INSTALLATION INSTRUCTIONS Accessory Application Publications No. ACCORD AII 24050 4-DOOR P/N 08V31-SDA-100 Issue Date AUG 2002 NOTE: The outside temperature gauge cannot be installed in a vehicle with fog lights. Fog light harness PARTS LIST Right fog light Switch harness Left fog light Right bracket A Switch Template A Left bracket A Template B Right bracket B Relay (black) Left bracket B Relay (gray) Right trim Fuse label Left trim 4 Self-tapping screws, 5 x 12 mm 2002 American Honda Motor Co., Inc - All Rights Reserved. AII 24050 (0208) 08V31-SDA-1000-91 1 of 19
2 Step-screws (with rubber) 2 Step-screws 2 Ground bolts Washer 3 Washer-bolts 3 Washer-screw TOOL AND SUPPLIES REQUIRED #2 Phillips screwdriver Small flat-tip screwdriver Felt-tip pen 10 mm Combination wrench 10 mm Socket Ratchet Measure 3 mm and 7 mm Drill bits Eye protection (face shield, safety goggles, etc.) File Diagonal cutters 20 mm Hole saw Drill Masking tape Thumbtack Drill stopper Scissors Hacksaw blade Illustration of the Fog Lights Installed on the Car 25 Wire ties FOG LIGHT Relay bracket 4 Self-tapping screws, 4 x 16 mm Fuse (20A) RIGHT FOG LIGHT LEFT (2) 2220010T 2221010T 2221020T 2225014T 2 of 19 AII 24050 (0208) 2002 American Honda Motor Co., Inc - All Rights Reserved.
INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your car. These procedures should not be attempted by do-it-yourselfers. 1. Make sure you have the anti-theft code for the radio, then write down the frequencies for the preset buttons. 2. Disconnect the negative cable from the battery. Installing Fog Lights 3. Install the left trim to the left bracket A with two 4 x 16 mm self-tapping screws. STEP- SCREW LEFT LEFT TRIM LEFT TRIM 4. Install the left fog light to the left trim with the one step-screw (with rubber), step-screw and washerscrew. WASHER- SCREW STEP-SCREW (WITH RUBBER) 5. Repeat steps 3 and 4 to install the right fog light. 4 x 16 mm SELF-TAPPING SCREWS (2) Cutting the Front Bumper. 6. Using the scissors, cut out template A. Position template A on the front bumper as shown, and mark the bumper at each of the two marks indicated on template A with a felt-tip pen. LEFT BRACKET A FELT-TIP PEN MARK TEMPLATE A MARK MARKS ON TEMPLATE FELT-TIP PEN TEMPLATE A TEMPLATE A Align end of template with end of bumper 7. Remove template A. 2002 American Honda Motor Co., Inc - All Rights Reserved. AII 24050 (0208) 3 of 19
8. Align template B with the marks you just made, and mark the bumper at the two marks indicated on template B with a felt-tip pen. Remove template B. 10. Using a thumbtack, mark the front bumper at the centers of the five marks indicated on the template A. If equipped with a front spoiler, measure and cut off template B, and align template B on the front bumper. MARKS (5) THUMBTACK FELT-TIP PEN MARK TEMPLATE B TEMPLATE B 35 mm FELT-TIP PEN MARK Cut off. 2225021T 2225030T THUMBTACK 2225050T 9. Align template A with the marks you just made. Tape template A to the bumper with strips of masking tape. 11. Using a felt-tip pen, mark the front bumper along outer edge of template A. TEMPLATE A MASKING TAPE MARK MARK TEMPLATE A 2225040T 12. Remove template A. MARK FELT-TIP PEN 2225061T 4 of 19 AII 24050 (0208) 2002 American Honda Motor Co., Inc - All Rights Reserved.
13. To prevent damage to the front bumper, apply a piece of masking tape in the area shown. MARKS (5) 17. Hook the fog light tabs on bracket A under the edge of the bumper hole. With the tabs on bracket A hooked on the edge of the bumper hole, position the left fog light on the front bumper as shown. Open the two screw covers. Using a felttip pen, mark the trim at the center of each hole concealed under the screw cover as shown. TAB 20 mm HOLE SAW 20 mm HOLE SAW 2225070T SCREW S HOLE 14. While wearing eye protection, drill a 20 mm hole through each of the five marked locations using a 20 mm hole saw. 15. Using a straight edge, mark between the two inboard hole. LEFT FOG LIGHT 18. Remove the left fog light. FELT-TIP PEN CENTER 2225091T 19. While wearing eye protection, drill a 7 mm hole through the bumper at each of the two marks made in step 17. First drill with a 3 mm bit, and finish with a 7 mm bit. Remove any burrs from the edges of the holes. NOTE: To prevent damaging the vehicle frame, use a drill stopper around the drill bit 10 mm from the end. DRILL STOPPER 10 mm DRILL BIT MARKS STRAIGHT EDGE MARKING AREA HACKSAW BLADE 2225080T 16. Using a hacksaw blade, cut out the front bumper along the lines made in steps 11 and 15. Remove any burrs from the edge of the hole with a file. DRILL (First drill with a 3 mm bit, and finish with a 7 mm bit.) 20. Repeat steps 6 through 19 to install the right fog light. 2002 American Honda Motor Co., Inc - All Rights Reserved. AII 24050 (0208) 5 of 19
Routing the Fog Light Harness 21. Open the hood. Remove the radiator cover (ten clips and four retaining tabs). 23. Remove the air duct cover (two clips and pull it out toward you). Remove the air duct cover by pulling it out toward you. L4 Engine Model CLIPS (10) CLIPS (2) AIR DUCT RETAINING TAB 22. Remove the hood latch cover (one clip). RADIATOR 2201032T AIR DUCT 2213010T CLIP HOOD LATCH V6 Engine Model CLIP AIR DUCT 2212012T AIR DUCT 2704010T 6 of 19 AII 24050 (0208) 2002 American Honda Motor Co., Inc - All Rights Reserved.
24. Route the fog light harness 2-pin connector through the front bulkhead and alongside the vehicle harness. 27. On left side of vehicle, secure the fog light harness to the vehicle harness with the five wire ties in the areas shown. Push the fog light harness clip into the hole in the body panel. 2-PIN HOLE 25. Route the ground bolt in the fog light harness alongside the vehicle harness across the front bulkhead to the right side of the vehicle. 2226010T CLIP 2226101T GROUND TERMINAL HOOD LATCH BRACKET GROUND BOLT 28. On the right side of vehicle, secure the fog light harness to the vehicle harness with the four wire ties. S WASHER WIRE TIE BOLT (Discard.) WIRE TIE GREEN TAPE 2226091T 26. Remove and discard the lower bolt that secures the hood latch bracket. Using one ground bolt and the 6 mm washer supplied, attach the fog light harness ground terminal to the hood latch bracket. ( Do not allow the harness to contact the air conditioner pipe.) 2704071T 2002 American Honda Motor Co., Inc - All Rights Reserved. AII 24050 (0208) 7 of 19
29. Insert the tab from left bracket B through the left fog light opening, and attach bracket B to the grille hole in the bumper grille. 31. Insert the tab from right bracket B through the left fog light opening, and attach bracket B to the grille hole in the bumper grille. GRILLE LEFT BRACKET B RIGHT BRACKET B GRILLE TAB SQUARE HOLE 2225100T SQUARE HOLE 2225120T 30. Connect the fog light harness 2-pin connector to the left fog light, and position the fog light on the front bumper. Open the screw covers, and attach the left fog light to the front bumper with two 5 x 12 mm self-tapping screws. Close the screw covers. 32. Attach the fog light harness wire connector to the right fog light with the washer-screw. WASHER-SCREW 2-PIN WIRE SCREW LEFT RIGHT 2225130T 5 x 12 mm SELF- TAPPING SCREW 2225110T 8 of 19 AII 24050 (0208) 2002 American Honda Motor Co., Inc - All Rights Reserved.
33. Connect the fog light harness 2-pin connector to the right fog light, and position the right fog light on the front bumper. Open the screw covers, and attach the right fog light to the front bumper with the two 5 x 12 mm self-tapping screws. Close the screw covers. 36. Release the six retaining tabs and remove the relay box under cover. BOX RETAINING TABS (6) 2-PIN RIGHT 5 x 12 mm SELF-TAPPING SCREW SCREW 2225140T BOX UNDER 2221030T 37. Lift the air cleaner housing cover up, and route the other end of the fog light harness toward the engine alongside the vehicle harness. 34. Remove the two bolts that fasten the relay box. BOX BOLTS Lift BOLT AIR CLEANER HOUSING BOLT (Remove.) 2213023T AIR CLEANER HOUSING 2226020T 35. Remove the one bolts that fasten the air cleaner housing cover. 2002 American Honda Motor Co., Inc - All Rights Reserved. AII 24050 (0208) 9 of 19
38. Unplug the vehicle 14-pin and 20-pin connectors from the relay box. Release the lock on the vehicle 14-pin connector, and push the fog light harness white/green and red/green wire terminals into the vehicle 14-pin connector. Reattach the lock on the 14-pin connector. 41. Secure the fog light harness to the vehicle harness with one wire tie in the area shown. BOX BOX UNDER 14-PIN BOX 20-PIN 14-PIN LOCK BOX RED/GREEN TERMINAL Harness WHITE/ side GREEN view TERMINAL As viewed from back side BLUE/RED TERMINAL LOCK Harness side view 20-PIN 42. Reinstall the relay box under cover. Be careful not to pinch the wires. 43. Under the relay box, locate the vehicle 3-pin connector blue-taped to the vehicle harness, and remove the blue tape to free the connector. Connect the fog light harness 3-pin connector into the 3-pin connector you just freed. Secure the fog light harness to the vehicle harness with one wire ties in the area shown. A/T Model BOX BLUE- TAPE (Remove.) 3-PIN 2226040T 14-PIN 20-PIN TERMINALS (3) 2226032T WIRE TIE 39. Release the lock on the vehicle 20-pin connector, and push the fog light harness blue/red wire terminal to the vehicle 20-pin connector. Reattach the lock on the 20-pin connector. 40. Plug the vehicle 14-pin and 20-pin connectors into the relay box. 3-PIN 2226053T 10 of 19 AII 24050 (0208) 2002 American Honda Motor Co., Inc - All Rights Reserved.
M/T Model 44. Install the relays (black and gray) to the relay bracket with two washer-bolts. 3-PIN BOX BLUE- TAPE (Remove.) WASHER- BOLT BRACKET (Fold back.) 3-PIN 2226063T NOTE: If the 3-pin connector is already being used by another accessory, locate the 3-pin connector taped to that other accessory's harness. Remove the tape and dummy connector from that other accessory's harness. Plug the fog light harness 3-pin connector into that other accessory's harness. 45. Plug the two fog light harness 4-pin connectors into the relays. L4 Engine Model BRACKET (If equipped) (BLACK) MOUNTING BOLT (Reuse.) (GRAY) 2222011T OTHER ACCESSORY 3-PIN 3-PIN 3-PIN BRACKET (BLACK) WIRE TIE 4-PIN (BROWN) (GRAY) 4-PIN (BLUE) OTHER ACCESSORY 3-PIN 2222021T 46. If equipped, remove the mounting bolt that secures the vehicle bracket, and attach the relay bracket with this bolt. 2215051T 2002 American Honda Motor Co., Inc - All Rights Reserved. AII 24050 (0208) 11 of 19
On V6 model, install the relay bracket to the vehicle frame with the washer-bolt supplied. V6 Engine Model 48. Secure the fog light harness to the vehicle harness with three wire ties in the areas shown. WASHER-BOLT FRAME BRACKET (BLACK) 4-PIN OF FOG LIGHT (BROWN) (GRAY) 4-PIN OF FOG LIGHT (BLUE) 2319011T 2226082T 47. If the vehicle harness is routed near a vehicle 4-pin connector, secure the fog light harness to the vehicle harness with one wire tie. 49. Remove the relay box cover (four retaining tabs), and install the 20A fuse (provided) into the No.10 slot of the relay box. BOX RETAINING TABS (4) FUSE (20A) FUSE (20A) BOX BOX 2319021T 2226071T 12 of 19 AII 24050 (0208) 2002 American Honda Motor Co., Inc - All Rights Reserved.
50. Attach the 20A fuse label over the No.10 spot of the relay box cover. Reinstall the relay box cover. 52. If equipped, remove the driver s dashboard under cover (the three clips, one pin and one holder). FUSE LABEL (20A) BOX LID HOLDER No.10 2319030T Routing the Switch Harness 51. Remove the driver s dashboard lower cover: Remove the one self-tapping screw. Release the four clips on the left side first by pulling out on the driver's dashboard lower cover. After releasing the four clips, insert the flat-tip screwdriver between the clip and the dashboard frame. Gently twist the screwdriver to release the clip. Release the two clips on the right side last. Unplug the vehicle connector, and remove the lower cover. CLIP (Release these clips first.) CLIPS (3) DRIVER S DASHBOARD UNDER PIN 53. Plug the switch harness 6-pin connector into the 6- pin connector of the fuse box. 6-PIN 2205020T CLIP (Release these clips last.) CLIPS (7) DRIVER S DASHBOARD LOWER SELF- TAPPING SCREW FRAME FLAT-TIP SCREWDRIVER 2206122K CLIP (Release the clip by inserting the flattip screwdriver between the clip and the dashboard frame, and twist the screwdriver to release the clip.) Front view 6-PIN FUSE BOX 2228011T 2002 American Honda Motor Co., Inc - All Rights Reserved. AII 24050 (0208) 13 of 19
NOTE: If the fuse box 6-pin connector is already being used by another accessory, unplug its 6-pin connector from the fuse box. Locate the 6-pin connector taped to the switch harness. Remove the dummy connector from switch harness. Plug the other accessory's harness 6-pin into switch harness, and plug the switch harness 6-pin connector into the fuse box. 55. Behind the steering hanger pipe, locate the 2-pin connector blue-taped to the vehicle harness. Connect the switch harness 2-pin connector to the vehicle 2-pin connector. 2-PIN STEERING HANGER PIPE 6-PIN DUMMY OTHER ACCESSORY 6-PIN 2-PIN FUSE BOX 54. Route the switch harness 5-pin connector (blue) to the body panel opening alongside the vehicle harness. Secure the switch harness to the vehicle harness (if equipped) with one wire tie in the area shown. BODY PANEL OPENING 2228021T NOTE: If the 2-pin connector is already being used by another accessory, locate the 2-pin connector taped to that other accessory's harness. Plug the switch harness 2-pin connector into the other accessory's harness. 2-PIN OF OTHER ACCESSORY 2-PIN 2228041T 5-PIN (Blue) (if equipped) 2-PIN 2308041T 2228030T 14 of 19 AII 24050 (0208) 2002 American Honda Motor Co., Inc - All Rights Reserved.
56. Attach the switch harness ground terminal to the steering hanger pipe stay with one of the ground bolt supplied. Without Cruise Control Unit 57. On the left of the steering shaft, locate the 3-pin connector black-taped to the vehicle harness, and plug the switch harness 3-pin connector in the 3-pin connector. STAY 3-PIN STEERING SHAFT GROUND TERMINAL OF GROUND BOLT 2507010T 3-PIN 2228072T With the Cruise Control Unit Remove and discard the bolt that fastens the control unit, then attach the switch harness ground terminal to the steering hanger pipe with the ground bolt supplied. NOTE: If the 3-pin connector is already being used by another accessory, locate the 3-pin connector taped to the other accessory's harness. Remove the dummy connector from the other accessory's harness. Plug the switch harness 3-pin connector into the other accessory's harness. CRUISE CONTROL UNIT 3-PIN STAY BOLT (Discard) GROUND BOLT GROUND TERMINAL 2507020T DUMMY OTHER ACCESSORY 3-PIN 2228082T 2002 American Honda Motor Co., Inc - All Rights Reserved. AII 24050 (0208) 15 of 19
58. Secure the switch harness to the vehicle harness with six wire ties in the areas shown. 60. If equipped, reinstall the driver's dashboard under cover. HOLDER 2228092T CLIPS (3) DRIVER S DASHBOARD UNDER PIN 2205020T 59. Remove the switch cover from the driver s side dashboard lower cover, and install the switch in the driver's dashboard lower cover. 61. Plug the switch harness 5-pin connector (blue) into the switch, then reinstall the dashboard lower cover. HOLE 5-PIN OF LID DRIVER'S DASHBOARD LOWER 2225160T DRIVER'S DASHBOARD LOWER 2225170T 16 of 19 AII 24050 (0208) 2002 American Honda Motor Co., Inc - All Rights Reserved.
62. Check that all wire harnesses are routed properly and all connectors are plugged in. 63. Reinstall all removed parts. Check that all clips and fasteners are installed securely. 64. Reconnect the negative cable to the battery. USE AND CARE How to Operate Fog Lights Turn the light switch to the on position (headlights on low beam ). Press the fog light switch (indicator is on). 66. Reset the clock, and reset the radio station presets. NOTE: Whenever the battery is disconnected, the driver s window AUTO function is disabled. 67. Start the engine. Push down on the driver s window switch until the window is fully open. 68. Pull up on the driver s window switch to close the window completely, then hold the switch for 2 seconds. 69. Test the driver's window AUTO function. The fog light lenses can cloud when the outside temperature is cold; this is normal and should go away in warm weather. Fog Light Aiming Adjustment 65. Adjust the fog light: Adjust the aiming according to local laws and regulations. To adjust, turn the aiming adjustment screw in or out until the correct aiming is obtained. To lower To raise PHILLlPS SCREWDRIVER AIMING ADJUSTMENT GEAR PHILLlPS SCREWDRIVER 2222031T 2002 American Honda Motor Co., Inc - All Rights Reserved. AII 24050 (0208) 17 of 19
BULB REPLACEMENT 1. Open the screw covers, remove the two selftapping screws that fasten the fog light, and pull the fog light out toward you. 2. Unplug the connector from the fog light, and remove the fog light assembly. 4. Install the new bulb into the socket. Use only a genuine Honda halogen light bulb of specified wattage. Rating: 12V 55W H11 Halogen Light Bulb P/N 33165-S5A-003 Do not touch the bulb. Oily or greasy substances on the bulb can shorten its service life due to the heat produced when the bulb is turned on. If the bulb is accidentally touched, wipe it clean with a soft cloth that has been dampened with a denatured alcohol or a mind detergent solution. Align the tab on the fog light with the cutout in the bulb when installing the new bulb. If not aligned, the fog light may annoy oncoming drivers. SCREW SELF-TAPPING SCREW 2225150T 3. Remove the bulb. NEW BULB SOCKET 2221050T BULB 2221040T 5. Reinstall the removed parts in the reverse order of removal. Check that the wire harnesses are not pinched. Be sure to tighten the self-tapping screw and bolts securely. 6. Check the operation of the fog light; adjust the aiming, if necessary. 18 of 19 AII 24050 (0208) 2002 American Honda Motor Co., Inc - All Rights Reserved.
CIRCUIT DIAGRAM Under-hood Relay Box HOT WITH HEADLIGHT IN HEAD HAED,AND DIMMER IN HIGH WHT/GRN FR HOT WITH HEADLIGHT IN HAED HEAD HOT AT ALL TIMES Fog Light Fuse 20A RED/GRN BLU/RED HOT WITH HEADLIGHT IN PARK OR HEAD Relay RED/BLK BLU 2 1 Switch 1=Indicator 2=Switch Illumination RED Illumination Control GRN BLK Relay BLU/YEL Front Fog Light BLK BLK BLK BLK OFF BLK BLACK BRN BROWN YEL YELLOW ORN ORANGE OFF LIGHT Low Hi BLU BLUE PUR PURPLE GRN GREEN NAT NATURAL RED RED PNK PINK WHT WHITE GRY GRAY OFF ON - - - - - - ON - LT BLU LIGHT BLUE LT GRN LIGHT GREEN 2002 American Honda Motor Co., Inc - All Rights Reserved. AII 24050 (0208) 19 of 19 2604010T