8100 Sweeney S/N STM014 1 107029435 BRKTs -3 Tooling 2 527241105 Fixture(combustion Chamber Fixture) 1 537241146 Fixture (combustion Chamber Fixture) 1 278114-1 CFM56-3 Fuel Pump Backlash Tool 1 301-360-005-0 Slave AGB Mount Links 1 305-356-605-0 Slave AGB Mount Links 1 856A1000 Wrench - No. 3 Bearing Locknut - Inst & Removal 2 856A1007 Supports 2 856A1008G02 FIXTURE LIFT & TURN 6 856A1009 Lifting Fixture 1 856A1011G07 PROTRACTOR VSV (KIT 2 CASES) 1 856A1016 Stand HPT Roror 2 856A1017 HPT Shroud Pullets 2 856A1018G03 Stand, Subassembly - Frames 1 856A1018G03 Stand, Subassembly - Frames 1 856A1020G09 Fixture - Restraining, Core Module - AFT 4 856A1021 Fixture 4 856A1022G01 WRENCH SET 10 856A1022G03 WRENCH SET 2 856A1023 Wrench 2 856A1025 Seal Wire locator 1 856A1026 Fixture 1 856A1027G01 Fixture, Lift - Compressor Rotor Stage 3 Disk And Blades 1 856A1028 Fixture 1 856A1029G01 Fixture, Lift - Compressor Rotor Stage 1-2 Spool, Forward 1 856A1033 Puller - No. 3 Bearing And Gear 1 856A1034G01 Wrench, 35-tooth Bevel Gear Locknut 1 856A1035G01 Fixture, Holding - No. 3 Bearing Igb Retainer Nut 1 856A1037G01 Wrench 1 856A1037G02 Wrench, Puller Ring - Igb Module 1 856A1038-2 Fixture, Installation - Igb Bearing And Spacer 1 856A1038G01 Fixture, Installation - Igb Bearing And Spacer 1 856A1039G01 Adapter Inlet Gearbox To Power Arm 1 856A1040G01 Fixture, Removal - Igb Bearing And Spacer 1 856A1040G01 Fixture, Removal - Igb Bearing And Spacer 1 856A1041 HPT Fixture + Spares 3 856A1042 WRENCH TORQUE NO. 4 BNG. 2 856A1042-6 WRENCH 1 856A1045G01 Wrench, No. 3 Bearing Retainer Bolt 1 856A1046-4 Wrench, No. 3 Bearing - Rotating Seal 1 856A1046-5 Wrench, No. 3 Bearing - Rotating Seal 1 856A1046-8 Wrench, No. 3 Bearing - Rotating Seal 1 856A1046G03 Wrench, No. 3 Bearing - Rotating Seal 1 856A1047G03 Fixture, Holding - Igb Module 1 856A1048G02 Table, Antitorque - Tooling Igb Module 1 O:\USERGRP\2014 Tasks\Tooling lists\cfm56-3 (FINAL_) 1 of 17 01/05/2014
856A1048G02 Table, Antitorque - Tooling Igb Module 856A1049G01 Puller, No. 3 Bearing - Inner Races 1 856A1050G02 Backlash Fixture 1 856a1050G03 Backlash Fixture 1 856A1051G01 Puller, Arm - Compressor Stator Actuation 1 856A1052 Fixture, Precision Build-up And Runout - HPT/ 2 856A1052 Fixture, Precision Build-up And Runout - HPtr 1 856A1052G02 Fixture, Precision Build-up And Runout - HPT 2 856A1052P21 Fixture Turn Table 1 856A1053 Oilflow Tool 2 856A1054G02 Tool Set 1 856A1057G03 LIFT & TURN FIXTURE 4 856A1058 Vibrator Gun (HPC Build) 1 856A1061G03 Fixture, Lift And Turn, Disk, Forward 1 856A1062 Fixture (Chilling) 1 856A1063 HPC installation Set 1 856A1069 Bracket, Trunnion - Combustion Case 1 856A1069 Bracket, Trunnion - Combustion Case 5 856A1069 Bracket, Trunnion - Combustion Case 1 856A1069 Bracket, Trunnion - Combustion Case 1 856A1069G02 Bracket, Trunnion - Combustion Case 1 856A1069G02 Bracket, Trunnion - Combustion Case 1 856A1069G02 Bracket, Trunnion - Combustion Case 4 856A1069G02 Bracket, Trunnion - Combustion Case 1 856A1069G02 Bracket, Trunnion - Combustion Case 1 856A1069G04 Bracket, Trunnion - Combustion Case 1 856A1069G04 Bracket, Trunnion - Combustion Case 1 856A1069G04 Bracket, Trunnion - Combustion Case 1 856A1069G04 Bracket, Trunnion - Combustion Case 4 856A1072G04 Truck, Compressor Rotor, Horizontal 2 856A1072G04 Truck, Compressor Rotor, Horizontal 1 856A1073 HPT Transport Fixture 1 856A1075 LIFT & TURN FIXTURE 2 856A1075G02 FIXTURE LIFT & TURN 1 856A1081 Core module HORZ Stand 2 856A1082G01 LIFT TOOL HPC ROTOR 4 856A1083 Fixture Lift/Turn 3 856A1084P17 Cart - Stator Actuator 856A1085G02 Bar, Lift And Turn - Main Engine Section 1 856A1085G02 LIFTER MAIN ENG 1 856A1085P02G02 Bar, Lift And Turn - Main Engine Section (Handle) 1 856A1085P03 LIFTER MAIN ENG 1 856A1087 Bracket Set, Handling - Compressor Mid Flange 2 856A1087 Bracket Set, Handling - Compressor Mid Flange 2 856A1088 Core Rotating Fixture 4 856A1089 Wrench ( HPT Nut) 6 856A1092 HPT Holding Fixture 1 856A1093 Lifting Fixture 1 O:\USERGRP\2014 Tasks\Tooling lists\cfm56-3 (FINAL_) 2 of 17 01/05/2014
856A1094 ADPT Power Arm 1 856A1095 HPT Fixture 2 856A1099 Fixture, Installation And Removal - HPT Aft Outer Air Seal 1 856A1100 Retainer Pin driver 1 856A1102 Lifting Fixture 1 856A1103 Lifting Fixture (HPT Nozzle ASSY) 1 856A1107G05 Ball-lock Pin 1 856A1107G07 Fixture, Lift - Core Module 3 856A1110G04 Stand, Installation - Front Compressor Stator Sector And Liner 1 856A1111 Install Fixture 1 856A1112G01 Stand, Installation - Rear C/S Sectors And Liners 1 856A1114 Bracket Support 1 856A1117 Lifting Fixture 2 856A1118G01 Gage Set, Seating - Igb Module To Compressor Rotor Shaft 1 856A1123 Guide - Fan Frame To Core Module 1 856A1125 Lifting Fixture 2 856A1126 Installation Tool 8 856A1126P03 Installation Tool 1 856A1126P04 Installation Tool 1 856A1126P05 Installation Tool 1 856A1126P06 Installation Tool 1 856A1127 Stud Protector 1 856A1130G10 ToolSet 2 856A1131G03 Fixture, B/U HPT Shroud LPT Stg1 1 856A1131G04 Fixture, B/U HPT Shroud LPT Stg1 1 856A1133 Remover, Blade Retainer - HPTR, Aft 1 856A1133 Remover, Blade Retainer - HPTR, Aft 1 856A1133 Remover, Blade Retainer - HPTR, Aft 1 856A1135 HPT Grind Fixture 2 856A1140 Core Fixture 3 856A1143G02 Fixture, Installation - Lp Nozzle Retaining Ring 2 856A1146 Inner Cooling Duct Tool 2 856A1147G01 Radial positional Tool 2 856A1148 Tool, Installation - HPT Shroud Stud 1 856A1154P02 Master Set Up 1 856A1155P05 Chuck Table 1 856A1155P06 Chuck Table 1 856A1156G01 pylon 2 856A1157 Lifting Fixture 2 856A1161 Arbor, Balance - High Pressure Turbine Rotor 1 856A1165G01 Sling, Lift - Compressor Rotor Assembly Or Stage 4-9 Spool 1 856A1166G02 Sling, Lift - HPT Balance And Grind 1 856A1177G01 Truck - HPC Rotor/HPT Rotor And Balance Arbors 1 856A1180G02 Fixture, Removal - HPT Stator/LPT Nozzle Module 2 856A1195G02 FIXTURE ASSY 1-2 FWD SHAFT 1 O:\USERGRP\2014 Tasks\Tooling lists\cfm56-3 (FINAL_) 3 of 17 01/05/2014
856A1198 HPT Pullers 1 856A1199 Bolt Retainer 3 856A1202 Shipping Stand 1 856A1204G01 FIXTURE REMOVAL 1 856A1206 Run Out Gauge 1 856A1212 HPC Measuring Kit 1 856A1213G01 Pin Set, Alignment-HPT Rotor Disk to Shaft 1 856A1213G01 Pin Set, Alignment-HPT Rotor Disk to Shaft 1 856A1216G02 PULLER NO.4 BNG. 2 856A1216P02 PULLER NO.4 BNG. 1 856A1219 Heater Duct 2 856A1225G01 Table Support 1 856A1240G01 Fixture, Installation - HP Turbine Stator/LP Turbine Stage 1 Nozzle 3 856A1245G01 Fixture, Clamping - Compressor Rotor 1 856A1245P03 Fixture, Clamping - Compressor Rotor (Part Of Tool) 1 856A1252G02 INSTALLATION PLIERS 1 856A1256 Liner Diameter Gauge 1 856A1257 Container, Shipping - Core 1 856A1259 Seating Check Gauge 1 856A1260 Inside Mic ( Inner Stage Seals) 1 856A1265G04 Core Heater 1 856A1266G03 Alignment Sets (74 Items) 2 Boxes 2 856A1275 Full Set of HPC GAUGES.PO2,03,04,05,06,07,08,09,10 1 856A1276 Erosion Gauge Set 1 856A1281G02 Fixture, Lift - HPT Front Outer Seal 1 856A1284 HPT Pin Pullers 1 856A1291P02 Fixture, Install & Remove - Inlet Gearbox Module 856A1291P02 Fixture, Install & Remove - Inlet Gearbox Module 856A1291P03 Fixture, Install & Remove - Inlet Gearbox Module 856A1291P04 Fixture, Install & Remove - Inlet Gearbox Module 856A1291P10 Fixture, Install & Remove - Inlet Gearbox Module 856A1291P13 Fixture, Install & Remove - Inlet Gearbox Module 856A1291P32 Fixture, Install & Remove - Inlet Gearbox Module 856A1291P35 Fixture, Install & Remove - Inlet Gearbox Module 856A1300G03 Gage, Length - Core Engine Module 1 856A1308 No 4 Outer airseal Pullers 1 856A1312-15 Support - Engine Handling 4 O:\USERGRP\2014 Tasks\Tooling lists\cfm56-3 (FINAL_) 4 of 17 01/05/2014
856A1312G02 Support - Engine Handling 44 856A1312G03 Support Engine Handling 26 3 856A1313G04 Ring, Support - Engine Handling 8 856A1313G04 Ring, Support - Engine Handling 8 856A1314G01 Bracket Set, Support - LP Turbine Aft Mount 12 856A1314G01 Bracket Set, Support - LP Turbine Aft Mount 1 856A1314G01 Bracket Set, Support - LP Turbine Aft Mount 1 856A1314G01 Bracket Set, Support - LP Turbine Aft Mount 1 856A1314G01 Bracket Set, Support - LP Turbine Aft Mount 1 856A1314G01 Bracket Set, Support - LP Turbine Aft Mount 1 856A1314G01 Bracket Set, Support - LP Turbine Aft Mount 1 856A1314G01 Bracket Set, Support - LP Turbine Aft Mount 1 856A1336G02 WRENCH 1 856A1354G02 Bracket Set, Handling - Compressor Mid-flange 14 856A1354G02 Bracket Set, Handling - Compressor Mid-flange 11 856A1356 Lift Fixture 1 856A1358 Fixture, Install/Remove - Module 12 (Just The Handle Present) 3 856A1378G01 Bolt Retainer Set, HPc Rotor To Cdp Seal To HPt Rotor 1 856A1380 Outer air duct pullers 1 856A1381 Puller outer Duct 1 856A1384 HPT Shroud Removal Tool 3 856A1418G03 Retainer, Shroud Hanger - HPT Stator 1 856A1439 Gage Id - Igv Inner Stage Seal 1 856A1471 LPT Support BRKT 2 856A1508G01 No 4 Brg Heater 1 856A1604G02 Fixture, Removal - Bolt Inner Nozzle Support 1 O:\USERGRP\2014 Tasks\Tooling lists\cfm56-3 (FINAL_) 5 of 17 01/05/2014
856A1820 Support Fixture 1 856A2005 Guide Fan Module 1 856A2010 Fixture (HPT Bolt Removal) 2 856A2474 Checking Tool (CVT) 1 856A2504G01 Push-pull, Ferrule - Vbv Flexible Shaft 1 856A2504P05 Push-pull, Ferrule - Vbv Flexible Shaft 1 856A2504P08 Push-pull, Ferrule - Vbv Flexible Shaft 1 856A2513P02 Tube, Dummy-LPT Shaft Forward End 3 856A2513P02 Tube, Dummy-LPT Shaft Forward End 1 856A2513P04 Tube, Dummy-LPT Shaft Forward End (Part Of Tool) 1 856A2513P09 TUBE DUMMY LPT 1 856A2513P11 TUBE DUMMY LPT 3 856A2516G01 Arm, Support, Baseplate, Mobile - Booster Stator 10 856A2516G01 Arm, Support, Baseplate, Mobile - Booster Stator 7 856A2516G01 Arm, Support, Baseplate, Mobile - Booster Stator 7 856A2521G02 Fixture, Alignment - Booster/LPT Shaft 1 856A2521G02 Fixture, Alignment - Booster/LPT Shaft 1 856A2521G02 Fixture, Alignment - Booster/LPT Shaft 1 856A2524 Fixture, Handling - LPT Major Module 1 856A2524 Fixture, Handling - LPT Major Module 1 856A2524G01 Fixture, Handling - LPT Major Module 1 856A2524G01 Fixture, Handling - LPT Major Module 1 856A2524G01 Fixture, Handling - LPT Major Module 1 856A2524G02 Fixture, Hoist - LPT Module 2 856A2525G01 Adapter, Sleeve - Booster Guide 2 856A2526G03 Guide, Alignment - LPT Shaft Or Booster To Fan Shaft 856A2526G03 Guide, Alignment - LPT Shaft Or Booster To Fan Shaft 856A2526G03 Guide, Alignment - LPT Shaft Or Booster To Fan Shaft 856A2526G03 Guide, Alignment - LPT Shaft Or Booster To Fan Shaft 856A2526G03 Guide, Alignment - LPT Shaft Or Booster To Fan Shaft 856A2526G03 Guide, Alignment - LPT Shaft Or Booster To Fan Shaft (P.O.T) 2 856A2526P20 Guide pins 4 856A2526P21 Guide Pins 8 856A2540 fixture lpt shaft build up 2 856A2542G02 Fixture, Hoist - LPT Module 1 856A2542G02 Fixture, Hoist - LPT Module 1 856A2542G02 Fixture, Hoist - LPT Module 1 856A2542G02 Fixture, Hoist - LPT Module 1 856A2542G02 Fixture, Hoist - LPT Module 1 856A2542G02 Fixture, Hoist - LPT Module 1 856A2542G02 Fixture, Hoist - LPT Module 1 856A2543 LPT Centering Fixture 7 O:\USERGRP\2014 Tasks\Tooling lists\cfm56-3 (FINAL_) 6 of 17 01/05/2014
856A2544G02 Dolly Trunnion- Turbine Frame Module 4 856A2544G02 Dolly Trunnion - Turbine Frame Module 4 856A2548 storage fixture lpt shaft module 6 856A2549 SEGMENTS HANDLING TURBINE FRAME (SETS) 8 856A2555G02 Beam 1 856A2567 Lifting Eye 4 856A2568 Lifting Eye( LPT AFT ) 2 856A2569G01 Support, Centering-LPT Shaft Forward 1 856A2573 Puller Adpt 1 856A2575G02 Stand, Storage - LPT 856A2576g01 Spacer Fixture 1 856A2577P01 Ring, Locating - No. 5 Bearing Rollers 1 856A2580 Puller Oil Nozzle 1 856A2581 Puller Oil Nozzle 1 856A2588 Pullers (TGB) 2 856A2590 Remove / Install Radial Drive Shaft 1 856A2591 Remov /Install Horizontal Drive Shaft 2 856A2593 Fixture Remove /Install 1 856A2593P03 Fixture Remove /Install 1 856A2593P11 Fixture Remove /Install 1 856A2600P09 LPT Shaft Guide And Stop Tool 856A2600P09 LPT Shaft Guide And Stop Tool 856A2600P09 LPT Shaft Guide And Stop Tool 856A2604G01 PULLER AIR/OIL SEPERATOR 1 856A2611 Pullers 1 856A2618 Fixture, Holding - Rotor/Stator, LPT 856A2618-4 Fixture, Holding - Rotor/Stator, LPT 856A2618G01 Fixture, Restraining (Part Of Tool) 1 856A2618G01 Fixture, Holding - Rotor/Stator, LPT 856A2618G02 Fixture, Restraining (Part Of Tool) 1 856A2618G02 Fixture, Holding - Rotor/Stator, LPT 2 856A2618G02 Fixture, Holding - Rotor/Stator, LPT 856A2618G03 FIXTURE ROTOR/STATOR 7 856A2618P02 Fixture, Holding - Rotor/Stator, LPT 1 856A2618P04 Fixture, Restraining (Part Of Tool) 1 856A2618P04 Fixture, Restraining (Part Of Tool) 1 856A2618P04 Fixture, Restraining (Part Of Tool) 1 856A2618P06 Fixture, Restraining (Part Of Tool) 1 856A2618P06 Fixture, Holding - Rotor/Stator, LPT 856A2625G01 Stand, Storage - Fan And Booster Module 1 5 856A2626G01 Stand, Storage - Module 2 2 856A2626G01 Stand, Storage - Module 2 2 856A2627g02 Lifters 3 856A2634 storage fixture lpt shaft module 1 O:\USERGRP\2014 Tasks\Tooling lists\cfm56-3 (FINAL_) 7 of 17 01/05/2014
856A2644 Fan Disc Holding Fixture 2 856A2645 Engine Lifters 2 856A2647 Horizontal Major Module Stand 8 856A2655 Radial Drive Shaft Fixture (Remove /Install) 1 856A2660 GAUGE AXIAL CLEARANCE LPT 1 O:\USERGRP\2014 Tasks\Tooling lists\cfm56-3 (FINAL_) 8 of 17 01/05/2014
856A2664 G01 VBV Gauge 3 856A2714G01 Fixture, Lift - LPT Module 3 856A2734G01 Baseplate, Support AGB Gearshafts 1 856A2753G01 SLIDING HAMMER 1 856A2784G01 Dolly - Booster And Balance Fixture Assy 1 856A2785G01 Beam, Lift - Balance And Booster 1 856A3012G01 Puller - No. 2 Bearing Inner Race 1 856A3012G02 Puller - No. 2 Bearing Inner Race 1 856A3012P02 Puller - No. 2 Bearing Inner Race 1 856A3012P04 Puller - No. 2 Bearing Inner Race 1 856A3013G01 Puller - N1 Speed Sensor Ring 1 856A3017G04 Fixture, Torque - No. 1 Bearing Housing 856A3017G04 Fixture, Torque - No. 1 Bearing Housing 856A3017G04 Fixture, Torque - No. 1 Bearing Housing 856A3018G01 Pusher - No. 1 Bearing Sleeve And No. 1 Bearing Inner Race 1 856A3020G01 Pusher - Sensor Ring And No. 2 Bearing Inner Race 1 856A3030G01 Ring, Lifting - Fan Stub Shaft, Rear 1 856A3033P01 Retaining Nut 1 856A3034G01 Puller - Forward Rotating Air/Oil Separator 1 856A3034G01 Puller - Forward Rotating Air/Oil Separator 1 856A3034G03P16 Puller - Forward Rotating Air/Oil Separator 856A3034G03P19 Puller - Forward Rotating Air/Oil Separator 856A3034G03P21 Puller - Forward Rotating Air/Oil Separator 856A3034G03P21 Puller - Forward Rotating Air/Oil Separator 856A3034G03P21 Puller - Forward Rotating Air/Oil Separator (P.O.T) 2 856A3034G03P21 Puller - Forward Rotating Air/Oil Separator 856A3049 Handling Fixture 2 856A3057 CVT Installation Tool + Spares 2 856A3057G05 Fixture, Torque - Center Vent Tube Spacer Sleeve Nut 7 856A3057G06 TORQUE FIXTURE 3 856A3058 No 5 Brg Pullers 1 856A3062 Puller, Hydraulic-rear Rotation Air/Oil Seal (Part of Tool) 1 856A3063G02 Puller - Rear Rotating Air Seal 2 856A3070 Wrench Radial D/Shaft 1 856A3072 Puller Tool Radial D/Shaft 1 856A3094G01 Baseplate, Assembly/Disassembly-LPT Cooling Manifolds 1 856A3097 LPT Stub Shaft Pullers 1 856A3100 Locating Tool 1 856A3101 Centre Vent Tube Plug 1 O:\USERGRP\2014 Tasks\Tooling lists\cfm56-3 (FINAL_) 9 of 17 01/05/2014
856A3108G01 KIT NO. 5 BNG. INSTALL 1 856A3114G01 Wrench - Captive Bolts Vbv Ballscrew Actuator 1 856A3115 Tool, Adjusting - Angular Setting, Vbv Linkage System 1 856A3160 Pusher Tool 1 856A3234P01 PROTECTOR LPT SHAFT 4 856A3242G01 Block, Support - Spool Booster 1 856A3242G01 Block, Support - Spool Booster 1 856A3242G01 Block, Support - Spool Booster 1 856A3242G01 Block, Support - Spool Booster 1 856A3242G01 Block, Support - Spool Booster 1 856A3242G01 Block, Support - Spool Booster 1 856A3242G01 Block, Support - Spool Booster 1 856A3242G01 Block, Support - Spool Booster 1 856A3242G01 Block, Support - Spool Booster 13 856A3244G01 Tool, Checking - Gap N1 Speed Sensor 1 856A3244G01 Tool, Checking - Gap N1 Speed Sensor 1 856A3244G02 Tool, Checking - Gap N1 Speed Sensor 1 856A3246G01 Guide, Alignment - LPT/LPT Shaft 1 856A3247 Guide, Alignment - LPT/LPT Shaft 1 856A3253 Hooks, Restraining Set - LPT Disk Air Seal 1 856A3253 Hooks, Restraining - LPT Disk Air Seal 2 856A3253 Hooks, Restraining - LPT Disk Air Seal 2 856A3253 Hooks, Restraining - LPT Disk Air Seal 3 856A3260 Plug Extractor LPT Shaft 1 856A3262G01 Puller - Fan Case Abradable Cartridge 4 856A3264G01 Positioner Mid Stream Fairing 1 856A3265 Machine Fixture 2 856A3268 Wrench(Centre Vent Tube Sleeve 2 856A3269 Wrench No5 Brg Inner Race 2 856A3272 PULLER NO.4 BNG ROTATING SEAL 1 856A3272 No 4 Brg Oil seal pullers 1 856A3276G01 STRENGTHENING RING LPT CASE 1 856A3278 Guide Pin 1 856A3279G02 Pusher, Puller - LPT Disk Bushings 2 856A3287 FIXTURE HOLDING FORWARD AIR SEAL 1 856A3308 Puller, Hydraulic - No. 4 Bearing Inner Race 1 856A3308G03 Puller, Hydraulic - No. 4 Bearing Inner Race (Part Of Tool) 1 856A3308G03 Puller, Hydraulic - No. 4 Bearing Inner Race (Part Of Tool) 1 856A3308G03 Puller, Hydraulic - No. 4 Bearing Inner Race (Part Of Tool) 1 856A3308P02 Puller, Hydraulic - No. 4 Bearing Inner Race (Part Of Tool) 1 856A3308P08 Puller, Hydraulic - No. 4 Bearing Inner Race (Part Of Tool) 1 856A3315 Centre Vent Tube Pullers 1 856A3320G03 Fixture, LPT Rotor/Stator 3 O:\USERGRP\2014 Tasks\Tooling lists\cfm56-3 (FINAL_) 10 of 17 01/05/2014
856A3322 Crimping Tool No 5 Nut 1 856A3323 FIXTURE INSTALLATION NO.1 BNG 1 856A3328G01 Tool Set, Adapters - No. 1 And No. 2 Bearing Oil Nozzles Air Impingement Checks 1 856A3329G02P03 Tool Set, Targets - No. 1 And No. 2 Bearing Air Impingement Checks 856A3329G02P12 Tool Set, Targets - No. 1 And No. 2 Bearing Air Impingement Checks 856A3343G02 Pins 16 856A3344G04 Puller, - No. 1 Bearing Housing 1 856A3345G01 Tool Locking - No. 1 Bearing Retainer Nut 1 856A3345G01 Tool Locking - No. 1 Bearing Retainer Nut 1 856A3358G02 Fixture, Holding - No. 4 Bearing Inner Race Bolts (Part of Tool) 1 856A3358G03 Fixture, Holding - No. 4 Bearing Inner Race Bolts 1 856A3358G03 Fixture, Holding - No. 4 Bearing Inner Race Bolts 1 856A3358G03P3 Fixture, Holding - No. 4 Bearing Inner Race Bolts 1 856A3373 FIXTURE HOIST LPT BLADED DISKS 2 856A3383 Fixture, Alignment - Turbine Frame/LPT Rotor 1 856A3383P03 Fixture, Alignment - Turbine Frame/LPT Rotor 1 856A3383P04 Fixture, Alignment - Turbine Frame/LPT Rotor 1 856A3386 Heat diffuser HPT Shaft 1 856A3387G02 Fixture, Handling/Turn - LPT Case And LPT Shroud Support 1 856A3387G02 Fixture, Handling/Turn - LPT Case And LPT Shroud Support 1 856A3387G03 Fixture, Handling/Turn - LPT Case And LPT Shroud Support 1 856A3387G03 Fixture, Handling/Turn - LPT Case And LPT Shroud Support 1 856A3389 Puller Tool Radial D/Shaft 1 856A3392 Torque Wrench 1 856A3408G02 VBV Rig Setting Plate 2 856A3409P03 Guide Pins 2 856A3416 Puller, Rotating Air Seal-stage 3 1 856A3419G02 Adapter, Puller - Oil Inlet Cover 4 856A3425G01 Puller, Rotating Air/Oil Seal 2 856A3431 Heat diffuser LPT Shaft 1 856A3432 FEELER GAUGE TOOL 1 856A3433G02 Tool Set, Trunnions (Tool Set) 1 856A3433G02 Tool Set, Trunnions (Tool Set) 1 856A3433G02 Tool Set - Trunnions(Tool Set) 1 856A3433G02 Tool Set - Trunnions(Tool Set) 1 856A3433G02 Tool Set - Trunnions(Tool Set) 1 856A3433G02 Tool Set - Trunnions(Tool Set) 1 856A3433G02 Tool Set - Trunnions(Tool Set) 1 856A3433G02 Tool Set - Trunnions(Tool Set) 1 856A3439 Brg Protector 1 856A3440G02 Puller, Ring, Bearing (Part Of Tool) 2 O:\USERGRP\2014 Tasks\Tooling lists\cfm56-3 (FINAL_) 11 of 17 01/05/2014
856A3443G03 Puller, No. 5 Bearing - Outer Race And Sleeve (Part of Tool) 2 Puller, Outer Race And Sleeve - Bearing No. 5 (hydraulic 856A3443G03 (Local Manupuller) Locally Sourced 1 856A3443P17 Puller, Outer Race And Sleeve - Bearing No. 5 1 856A3443P17 Puller, Outer Race And Sleeve - Bearing No. 5 1 856A3445G02 Tool Set, Trunnions, Lift And Turn - LPT Module 1 856A3445G02 Tool Set, Trunnions, Lift And Turn - LPT Module 1 856A3460 Checking tools for centre vent Tube(Set) 1 856A3472 Checking Tool (CVT) 2 856A3473 CVT Master 1 856A3485 Protector 2 856A3500G01 Fan blade Spacer Puller 1 856A3501G03 Fixture, Alignment/Guide Booster/LPT Shaft 4 856A3501G03 Fixture, Alignment/Guide Booster/LPT Shaft 3 856A3502G05 FIXTURE COUNTER TORQUE 8 856A3502G06 FIXTURE COUNTER TORQUE 1 856A3503G01 Fixture, Removal/Installation And Handling - Booster Rotor/Stator Assembly 1 856A3503G01 Fixture, Removal/Installation And Handling - Booster Rotor/Stator Assembly 1 856A3504G01 PUSHER/PULLER FIXTURE 1 856A3504G02 PUSHER/PULLER FIXTURE 1 856A3504G03 PUSHER/PULLER FIXTURE 4 856A3505 Tool Set Leak Test 1 856A3506-8 Wrench, Torque/Loosen - LPT Coupling Nut 1 856A3506G03 TORQUE WRENCH LPT 1 856A3507G01 Guide, Fwt Support 1 856A3507G01 Guide, Fwd Support 1 856A3507P02 Guide, Fwd Support 1 856A3507P03 Guide, Fwd Support 1 856A3508G01 Sleeve, Centering And Removal/Installation Module 1/LPT Major Module 6 856A3508G01P02 Sleeve, Centering and Removal/Installation 1 856A3508P08 Guide Pins 5 856A3509 G / Box Locking tool 6 856A3509 AGB Engine Locking Tool 2 856A3510 Adapter, Lift And Turn - 1 And 2 Brg Support 1 856A3510 Adapter, Lift And Turn - 1 And 2 Brg Support 3 856A3510 Lifting Fixture 1 856A3510G01 Adapter, Lift And Turn - 1 And 2 Brg Support 3 856A3512G02 FAN DISK DUMMY 3 856A3513G04 RESIDUAL TORQUE BEAM 4 856A3514P02 RESIDUAL TORQUE ADAPTER 2 856A3515 Lifting Beam 2 856A3515 Extension Beam Lifter 1 856A3516G01 SLEEVE PROTECTIVE FAN DISK 1 856A3517G01 Adapter, Counter Torque 3 856A3517G01P03 Adapter, Counter Torque (Part of Tool) 1 O:\USERGRP\2014 Tasks\Tooling lists\cfm56-3 (FINAL_) 12 of 17 01/05/2014
856A3518 Fan Blade Storage Stand 7 856A3519G01 Sling, 3 - Leg - Agb Handling 1 856A3519G01 Sling, 3 - Leg - Agb Handling 1 856A3520G01 Cover, Protective - Fan Disk/Booster Balancing 1 856A3524P02 Tool Set, Drive Adapter - Booster And LPT 2 856A3525G04 Cradle, Removal/Installation - Agb 1 856A3526G03 Baseplate, Mobile - Booster 2 856A3526G03 Baseplate, Mobile - Booster 1 856A3526G03 Baseplate, Mobile - Booster 3 856A3526G03 Baseplate, Mobile - Booster 2 856A3528G01 Block Support - Booster Spool 3 856A3528G01 Block Support - Booster Spool 1 856A3531G02 Gearbox, Accessory, Dummy 1 856A3531P01713 Gearbox, Accessory, Dummy (Part Of Tool) 1 856A3532 Fixture, Lift And Turn - Fan Frame Assembly 856A3534 Fan Inlet Sling 3 856A3535 Fixture, Lift - Booster Rotor/Stator Assembly 3 856A3536 Support, Locator - Booster Rotor 1 856A3537G01 Tool, Checking, Position - Agb 1 856A3539P09 Pins 2 856A3540 Handling Fixture 2 856A3542G01 Weight, Axial Loading - No. 1 Bearing 1 856A3543G01 FIXTURE HANDLING / TURN 2 856A3544 ADPT Flange 1 856A3545 AGB Stand 1 856A3546 Backlash tooling 1 856A3547 Tool Set (TGB Oil Nozzle ) 1 856A3548G03 Tool Set, Target - Agb Oil Nozzle Impingement Test 1 856A3549 Tool Set, Leak Test - Agb 1 856A3549 Tool Set, Leak Test - Accessory Gearbox 1 856A3549P03 Tool Set, Leak Test - Accessory Gearbox 1 856A3549P04 Tool Set, Leak Test - Accessory Gearbox 1 856A3549P04 Tool Set, Leak Test - Accessory Gearbox 1 856A3549P05 Tool Set, Leak Test - Accessory Gearbox 1 856A3549P08 Tool Set, Leak Test - Accessory Gearbox 1 856A3549P09 Tool Set, Leak Test - Accessory Gearbox 1 856A3549P11 Tool Set, Leak Test - Accessory Gearbox 1 856A3549P12 Tool Set, Leak Test - Accessory Gearbox 1 856A3549P12 Tool Set, Leak Test - Accessory Gearbox 1 856A3549P13 Tool Set, Leak Test - Accessory Gearbox 1 856A3549P14 Tool Set, Leak Test - Accessory Gearbox 1 856A3549P15 Tool Set, Leak Test - Accessory Gearbox 1 856A3549P15 Tool Set, Leak Test - Accessory Gearbox 1 856A3549P35 Tool Set, Leak Test - Accessory Gearbox 1 856A3549P36 Tool Set, Leak Test - Accessory Gearbox 1 856A3549P38 Tool Set, Leak Test - Accessory Gearbox 1 O:\USERGRP\2014 Tasks\Tooling lists\cfm56-3 (FINAL_) 13 of 17 01/05/2014
856A3550 Tool Puller set 1 856A3552 Holding Fixture 1 856A3553 Locking fixtue Set 1 856A3554 Tool Set Remove/Install 1 856A3555 Wrench 1 856A35562 Tool Set Remove/Install 1 856A3561 Wrench 1 856A3565 Base Plate Support (AGB) 1 856A3566 Tool pusher Set 1 856A3567 pullers (AGB) 1 856A3570G01 WRENCH NO. 2 BNG 1 856A3571G02 Wrench - Forward Rotating Air/Oil Separator Nut 1 856A3572G01 Wrench, No. 1 Bearing Inner Race Nut 1 856A3573 Tool, Assy/Disassy - No. 1 And No. 2 Bearing Support 856A3573 Tool, Assy/Disassy - No. 1 And No. 2 Bearing Support 2 856A3573G03 Tool, Assy/Disassy - No. 1 And No. 2 Bearing Support 856A3573G03 Tool, Assy/Disassy - No. 1 And No. 2 Bearing Support 856A3573G03 Tool, Assy/Disassy - No. 1 And No. 2 Bearing Support 1 856A3574-4 PULLER NO.1 BNG SLEEVE 1 856A3574P02 Puller - No. 1 Bearing Sleeve 1 856A3575G01 Puller - No. 1 Bearing Inner Race 1 856A3575P02 Puller - No. 1 Bearing Inner Race 1 856A3576 Tool Set Install /Remove 1 856A3580 Fan Case Abradable Strip Machine 1 856A3582 Wrench LPC 1 856A3596G02 Beam, Lifting - Fan Frame 1 856A3598G01 Cradle, Rem/Install - Fuel Pump And Mec Package 1 856A3600 Pullers(Radial Drive Shaft) 1 856A3604P01 WRENCH D/SHAFT NUT 1 856A3604P01 Horizontal Drive Shaft Nut Spanner 1 856A3606 Pullers 1 856A3607 TGB Bearin Pusher 1 856A3610G01 Fixture, Checking, Dim V - No. 1 And 2 Brg Support 856A3610G01 Fixture, Checking, Dim V - No. 1 And 2 Brg Support 856A3617G01 Lube Unit magnetic Plug( Remove/Install Tool) 2 856A3618G01 Tool Set, Pushers 1 856A3618G01 Tool Set, Pushers 1 856A3618G01 Tool Set, Pushers 1 856A3618G01 Tool Set, Pushers 1 856A3628G01 No 1 Installation Tool 1 856A3710G01 Lifting Beam 2 O:\USERGRP\2014 Tasks\Tooling lists\cfm56-3 (FINAL_) 14 of 17 01/05/2014
856A4005G02 HPT Blade Cleaner 1 856A4050G01 Vane Sector Set 1 856A4055 HPC Blade tip Grinder Machine 1 856A4116G01 Fixture, Grind - Stationary Air/Oil Seal, No. 3 Bearing Aft 1 856A4133 Refacing Kit Internal 1 856A4134 Refacing Kit Exnternal 1 856A6629G03 Slot Wear gauge 1 9970-957-509 Guide Fixture 2 A10072.02 Schenk 1-2 Balance Arbor 1 A101772 Schenk Balance Fixture 1 A104266 Schenk Balance Fixture 856A3450G01 1 A104266.01 LPT Dynamic Fixture 1 A10562501 Balance fixture (21X Booster) 856A2783G01, 856A3829G01 1 A11040102 Schenk (Hydraulic Chuck) 1 A112257 Schenk Balanc Kit 1 A121455.01 CFM TOOL 1 ALF-60 Acustic Panel Screw Tool 1 CRS110 Engine Lifters 1 Eagle Pro Hydraulic Ram S/N 09080809-002 1 ENEPAC Hydraulic Ram 1 Jt-5176-17609-01-B Turn Table 1 LC0032 Flexi Brace 1 LC0058 HYDRAULIC VALVE CFM 1 LC0072 Tooling Fixture 1 LC0090 Wrench 1 LC0192 Lifting ARM 1 LC0200 Fixture 1 LCO061 Hydraulic Ram 1 LCO222 Wheel 1 LCO231 Lifting EYE 1 LCO234 Lifting EYE 1 LCO316 Hydraulic Ram 1 LCO381 Transport Stand 1 LCO520 Hydraulic Ram 1 LCO521 Hydraulic Ram 1 LCO522 Hydraulic Ram 1 LCO630 Sling 1 LTAI326 Magnetic Field Gauge 1 Model 8111 Sweeney S/N TT0039 1 Model 8111 Sweeney S/N STM014 1 Model 8RSP53/VDS/374 Sweeney Drive S/NA99A21155 1 N/A Core CDP Runout Kit 1 N/V ARBOUR HPC STG 4-9 S/N CRSHT409E 1 R001891.101 Schenk HPC Dummy Arbor 856A1160G01 2 R001896.101 Schenk HPT Dummy Arbor 2 R070206.101 SCHENCK LIFTING TOOL 1 O:\USERGRP\2014 Tasks\Tooling lists\cfm56-3 (FINAL_) 15 of 17 01/05/2014
SCHENCK LPTbalance fixture & stand 1 TT110-10 True Temp Indicators 2 NV Pull Gauge 0--30 LB S/N LAI854 1 856A3394G01 Fixture (LPC Build Fixture) 1 856A3580G03 Fan Case Machining Fixture(Abradable Strip) 1 278017 Fuel Pump Clamp 1 216565 Spline Socket Fuel Pump 1 Goliath Taps Fuel Pump 3 Scott Taps Fuel Pump 4 216562/9 Splined Drive Fuel Pump 1 217051 Fuel Pump Tool 1 216560 Fuel Pump Tool 1 216692 Fuel Pump Tool 5 1754M36P01 Feuel Pump Gasket 1 Un3A Dyes Fuel Pump 2 216562 Fuel Pump Tool 1 216676 Fuel Pump Tool 1 N/V Fuel Pump Pin 1 N/V Fuel Pump Cylendrical Tool 1 216561 Fuel Pump Tool 2 100-47856-1 Fuel Pump Tool 1 N/V Go/No GO Gauge 1 N/V Fuel Pump Tool 1 Facom Socket 1 7/16" 1 216746 Fuel Pump Tool 1 N/V Fuel Pump Splined ADPT 1 Goliath 9/16 " Tap Set 1 207968 Fuel Pump Tool 1 216718 Fuel Pump Tool 1 N/V Fuel Pump Blank 6 N/V Fuel Pump Blanks 2 1754M36P01 Fuel Pump Gasket 2 34724 Adpts Heat Exchanger 8 68600-228-1 Adpt Oil Fuel Heater 1 N/V Clamping Ring CFM 1 506T725-01 Tool Set Fuel Nozzle 2 N/V Support Fixture Fuel Nozzle 1 N/V Pusher/Puller Fuel Nozzle 1 6877020M2 Tool Set CFM nozzle 3 DPS-20R EVC Digital Force Gauge 1 GS-13655-1 EVC Fixture 2 GS22209-1 EVC Fixture 1 GS13656 EVC Fixture 2 N/V Adjustable Clamp 1 T2757-2 Tool VSV Actuator 2 T257-1 VSV Piston Guide 1 N/V Aluminium 1 T1334-5 Tool VSV 1 O:\USERGRP\2014 Tasks\Tooling lists\cfm56-3 (FINAL_) 16 of 17 01/05/2014
T3159-12 Tool VSV Wrench 1 T2231-1 Extractor Tool 1 T1334-7 Tool VSV 1 N/V Tool Heat Exchanger 4 N/V O Ring Guides 2 N/V Socket Fuel /Oil Cooler 2 68600-267-1 Wrench Fuel/Oil Cooler 1 68600-253-1 Fixture Heat Exchanger 1 BA8303-1 Gasket Heat Exchanger 1 856A1178G01 Pliers 1 68600-209-1 3 LeggedPullers 1 68600-255-1 3 LeggedPullers 1 N/V 3 LeggedPullers 1 AT1581 Fixture Servo heater 2 68600-234-1 Fixture Servo heater 1 AT1489 Test fixture 1 68600-266-1 Blanking Cover 1 68600-225-1 Fixture oil/ Fuel Heatexchanger 1 68600-266-1 Blanking Cover 1 N/V Fixture Circular Threaded 1 P20405 Test Pot Fuel Heater matrix 1 19179 Extractor Matrix 1 68600-251-1 Servoheater Tool 1 68600-227-1 Heatexchanger ADPT 1 F19178-4-5 Heatexchanger ADPT 1 68600-251-1 Blanking Plate 2 68600-252-1 Blanking Plate 1 68600-230-1 ADPT Plate Heatexchanger 1 F19441 Tube ADPT Servoheater 2 F19178 ADAPT Heatexchanger / Servo heater 1 O:\USERGRP\2014 Tasks\Tooling lists\cfm56-3 (FINAL_) 17 of 17 01/05/2014