrectly programmed. Flashing GREEN Module correctly programmed and operational. Solid GREEN then Reset in progress. Invalid ground when running status from remote starter. Flashing RED Module incorrectly programmed or connected. Solid RED Module not programmed. Waiting for more vehicle information. Flashing GREEN False ground when running status from remote starter. Solid GREEN then Reset in progress. Module at rest and ready for a remote start sequence. PAGE OF 8 DOC.: #090 7070
MODULE RESET PROCEDURE - OF Disconnect all connectors from module except the BLACK 0-PIN connector. 07 Reconnect all connectors. Disconnect the BLACK 0-PIN connector. 08 Repeat programming procedure. 0 PRESS AND HOLD the module s programming button while connecting the BLACK 0-PIN connector. Failure to follow procedure may result with a DTC or a CHECK ENGINE error message. 0 Wait, LED will flash RED. RELEASE programming button. 0 LED will turn RED for seconds. 0 Module RESET completed. Automotive Data Solutions Inc. 7 PAGE 7 OF 8 DOC.: #090 7070
INSTALLATION CHECKLIST - OF PAGE 8 OF 8 DOC.: #090 7070 CHECKLIST WARNING: Vehicle engine will start many times. Test in a well ventilated area. Close all vehicle doors, hood and trunk. Press the LOCK button once [x] on the aftermarket keyfob. 9 Press the START/STOP button once [x] on the aftermarket keyfob to shut down vehicle. Question 7: Does the vehicle shut down? Question : Do the doors lock? YES: Go to next step. NO: Repeat step. If problem persists, press the brake pedal once [x] to shut down the vehicle and call technical support. RAP and auto light shutdown test YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. 0 Press the UNLOCK button once [x] on the aftermarket keyfob. YES: Go to next step. NO: Verify the RAP SHUTDOWN connections as illustrated in the wiring diagram. Repeat the test and call technical support if the problem persists. Question : Do the doors unlock? Question 8: Did the radio, interior controls and headlights turn off within 0 seconds after remote start shutdown? YES: Go to next step. NO: Verify the remote programming, the RF connections and the wired door lock/unlock connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Open hood. If not already installed, affix the mandatory orange warning sticker under the hood and proceed to next step. Press the TRUNK release button once [x] on the aftermarket keyfob if supported. Press the START/STOP button once [x] on the aftermarket keyfob to remote start vehicle. Question : Does the trunk or hatch open/unlock? Question 9: Does the vehicle remote start? YES: Close trunk or hatch and go to next step. NO: Verify the remote programming, the RF connections and the wired trunk/hatch connections as illustrated in the wiring diagram, if applicable. Repeat the test and call technical support, if the problem persists. Press the AUX button once [x] on the aftermarket keyfob if supported. Enter vehicle and close the doors. Question : Does the driver side sliding door open? Press the START/STOP button once [x] on the aftermarket keyfob to remote start vehicle. YES: Press the AUX button once [x] to close the driver sliding door and go to next step. 7 Wait for the vehicle to start. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. 8 Press brake pedal. 7 Press the AUX button once [x] on the aftermarket keyfob if supported. YES: Go to next step. YES: The vehicle is not equipped with a factory hood pin. Install a mandatory aftermarket hood switch, then repeat the test. NO: Go to next step. Close hood. Question 0: Does the vehicle shut down? Question : Does the passenger side sliding door open? YES: Press the AUX button once [x] to close the passenger sliding door and go to next step. NO: Verify the remote programming and the RF connections. Repeat the test and call technical support, if the problem persists. NO: The module does NOT detect the brake pedal signal. Press the START/STOP button once [x] on the aftermarket keyfob to shut down vehicle, check connection as illustrated in the wiring diagram, if applicable, and call technical support. 9 Exit vehicle. 8 Press the START/STOP button once [x] on the aftermarket keyfob to remote start vehicle. 0 Installation checklist completed. Question : Does the vehicle remote start? YES: Go to next step. NO: Verify the remote programming, the RF connections and check the remote start error codes. Repeat the test and call technical support, if the problem persists. Automotive Data Solutions Inc. 7