Instructions for the following part no s: 8280, 8279, 8282, 8283, 8284, 8273, 8274, 8275, & 8277 These instructions are for installation of the Super Kit, complete transmission, or rebuild kit for EVO or Twin Cam. These instructions are also reference for disassembly. Disassembly is the same as assembly, but in reverse order. READ ALL INSTRUCTIONS BEFORE PERFORMING WORK! IF YOU DO NOT KNOW WHAT YOU ARE DOING, DO NOT DO IT! JIMS IS NOT RESPONSIBLE FOR THE QUALITY AND SAFETY OF YOUR WORK! If you are not sure about any of the procedures in these instructions, have a reputable H-D repair shop perform these procedures for you. WARNING: Always disconnect the battery ground cable (at the battery) to prevent injury. Your work area should be well lit. Wear safety glasses (over your eyes) and protective clothing when working around power tools and compressed air. Be careful with chemicals when cleaning parts. Protect your skin from solvents and use only in a well-ventilated area. Degreasers are flammable and are a fire hazard. Just use common sense and exercise good judgement. If you have purchased a No.8277 FAT-5 Rebuilt Kit read these complete instructions before performing any work. See page 13 of these instructions for a Parts List of items included in this kit. 555 Dawson Drive, Camarillo, CA 93012 Phone 805-482-6913 Fax 805-482-9224 1
Instructions for preparing the Transmission Case to install JIMS Fat 5 Super Kit: Refer to your Service Manual and parts book for the proper year and model you will be installing this kit into for reference. Also, use a Late H-D 2002-05 Big Twin Service Manual and parts book for reference. 1. Remove Old Gear set and all Case Bearings per H-D Service Manual. NOTE: If Dowel Pin H-D No. 634 came out upon the Gear Set removal, it will need to be reinstalled back into the Trans Case. Refer to your H-D Service Manual. 2. Upgrade Shifter Shaft Bushing for 1990-99 Big Twins and 1999-2000 T/C FLHT, FXR & FXD by removing +.50 Over Stock the existing Shifter Shaft Bushing and installing a new longer Shifter Shaft Bushing H-D No.34979-00, JIMS No. 7514 (supplied). Follow the instruction Sheet provided with JIMS Tool No.1664 (not included) and refer to any 2000 to 2005 B.T. H-D Service Manual for Shifter Shaft Assembly. 3. Using masking tape, cover all the trap door flat holes except for the top three. The two threaded holes at the top of the trap door flange are used for mounting of the drill plate and the shift fork shaft hole (center through hole) is used as the pilot for the drill bits. 4. From inside the transmission case, tape over all bores as follows: Vehicle speed sensor and mounting screw bores Transmission top cover and shifter drum support screw bores Transmission drain hole bore Main Drive gear bearing bore Countershaft needle bearing bore Shift Fork shaft bore Shifter shaft bore Warning: Be sure drill plate is properly oriented before drilling. Improper orientation will result in damage that requires replacement of the transmission case. Special Tools Required to un-install JIMS Fat 5 Super Kit: Note: Some tools are the same as any 5 speed installation tools you might already have. Part No. Description 1077 Door Puller 35316-80 5-speed Maindrive Gear Tool 34902-84 Mainshaft Bearing Race Tool 94660-37A Mainshaft Sprocket Locknut Wrench 38515-90 Clutch Spring Compressor Tool 1990-1997 2260 Big Twin Sprocket Locker 2362 External Lock Ring Pliers 2234 Primary drive Locking Tool 1720 5-speed Main Bearing Remover 2189 Main and Counter Shaft Installer Solvent 184 (Valco) 1080 Brass Hammer 1145 Modular Engine & Transmission Stand Kit 555 Dawson Drive, Camarillo, CA 93012 Phone 805-482-6913 Fax 805-482-9224 2
4. Fasten drill plate, JIMS No.8357 to the top of the trap door flange using old and new speed sensor mounting screws as shown in Figure 1. 5. Spread one or two clean shop cloths inside the trans case to catch the metal shavings and debris. 6. Starting with a 3/8-inch drill bit, alternately use progressively larger bits to enlarge the fork shaft hole. Finish the drilling operation with a 3/4-inch drill bit. 7. Remove all remaining material up to the edge of the drill plate with a die grinder or similar tool. Remove the drill plate once complete. 8. Using emery cloth, steel wool, or a fine tooth file; remove any burrs or ridges that may exist from the drilling or cutting operations. Warning: Abrasive particles can damage machined surfaces and result in premature failure. 9. Carefully pull out shop cloths from inside the trans case. Exercise care to keep any debris captured by the cloths from falling into the trans case. 10. Place drain pan beneath trans case and remove tape from drain hole. Thoroughly flush the trans case with a non-volatile cleaning solution or solvent to remove any metal shavings, dust or debris that might remain. For best results, use a squirt bottle to direct a stream of solvent through the trans top cover opening. Repeat procedure as necessary draining excess solvent through the drain hole using low-pressure compressed air to thoroughly blow out all solvent. 11. Using a clean lightly oiled cloth, thoroughly wipe the Inside of FIGURE 1 the transmission case. Repeat this step with a new cloth until the cloth comes out clean. 12. Carefully inspect the transmission case for any metal shavings or debris. Repeat step 11 if any debris is found. 13. Remove the masking tape to uncover remaining holes and bores. Optional parts that may be needed to install JIMS Fat 5 Super Kit: Part No. Description 8102/8103 Billet speedo block off plate 8042K Speedo Block-Off Plate (Depending on application) 1708 Mega Nut 8126 Speedo Re-Calibration Module (Depending on year, pulley & tire size) 8080 Oil Spout Spacer, 2002 to 2006 FLH 14. Thoroughly inspect each bore for any metal shavings, dust or debris. Alternately direct com pressed air into each bore to be certain that it is clean and dry. 555 Dawson Drive, Camarillo, CA 93012 Phone 805-482-6913 Fax 805-482-9224 3
INSTRUCTIONS FOR PREPARING THE TRANSMISSION TOP COVER TO CLEAR THE NEW SHIFTING LEVER WHEN INSTALLING JIMS FAT 5 SUPER KIT INTO ANY 1990-99 BIG TWINS AND 1999-2000 T/C FLHT, FXR & FXD MODELS: NOTE: 2000-2006 FXST and 2001-2006 FLHT & FXD models do not need modifying. 1. Place new top cover gasket JIMS No.34904-86 on the trans top cover flange. 2. Use 4 of your top cover screws to hold gasket in place by slipping screws thru the gasket and into the top cover. 3. Mark the inside exposed portion of the flange as shown in Figure 2. The material to be removed is.060 wide by 1.80 Deep. Remove top cover screws and gasket. 4. With a die grinder tool, remove the casting rib until it is the same height as the adjacent surface area. Clean the top cover of all loose material, including screw holes as shown in Figure 2. 5. With shifter assembly installed in transmission; Install top cover with gasket using only 2 screws (so cover can move if shifter arm is making contact with top cover). 6. While watching to see if the top cover moves forward, shift the transmission into first gear firmly holding the shift lever down. If there is no forward movement of the top cover, then the modification is complete. If any forward movement (of top cover) is observed, then more of the casting rib must be removed. Repeat Step 4 as necessary. Instructions for Installing JIMS Fat 5 Super Kit parts into case: 1. Install main drive gear bearing JIMS No. 8996 using JIMS Tool No. 35316-80. Follow the instruc tion, sheet provided with tool or refer to your H-D FIGURE 2 Service Manual. NOTE: NEVER install any bearings into the case by applying pressure to the inner race. Doing so will destroy the bearing. Do not remove the mainshaft protective cover (Figure 4) on the clutch hub spline end of mainshaft. It can be removed after Super Kit has been installed into the trans case. 2. Install the new main drive gear retaining ring, JIMS No. 11061 (supplied) with the bevel facing out. Refer to your H-D Service Manual. 3. Install new main seal JIMS No.12067A (supplied) with JIMS Tool No. 95660-85 to use with JIMS Tool No. 95660-42. Refer to your H-D Service Manual. 4. Install main drive gear JIMS No. 8339-2, using JIMS Tool No. 35316-80. Follow the instruction sheet provided with tool or refer to your H-D Service Manual. 555 Dawson Drive, Camarillo, CA 93012 Phone 805-482-6913 Fax 805-482-9224 4
FIGURE 3 Tool No.2256-2 SHIFT FORK #8348 3rd GEAR SHIFT FORK #8349 4th-5TH GEAR SHOWN WITH CAP & SHRINK-WRAP FIGURE 4 5. Install counter shaft end bearing JIMS No. 8977. Refer to your H-D Service Manual. NOTE: Install counter shaft bearing by applying pressure to the LETTER side of bearing ONLY. 6. Install shifter shaft seal JIMS No. 12045 (supplied). Refer to your H-D Service Manual. 7. Install shifter assembly JIMS No. 8325 (supplied). Refer to your Late H-D Service Manual. 8. Install shifter shaft washer JIMS No. 6497HW and retaining ring JIMS No. 11150 (supplied). Refer to your late H-D Service Manual. 9. Install shifter shaft centering pin (BOLT) JIMS No. 34978-00A (supplied). Torque to 10 ft-lb. Refer to your Late H-D Service Manual. Caution: Center shifter assembly return spring on each side of centering bolt. NOTE: This model will not require any gear engagement adjustments. Refer to your Late H-D Service Manual. NOTE: 2 of the 3 shift forks will need to be installed into their shift rings as indicated in Figure 3. 10. Place 3rd gear fork, JIMS No. 8348 into 3rd gear shift ring, JIMS No. 8342 at the same time sliding both the fork and shift ring away from trap door so the fork will lay down towards countershaft as shown in Figure 3. 11. Place 4th gear fork, JIMS No. 8349 into 4th and 5th gear shift ring, JIMS No. 8354 at the same time allowing fork to lay down towards countershaft as shown in Figure 3. 555 Dawson Drive, Camarillo, CA 93012 Phone 805-482-6913 Fax 805-482-9224 5
Note: The last fork for 1st and 2nd gear, JIMS No. 8347, is installed after the Super Kit has been installed into case 12. Place trap door gasket JIMS No. 8352 over the two dowel pins on the trans case. Refer to your Late H-D Service Manual. 2 2 2 2 13. Apply a small amount of lube to the inside of the main drive gear. NOTE: If you have removed the mainshaft protective cover already, install a lubed tool JIMS No. 2256-2 main drive gear seal protector inside the main drive gear seal. The mainshaft protective sleeve covering the clutch hub spline on the mainshaft can also be used as a seal protector as the mainshaft is being installed thru the main drive gear as shown in Figure 4. 14.Gently place the gear set (trap door assembly) into the case by sliding the mainshaft through the main drive gear bearing and slowly pushing the trap door assembly inward until the trap door makes contact with the two dowel pins in trans case. A non-marring hammer is helpful to tap the trap door assembly over the dowel pins without risking damage to the aluminum/chrome of the trap door assembly. Apply a small amount of Blue Loctite to each of the four 1/4 screws, JIMS No. 1258 and thread them into the top four 1/4 screw holes. Torque to 84-108 in-lbs. in a crisscross pattern. Apply a small amount of Blue Loctite to each of the four 5/16 screws, JIMS No. 1118 and thread them into the four 5/16 screw holes. Torque to 13-16 ft-lbs in a criss-cross pattern as shown in Figure 5. 1 1 1 1. 5/16 in. screw @ 13-16 ft-lbs (17.6-21.7Nm) 2. 1/4 in. screw @ 84-108 in-lbs (9.5-12.2Nm) 1 FIGURE 5 Quad Seal No.11165 FIGURE 6 555 Dawson Drive, Camarillo, CA 93012 Phone 805-482-6913 Fax 805-482-9224 6
Instructions for installing the 1st and 2nd Gear Shift Fork JIMS No. 8347 1. Place the final remaining shift fork for the 1st and 2nd gear, JIMS No. 8347 into fork slot of 1st and 2nd shift ring, JIMS No. 8341 putting it down through the top cover opening and slide it into the shift ring. 2. Slide shift fork shaft, JIMS No. 34088-87 (supplied) through the hole in the trap door, all three shift forks and into the left side of trans case. Refer to your late H-D Service Manual. 3. Install shifter shaft set screw, JIMS No. 3784C (supplied). Tighten until you have about.020 end- play on the shifter shaft. No.33344-94 FIGURE 7 Instructions for Installing Main Seal Spacer and Torquing Mainshaft Nuts on Primary Side: 1. Slide all three shift rings so that they all three engage into mating gears (this is to lock the trans) to keep the gears from turning. 2. Install mainshaft quad seal, JIMS No. 11165 (supplied) over the main drive gear on left side of trans as shown in Figure 6. NOTE: Spacer 33344-94 is for late pulley only, pulley REF- ERENCE No. 40250-94A 3. Install mainshaft seal spacer JIMS No. 33344-94 (supplied) over mainshaft bearing boss on left side of trans, with the chamfered side to the inside towards seal as shown in Figures 7 and 8. 4. Install the drive pulley you will be using. Refer to your H-D Service Manual. 5. To install Mega Nut JIMS No. 1708 (not supplied) over the main drive gear. Follow instruction sheet supplied with Mega Nut. FIGURE 8 6. Install center pushrod, JIMS No. 37088-85 (supplied). Lube both ends and slide pushrod into Mainshaft. 7. Install primary drive, refer to your H-D Service Manual for the model your installing this kit into. 555 Dawson Drive, Camarillo, CA 93012 Phone 805-482-6913 Fax 805-482-9224 7
Instructions for installing shift drum, pillow blocks and top lid: 1. Place the shift drum assembly with pillow blocks over the 3 Pins of shift forks (you may need to move forks as needed to line up with the tracks in the shift drum). At the same time aligning the pillow blocks over and onto the 4 split dowel pins. Refer to your Late H-D Service Manual. 2. Install four 1/4 pillow block mounting washers, JIMS No. 1215 over the four 1/4 pillow block mounting screws, JIMS No. 2135. Apply a small amount of Blue Loctite to each screw and torque to 7-9 ft-lbs. in a criss-cross pattern. Refer to your late H-D Service Manual. 3. Install top cover gasket; JIMS No. 34904-86 (supplied) per your H-D Service Manual. 4. Install your top cover (Lid) with your mounting hardware; refer to your H-D Service Manual. 5. Install vent hose, H-D part No. 42533-91A (not supplied) to your top cover elbow fitting. Refer to your H-D Service Manual. Instructions for installing end cover: 1. Install right push rod for clutch; JIMS No. 8076 (supplied). 2. Install end cover, JIMS No. 8329 (supplied) with gasket JIMS No. 8352 (supplied). Refer to your H-D Service Manual. 3. Install speed sensor into trap door if applicable. NOTE: If you will be running an electronic speed sensor you will need to place a sensor cover, (see special parts list) over your sensor hole in trans case and install your electronic speed sensor into the trap door. If you will not be using an electronic speed sensor in either location (trap door or case) you will need to order a speed sensor block-off plate for the trap door. 4. Install speedo block-off plate, JIMS No.8042K or No.8102/8103 Billet block off plate. 5. Install speedo block-off plate mounting screw, JIMS No. 1120 by applying a small amount of Blue Loctite to screw and torque to 7-9 ft-lbs. 6. Fill trans with H-D trans lube or equivalent, to the same level as a 5 speed trans. Refer to your H-D Service Manual for reference. In the unlikely event that you would need to disassemble this trans, you will need a few of JIMS Service Tools. For replacement parts, see materials list on page 10. WARNING: Always disconnect the battery ground cable (at the battery) to prevent injury. Instructions for disassembly of your Fat 5 Speed Overdrive: This kit is basically easy to disassemble, but does require some special tools (See tool list on page 2.) 1. Remove primary and clutch components as indicated in your H-D Service Manual. 555 Dawson Drive, Camarillo, CA 93012 Phone 805-482-6913 Fax 805-482-9224 8
2. Drain oil from trans by removing drain plug from trap door, JIMS No. 739A (or if your trans case has other means of oil drain use that.) 3. Remove end cover. Refer to your H-D service manual. 4. Remove top cover and shift drum; slide all three forks into any gear (this is to lock the trans), to keep the gears from turning for removal of mainshaft and counter shaft nuts. 5. Remove shifter shaft set screw, JIMS No. 3784C. 6. Remove shifter shaft, JIMS No. 34088-87. 7. Remove 1st and 2nd gear shift fork JIMS No. 8347. 8. Remove all trap door hardware holding door to trans case. 9. Slide the 3rd gear shift fork & shift ring and 4th-5th gear shift fork & shift ring away from the trap door so that the forks will lay down towards the countershaft. (As shown in Figure 3) 10. Install trap door puller Tool, JIMS No. 1077 by lubing all threads of tool and threading trap door puller tool onto trap door. 11. Remove trap door slowly making sure shift forks clear case. 12. Remove both trap door bearings as you would for any 5-speed rebuild. 13. Remove all gears from main and counter shafts as you would for any 5-Speed trans following the parts list as laid out in this instruction sheet. 14. Remove any other parts, (bearings and seals) from trans case as you would for any 5-Speed. 15. To service main drive gear, use JIMS tool No. 37842-91. EXHAUST MOUNTING BRACKET MODIFICATION: You will most likely need to modify the original exhaust mounting bracket as needed. This will vary per model ( FL, FXD, or FXST ) and manufacturer of exhaust as needed. Mount exhaust to the bottom 2 or 4, 5/16 door mounting screws. FLH OIL FILL SPOUT MODIFICATION: 1. Super kits used on FLH models will need modification of oil fill spout cover to fit properly on transmission case. You will need to provide clearance on your fill spout to clear the trap door. You will need to machine, file, or grind to get enough clearance. This is so you can mount spout cover to the case in normal position without the cover touching the trap door. 2. On 2001 and earlier FLH models: Mount the modified oil fill spout to trans case along with oil fill spout gasket JIMS No. 866 (provided). Mount and torque four mounting screws per H-D. Service Manual. 3. On 2002 to present FLH models: Along with performing instruction steps above you need to purchase or make a spout spacer (not provided). For a spout spacer, order JIMS No.8088. You will need to plug and relocate the vent fitting on the spout cover as needed to clear your speedo sensor. 555 Dawson Drive, Camarillo, CA 93012 Phone 805-482-6913 Fax 805-482-9224 9
Parts list for Super Kits and reference for Transmission Assemblies. See drawings on page 11 and 12 for item bubble call outs. For No. 8277 Rebuild Kit parts list see page 13 Parts List: No. Qty Part No. Description 1 1 8325 Shift Lever, w/springs 2 1 8326 Screw, Adjuster, Clutch Hub 3 3 8873* Ball Bearing, Ramp 4 1 8876A Split Bearing, Mainshaft & Countershaft 5 1 8327 Trap Door, Fat 5 6 1 8343-1 Spline Sleeve, 4th & 5th, mainshaft 7 1 8329 End Cover, Chrome, Fat 5 8 1 8330-1 Mainshaft, Fat 5 9 1 8331-1 Countershaft W/5th Gear 10 2 8081 Thrust Washer, Mainshaft & Countershaft 11 1 8332-1 Gear, 2nd, Mainshaft 12 1 8333-1 Gear, 1st, Countershaft 13 4 8334-1 Gear, 1st, Mainshaft 14 1 8335-1 Gear, 2nd, Countershaft 15 1 8336-1 Gear, 3rd, Mainshaft 16 1 8337-1 Gear, 3rd, Countershaft 17 1 8338-1 Gear, 5th, Mainshaft 18 1 8339-2 Gear, 4th, Mainshaft 19 1 8340-1 Gear, 4th, Countershaft 20 1 8341-1 Shift ring, 1st & 2nd, Countershaft 21 1 8342-1 Shift Ring, 3rd, Mainshaft 22 1 8328-1 Spline Sleeve, 1st & 2nd, C/S 23 1 8344-1 Spline Sleeve, 3rd, M/S 24 2 35078-79 Locknut, Mainshaft & Countershaft 25 1 8996 Bearing, Main Case 26 2 8992 Bearing, Trap Door 27 5 11067 Retaining Ring 28 1 7514 Sleeve, Shifter Shaft (H-D No.34979-00) 29 1 34978-00A Centering Pin (8273 ONLY) 30 1 8076 Pushrod, Clutch, Right 31 1 8977 Crankshaft Bearing, Closed End 32 2 8345 Main Drive, Needle Bearing 33 4 1258 Screw, Upper Trap Door 34 4 1118 Screw, Upper Trap Door 36 1 8347 Shift Fork, 1st & 2nd Gear 37 1 8348 Shift Fork, 3rd Gear 38 1 8349 Shift Fork, 4th & 5th Gear 39 1 12067A Seal, Main Case 40 1 34088-87 Shaft, Shift Fork *NOT INCLUDED IN SUPER KITS. Parts List: No. Qty Part No. Description 41 1 8350 Shift Drum 42 1 8351 Gasket, End Cover 43 1 8352 Gasket, Trap Door, Stock Cover 44 4 8353 Bearing Pack, Mainshaft & Countershaft 45 1 34091-85 Bearing, Inner Race 46 1 6003 Thrust Washer 47 1 33904-00 Neutral Switch 48 1 8354 Shift Ring, 4th & 5th, Mainshaft 49 1 37088-85 Pushrod, Center 50 2 35087-99 Retaining Ring, Trap door 52 1 33376-00 Screw, Detent Arm 53 1 33374-00 Spring, Detent A rm 54 1 33375-00A Sleeve, Detent Arm Spring 55 1 33364-00A Detent Follower Assy 51 1 33304-00 Assy, Right Pillow Block 56 1 33301-00A Assy, Left Pillow Block, W/Bearing & Retainer 57 1 11342 Retainer, Shift Drum 58 4 2135 Screw, Pillow Block 59 1 34904-86 Gasket, Top Cover 60 1 25604-00* Ramp, Inner 61 1 25605-00* Ramp, Outer 62 1 10998 Retaining Ring 63 1 34920-86* Coupler Clutch 64 1 2226* Clutch Bearing 65 1 34977-02A Spring, Ratchet Arm 66 1 34064-00B Spring, Shifter 67 4 609 Roll Pin 68 1 72405-98TN Assembly, Tan Wire 69 1 72405-98BK Assembly, Black Wire 70 1 72241-94A Terminal, 1/4 Ring, 14-18 GA. 71 1 70585-93 Connector (18-20) 72 6 1121 Screw, Chrome 73 1 12045 Seal, Shifter 74 1 6497H Washer, Shifter 75 1 11150 Retaining Ring, Shifter 76 1 12035B Seal, Gear, Main Drive 78 6 8356 Pin, Drum 79 1 11165 Quad Seal 80 1 739A Drain Plug, Magnetic 81 1 3784C Plug, Shifter Shaft 82 1 11161 Retaining Ring, Main Drive Gear 83 1 37075-87 Dipstick With O-Ring #11132 88 1 8357 Tool, Modification, Case 89 4 1215 Washer, Pillow Block 90 1 8273-IS Instruction Sheet 555 Dawson Drive, Camarillo, CA 93012 Phone 805-482-6913 Fax 805-482-9224 10
Not used in Kit #8274 or #8275 (8273 ONLY) Not used in Kit #8274 or #8275 555 Dawson Drive, Camarillo, CA 93012 Phone 805-482-6913 Fax 805-482-9224 11
44 14 22 20 44 4 12 46 27 16 10 83 43 50 42 26 24 38 37 34 80 81 36 33 27 26 50 24 7 72 5 6 48 17 44 11 27 27 44 23 13 21 15 10 63 62 60 3 61 555 Dawson Drive, Camarillo, CA 93012 Phone 805-482-6913 Fax 805-482-9224 12
Parts list for Rebuild Kit No. 8277 for any Fat - 5 Transmissions. Item numbers may show where used on drawing bubble call out for reference on where used on pages 11 and 12. Some part numbers may not be shown in drawings. NO. QTY JIMS # Description 43 1 8352 GASKET, TRAPDOOR, FAT- 5 79 1 11165 QUAD SEAL, MAIN DRIVE SPACER 1 809 62423-90, GASKET, SPOUT, FXD 1 810 34917-90, GASKET, LID COVER, FXD 1 863 34917-99, GASKET, TOP LID, FXD 39 1 12067A SEAL MAINSHAFT 73 1 12045 SEAL, SHIFTER SHIFT 59 1 34904-86 GASKET, EARLY TRANS, TOP LID 1 867 34904-86C, GASKET, LATE TRANS TOP LID 76 1 12035B SEAL, MAINDRIVE GEAR 3 3 8873 BALL BEARING CLUTCH RAMP 4 1 8876A BEARING, M/S & C/S SPLIT 83 2 11132 O-RING, DIPSTICK, OR SPOUT 10 2 8081 THRUST WASHER 24 2 35078-79 C/S & M/S JAM NUTLOCK NUT 45 1 34091-85 RACE, MAINSHAFT 26 2 8992 BALL BEARING, TRAP DOOR 39 5 11067 RETAINING RING, M/S & C/S 31 1 8977 NEEDLE BEARING, C/S END 32 2 8345 BEARING, MAIN DRIVE GEAR 40 1 34088-87 SHIFT FORK SHAFT 44 4 8353 BEARING ASSY, SPLIT CAGE, M/S & C/S, FAT- 5 50 2 35087-99 RETAINING RING, TRAP DOOR BEARING 57 1 11342 RETAINING RING, SHIFT DRUM 62 1 10998 RETAINING RING, CLUTCH RAMP 64 1 2226 BEARING KIT, CLUTCH PUSHROD 66 1 34064-00C SPRING, SHIFTER SHAFT 82 1 11161 RETAINING RING, MAIN DRIVE CASE BEARING 25 1 8996 BEARING, MAIN DRIVE CASE 78 6 8356 DOWEL PIN, SHIFT DRUM 42 1 8351 GASKET, END COVER, FAT- 5 46 1 6003 THRUST WASHER, C/S 1 8041 GASKET SPEEDO COVER 1 11179 O-RING, CLUTCH CABLE 75 1 11150 RETAINER, SHIFTER SHAFT 1 811 62672-90, O-RING, LOWER SPOUT FXD 1 11289 O-RING, SPEEDO SENSOR 47 1 11290 O-RING, NEUTRAL SWITCH 555 Dawson Drive, Camarillo, CA 93012 Phone 805-482-6913 Fax 805-482-9224 13
Customer Support: For any installation on service or Questions, Please contact JIMS Technical Department @ (805)-482-6913 WARRANTY PROVISIONS All JIMS parts are guaranteed to the original purchaser to be free of manufacturing defects in materials and workmanship for a period of 12 (twelve) months from the date of purchase. Merchandise that fails to conform to these conditions will be repaired or replaced at JIMS option if the parts are returned to us by the purchaser within the 12 (twelve) month warranty period or within 10 (ten) days thereafter. In the event warranty service is required, the original purchaser must call or write JIMS immediately with the problem. Some problems can be rectified by a telephone call and need no further course of action. A part suspected of being defective must not be replaced by a Dealer without prior authorization from JIMS. If it is deemed necessary for JIMS to make an evaluation to determine whether the part is defective, it must be packaged properly to prevent further damage and be returned prepaid to JIMS with a copy of the original invoice of purchase and a detailed letter outlining the nature of the problem, how the part was used and the circumstances at the time of failure. If after an evaluation has been made by JIMS and the part was found to be defective, repair, replacement or credit will be granted. ADDITIONAL WARRANTY PROVISIONS 1. JIMS shall have no obligation in the event a JIMS part is modified by any other person or organization. 2. JIMS shall have no obligation if a JIMS part becomes defective in whole or in part as a result of improper installation, improper maintenance, improper use, abnormal operation, or any other misuse or mistreatment of the part. 3. JIMS shall not be liable for any consequential or incidental damages resulting from the failure of a JIMS part, the breach of any warranties, the failure to deliver, delay in delivery, delivery in non-conforming condition, or for any other breach of contract or duty between JIMS and a customer. 4. JIMS parts are designed exclusively for use in Harley-Davidson motorcycles. JIMS shall have no warranty or liability obligation if a JIMS part is used in any other application. DISCLAIMER The words Harley, H-D is a registered trademark and is for reference only. Use of H-D model designations and part numbers are for reference only. JIMS has no associations with, and makes no claims against, these words, trademarks, or companies. The installation of these parts may void or otherwise adversely affect your factory warranty. It is the sole responsibility of the user to determine the suitability of this product for his or her use, and the user shall assume all legal, personal injury risk and liability and all other obligations, duties and risks associated therewith. 555 Dawson Drive, Camarillo, CA 93012 Phone 805-482-6913 Fax 805-482-9224 14