RELOC Modular Wiring Specialty Lighting and Power Systems Family FileName Description RevisionDate Access Floor Wiring DB DB Distribution Box 10/15/1999 FM FMI3 Floor Module 03/15/2002 Power Wiring System CD CD Circuit Distributor 07/15/1997 CE CE Cable Extender 07/15/1997 CSU CSU Circuit Selector Unit 01/15/1996 DC DC Drop Cable 07/15/1998 PT PT Power Tee 10/15/2001 SS Series SS Splitter Splice 07/15/1997 SSC SSC Standard Selector Cable 01/15/1996 ST ST Switching Tee 01/15/1996
SPECIFICATIONS The Distribution Box is used as the interface between Reloc and hardwiring in access floor applications. The DB is located at the homerun location. From the DB, circuits are fed in different directions for service fittings or other access floor power devices. Pin-and-socket contacts Rated for use on 20-amp branch circuits All conductors are No. 12 AWG stranded copper with 90 o C thermoplastic insulation rated at 600V All components provide a fully-rated No. 12 AWG grounding conductor Available with up to twelve power ports. Up to three circuits per port, depending on system Safety-keying prevents accidental mismatching of components with different voltages Color-coding rapidly identifies system voltage Leads prestripped 5/8 for ease of wiring Isolated ground or two-circuit/two-neutral options available 1/2 trade-size knockouts on sides of box Additional labeling properly denotes type and position of each conductor UL listed; listed and labeled to comply with Canadian Standards Catalog Number Notes Reloc Wiring System DB Distribution Box ORDERING INFORMATION Example: DB 120 D 6CD 32 2N DB 120 Family DB Voltage 120 120V Number of conductors D Three E Four F Five 1 Distribution boxes requiring six to eight ports will be provided in an 8 x6 x4 box. More than eight ports will be provided in a 14 x 16 x 4.5 box. 2 Available only on the 14 x 16 x 4.5 box. Number of ports 4 Four 6 Six 8 Eight 1 12 Twelve 1 CD QC MR of port Circuit distributor Quickflex connector Modular regulator Options 2N Two circuits, two neutrals IG Isolated ground (2N and IG not available on the same DB) TB Terminal blocks 2 SL Standoff legs 2 Reloc Sheet #: DB POW-100
DB Distribution Box DIMENSIONS Dimensions are shown in inches. # of ports Width Length Height 1-6 6 " 6 " 3" 7-8 6 " 8 " 4" 9-14* 14" 16" 4.5" *Standoff legs included on this version. SYSTEM VIEW Sheet #: DB DB.P65 1990 Acuity Lighting Group, Inc., Rev. 10/99 Lithonia Lighting Acuity Lighting Group, Inc. Reloc Wiring Systems One Lithonia Way, Decatur, GA 30035 Phone: 800-241-4750 In Canada: 1100 50th Ave., Lachine, Quebec H8T 2V3 www.lithonia.com
Catalog Number FEATURES INTENDED USE The Reloc Floor Module provides separate compartments for data, communication and power in an access floor. When prewired with a RELOC interface, relocation of office work stations is as easy as moving partitions and floor panels. ATTRIBUTES Easy to install or relocate in any access floor. Concealed service top of sturdy molded Lexan. Wide access openings (two sizes). Easy entry into access floor. Hinged floor plate. Interchangeable faceplates for flexibility. 16-gauge galvanized steel. Up to 135 cubic inches capacity. Sturdy Lexan carpet/tile floor flange supports box on panel. Also acts as carpet flange. Available with factory-installed electrical devices and Reloc interface for wiring ease and flexibility. LISTING UL listed only. Notes Floor Module FMI3 For Use With Access Floor Power Distribution ORDERING INFORMATION Choose the boldface catalog nomenclature that best suits your needs and write it on the appropriate line. Order accessories as separate catalog number. Example: FMI3 P B RQ FMI3 Family 1 FM Size I1 5" X 6" (two compartments) I3 10" X 6" X 5-1/4" (Five compartments) Power options P One power panel for one duplex receptacle (receptacle not included) P1 One prewired 20A duplex receptacle (one circuit) P2 One prewired 20A isolated ground duplex receptacle (one circuit). Y Custom design 2 Data/communications options (blank) None provided D Blank panels Z Custom design 2 Color options B Black G Gray Reloc wiring interface options (blank) None RQ Reloc interface custom design 2 NOTES: 1 120V only. 2 Consult factory for custom design options. Reloc Sheet #: FMI3 POW-130
FMI3 Floor Module SPECIFICATIONS DIMENSIONS SHOWN IN INCHES AND (MILLIMETERS) DATA OPTIONS A 16-gauge pre-galvanized steel body and panels. B Two 1/2" K.O.s standard. C Carpet tile / floor flange colors available in gray, black and brown. NOTES: Self-drilling screws provided to secure FMI in place. Box will fit into 10 3/4" x 6 1/4" cutout in the floor panel. Box dimensions with trim: 12 3/8" x 7" x 5 1/2" SYSTEM VIEW Sheet #: FMI3 FMI3.P65 2002 Acuity Lighting Group, Inc., Rev. 03/02 Lithonia Lighting Acuity Lighting Group, Inc. Reloc Wiring Systems One Lithonia Way, Decatur, GA 30035 Phone: 800-241-4750 In Canada: 1100 50th Ave., Lachine, Quebec H8T 2V3 www.lithonia.com
FEATURES Pin and socket contacts. Rated for use on 20 amp branch circuits. Installed through standard 1/2" trade-sized knockout. All conductors are No. 12 AWG copper with 90 C thermoplastic insulation rated at 600V. All components provide a fully rated No. 12 AWG grounding conductor. Safety-keying prevents accidental mismatching of components with different voltages. Color-coding rapidly identifies system voltage. Additional labeling properly denotes type and position of each conductor. 6" leads are prestripped 5/8" for ease of wiring. Extremely low-profile. UL listed. Listed and labeled to comply with Canadian Standards. Catalog Number Notes Circuit Distributor CD APPLICATION The Circuit Distributor (CD) provides the interface between hardwiring and Reloc. Conventional wiring methods bring power from the panel to the homerun location where the CD is installed. RELOC Wiring Systems ORDERING INFORMATION The following information details the construction of a typical catalog number. Consult your RELOC sales representative for any special product needs. CD Example: CD 120 D 2N Series Voltage Number of Conductors Options 120 208 1 240 1 277 347 480 1 D E F Three Four Five add only if required 2N Two circuits, two neutrals IG Isolated ground Notes: 1. For use with 208, 240, 480 volts, consult factory. Reloc Sheet #: CD 820-100
CD Circuit Distributor SPECIFICATIONS DIMENSIONS SHOWN IN INCHES AND (MILLIMETERS) A Die-cast zinc with zinc-plated CRS cover B UL recognized connector body C Tin-plated copper contacts D Six-inch Leads prestripped 5/8" E Threaded nipple with locknut for easy installation in 1/2" tradesize K.O. SYSTEM VIEW Standard Version Sheet #: CD CD.P65 1996 Acuity Lighting Group, Inc., Rev. 7/97 Lithonia Lighting Acuity Lighting Group, Inc. Reloc Wiring Systems One Lithonia Way, Decatur, GA 30035 Phone: 800-241-4750 In Canada: 1100 50th Ave., Lachine, Quebec H8T 2V3 www.lithonia.com
FEATURES Pin and socket contacts. Rated for use on 20-amp branch circuits. All No. conductors are No. 12 AWG copper with 90 C thermoplastic insulation rated at 600V. All components provide a fully rated No. 12 AWG grounding conductor. Safety-keying prevents accidental mismatching of components with different voltages. Additional labeling properly denotes type and position of each conductor. Available in most lengths to suit job requirements. Auto-latching springs prevent accidental disengagement. UL listed. Listed and labeled to comply with Canadian Standards. Catalog Number... Notes Catalog number... Cable Extender CE APPLICATION The Cable Extender is a male/female cable that provides additional length anywhere throughout the Reloc system. The CE provides power to the ST to introduce local switching. The CE also provides power to the RCA, RCR, PT, SSU and CSU. RELOC Wiring Systems ORDERING INFORMATION The following information details the construction of a typical catalog number. Consult your RELOC sales representative for any special product needs. Example: CE 120 D U 3 2N CE U Series Voltage Number of Conductors Factory Keying Cable Length Options 120 208 1 240 1 277 347 480 1 D E F Three Four Five Available in lengths from 3 to 31 feet in two foot increments add only if required 2N Two circuits, two neutrals IG Isolated ground Notes: 1. For use with 208, 240, 480 volts. Consult factory. Reloc Sheet #: CE 820-110
CE Cable Extender SPECIFICATIONS DIMENSIONS SHOWN IN INCHES AND (MILLIMETERS) A Die-cast zinc with zinc-plated CRS cover B UL recognized connector body C Tin-plated copper contacts 1, 2 or 3 hot conductors in 120V and 277V as required. Rated for 20- amp capacity. Prefabricated Cable Extender carrying No. 12 AWG copper conductors rated at 600V, 90 C thermoplastic insulation and fully rated solid bare grounding conductor. SYSTEM VIEW Sheet #: CE CE.P65 1996 Acuity Lighting Group, Inc., Rev. 7/97 Lithonia Lighting Acuity Lighting Group, Inc. Reloc Wiring Systems One Lithonia Way, Decatur, GA 30035 Phone: 800-241-4750 In Canada: 1100 50th Ave., Lachine, Quebec H8T 2V3 www.lithonia.com
FEATURES Pin and socket contacts. Rated for use on 20-amp branch circuits. Snaps into standard 1/2" trade-size knockout no locknut required. All conductors are No. 12 AWG copper with 90 C thermoplastic insulation rated at 600V. All components provide a fully rated No. 12 AWG grounding conductor. Safety-keying prevents accidental mismatching of components with different voltages. Color-coding rapidly identifies system voltage. Additional labeling properly denotes type and position of each conductor. No. 12 AWG copper leads provided with poke-home connectors. Auto-latching springs prevent accidental disengagement. Male/female design allows removal without additional components. Extremely low-profile. UL listed, CSA Certified and IBEW union assembled. Catalog Number Catalog Number... Notes Catalog number... Circuit Selector Unit CSU APPLICATION The Circuit Selector Unit provides wiring of any device through a 1/2" trade-size knockout. The CSU used No. 12 AWG leads which allow for full circuit access. RELOC Wiring Systems ORDERING INFORMATION The following information details the construction of a typical catalog number. Consult your RELOC sales representative for any special product needs. Example: CSU 120 F U 2N CSU F U Series Voltage Number of Conductors Factory Keying Options 120 208 1 240 1 277 347 480 1 F Five add only if required 2N Two circuits, two neutrals IG Isolated ground Reloc Sheet #: CSU 820-150
CSU Circuit Selector Unit SPECIFICATIONS DIMENSIONS SHOWN IN INCHES AND (MILLIMETERS) A Die-cast zinc with zinc plated CRS cover B UL recognized connector body C Tin-plated copper contacts D Cast snap-in fitting 1/2" trade-size KO and provides gounding. E No. 12 AWG copper wires with 600V, 90 C thermoplastic insulation 4-5/8" (117.5) 2-3/16" (55.6) 1-7/16" (36.5) 9/16" (14.3) 1-1/16" (27.0) SYSTEM VIEW Sheet #: CSU csu.pdf 1996 Acuity Lighting Group, Inc., Rev. 01/96 Lithonia Lighting Acuity Lighting Group, Inc. Reloc Wiring Systems One Lithonia Way, Decatur, GA 30035 Phone: 800-241-4750 In Canada: 1100 50th Ave., Lachine, Quebec H8T 2V3 www.lithonia.com
SPECIFICATIONS The Drop Cable allows any convenience power outlet, switch or other device (clock, miscellaneous fixture, etc.) to become part of the Reloc system. The use of conventional pipe and wire is not required in these applications to convey the wiring. Pin-and-socket contacts Rated for use on 20-amp branch circuits All conductors are No. 12 AWG copper with 90 o C thermoplastic insulation rated at 600V All components provide a fully-rated No. 12 AWG grounding conductor Prestripped solid-copper leads for easy installation into side, back or push-in type terminals Safety-keying prevents accidental mismatching of components with different voltages Color-coding rapidly identifies system voltage Additional labeling properly denotes type and position of each conductor Available in most lengths to suit job requirements Auto-latching springs prevent accidental disengagement Installs through standard 1/2" trade-size knockout UL listed; listed and labeled to comply with Canadian Standards Catalog Number Notes Reloc Wiring System DC Drop Cable ORDERING INFORMATION Example: DC 120 D U 09 DC U Family DC Voltage 120 120V 208 208V * 240 240V * 277 277V 347 347V 480 480V * Number of conductors D Three E Four F Five Factory keying Cable length Available in lengths up to 31 in two-foot increments. 2N IG Options Two circuits, two neutrals Isolated ground *For use with 208, 240 and 480 volts. Consult factory. Reloc Sheet #: DC 820-170
DC Drop Cable DIMENSIONS Dimensions are shown in inches (millimeters). A 18-gauge, zinc-plated CRS cover B UL-recognized connector body C Tin-plated, copper contacts D.015 spring steel latches Prefabricated lighting drop cable assembly carrying No. 12 AWG standard copper conductors rated at 600V with 90 o C thermoplastic insulation and fully rated insulated grounding conductor D SYSTEM VIEW Sheet #: DC DC.P65 1990 Acuity Lighting Group, Inc., Rev. 7/98 Lithonia Lighting Acuity Lighting Group, Inc. Reloc Wiring Systems One Lithonia Way, Decatur, GA 30035 Phone: 800-241-4750 In Canada: 1100 50th Ave., Lachine, Quebec H8T 2V3 www.lithonia.com
SPECIFICATIONS The Power Tee is a through-wired component that makes it possible to select which branch circuit conductor feeds a specific device. The PT also provides power to devices used on convenience power, access floor systems and commercial lighting. Pin-and-socket contacts. Rated for use on 20-amp branch circuits. Replaces conventional cord and plug. All conductors are No. 12 AWG copper with 90 o C thermoplastic insulation rated at 600V. All components provide a fully-rated No. 12 AWG grounding conductor. Accommodates up to three hot conductors plus neutral and ground feed-through of branch circuits in a single component. Enables receptacle outlets or utilization equipment (e.g., exit signs) to become a part of the Reloc system. Prestripped solid-copper leads for easy installation into side, back or push-in type terminals. Safety-keying prevents accidental mismatching of components with different voltages Color-coding rapidly identifies system voltage Additional labeling properly denotes type and position of each conductor Male/female design allows removal of a device without additional components. Available in most lengths to suit job requirements Auto-latching springs prevent accidental disengagement Installs through standard 1/2" trade-size knockout UL listed; CSA Certified and IBEW union assembled. Catalog Number Notes Power Tee PT ORDERING INFORMATION PT Example: PT 120 F 1 A 01 2N Series Voltage 120 120V 277 277V 347 347V Number of conductors F Five Tap position 1 Tap from position one 2 Tap from position two 3 Tap from position three 12 Tap from position one and two 13 Tap from position one and three 23 Tap from position two and three 123 Tap from position one, two and three of drop A Armored Cable length 01 One foot 03 Three feet 09 Nine feet 2N IG Options Two circuits, two neutrals Isolated ground *For use with 208, 240 and 480 volts. Consult factory. Reloc Sheet #: PT 820-160
PT Power Tee DIMENSIONS Dimensions are shown in inches (millimeters). WIRING SCHEMATICS A Die-cast zinc with zinc-plated, cold-rolled steel cover B UL-recognized connector body C Tin-plated, copper contacts D No. 12 AWG wire with 600V, 90 o C thermoplastic insulation rated for 20-amp capacity SYSTEM VIEW Sheet #: PT PT.P65 2001 Acuity Lighting Group, Inc., Rev. 10/01 Lithonia Lighting Acuity Lighting Group, Inc. Reloc Wiring Systems One Lithonia Way, Decatur, GA 30035 Phone: 800-241-4750 In Canada: 1100 50th Ave., Lachine, Quebec H8T 2V3 www.lithonia.com
SPECIFICATIONS The Splitter Splice is used to split the branch circuit into two directions. The SS is a male/female component that allows it to be used anywhere throughout the Reloc system. Pin-and-socket contacts. Rated for use on 20-amp branch circuits. All conductors are No. 12 AWG copper with 90 o C thermoplastic insulation rated at 600V. All components provide a fully-rated No. 12 AWG grounding conductor. Capable of accommodating cable with up to three conductors. Safety-keying prevents accidental mismatching of components with different voltages. Additional labeling properly denotes type and position of each conductor. Listed and labeled to comply with Canadian Standards. Catalog Number Notes Industrial Wiring System SS Splitter Splice ORDERING INFORMATION SS F U Example: SS 120 F U Family SS Voltage 120 208* 240* 277 347 480* # of conductors F Five Factory keying U * For use with 208V, 240V and 480V; consult factory. Reloc Sheet #: SS 820-180
SS Splitter Splice DIMENSIONS Dimensions are inches (millimeters). WIRING SCHEMATICS A B C Die-cast zinc with zinc-plated CRS cover UL-recognized connector body Tin-plated copper contacts Prefabricated splice module carrying No. 12 AWG copper conductors rated at 600V, 90 C thermoplastic insulation and fully rated grounding conductor. SYSTEM VIEW Sheet #: SS SS.P65 1996 Acuity Lighting Group, Inc., Rev. 7/97 Lithonia Lighting Acuity Lighting Group, Inc. Reloc Wiring Systems One Lithonia Way, Decatur, GA 30035 Phone: 800-241-4750 In Canada: 1100 50th Ave., Lachine, Quebec H8T 2V3 www.lithonia.com
FEATURES Pin and socket contacts. Rated for use on 20-amp branch circuits. All conductors are No. 12 AWG copper with 90 C thermoplastic insulation rated at 600V. All components provide a fully rated No. 12 AWG grounding conductor. Fixture leads are No. 18 AWG solid copper, with poke-home terminals for easy connection to ballast leads. No wirenuts required. Safety-keying prevents accidental mismatching of components with different voltages. Color-coding rapidly identifies system voltage. Additional labeling properly denotes type and position of each conductor. Snaps into standard 1/2" trade-size knockout no locknut required. Designed with auto-grounding (fixture) mechanism standard. Available in varying lengths to suit most common fixture spacing requirements. UL listed, CSA Certified and IBEW union-assembled. Catalog Number Number... Notes Catalog number... Standard Selector Cable SSC APPLICATION The Standard Selector Cable is a male/female cable that provides power from fixture to fixture. The SSC attaches directly into the access plate or through any 1/2" trade-size knockout. RELOC Wiring Systems ORDERING INFORMATION The following information details the construction of a typical catalog number. Consult your RELOC sales representative for any special product needs. Example: SSC 120 D U 2N SSC U Series Voltage 120 277 347 Number of Conductors D Three E Four F Five Factory Keying Cable Length Available in lengths from 3 to 31 feet in two foot increments Options add only if required 2N Two circuits, two neutrals G Ground leads with lug terminal FP Factory pack selector cable equipped with prestripped leads to be wired into fixture by O.E.M. (length of cable limited to 13 feet) Reloc Sheet #: SSC 820-120
SSC Standard Selector Cable SPECIFICATIONS DIMENSIONS SHOWN IN INCHES AND (MILLIMETERS) DIMENSIONS A UL recognized connector body B Die-cast zinc with zinc-plated CRS cover C Tin plated copper contacts D Cast snap-in fitting fits 1/2" trade-size K.O. and provides grounding E No. 18 AWG solid copper wires rated at 600V, 90 C thermoplastic insulation with UL recognized poke-home terminals 1, 2 or 3 hot conductors in 120V and 277V as required. Prefabricated Standard Selector Cable carrying No. 12 AWG copper conductors. 600V, 90 C thermoplastic insulation and fully rated solid bare grounding conductor. Rated for 20-amp capacity. NOTE: Standard Selector Cable provides auto-grounding to fixture unless specified otherwise. Lengths of 19 feet or longer provide a ground drop as standard. SYSTEM VIEW Sheet #: SSC ssc.pdf 1996 Acuity Lighting Group, Inc., Rev. 1/96 Lithonia Lighting Acuity Lighting Group, Inc. Reloc Wiring Systems One Lithonia Way, Decatur, GA 30035 Phone: 800-241-4750 In Canada: 1100 50th Ave., Lachine, Quebec H8T 2V3 www.lithonia.com
FEATURES Pin and socket contacts. Rated for use on 20-amp branch circuits. All conductors are No. 12 AWG copper with 90 C thermoplastic insulation rated at 600V. All components provide a fully-rated No. 12 AWG grounding conductor. Enables switches to be completely wired into the Reloc system. Provides switched and unswitched power at every switch location. Located directly over switch. Prestripped, solid copper leads for easy installation into side, back or push-in type terminals on switches. Safety-keying prevents accidental mismatching of components with different voltages. Additional labeling properly denotes type and position of each conductor. Color-coding rapidly identifies system voltage. UL listed, CSA Certified and IBEW union-assembled. Catalog Number Number... Notes Catalog number... Switching Tee ST APPLICATION The Switching Tee, located above the primary switch location, introduces local switching to Reloc systems. It provides local switched power and unswitched power to be used as needed for subsequent fixtures. RELOC Wiring Systems ORDERING INFORMATION The following information details the construction of a typical catalog number. Consult your RELOC sales representative for any special product needs. Example: ST 120 D 1 P U 06 N ST P U Series Voltage 120 277 347 Number of Conductors D Three E Four F Not applicable Switching Function 1 Single level switching 2 Two level switching 3 Three-way switching (primary only) 4 Four-way switching Drop P Protected Factory Keying Cable Length 06 Six feet 08 Eight feet 15 Fifteen feet Options add only if required N 2N Neutral provided in drop Two circuits, two neutrals Reloc Sheet #: ST 820-140
ST Switching Tee SPECIFICATIONS DIMENSIONS SHOWN IN INCHES AND (MILLIMETERS) WIRING SCHEMATICS ST D2PU06 A UL recognized connector body B Tin plated copper contacts C No. 12 AWG wire rated at 600V 90 C thermoplastic insulation D Die-cast zinc with zinc-plated CRS cover Rated for 20-amp capacity ST E2PU06 SYSTEM VIEW Sheet #: ST st.pdf 1996 Acuity Lighting Group, Inc., Rev. 1/96 Lithonia Lighting Acuity Lighting Group, Inc. Reloc Wiring Systems One Lithonia Way, Decatur, GA 30035 Phone: 800-241-4750 In Canada: 1100 50th Ave., Lachine, Quebec H8T 2V3 www.lithonia.com