HS10S-FA Water station Product specification sheet Range of Application Medium Drinking water Inlet pressure Max. 16 bar Outlet pressure 1.5-6.5 bar Installation position Horizontal with filter bowl downwards Connection size DN 65 - DN 100 Flanges on inlet and outlet Flanges PN16 acc. to DIN6021 / ISO 7005-2, EN 1092-2 The filter is constructed for drinking water installations. In case of a process water application the filter has to be proven individually. Technical Data Operating temperature Max. 65 C Nominal pressure PN16 Minimum pressure drop 1.0 bar Opening pressure check valve ca. 0.05 bar Operating pressure Min. 2.0 bar Max. 16.0 bar Diaphragm pressure loading Max. 9.0 bar Connection size DN 65 - DN 100 Application Water stations of this type are suitable for installations with high water demand. They can be used in large residential buildings, for central water supply as well as in commercial, industrial or similar applications. The unit consits of all recommended devices for protection as check valve, reverse rinsable filter and pressure reducing valve. The check valve protects the mains water system against back pressure, back flow and back syphonage of health threatening liquids. The reverse rinsable flange filter prevents the ingress of foreign bodies, for example rust particles, strands of hemp and grains of sand. It contains a highly efficient reverse rinsing filtering system and can be retrofitted with the Z11AS fully automatic reverse rinsing actuator and the DDS76 differential pressure switch. The pressure reducing valves protects installations against excessive pressure from the supply. Pressurisation damage is avoided and water consumption is reduced. Additional reduction of the operating pressure and maintaining it at a constant level minimizes flow noise in the installation. Special Features DIN/DVGW-certified check valve and filter Filter insert fully replaceable Filtered water supplied even during reverse rinsing Patented reverse rinsing system - fast and thorough cleaning of the filter with small amount of water Fully automatic reverse rinsing with retrofittable automatic reverse rinsing actuator Z11AS and differential pressure switch Powder coated cast iron gives high level of corrosion protection Non-rising stem for setting outlet pressure and position indicator on spring bonnet on pressure reducing valve The adjustment spring of the pressure reducing valve is not in contact with the potable water Inlet pressure balancing - fluctuating inlet pressure does not influence outlet pressure http://ecc.emea.honeywell.com 1
Construction The water station comprises: Check valve with o Housing and housing end casing with flanges o Check valve insert o Test and drain plugs o Disc, guide, spring, disc lip seal ring Fine filter with o Housing with pressure gauge ports (1x inlet, 2x outlet) o 2 pressure gauges (1x inlet, 1x outlet including memory indicator) o PN 16 flanges to EN 1092-2 o Fine filter o Filter bowl o Ball valve with lever and drain funnel Pressure reducing valve with o Housing with PN16 flanges per ISO7005-2, EN1092-2, face to face length acc. EN 55-1 o Spring bonnet with adjustment screw oadjustment spring ocartridge insert o Pressure gauge Method of Operation Spring loaded check valves have a moving seal disc which is lifted off the seat by a greater or lesser amount depending on the flow rate through the valve. If the flow falls towards zero, then the spring pushes the disc back onto the seat and seals the waterway. To ensure continuing correct function it is recommended that check valves be regularly checked and maintained (as specified in EN 1717). The filter insert is divided into two parts. In the filtering position, only the lower, larger section is rinsed through by water jets from outside to inside. The small upper section does not come in contact with unfiltered water. When the ball valve is opened for reverse rinsing, then the whole filter insert is pushed downwards until the water supply to the outer side of the main filter is stopped. Simultaneously, the water flow is opened to the upper part of the filter. The water needed for cleaning the filter passes through the upper filter section, then the rotating impeller and the main filter from inside to outside, i.e. the filter is reverse rinsed with filtered water. In that way the upper filter is also cleaned by Options HS10S-...FA =Standard version with flanges PN16, Filter mesh size 100μm Connection size Materials Check valve o Grey cast iron housing end and housing o Stainless steel screws and nuts o Stainless steel disc o Stainless steel spring o EPDM for lip seal ring Fine filter o Housing and filter bowl made of ductile cast iron (EN-GJS- 400-15), coated with PA (polyamide) o Inner parts made of stainless steel, red bronze, brass and plastic o Fine filter made of stainless steel Pressure reducing valve o Housing made of ductile cast iron (EN-GJS-400-15 EN1563), coated with PA (polyamide) o Spring bonnet made of ductile cast iron (EN-GJS-400-15 EN1563), coated with PA (polyamide) o Cartridge insert DN65 - DN100 made of low-lead DZR brass (<2.2% acc. to DIN 50930 part 6) with stainless steel valve spindle. o Spring steel adjustment spring o Diaphragm and seals made of EPDM o Groove ring and sealing disc made of high-quality PU o Stainless steel screws and nuts jets from the impeller. The filter automatically switches back to the operating position when the ball valve is closed again. Spring loaded pressure reducing valves operate by means of a force equalising system. The force of a diaphragm operates against the force of an adjustment spring. If the outlet pressure and therefore diaphragm force fall because medium is drawn, the then greater force of the spring causes the valve to open. The outlet pressure then increases until the forces between the diaphragm and the spring are equal again. The inlet pressure has no influence in either opening or closing of the valve. Because of this, inlet pressure fluctuation does not influence the outlet pressure, thus providing inlet pressure balancing. 2 http://ecc.emea.honeywell.com
h H F DN R l1 R L Connection size DN 65 0 100 Weight approx. kg 5 99 146 Dimensions mm L 20 0 1000 H 04 7 90 h 434 50 610 F 15 200 220 l 1 175 225 250 Test and drain plug R 1 / 2" 1 / 2" 1 / 2" k vs-value 47 70 110 DIN/DVGW Registration No. Check valve Filter Pressure reducing valve NW - 6310 BU 0492 requested NW-6330CN0112 Accessories Z11AS Automatic reverse rinsing actuator Z11AS FY69P DDS76 FY69P For automatic reverse rinsing of the filter at presettable intervals Differential pressure switch Strainer With double mesh, grey cast iron housing, powder coated inside and outside. A = Mesh size approximately 0.5 mm DDS76 http://ecc.emea.honeywell.com 3
Installation Example Installation Guidelines Install in horizontal pipework with test and drain plugs and filter bowl downwards and spring bonnet upwards o This position ensures optimum draining and filter efficiency Install shutoff valves o Shutoff valves provide optimal serviceability Ensure good access o Pressure gauge can be read off easily o Simplifies maintenance and inspection The installation location should be protected against frost Fit immediately after water meter o Corresponds to EN 06-2 Provide a straight section of pipework of at least five times the nominal valve size after the pressure reducing valve (in accordance with EN06-2) Typical Applications Water stations of this type are suitable for use as a safety device on water installations as well as for district water supply mains as specified in EN 1717. They can also be used for commercial, industrial or similar water supply systems. The following are some typical applications: After a water meter As a safety device up to liquid category 2 of EN 1717 Upstream of water heating installations In transfer points of central water supply systems if drainage is available If the downstream system includes appliances which must be protected against dirt If the static pressure exceeds the maximum permissible value for the system If pressure fluctuations in the downstream system must be avoided To reduce the water consumption Possible applications e.g. in laundries, refineries, district heating systems or central water supply systems 4 http://ecc.emea.honeywell.com
Spare Parts Water station with flanges HS10S-FA (from 2010 onwards) No. Description Dimension Part No. 2 1 4 3 1 Valve disc guide DN65 0900376 DN0 0900377 DN100 090037 2 Lip seal ring DN65 5350000 DN0 5350300 DN100 5350400 3 Hexagonal blanking plug DN65 - DN100 224700 4 3 4 Seal ring DN65 - DN100 5350500 http://ecc.emea.honeywell.com 5
7 7 9 5 6 No. Description Dimension Part No. 5 Filter insert complete Filter mesh 100 μm DN 65 AF7TS-065A DN 0 AF7TS-00A DN 100 AF7TS-100A Filter mesh 50 μm DN 65 AF7TS-065C DN 0 AF7TS-00C DN 100 AF7TS-100C Filter mesh 200 μm DN 65 AF7TS-065D DN 0 AF7TS-00D DN 100 AF7TS-100D 6 Replacement sieve Filter mesh 100 μm DN 65 ES7TS-065A DN 0 ES7TS-00A DN 100 ES7TS-100A Filter mesh 20 μm DN 65 ES7TS-065B DN 0 ES7TS-00B DN 100 ES7TS-100B Filter mesh 50 μm DN 65 ES7TS-065C DN 0 ES7TS-00C DN 100 ES7TS-100C Filter mesh 200 μm DN 65 ES7TS-065D DN 0 ES7TS-00D DN 100 ES7TS-100D 7 Pressure gauge 0-16 bar, G1/4 M7M-A16 0-16 bar, G1/4 with memory M7M-A16MR indicator Seal set complete DN 65 SOS7TS-065 DN 0 SOS7TS-00 DN 100 SOS7TS-100 9 Ball valve 5622100 http://ecc.emea.honeywell.com 6
No. Description Dimension Part No. 10 Valve insert complete DN65-100 0904120 11 Set of seals complete DN65-100 0904121 12 Pressure gauge M39M-A10 Ranges 0-10 bar 13 Pressure gauge M39M-A16 Ranges 0-16 bar 10 11 13 11 12 11 http://ecc.emea.honeywell.com 7
Automation and Control Solutions Honeywell GmbH Hardhofweg 7421 MOSBACH GERMANY Phone: (49) 6261 10 Fax: (49) 6261 1309 http://ecc.emea.honeywell.com Manufactured for and on behalf of the Environmental and Combustion Controls Division of Honeywell Technologies Sàrl, Z.A. La Pièce 16, 110 Rolle, Switzerland by its Authorised Representative Honeywell GmbH EN0H-1155GE23 R0316 Subject to change without notice 2016 Honeywell GmbH