Number Selection Tray Tray covers are available for all classes of tray. They should be installed where falling objects may damage cables or where vertical tray run is accessible by pedestrian or vehicular traffic. Cover mounting hardware must be ordered separately. Solid These covers provide maximum mechanical protection for cables with limited heat build up. Solid covers are available with or without flange. Flanged covers have 1/2 in. flange. Cover mounting hardware must be ordered separately. Ventilated Flanged This design offers excellent mechanical protection while allowing heat produced by cables to dissipate. Cover mounting hardware must be ordered separately. For extreme applications : Peaked flanged covers, peaked ventilated covers Peaked covers offer mechanical protection, reduce pooling of liquids on the cover and the accumulation of snow or ice. Peaked covers have 15 angle. Cover mounting hardware must be ordered separately. A94
Straight Cover Number Selection (ABW-3-12)-SNC-72 Material Prefix Cover Series Width Cover Type Length ABW Aluminum 3 SNC Solid non-flanged cover SFC Solid flanged cover VFC Ventilated flanged cover PFC Peaked flanged cover* PVC Peaked ventilated flanged cover * 72 (72 in.) 3 (3 m) Fittings Cover Number Selection AUW-12-SNC-HB90-24 Material Prefix Fitting Style Prefix Width Cover Type Fitting Type Degree Nominal Radius A Aluminum UW U-Beam HB Horizontal bend VI Vertical inside bend SNC Solid non-flanged cover SFC Solid flanged cover VFC Ventilated flanged cover 30 (30 ) 45 (45 ) 60 (60 ) 90 (90 ) A95
Fittings Cover Number Selection AUW-18-12-SNC-RT-12 Material Prefix Fitting Style Prefix Width 1 Width 2** Cover Type Fitting Type Radius* A Aluminum UW U-Beam NOTE: For ET and EX, W2 > W1. For RT, HSR, HLR, HRR, W1 > W2. ** Not required for VTU, HYR, HYL, HT, HX * Radius not required for HSR, HLR, HRR, HYR, HYL. SNC Solid non-flanged cover SFC Solid flanged cover VFC Ventilated flanged cover RT Horizontal reduce tee ET Horizontal expand tee EX Horizontal expand cross HSR Horizontal straight reducer HLR Horizontal left reducer HRR Horizontal right reducer HT Horizontal tee HX Horizontal cross VTU Vertical tee up HYR Horizontal wye right HYL Horizontal wye left Fittings Cover Number Selection AUW-4-12-SNC-VO90-24 Material Prefix Fitting Style Prefix Side Rail Height Width Cover Type Fitting Type Degree* Nominal Radius A Aluminum UW U-Beam 4 (4 in.) 5 (5 in.) 6 (6 in.) 7 (7 in.) Note: For peaked fitting covers refer to pages A95 to A97 * Not required for VTD nor for CS SNC Solid non-flanged cover SFC Solid flanged cover VFC Ventilated flanged cover VO Vertical outside bend VTD Vertical tee down CS Cable support 30 (30 ) 45 (45 ) 60 (60 ) 90 (90 ) A96
Peaked Horizontal Bend / Vertical Inside Bend Horizontal Bend Aluminum Number Selection AUW-12-PFC-HB-90-24 Material Fitting Style Width Cover Type Fitting Type Degree Nominal Radius A Aluminum Note: Pregalvanized not available UW U-Beam PFC Peaked flanged cover PVC Peaked ventilated flanged cover HB Horizontal bend VI Vertical inside bend 30 (30 ) 45 (45 ) 60 (60 ) 90 (90 ) A97
Peaked Vertical Outside Bend Aluminum Number Selection AUW-4-12-PFC-VO-90-24 Material Prefix A Aluminum Fitting Style Prefix UW U-Beam Note: Pregalvanized not available Side Rail Height Width Cover Type Fitting Type Degree 4 (4 in.) 5 (5 in.) 6 (6 in.) 7 (7 in.) PFC Peaked flanged cover PVC Peaked ventilated flanged cover VI Vertical outside bend 30 (30 ) 45 (45 ) 60 (60 ) 90 (90 ) Nominal Radius A98
Peaked Horizontal Tee Aluminum Number Selection AUW-12-PFC-HT-24 Material Prefix Fitting Style Prefix Width Cover Type Fitting Type Nominal Radius A Aluminum UW U-Beam PFC Peaked flanged cover HT Horizontal tee PVC Peaked ventilated flanged cover Note: Pregalvanized not available 09 (9 in. A99
Accessories For Quantity of Standard Cover Clamps Required Straight section 1.8 m (6 ft.) 4 pcs. Tees 6 pcs. Straight section 3 m (10 ft.) and 3.7 m (12 ft.) 6 pcs. Crosses 8 pcs. Horizontal and vertical bends IMPORTANT NOTE: B in CAT. NO. indicates this accessory can be used for both styles. Note: when using heavy-duty cover clamp, only half the quantity of pieces are required. Economical Cover Clamp 4 pcs. Cat. No. Material Side Rail Height ABW-SCC Aluminum All Sizes Cannot be used with U-Style fittings. Rigid indoor cover clamp for flat and flanged covers. Universal Fitting Cover Clamp Cat. No. Material Side Rail Height ABW(*)FCC Aluminum 4 (*) Insert side rail height 5 6 7 Rigid indoor cover clamp for flat and flanged covers. Heavy-Duty Cover Clamp Cat. No. Material Side Rail Height Tray Width (in.) ABW4(*)HCC 4 06 ABW5(*)HCC 5 09 Aluminum ABW6(*)HCC 6 12 ABW7(*)HCC 7 18 (*) Insert tray width 24 Wraparound design offers added protection for rugged applications and outdoor conditions. Hardware included. 30 A100
Accessories For Extreme Heavy-Duty Cover Clamp Cat. No. Material Side Rail Height Tray Width (in.) ABW4(*)ECC 4 06 ABW5(*)ECC 5 09 Aluminum ABW6(*)ECC 6 12 ABW7(*)ECC 7 18 (*) Insert tray width 24 Wraparound design offers added protection for rugged applications and outdoor conditions. Hardware included. 30 Heavy-Duty Peaked Cover Clamp Cat. No. Material Side Rail Height Tray Width (in.) ABW4(*)HPC 4 06 ABW5(*)HPC 5 09 Aluminum ABW6(*)HPC 6 12 ABW7(*)HPC 7 18 (*) Insert tray width 24 30 Wraparound design formed to fit peaked cover for outdoor applications. Hardware included. Hold Down Clamp Cat. No. Material Side Rail Height ABW(*)HDC Aluminum 4 Note: Hardware included (*) Insert side rail height 5 6 7 Designed to secure cable tray to support system. A101
Accessories For Raised Cover Clamp Cat. No. Material Cover Series Cover Offset (in.)* Cover Side rail ABW3(*)RCC Aluminum 3 1 (*) Cover offset. Designed to raise cover above tray for added ventilation. Note: For straight section and PFC and SFC covers only. 2 3 4 Peaked End Cap Cat. No. Material Tray Width (in.) ABW(*)PEC Aluminum 06 (*) Insert tray width Used for transition between peaked covers to straight covers. 09 12 18 24 30 Cover Joint Strip Cat. No. Material Tray Width (in.) ABW(*)PCS Plastic 06 (*) Insert tray width Strip used for joining flat covers end to end. 09 12 18 24 30 A102