Rough Terrain Forklifts 1120A FORKLIFT l 220A FORKLIFT l 220A VERSLIFT
Engineered for m manoeuvrability Bell s range of forklifts have been engineered in response to a need for a manoeuvrable, lifting machine for use on rough terrain work sites. The Bell rough terrain Forklift has been the machine of choice in many applications, notably in brick yards, chicken farms and timber yards. It s low maintenance cost, low fuel burn and low capital cost, result in a lowest cost solution for these challenging applications. The Bell philosophy of Strong Reliable Machines is clearly stamped on these products. Our network of aftersales centres provide the Strong Reliable Support expected by Bell customers. 2
ore 3
Specifications - 120A FORKLIFT Engine Deutz F3L912, 3 cylinder, in-line, air cooled with integrated blower fan Engine Capapcity 2.827 l Governed Power 28 kw Max Torque 160 Nm @ 1400 rpm Governed Full Power Engine Speed 1 800 rpm Max. rated speed 2 500 rpm Aspiration Naturally aspirated Engine Mounting 3 point rigid mounting Sump Material Cast aluminium Oil 9 l Blower Failure Warning Mechanical linkage induces injector pump shut-off Low Idle 800 rpm High Idle 2 250 rpm Fuel Filtration Two stage. Spin-on water separator primary, replaceable spin-on secondary Oil Filtration Replaceable spin-on paper-type micro filter- full flow EXHAUST Engine manifold mounted mild steel silencer with short side-pointing tail pipe AIR CLEANER Dual (primary & safety) paper element cyclonic canister type with restriction visual indicator PRE CLEANER SYSTEM Cyclonic dust bowl. FUEL INLET SYSTEM Water Separator Primary Filter- spin-on Frame mounted, 5 microns Secondary Filter- spin-on Engine mounted, 5 microns ENGINE/TRANS. COUPLING Bell nylon gear coupling DRIVE PUMPS Eaton 78363 Axial piston, closed loop, manual control swash plate Control Direct control, foot linkage DRIVE MOTORS Eaton 74315 Axial piston, closed loop TRANSMISSION CHARGE CIRCUIT Bosch Rexroth Single Aluminium gear pump 16 cc/rev Pump Flow @ Governed Engine 28.8 l/min @ rpm Relief Pressure Setting 17 bar Pressure Filter Rating- beta 75 Rating 13 Micron DRIVE WHEELS Drive Tyre All Traction Field & Road - 10 ply with inner tube Drive Tyre Size 14.9 x 24 Drive Wheel Rim 12 x 24, 1 piece Drive Wheel Inflation Pressure 2.0 bar Unladen Ground Pressure Rear 0.95 bar Drive Wheels Tractive Effort 28.365 kn-machine Road Speed 8.5 km/hr at governed engine speed TAIL WHEEL Tail Wheel Tyre High Flotation Implement, 10 Ply with inner tube Tail Wheel Tyre Size 400 x 15.5 Tail Wheel Rim 13 x 15.5, 1 piece Tail Wheel Inflation Pressure 2.0 bar Unladen Ground Pressure Rear 0.95 bar BRAKES Service Brake Closed Loop Hydrostatic Wheel retardation Park Brake Spring applied, hydraulic release wet multi disc HYDRAULIC TANK Integral with tubular frame Oil Rando HDZ 68 Hydraulic fluid 120 l (130 l for system) Maximum Operating Temp 90 deg C @ 45 ambient IMPLEMENT HYD SYSTEM Fixed displacement open centre seperate gear pumps with full flow suction filtering. WO return filtration or cooling Suction Filtration 20 micron BOOM/MAST HYDRAULIC FUNCTION Pump Eaton #26 Pump Gear, open centre, Trans.pump thru-drive 29 cc/rev NON-BOOM AUX HYD FUNCTIONS Pump Gear, open centre, engine geartrain drive 16 cc/rev Pump Flow @ Governed Engine 28.8 l/min @ rpm FUEL TANK Remote to frame, rear mounted 76 l ELECTRICAL SYSTEM Voltage 12 V Lighting Frame mounted foward and rear Lockable Isolater Switch Battery mounted fuse, 300 Amp. Fall system protection via resetable circuit breakers. CABIN Integral with steel frame. No doors. Guarding HD windscreen guard & bonnet guard. Rear engine bay doors SAFETY/ERGONOMICS Over-centre lock-down latches x2 to prevent accidental seat plate tip-up; Low profile padded seat with lap strap seat belt; Frame post mounted rearview mirrors WARNING LIGHTS Pressure sensor alternator charge light Operating Masses Unladen Front 3,000 kg Unladen Rear 1,700 kg Unladen Total 4,700 kg Shortest Wheelbase 2,458 kg Load distance ahead of front axle 1,170 m Outstretched Tipping load 3,571 kg SWL - Payload 2,500 kg SWL Laden Front 6,690 kg SWL Laden Rear 510 kg SWL Laden Total 7,200 kg STEERING SYSTEM Front wheel hydraulic skid steer via foot operated treadle control system 4
Dimensions 2 200 mm 11º 6º 2 440 mm Mast Down 3 280 mm Max. Lift 4 100 mm Overall raising Height 250 mm 2 550 mm 450 mm 2 385 mm 4 585 mm 2.5 ton CAPACITY Lowest cost per ton solutions Low fuel consumption low maintenance Designed for rough terrain operations, where agility and a light foot print are requirements 5
Specifications - 220A FORKLIFT Engine Deutz F4L912, 4 cylinder, in-line, air cooled with integrated blower fan Engine 3.770 l Governed Power 46 kw Max Torque 230 Nm @ 1500 rpm Governed Full Power Engine Speed 2 150 rpm Max. rated speed 2 500 rpm Aspiration Naturally aspirated Engine Mounting 3 point rubber mounting Sump Material Cast aluminium Oil 9 l Blower Failure Warning Mechanical linkage induces injector pump shut-off Low Idle 800 rpm High Idle 2 250 rpm Fuel Filtration Two stage. Spin-on water separator primary, replaceable spin-on secondary Oil Filtration Replaceable spin-on paper-type micro filter- full flow EXHAUST Rigid frame mounted stainless steel vertical silencer with short stack pipe outlet DRIVE PUMPS Eaton 78363 Axial piston, closed loop, manualcontrol swash plate Control Direct control, foot linkage 40.6 cc/rev per wheel Relief Pressure 276 bar Flow Rate at Governed RPM 87.29 l/min per wheel DRIVE MOTORS Eaton 74318 Axial piston, closed loop TRANSMISSION CHARGE CIRCUIT Bosch Rexroth Single Aluminium gear pump 16 cc/rev Pump Flow @ Governed Engine 34.4 l/min @ rpm Relief Pressure Setting 17 bar Pressure Filter Rating- beta 75 Rating 13 Micron DRIVE WHEELS Drive Tyre All Traction Field & Road - 10 ply with inner tube Tail Wheel Inflation Pressure 3.0 bar Unladen Ground Pressure Rear 1.28 bar BRAKES Service Brake Closed Loop Hydrostatic Wheel retardation Park Brake Spring applied, hydraulic release wet multi disc HYDRAULIC TANK Integral with tubular frame Oil Rando HDZ 68 Hydraulic fluid 140 l (150 l for system) Maximum Operating Temp 90 deg C @ 45 ambient IMPLEMENT HYD SYSTEM Fixed displacement open centre seperate gear pumps with full flow suction filtering. WO return filtration or cooling Suction Filtration 20 micron BOOM/MAST HYDRAULIC FUNCTION Pump Eaton #26 Pump Gear, open centre, Trans.pump thru-drive 29 cc/rev STEERING SYSTEM Front wheel hydraulic skid steer via foot operated treadle control system CABIN Integral with steel frame. No doors. Guarding HD windscreen guard & bonnet guard. Rear engine bay doors SAFETY/ERGONOMICS Over-centre lock-down latches x2 to prevent accidental seat plate tip-up; Low profile padded seat with lap strap seat belt; Frame post mounted rearview mirrors WARNING LIGHTS Oil pressure sensor alternator charge light Operating Masses Unladen Front 3,400 kg Unladen Rear 2,278 kg Unladen Total 5,678 kg Shortest Wheelbase 2,568 kg Load distance ahead of front axle 1,170 m Outstretched Tipping load 5,000 kg SWL - Payload 3,500 kg SWL Laden Front 8,495 kg SWL Laden Rear 683 kg SWL Laden Total 9,178 kg AIR CLEANER Dual (primary & safety) paper element cyclonic canister type with restriction visual indicator PRE CLEANER SYSTEM Cyclonic dust bowl. FUEL INLET SYSTEM Water Separator Primary Filter- spin-on Frame mounted, 5 microns Secondary Filter- spin-on Engine mounted, 5 microns ENGINE/TRANS. COUPLING Bell nylon gear coupling Drive Tyre Size 18.4 x 26 Drive Wheel Rim 16 x 26, 1 piece Drive Wheel Inflation Pressure 1.5 bar Unladen Ground Pressure Rear 0.49 bar Drive Wheels Tractive Effort 29.019 kn-machine Road Speed 10.00 km/hr at governed engine speed TAIL WHEEL Tail Wheel Tyre High Flotation Implement, 10 Ply with inner tube Tail Wheel Tyre Size 400 x 15.5 Tail Wheel Rim 13 x 15.5, 1 piece NON-BOOM AUX HYD FUNCTIONS Pump Gear, open centre, engine geartrain drive 22.5 cc/rev Pump Flow @ Governed Engine 48.4 l/min @ rpm FUEL TANK Remote to frame, rear mounted 76 l ELECTRICAL SYSTEM Voltage 12 V Lighting Frame mounted foward and rear Lockable Isolater Switch Battery mounted fuse, 300 Amp. Fall system protection via resetable circuit breakers. 6
Dimensions 2 200 mm 11º 6º 2 440 mm Mast Down 3 280 mm Max. Lift 4 100 mm Overall Raising Height 250 mm 2 550 mm 450 mm 2 385 mm 4 585 mm 3.5 ton CAPACITY Lowest cost per ton solutions Low fuel consumption low maintenance Designed for rough terrain operations Where agility and productivity are requirements 7
Specifications - 220A VERSALIFT Engine Deutz F4L912, 4 cylinder, in-line, air cooled with integrated blower fan Engine 3.770 l Governed Power 46 kw Max Torque 234 Nm @ 1500 rpm Governed Full Power Engine Speed 2 150 rpm Max. rated speed 2 500 rpm Aspiration Naturally aspirated Engine Mounting 3 point rubber mounting Sump Material Cast aluminium Oil 9 l Blower Failure Warning Mechanical linkage induces injector pump shut-off Low Idle 800 rpm High Idle 2 250 rpm Fuel Filtration Two stage. Spin-on water separator primary, replaceable spin-on secondary Oil Filtration Replaceable spin-on paper-type micro filter- full flow EXHAUST Rigid frame mounted stainless steel vertical silencer with short stack pipe outlet AIR CLEANER Dual (primary & safety) paper element cyclonic canister type with restriction visual indicator PRE CLEANER SYSTEM Cyclonic dust bowl. DRIVE PUMPS Eaton 78363 Axial piston, closed loop, manualcontrol swash plate Control Direct control, foot linkage 40.6 cc/rev per wheel Relief Pressure 276 bar Flow Rate at Governed RPM 87.29 l/min per wheel DRIVE MOTORS Eaton 74315 Axial piston, closed loop TRANSMISSION CHARGE CIRCUIT Bosch Double Aluminium gear pump 16 cc/rev Pump Flow @ Governed Engine 34.4 l/min @ rpm Relief Pressure Setting 17 bar Pressure Filter Rating- beta 75 Rating 13 Micron DRIVE WHEELS Drive Tyre Earthmover 12 ply - L3, tubeless Drive Tyre Size 17.5 x 25 Drive Wheel Rim 14 x 25, 1 piece Drive Wheel Inflation Pressure 1.5 bar Unladen Ground Pressure Rear 0.60 bar Drive Wheels Tractive Effort 29.019 kn-machine Unladen Ground Pressure Rear 1.15 bar BRAKES Service Brake Closed Loop Hydrostatic Wheel retardation Park Brake Spring applied, hydraulic release wet multi disc ATTACHMENT 1 cu m GP bucket, 1.2m Class II fork tynes 1 m 3 HYDRAULIC TANK Integral with tubular frame Oil Rando HDZ 68 Hydraulic fluid 140 l (150 l for system) Maximum Operating Temp 90 deg C @ 45 ambient IMPLEMENT HYD SYSTEM Fixed displacement open centre seperate gear pumps with full flow suction filtering. WO return filtration or cooling Suction Filtration 20 micron BOOM/MAST HYDRAULIC FUNCTION Pump Eaton #26 Pump Gear, open centre, Trans.pump thru-drive 29 cc/rev NON-BOOM AUX HYD FUNCTIONS Pump Gear, open centre, engine geartrain drive Lighting Frame mounted foward and rear Lockable Isolater Switch Battery mounted fuse, 300 Amp. Fall system protection via resetable circuit breakers. STEERING SYSTEM Front wheel hydraulic skid steer via foot operated treadle control system STANDARD CHOICES Fork frame, 1.8 m Class 2; Fork Frame 1,2 Class 2; Bucket, 1 m 3 2.2 m wide CABIN Integral with steel frame. No doors. Guarding Rear engine bay doors SAFETY/ERGONOMICS Over-centre lock-down latches x2 to prevent accidental seat plate tip-up; Low profile padded seat with lap strap seat belt; Frame post mounted rearview mirrors WARNING LIGHTS Oil pressure sensor alternator charge light Operating Masses Unladen Front 3,834 kg Unladen Rear 2,046 kg Unladen Total 5,880 kg Shortest Wheelbase 2,568 kg Load distance ahead of front axle 1,839 m Outstretched Tipping load 2,857 kg SWL - Payload 2,000 kg SWL Laden Front 7,266 kg SWL Laden Rear 614 kg SWL Laden Total 7,880 kg FUEL INLET SYSTEM Water Separator Primary Filter- spin-on Frame mounted, 5 microns Secondary Filter- spin-on Engine mounted, 5 microns ENGINE/TRANS. COUPLING Bell nylon gear coupling Road Speed 9.5 km/hr at governed engine speed TAIL WHEEL Tail Wheel Tyre High Flotation Implement, 10 Ply with inner tube Tail Wheel Tyre Size 400 x 15.5 Tail Wheel Rim 13 x 15.5, 1 piece Tail Wheel Inflation Pressure 2.0 bar 22.5 cc/rev Pump Flow @ Governed Engine 48.4 l/min @ rpm FUEL TANK Remote to frame, rear mounted 76 l ELECTRICAL SYSTEM Voltage 12 V 8
Dimensions 836 (2'9") 3 181 (10'6") 1 948 (6'5") 2 040 (6'9") 2 199 (7'3") 338 (1'1") 2 440 (8') 2670 (8'9") 4 124 (13'8") 464 (1'6") 1 793 (5'11") 589 (1'11") 2 496 (8'3") 2 679 (8'10") 5 732 (18'10") Overall width of machine: 2 600 (8'7") 3 500 3 000 HEIGHT OF THE LOWER FACE OF THE FORK ABOVE THE GROUND LEVEL IN mm (*) 2 500 2 000 1 500 1 000 500 NOTE: THE ABOVE SAFE WORKING LOADS ARE ALL WITH A 500mm LOAD CENTRE 500 05 00 1 000 1 500 2 000 2 500 WEIGHT IN Kg 9
Verslift Options Buckets 0,8-1,8 m 3 Fork Frames 1,8 m Class 2 or 3; 2,6 m Class 2 or 3 Tymes: 1,2 m Class 2 or 1,5 m Class 3 Lift Platform Material Handling Boom Lifting Extension Dangle Grab Bag Handling 10
Notes 11
All dimensions are shown in millimetres, unless otherwise stated between brackets. Under our policy of continuous improvement, we reserve the right to change technical data and design without prior notice. Photographs featured in this brochure may include optional equipment. BELL INTERNATIONAL: Tel: +27 (0) 35-907 9431 E-mail: marketing@bellequipment.com Web: www.bellequipment.com Tel: +61 (0) 8 9356 1033 Tel: +33 (0) 5 55 89 23 56 Tel: +49 (0) 6631 / 91 13-0 Tel: +7 495 287 80 02 Tel: +27 (0) 11-928-9700 Tel: +34 91 879 60 19 Tel: +44 (0) 1283 712862 Tel: +1 912 527 3309 Broch/1377/06/13 Forklifts English