COMMERCIAL FILTER SYSTEMS

COMMERCIAL FILTER SYSTEMS Commercial Aquatic Supplies is able to supply filter systems to meet the needs of all public pools. When considering new or replacement filters for your pool it is important to understand the different types of filter systems. DE Filters - The Media Diatomaceous earth, (DE) provides high quality filtration removing particles which can be as small as three to five microns in size. It is cheap and because it has many uses is readily available. It is heavy enough that it is not flushable and can block drains. It is classed as a hazardous material so must be disposed of properly. Perlite is an alternative media which can be used in DE filters to achieve almost the same filtration. It is lighter than DE making it easier to handle, specifically to get it in and out of filters. It is not classed as a hazardous so disposal can be as simple as flushing it down the drain. Vacuum or Open Pit DE Filters These are the most common types of DE Filters. They are open tanks, typically below pool water level and filled by gravity. The pool pump sucks water through the filter and pushes it back to the pool. These types of filters are economical to build and offer better quality filtration in a smaller space than similar capacity sand filters. Maintenance is also easy, and there is very little water loss during use and maintenance. VACUUM DE FILTER Pressure DE Filters In these systems the DE filter elements are mounted in a pressure vessel, just like a sand filter, filling the need for a closed system which some pools require, while maintaining the DE advantages, but at a higher price. Sand Filter Systems Sand Filters are the most common filter systems. They are economical to purchase, install and maintain. The filtration is not as fine as DE, typically in the 5-20 micron range. The media is semi-permanent, back washing is easy, and they are available in all shapes and sizes, and can even be installed outdoors. Water consumption, primarily for backwashing is much higher than for DE filters. The advantages outweigh the disadvantages, making these the most popular filter systems in the marketplace currently. NEPTUNE BENSON PRESSURE DE FILTER Pricing Commercial Aquatic Supplies will provide specifications and quotations on filter types including pricing, installation, and delivery quotations. Large filter systems are not a stocked item. Astral Eureka Mer-made Waterco Neptune Benson Stark WATERCO VERTICAL SAND FILTER WATERCO HORIZONTAL SAND FILTER NEPTUNE BENSON STACKED HORIZONTAL SAND FILTERS Toll Free Line:.800.663.5905 Fax: 604.980.096 Phone: 604.980.282 www.commercialaquaticsupplies.com 3

VERTICAL AND HORIZONTAL SAND FILTERS by Waterco VERTICAL SIDE MOUNT SAND FILTER Waterco makes a wide range of vertical and horizontal fiberglass sand filters, some of the most common are listed below. For Deep Sand Bed or Larger Diameter or Capacity Vertical or Horizontal Filters please enquire for a quotation and spec sheet. Waterco specializes in filament wound seamless one-piece fiberglass filters rated at 50psi, NSF 50 approved, and with Waterco s 0 year warranty, (5 + 5 pro rate). Vertical Side Mount Sand Filters Model# dia bed area flow sand pipe size Price SM 050 42 8.5 9.3 40 2270 3 MPV $POR SM200 48 22.8 2.8 83 2270 3 MPV $POR SM400 56 26.4 6.58 249 3640 3 MPV $POR SM600 64 26.4 2.66 325 4770 4 MPV $POR Above include Multiport Valves with a single pressure gauge on the tank (no guage panel). Micron Horizontal Sand Filters Model # dia x L area flow sand Pipe size Price 2228075 42 x 75 9.6 294 550/2000 4 $POR 222809 42 x 9 24 360 900/800 6 $POR 2228006 42 x 06 28.2 423 050/200 6 $POR 2228020 42 x 20 32.2 483 250/2750 6 $POR W22345 Gauge Panel 2 X 0-60 PSI $POR Above does not include face piping or gauge panels. Sand bed depth on 42 diameter filters is 6 Sand = gravel / sand in pounds WATERCO HORIZONTAL SAND FILTER MICRON HORIZONTAL SAND FILTER 4 www.commercialaquaticsupplies.com Phone: 604.980.282 Fax: 604.980.096 Toll Free Line:.800.663.5905

Defender Regenerative Media Filters by Neptune Benson This is a pressure DE filter, which has the following features. The filter footprint is very small given the flow, compared to Vacuum DE or Sand Filters. These filters are designed to use Perlite, a filter media similar to DE but which does not contain crystalline silicate, the Hazardous Component of DE, making Perlite a nuisance dust only, and Perlite is lighter than DE which means it is flushable, without clogging drains. When the pressures in a Defender filter rises, instead of backwashing the filter it can be Bumped, the media shaken up, redistributed, and reused several times before being replaced. The water usage to maintain/backwash this style of filter is very low. The Lever Bump models are very simple and reliable to use, and custom larger models typically have these features power assisted/automated to simplify maintenance. The recommended/ideal flow rate for these filters is.2 usgpm/ft2, the maximum flow rate is 2.0 usgpm/ft2. These products carry NSF, UL, and CE certifications. The larger models are priced as requested. As a replacement filter the Neptune Benson Defender Regenerative Filter requires a small footprint and can be modified to fit thru doorways. This plus the additional benefits described on this page make this the ideal filter to consider when replacing or upgrading older filters. Also ask for a cost benefit information package for your pool. These filters are priced on request. Features: ) Steel tank with Flexsol 3000 interior lining and 0 year fully rated warranty. 2) Automation can be upgraded with a Filter Controller to Automate and monitor all of the filter operations, and provide connectivity to VFD and UV systems. 3) Vacuum transfer of media, for ease of operation and no dust. 4) Integral filter mounted lifting davit for ease of access when needed. 5) The Bump feature lengthens filter run times. Benefits: ) Low filter pressures allow more water flow at less head pressure resulting in electrical energy savings. 2) Reduction of backwash waste results in corresponding savings in water and water treatment costs. Toll Free Line:.800.663.5905 Fax: 604.980.096 Phone: 604.980.282 www.commercialaquaticsupplies.com 5

Defender Regenerative Media Filter Specifications by Neptune Benson Parts Quoted on Request 6 www.commercialaquaticsupplies.com Phone: 604.980.282 Fax: 604.980.096 Toll Free Line:.800.663.5905

PAC FAB Triton ll Sand Filters Pac Fab s Triton fibreglass filters are rated for public pool use and are easily adaptable to multi unit installations. Tritons are commonly used on Whirlpools, Tot Pools, and smaller Institutional Pools. This filter offers the best price point for a fibreglass commercial filter. Key advantages of Triton Filters include it is a proven filter (with thousands of installations in place), parts are readily available (and reasonably priced), and Tritons are straight forward to work on. Filters are supplied complete, only the filter media needs to be ordered separately. Specification sheets are available. Pac Fab also makes commercial and heavy-duty" (C) versions of the Triton. Capacity and Ordering Information 5GPM Gallons LBS Pump Sq.Ft. of Pipe per Sq.Ft. per #20 Filter Model Size Filter Area Size Ft. Rate 6 Hours Sand *Price TR-40 8"D ½ or ¾hp.92 /2" 29 0440 75lbs $85.00 TR-50 2"D ¾ or hp 2.46 /2" 37 3320 225lbs $884.00 TR-60 24"D or ½hp 3.4 /2" 47 6920 325lbs $075.25 TR-00 30"D ½ or 2hp 4.9 2" 74 26640 600lbs $289.25 TR-00C ½ or 2hp 4.9 2" 74 26640 600lbs $354.50 TR-40 36"D 2 to 3hp 7.06 2" 06 3860 925lbs $636.75 TR-40C 2 to 3hp 7.06 2" 06 3860 925lbs $743.00 *Pricing includes filter and matching pre-plumbed dial valve. Triton Filter Replacement Parts Dia # Part # Description Price 54689 Air Bleeder Tee Assembly $38.00 2 54700 Adapter $5.45 3 00-60 Gauge, back mount $8.50 4 5466 Adapter o-ring $2.30 5 54664 Adapter nut $2.25 6 54570 Closure Dome, buttress thread $08.00 6 54559 Closure Dome, V thread, $72.00 7 54493 Closure Dome o-ring $6.90 8 50035 Strainer for air relief tube - 99 on 3/8" OD $8.5 9 54438 Air Relief Tube TR 40 $3.00 0 54906 Diffuser, TR 40 $69.00 54500 Upper piping Assembly, TR 40 $64.00 2 50036 Air Relief Tube Connector - 99 on 3/8" OD $2.00 3 54489 Lower Piping Assembly TR 40 $75.00 4 000000 Replacement tanks POR 5 52290 Lateral TR 40-60 to 7 July 07 $9.80 50085 Lateral TR 60, after 7 Jul7 07 $.5 52202 Lateral TR 00 $3.40 54540 Lateral TR 40 $28.00 6 54763 Hub TR 40-60 to 7 July 07 $4.00 55753 Hub TR 60 after 7 July 07 $57.00 54453 Hub Tr 00-40 $38.00 7 52220 Sand Drain 2 $58.00 7 54698 3/4 Sand Drain $34.00 8 3576 ¼ Drain Plug $5.25 9 5452 Wrench $34.00 20 5442 2 Internal Locknut $2.80 2 5446 2 Internal Spacer $8.65 22 54492 Bulkhead o-ring 3.40 23 54408 2 External Spacer $8.65 24 54538 Bulkhead gasket $2.80 25 54405 2 Bulkhead Fitting $96.00 26 925 Drain Plug o-ring $.65 27 5448 Washer, 3/8 SS $.55 28 54596 Foot TR 40 $94.00 29 274494 O-ring, valve adapter $6.30 33 5464 Closure Kit, 6 Buttress thread $255.00 34 54687 Fitting Package, w/o gauge $63.00 BLACK TANK Toll Free Line:.800.663.5905 Fax: 604.980.096 Phone: 604.980.282 www.commercialaquaticsupplies.com 7

Triton Filter Replacement Parts Replacement Dial Valves Pre-plumbed For Triton Filters 2673 SM-PP3 Pre-plumbed ½ Dial Valve $3.60 26055 SM2-PP3 Pre-plumbed 2 Dial Valve $68.75 Praher Dial Valves (complete but not preplumbed) Item No Item Description Price 0 0 SM-0-AO ½ Dial Valve, side mount, all ports open POR (½ FIPT) 0 02 SM-20-AO 2 Dial Valve, side mount, all ports open $POR (2 FIPT) 0 03 SM-30-AO 3 Dial Valve, side mount, all ports open $784.00 (3 SLIP) Praher Dial Valve Replacement Parts Part Numbers ending in are for ½ pipe size dial Valves Part # Description Price E--S- Handle-ABS $ 7.35 E-2-S- Pin $ 3.5 E-3-S- Washer $ 2.0 E-4-S- Screw M6 X 30MM Philips Pan Head $.05 E-6-S- Cover $2.55 E-7-S- Cover O-ring $ 4.20 E-8-S- Washer $ 2.0 E-9-S- Spring $ 9.40 E-0-S- O-rings $ 2.0 E--S- Diverter $6.70 E-2-S- Diverter gasket $ 7.35 E-4-S- Nut M6 - Hex $ 0.55 E-5-S- ¼ Plug $.05 E-6-S- Site Glass gasket $.5 E-7-S- Site Glass $ 3.5 E-50-S- Top Assembly (#-) White $65.00 Part # ending in 2 are for 2 dial valves. Parts not listed are in common with S- valves E-7-S-2 Cover O-ring-2 $ 4.20 E--S-2 Diverter 2 $8.80 E-2- S-2 Diverter Gasket 2 $ 9.40 E-50- S-2 Top Assembly 2 (#-) White $74.00 Part # ending in 3 are for 3 pipe size dial valves. E-6-S-3 Cover 3 $24.95 40.56 Cover, new, after Jan 2002 $24.95 E-7-S-3 Cover O-ring $33.85 E--S-3 Diverter $254.97 4.34 Diverter c/w integral gskt, after Jan 2002 $309.80 E-2 S-3 Diverter gasket $83.65 E-50-S-3 Top Assembly (3 - ) White $774.5 Prism 2 oz Spider Gasket Glue $60.65 Other 3 dial valve parts on request 8 www.commercialaquaticsupplies.com Phone: 604.980.282 Fax: 604.980.096 Toll Free Line:.800.663.5905

TR 00C & TR 40C Replacement Parts Dia # Part # Description Price 3 273564 Manual Air Relief Assembly $40.00 4 00-60 Back Mount Gauge $8.50 5 27353 O-ring for Air Bleed $.20 7 54575 Closure Dome, 8 ½ $87.00 27 54527 Wrench for 8 ½ closure $39.00 8 52509 Dome Square O-ring $9.60 3 5442 2 Nut for Air Relief $2.80 9 274494 Drain O-ring $6.30 20 52220Z Drain Assembly $58.00 All parts not listed are in common with the regular filters, see previous page. Astral Laterals - Old Style Part No Description Price 00629 00mm long-threaded both ends $8.85 00628 0mm long-closed one end $8.85 00627 60 mm long-closed one end $8.85 00626 225mm long-closed one end $8.85 00630 Coupling ¾" female/female $8.85 723R44020 Lid Gasket $33.75 Astral Laterals- New Style Part No Description Price 30775 Lateral, ½ X 3-9/6 $9.00 30776 Lateral, ½ X 6-5/6 $0.50 30777 Lateral, ½ X 8-7/8 $2.00 30778 Lateral, ½ X 0-¼ $2.75 30779 Lateral, ½ X 2-3/6 $3.50 30780 Lateral, ½ X 4-3/6 $4.25 3078 Lateral, ½ X 7 $5.00 30782 Lateral, ½ X 8-¾ $5.75 30783 Lateral, ½ X 2 $6.50 Swimquip Laterals Part No Diameter Length Price 24300-7 ½" 8 3/ 8" $8.05 24300-8 ½" 9 ¾" $8.05 24300-9 ½" 5" $87.0 24300-2 ½" 7" $93.95 24300-3 2" 3" $47.0 24300-32 2" 5" $5.05 24300-33 2" 7" $5.05 24300-34 2" 2" $54.45 24300-35 2" 23" $56.25 24300-36 2" 25" $73.25 24300-37 2" 30" $77.25 Longer laterals priced on request Toll Free Line:.800.663.5905 Fax: 604.980.096 Phone: 604.980.282 www.commercialaquaticsupplies.com 9

D.E. FILTER PARTS D.E. Filter System Tips Good precoats are essential to getting clarity and to keeping septa clean. Normal dosage is 2 ounces per sq.ft. of filter area. Object is to deposit at least /6" over all parts of all element. Precoat filter at U.S. GPM per sq. ft. of filter area. Maximum flow rate for filtration is 2 U.S. GPM per sq. ft. however -.5 GPM is better. Check for grease, metal staining, body oils, and other discolourations on filter elements. Buildup of dirt will shorten filter cycles. Check for warped or broken elements on a regular basis. SwimQuip D.E. Filter Discs Complete FOB Factory Item No Description Size Price 20+ FD-50-00 *Filter Disc 4.5"D $46.40 $4.67 FD-620-00 *Filter Disc 6"D $53.32 $47.75 FD-2600-33 Centre Disc 26"D $3.95 $28.0 29330-0033 Spacer Please inquire *When ordering please specify hub style or type. D.E. Filter Covers Item No Description Size - 2+ 07 0 Generic 30" x 60" $28.67 $5.58 07 05 Gasket for 30" x 60" $8.75 $7.00 VFC-3660- Generic BIF 36" x 60" $275.00 $247.75 07 2 Generic 30" x 36" $.40 $00.05 Custom D.E. filter Covers. Available on request. Sample cover or element required for accurate sizing and pricing. GENERIC 30 X 60 ELEMENT D.E. Filter Element Cores FOB Factory Item No Description Size -6 7+ 07 03 Generic 30" x 60" $369.0 $33.50 Item No Description Size -7 8+ PS3660 Generic BIF 36" x 60" $079.5 $992.50 side outlet Item No Description Size -4 5+ 07 09 Generic 30" x 36" $302.27 $27.50 0 www.commercialaquaticsupplies.com Phone: 604.980.282 Fax: 604.980.096 Toll Free Line:.800.663.5905

Premium Filter Media - FOB North Vancouver Item No Description - 2-29 30+ 06 0 #20 Filter Sand (50 Lbs) $7.67 $5.87 $4.8 06 02 #2 Coarse Aquarium Sand $34.40 $30.33 $28.84 (50 Lbs) FOB Factory Pallets $25.00 NOTE: If you are unsure of the amount of media for your filter, call with the model number and diameter and we will check the specs for you. DE, Diatomaceous Earth Filter Media Item No Size Per Unit 0+ Pallet Lot of 39 3 07 55 50 LB $60.79 $54.60 @ $,407.93 Perlite Filter Media Item No Size Per Unit 0+ Pallet Lot of 39 3 07 50 25 LB $67.75 $60.85 @ $2,25.60 DE Filter Tips Good precoats are essential to getting flow, clarity and keeping elements clean. Normal doseage is 2 ounces of DE per square foot of filter area, or follow manufacturers precoat dosage instruction. Object is to deposit at least /6 over all parts of filter elements. Precoat flow rate should be no more than US gallon per square foot of filter area. Maximum filter flow rate should be no more than 2 USGPM per square foot, and preferably in the range of to.5 USPGM per square foot. Check filter elements for spots not covered by precoat. This normally indicates body oils of grease or mineral staining on the elements which should be cleaned off or it will affect flow and length of filter cycles. Check regularly for warped or broken filter elements and repair as required to maintain filter performance and prevent filter media from leaking into pool. Dryden Aqua Activated Filter Media This is made of crushed green and amber glass, sized and activated, and used to replace sand as a permanent media. Multiply the current sand or gravel weight by 0.85 to determine amount needed, no filter modifications required, and note the backwash rate required is 8usgpm/square foot. Item No Description Size Per Unit 5+ Pallet lots of 45 AFM Grade 2 KG $60.5 $54.35 $2,289.60/pallet AFM 3 Grade 3 2 KG $60.5 $54.35 $2,2289.60/pallet Toll Free Line:.800.663.5905 Fax: 604.980.096 Phone: 604.980.282 www.commercialaquaticsupplies.com

Whisperflo Pumps by Pac Fab These pumps are very quiet and efficient. Flows are high for the HP. They work well with fiberglass filters because the shut off head is low at 45 psi. Model # HP Volts PH Price 05 ½ 5/208/230 $674.3 052 ¾ 5/208/230 $822.5 053 5/208/230 $888.58 054 ½ 208/230 $976.27 055 2 208/230 $47.93 056 3 208/230 $479.68 *3 Phase Motors and other Voltages available on request *For 575 Volt, 3 phase pumps please purchase as follows. Pumps will be shipped unassembled, so motor rotation can be checked before assembly. Model # HP Description Price Varies 3/4-3 Wet end - Custom Order $645.65 Varies 3/4-3 Motor only - Custom Order POR Whisperflo Pump Parts Dia # Part # Description Price 35750 Clamp Ring-plastic $55.05 2 3575 Lid $4.0 3 35003 Lid O-ring $3.55 4 070387 Basket $22.75 5 070430 Bolt, 3/8-6 X.25 $2.89 6 07284 Washer 3/8 $.75 7 07043 Bolt, 3/8 X.75 $3.5 8 07400 Nut, 3/8 $.75 9 35700 Gasket-seal plate $8.5 0 35757 Volute-black $260.45 355227 O-ring $3.69 2 07660 Set Screw $3.69 3 072927 Diffuser, /2 to 2 ½ hp $87.40 3 072928 Diffuser, 3 hp $04.05 4 07652 Set Screw $3.02 5 07573 Rubber Washer $.76 6 PS 000 Mechanical Seal $9.70 7 070429 Bolt, 3/6-6 X 7/8 $3.25 8 350202 Seal plate Kit, #6 & #8 $229.85 9 070336 Foot $43.70 20 35760 Foot Insert $22.76 2 07657 Screw, ¼-20 X $.76 22 07406 Nut, ¼ $.76 23 07283 Washer, ¼ $.76 24 3576 Drain plug $4.60 25 074629 Gasket $.76 27 varies Motor, supply HP, volts, & ph POR 28 varies Impellor, supply HP $4.58 2 www.commercialaquaticsupplies.com Phone: 604.980.282 Fax: 604.980.096 Toll Free Line:.800.663.5905

Whisperflow pumps with built in Variable Speed drives The motors used in these pumps are permanent magnet motors for maximum efficiency, and are TEFC for water protection. CSA approved. Model # Description Price 0055 0-3HP, 230v & ph, 8 speeds w/timers $804.95 007 0-3HP, 230v & ph, infinite speeds & $965.50 built Safety Vacuum Release System 002 0-3HP, 230v & ph, infinite speeds & $2384.79 can be set to maintain a flow rate Variable Frequency Drives (VFD) VFD solutions for your facility. Their purpose is to maximize the energy efficiency of your motors by only feeding the energy required to meet your designed flow rates. As an example a 20% reduction in pump speed will yield you an approximate 50% reduction in energy usage. Any facility that uses valves to throttle a too large pump or one that runs at a higher flow rate than mandated by the health authorities can benefit from this technology. VFD s can be tied directly to flow meters that have digital output so that they can adjust flow on the fly during the filter cycle. They also can have optional communication modules to connect to BMS systems through common protocols. Many models also incorporate ramping on start up (or soft start) which reduces air hammer and pressure issues downstream. This can prolong the life of other equipment like filters in your facility. For quotes on options not listed below please call with your requirements. Lenze SMV Series Features: NEMA (IP3) Indoor Enclosure, programmable, output relay, 3 digital inputs, analog input, (0-0v or 4-20ma), analog output. Model No HP Description Price ESV420N02TXB 5HP Lenze SMV Series, 240v, 3ph POR ESV552N02TXB 7.5HP Lenze SMV Series, 240v, 3ph POR ESV752N02TXB 0HP Lenze SMV Series, 240v, 3ph POR ESV3N02TXB 5HP Lenze SMV Series, 240v, 3ph POR ESV53N02TXB 20HP Lenze SMV Series, 240v, 3ph POR ESV402N04TXB 5HP Lenze SMV Series, 480v, 3ph POR ESV552N04TXB 7.5HP Lenze SMV Series, 480v, 3ph POR ESV752N04TXB 0HP Lenze SMV Series, 480v, 3ph POR ESV3N04TXB 5HP Lenze SMV Series, 480v, 3ph POR ESV53N04TXB 20HP Lenze SMV Series, 480v, 3ph POR ESV402N06TXB 5HP Lenze SMV Series, 575v, 3ph POR ESV552N06TXB 7.5HP Lenze SMV Series, 575v, 3ph POR ESV752N06TXB 0HP Lenze SMV Series, 575v, 3ph POR ESV3N06TXB 5HP Lenze SMV Series, 575v, 3ph POR ESV53N06TXB 20HP Lenze SMV Series, 575v, 3ph POR Options available: NEMA 4X, (IP65) enclosures, disconnect switches, other voltages, more interconnect features. Brands available: Lenze, ABB, Pentair, & Neptune Benson LENZE SMV LENZE SMV IN IP3 ENCLOSURE LENZE SMV IN IP65 WITH OPTIONAL DISCONNECT LENZE VFD IN IP65 ENCLOSURE Toll Free Line:.800.663.5905 Fax: 604.980.096 Phone: 604.980.282 www.commercialaquaticsupplies.com 3

HAYWARD PUMPS & PARTS Hayward HCP 2000 (Tristar) Pumps These are very efficient pumps with all-plastic construction. The strainer lid is clear, and comes off by hand. Suction and discharge are 2, and unions are included. The included unions fit 2 pipe inside and 2 ½ pipe outside. Self-priming to 0 above water level. From ½ HP to ½ HP the standard motors are 5/208-230 volt and single phase and 2 thru 5 HP have 208-230 volt single phase motors. All models are available in 208/230/4603 phase and 575 volts and 3 phase, on special order. Item No. Description Price SP3205EE Tristar /2hp 5/208/230 ph $644.67 SP3207EE Tristar 3/4hp 5/208/230 ph $72.86 SP320EE Tristar hp 5/208/230 ph $770.02 SP325EE Tristar /2hp 5/208/230 ph $846.59 SP3220EE Tristar 2hp 208/230 ph $058.40 SP3230EE Tristar 3hp 208/230 ph $270.20 SP3250EE Tristar 5hp 208/230 ph $2020.46 HCP3205C Tristar /2hp 575v 3ph $905.04 HCP3207C Tristar 3/4hp 575v 3ph $030.95 HCP320C Tristar hp 575v 3ph $033.55 HCP325C Tristar /2hp 575V 3ph $59.95 HCP3220C Tristar 2hp 575v 3ph $338.5 HCP3230C Tristar 3hp 575v 3ph $556.30 HCP3250C Tristar 5hp 575v 3ph $2027.5 Item No. Drwg # Description Price SPX3200UNKIT Union Connector, 3 piece $63.25 SPX3200UG 2 Union Gasket, 2 pkg $7.20 SPX3200A 3 Strainer Housing $408.38 SPX3200DLS 4 Strainer Cover, w 0-ring $03.5 SPX3200S 5 Strainer Cover 0-ring $8.48 SPX3200M 6 Strainer Basket $23.28 SPX3200Z8 7 Diffuser Screws (2) $7.75 SPX4000Z 8 Diffuser 0-ring $23.28 SPX3200B3 9 Diffuser $50.02 SPX3200Z 0 Impellor Screw $9.9 SPX302R Impellor Ring $0.02 SPX3205C 2 Impellor ½ hp, w/screw $45.47 SPX3207C 2 Impellor ¾ hp, w/screw $45.47 SPX320C 2 Impellor hp, w/screw $4.78 Tristar Replacement Parts Item No. Drwg # Description Price SPX325C 2 Impellor.5 hp, w/screw $55.44 SPX3220C 2 Impellor 2 hp, w/screw $65.8 SPX3230C 2 Impellor 3 hp, w/screw $65.8 SPX3230C5 2 Impellor 5 hp, w/screw $72.07 SPX3200SA 3 Mechanical Seal, #PS-3890 $20.66 SPX3200T 4 Housing O-ring $.93 SPX3200E 5 Seal Plate $67.65 SPX3200Z2 6 Housing Insert/spacer kit $3.08 SPX3200Z3 7 Housing Bolt $6.38 SPX3200Z5 8 Motor Bolt $2.3 SPX4000FG 9 Drain Plug w/o-ring $7.34 SPX3200GA 20 Motor Support Bracket $63.22 SPX3200WF 2 Motor Support Bracket $53.20 SPX3200SR 22 Motor Support Bracket $53.20 Motors-Please enquire 4 www.commercialaquaticsupplies.com Phone: 604.980.282 Fax: 604.980.096 Toll Free Line:.800.663.5905

Hayward HCP 3000 Series Pumps These Hayward pumps are 3 suction by 3 discharge and available in 2 thru 7.5 HP. The strainer is 3 flanged and bolt on. This pump is very efficient and quiet and all motors are TEFC for reliability. The 2, 3 & 5HP are available in 208-230 single phase, and all pumps are available in 208-230/460 v & 3ph, or 575v & 3ph. Item No. Description Price HCP3020 2 HP 208-230v ph POR HCP3030 3HP 208-230v ph POR HCP3050 5HP 208-230v ph POR HCP30703 7HP 230/460v 3ph POR HCP30703C 7HP 575v 3ph POR 208-230/460v 3ph & 575v 3ph quoted on request HCP 3000 Pump Parts Item No. Drwg # Description Price HCXP3000UNKIT Union Connector Kit $ HCXP3000UG 2 Union Gasket $ HCXP3000H 3 Strainer Housing w/plug $ HCXP3000DLS 4 Cover, lock ring & o-ring $ SPX4000S 5 Cover o-ring $ HCXP3000M 6 Strainer basket $ HCXP3000Z3 7 Strainer bolt/washer set of 4 $ HCXP343V70 8 Flange o-ring $ HCXP3000A 9 Pump housing w/plug $ HCXP338V60 0 Diffuser o-ring $ SPX2700z3SSPAK4 Diffuser screws (4) $ HCXP3000B_ 2 Diffuser, specify hp $ SPX3200Z 3 Impellor screw $ HCXP300_R 4 Impellor ring, specify hp $ HCXP30 C 5 Impellor w/screw specify hp $ HCXP4000SAV 6 Shaft Seal Assembly $ HCXP369V70 7 Pump Housing o-ring $ HCXP3000E 8 Seal plate $ SPX3200Z2 9 Housing insert (6) $ SPX3200Z3 20 Housing bolt $ SPX3200Z34PAK4 2 Motor bolt (4) $ SPX4000FG 22 Drain plug w/o-ring $ Other parts & motors on request Toll Free Line:.800.663.5905 Fax: 604.980.096 Phone: 604.980.282 www.commercialaquaticsupplies.com 5

Hayward HCP 4000 Series Commercial Self Priming Pumps These Hayward pumps are available in 5.5, 7.5, 0 and 2.5HP, and all are available in 230/460v 3ph or 575v 3ph. Note the 575v 3ph are special order. These pumps are all-plastic, with 4 suction and 4 discharge ports. The strainer lid is clear and removes by hand. These pumps are designed for medium head/high flow situations. Do not use where high head is required. A quiet and very efficient pump if properly sized. Replacing an old VM Series pump, and looking to get all plastic; this would be a good replacement. Item No. Description Price HCP55 5.5hp 230/460v 3ph $528.25 HCP75 7.5hp 230/460v 3ph $6000.69 HCP00 0hp 230/460v 3ph $6342.43 HCP25 2.5hp 230/460v 3ph $6757.72 HCP55C 5.5hp 575v 3ph $5628.6 HCP75C 7.5hp 575v 3ph $6438.98 HCP00C 0hp 575v 3ph $6565.95 HCP 4000 Series Pump Parts Item No. Drwg # Description Price HCXP6000A Strainer Lid Bolt & nut set (4) $20.77 HCXP600A 2 Strainer Cover c/w gskt $384.32 HCXP604A 3 Cover o-ring $2.82 HCXP6002A 4 & 5 Strainer Basket c/w handle $443.39 HCXP603A 7 & 8 Strainer drain plug w/o-ring $20.03 HCXP6022A 9 & 22 Strainer Body c/w o-ring $492.99 HCXP60A 0 & 22 & 23 Pump Casing /w o-rings $947.46 HCXP6004A Seal Set,, 4, 5, 6, 37 $57.25 HCXP6005A 2 & 45 Diffuser w/screws 5.5 & 7.5hp $352.32 HCXP6006A 2 & 45 Diffuser w/screws 0 & 2hp $352.32 HCXP60 3 Imp, specify HP, w/#36 & 37 $634.0 HCXP607A 7 Seal Plate Set,4,5,6,7,37,4 $396.22 HCXP608A 3 & 38 & 39 Seal Plate screw set $84.60 HCXP602A 8 & 48 & 49 Pump Support $4.37 HCXP609A 24 & 25 Union Set (2) w/gskt $394.56 HCXP602A 32 & 35 Bolt set (4) w/o-ring #23 $92.48 HCXP6023A 34 & 43 & 47 Pump Support Bolt Set (4) $49.34 Motors on request 6 www.commercialaquaticsupplies.com Phone: 604.980.282 Fax: 604.980.096 Toll Free Line:.800.663.5905

Jacuzzi Series VM Filter Pumps Series VM Self-Priming Filter Pumps incorporate several important features which contribute to good performance and long life. Double-volute casing allows rapid air separation and water circulation during the priming cycle and reduces the radial thrust on the impeller. Closed impeller is mounted on the motor shaft and requires no adjustment to maintain performance. Mechanical shaft seal requires no attention and is ideal for continuous operation without supervision. Flanged suction and discharge connections. 4" x 3". Very efficient pumps that move a lot of water for the horsepower. Recommended for use with fibreglass filters because of the low shut-off head 45 PSI. Model HP Price 5VMC-S2 5 $4065.80 75VMC-S2 7/2 $563.40 0VMC-S2 0 $6088.20 5VMC-T 5 $3729.80 75VMC-T 7/2 $4287.40 0VMC-T 0 $4677.00 5VMC-T5 5 $3729.80 75VMC-T5 7/2 $4287.40 0VMC-T5 0 $4677.00 5VMB-S2 5 $550.60 75VMB-S2 7/2 $6790.60 0VMB-S2 0 $7533.00 5VMB-T 5 $4872.20 75VMB-T 7/2 $5429.80 0VMB-T 0 $5920.20 5VMB-T5 5 $4872.20 75VMB-T5 7/2 $5429.80 0VMB-T5 0 $5920.20 Model S2 = 230 volts, single phase Model T = 208-230/460 volts, 3 phase Model T5 = 575 volts, 3 phase VMC = Cast iron pump VMB = cast bronze pump PERFORMANCE DATA Pump Model Total Head in Feet Shut Off 40 45 50 55 60 65 70 75 80 85 90 95 00 Head Feet/PSI 5VM 35 295 270 245 220 85 30 77/33 75VM 365 345 320 295 270 245 95 45 92/40 0VM 400 375 355 330 295 250 20 70 09/47 Jacuzzi VM Parts Pricing Part No Dia # Price Varies # Motor POR 22-0727.06 #2 Flinger $0.5 Bracket 02-2500-09 #3 5VMC-S2, T, T5, & 75VMC-T, T5 $45.5 02-250-07 75VMC-S2, 0VMC-S2, T, T-5 $924.05 02-2500-7 5VMB-S2, T, T5 & 75VMB-T, T5 $53.25 02-250-5 75VMB-S2, 0VMB-S2, T, T5 $88.85 4-293-24R4 #4 Hex Cap Screw 3/8-6 X 7/8 L $5.35 5 & 7 /2 VM 4-Pack 4-330-29R4 Hex Cap Screw ½-3 X /4 L - 4-Pack 0 VM $9.25 Parts pricing continues on next page Toll Free Line:.800.663.5905 Fax: 604.980.096 Phone: 604.980.282 www.commercialaquaticsupplies.com 7

9 9 9 3 2 5 8 4 ENLARGED VIEW OF SHAFT SLEEVE AND MECHANICAL SEAL AREA. Wet Ends VMB w/short bracket $397.76 VMB w/long bracket $4407.48 VMC w/short bracket $2938.32 VMC w/long bracket $3428.04 Short Bracket Models: All 5VM s, 75VM-T & 75VM-T5 Long Bracket Models: All 0 VM s & 75VM-S-2 6 5 7 Jacuzzi VM Parts Pricing Part No Dia # Price Sleeve 08-000-00 #5 5VMC-S2, T, T5 & 75VMC-T, T5 $77.87 5VMB-S2, T, T5 &75VMB-T, T5 08-0328-07 75VMC-S2 & 0VMC-S2, T, T5 $95.38 75VMB-S2 &0VMB-S2, T, T5 47-0022-09 #6 O-ring x -/8 $2.68 0-0369-03 #7 Mechanical Seal Assembly 0-0369-03 (PS-222) $82.5 4-029-0 #8 Washer $32.25 4-2055-04 #9 Shim X.03 $4.38 4-2055-2 Shim X.020 $4.38 4-2055-20 Shim X.00 $4.38 Impellor 05-8009-7 #0 5VMB $589.25 5VMC Use 5VMB NLA 75VMC-S2 Use 75VMB-52 NLA 75VMC-T, T5 Use 75VMB-T, T5 NLA 05-8045-3 75VMB-S2 $589.25 05-800-4 75VMB-T, T5 $589.25 0VMC Use 0 VMB NLA 05-8046-2 0VMB $589.25 4-0504-3 # Adaptor $48.85 4-0382-0 #2 Dowel Pin $0.79 22-0559-09 #3 Gib Key $8.75 4-0722-0 #4 Washer $.34 4-2493-04 #5 Cap Screw 3/8-6 X L $5.80 Case with Wear Ring & Plug 03-906-00 #6 VMC $07.36 03-906-8 VMB $2225.66 08-00-09 #7 Wear Ring $38.25 3-0059- #8 Plug ¼ NPT Galv, VMC $3.60 3-0059-29 Plug ¼ NPT Brass, VMB $4.95 3-09-04 #9 Gasket $2.95 4-205-03 #20 Index Pin $.6 3-223-04 #2 Gasket $0.40 Strainer Body 39-0647-04 #22 VMC $026.72 39-0647-2 VMB $228.90 4-0005-09 #23 Grommet -8 Pkg $27.0 Hex Cap Screw 3/8-6 X 7/8 L 4-293-24R8 #24 VMC -8 /Pkg $8.30 4-293-6R8 VMB-8/Pkg $.62 6-0707-08 #25 Strainer Basket $428.55 Strainer Cover 39-0648-03 #26 VMC $203.56 39-0648- VMB $294.65 3-0059- #27 Plug ¼ NPT-Galv, VMC $3.60 3-0059-29 Plug ¼ NPT- Brass VMB $4.95 47-0442-0 #28 O-ring 7-/4 X 7-3/4 $8.95 39-0646-05 #29 Lock Knob Assembly, pair $54.85 2-068-00 #30 Base 5VM, 75VM-T $53.56 2-068-8 75VM-S2, 0 VM $253.55 4-294-23 #3 Hex cap screw 3/8-6 X L 4-Pkg $7.5 4-0722-9 #32 Washer 3/8-4/Pkg $3.60 8 www.commercialaquaticsupplies.com Phone: 604.980.282 Fax: 604.980.096 Toll Free Line:.800.663.5905

Hydro 5000 Self Priming C. I. Pump by Waterco This pump is self priming, the impellor is bronze, and the cast iron volute is epoxy coated. 6 suction by 4 discharge. Waterco s 2 year warranty applies. The strainer is not included and must be ordered separately. Item No Description Price 9B05000 Hydro 5000 7.5 HP 208/230V/460V & 3 Ph $4526.96 9B05000-575 Hydro 5000 7.5 HP 575V & 3Ph $4583.76 9B0500 Hydro 5000 0 HP 208/230/460V & 3Ph $485.25 9B0500-575 Hydro 5000 0 HP 575V & 3Ph $50.89 9B05002 Hydro 5000 5 HP 208/230/460V & 3Ph $5269.62 9B05002-575 Hydro 5000 5 HP 575V & 3Ph $544.44 9B05003 Hydro 5000 20 HP 208/230/460V & 3Ph $5996.66 9B05003-575 Hydro 5000 20 HP 575V & 3Ph $6443.25 HYDRO 5000 SELF PRIMING C. I. PUMP Hydro 5000 Commercial Strainer by Waterco This strainer and basket are made from polypropylene and the lid is clear polycarbonate. The locking ring has handles so it can be removed by hand. The ports are 6 flanged and it can be used on the Hydro 5000 pump or any other pump that has a 6 suction flange. This strainer is rated for 673 GPM flow and a maximum working pressure or 5 PSI. Item No Description Price 9B05008-PP Strainer 6 - Polypropylene $967.02 Clear Polycarbonate Lid Locking Ring with handles foreasy removal 6" Flanged Ports Molded 6L Polypropylene Basket Glass filled Polypropylene Housing HYDRO 5000 COMMERCIAL STRAINER Hydro 5000 Strainer Parts Dia # Part # Description Price 63450580 PP Strainer Housing POR 2 63450500 Lid 2 Clear POR 3 62027 Lid O-ring BS452A POR 4 620232 Lock Ring 2 POR 5 63450520 Basket PP POR 6 63402302 Drain Plug ¼ BSP POR 7 62093 Drain Plug O-ring BS2 POR 8 620232 Handle POR 9 AXFI68 CF Knob POR Toll Free Line:.800.663.5905 Fax: 604.980.096 Phone: 604.980.282 www.commercialaquaticsupplies.com 9

Hydro 5000 Pump Parts Dia# Part # Description Price 9B500 Pump Housing POR 2 9B50 Drain Plug ¼ NPT POR 3 9B502 Drain Plug ½ NPT POR 5 9B504 Cap Screw 3/8-6 x POR 5A 9B5037 Cap Screw ½ -3 x POR 6 9B505 Seal Washer 7.5, 0, & 5 HP POR 6A 9B506 Seal Washer 20 HP POR 7 9B507 Impeller Gasket 7.5, 0, & 5 HP POR 7A 9B508 Impeller Gasket 20 HP POR 8 9B509 Impeller Washer 7.5, 0, & 5 HP POR 8A 9B5020 Impeller Washer 20 HP POR 9 9B502 Impeller 7.5 HP POR 9A 9B5022 Impeller 0 HP POR 9B 9b5023 Impeller 5 HP POR 9C 9B5024 Impeller 20 HP POR 0 9B5025 Volute Gasket POR 9B5026 Sleeve Gasket 7.5, 0, & 5 HP POR A 9B5027 Sleeve Gasket 20 HP POR 2 9B5028 Shaft Sleeve 7.5, 0, & 5 HP POR 2A 9B5029 Shaft Sleeve 20 HP POR 3 9B5030 Retaining Ring 7.5, 0, &5 HP POR 3A 9B503 Retaining Ring 20 HP POR 4 9B5032 Mechanical Shaft Seal 7.5, 0, & 5 HP POR 4A 9B5033 Mechanical Shaft Seal 20 HP POR 5 9B5034 Stud ½ - 3 x ½ POR 6 9B5038 ½ Lock Washer POR 7 9B5036 Nut ½ 3 POR 8 9B504 Cap Screw 3/8-6 x (7.5 HP) POR 8A 9B5037 Cap Screw ½ - 3 x POR 9 9B5035 3/8 Lock Washer (7.5 HP) POR 9A 9B5038 ½ Lock Washer POR 20 9B5039 Pump Bracket 7.5 HP POR 20A 9B5040 Pump Bracket 0, & 5 HP** POR 20B 9B504 Pump Bracket 20 HP POR Motors quoted on request, please provide HP, Volts & Phases POR ** This bracket is also used on 7.5HP Single Phase Pumps 20 www.commercialaquaticsupplies.com Phone: 604.980.282 Fax: 604.980.096 Toll Free Line:.800.663.5905

EQ Series Commercial Plastic Pump All-plastic pump and strainer for durability and long life. 6 suction on strainer and pump, and 4 discharge on pump. Direct replacement for C Series Bronze Pump. Can be purchased/used with or without strainer. Self priming with Hair and Lint Strainer. See-through strainer lid with cam and ramp closure. Very efficient and quiet operation. 208/230-460 3 phase is standard, other voltages (575) on request. Low shut-off head of 50 PSI, important for fiberglass filters rated at 50 PSI. Model Description H.P. Price 34003 EQK500w/strainer 5 H.P. $6282.47 340033 EQK750w/strainer 7.5 H.P. $6553.8 340034 EQK000w/strainer 0 H.P. $730.34 340035 EQK500w/strainer 5 H.P. $7624.94 EQ Series Parts-Strainer Dia. No. Part No. Description Price N/A 34003 Strainer complete,6 X 6 $265.30 5 3507 Clamp Cam & Ramp $566.5 4 356750 Lid EQ Clear $425.67 3 35066 EQ Lid Gasket $23.45 2 35784 EQ Strainer Basket $94.85 356725 EQ Strainer Pot $983.00 6 3576 Drain Plug $4.5 7 925 Drain Plug o-ring $.35 0 35003 Pot Flange O-ring $.25 9 356789 Flat Washer s/s /6 ID X -5/6 OD $.95 8 356788 Hex Bolt s/s 5/8 - X -3/4 $.55 N/S 350087 Pressure Relief Valve ¼ $7.85 5 4 3 2 EQ Series Parts-Pump 7 356790 Motor Adaptor $85.60 8 075842 Washer s/s Flat ½ X -/4 $.75 9 350063 Lock Washer s/s ½ Set of 4 $7.50 0 354290 Bolt s/s 3/8-6 X Set of 4 $0.85 35670 Bolt s/s 5/8 - X 6 /2 Set of 4 $43.0 2 356789 Washer s/s /6 X -5/6 Set of 4 $.95 3 356795 Seal Plate $963.90 4 7725 Seal Set PS-360 $52.00 5 350030 Impellor-EQ500 $402.25 5 350029 Impellor-EQ 750 $429.05 5 350028 Impellor-EQ 000 $455.87 5 350027 Impellor-EQ 500 $509.50 6 07037 Bolt s/s 3/8-6 X $6.75 7 350032 Diffuser-EQ500 $660.80 7 350033 Diffuser-EQ 750 &000 $708.55 7 356735 Diffuser-EQ 500 $536.30 8 5008500 Washer s/s Flat ¼ $4.25 9 07272 Washer s/s Lock ¼ $0.35 20 350035 Screw s/s ¼ -20 X ½ Set of 4 $5.65 0 9 8 7 6 Fits model EQ 500 only 20 356797 Screw s/s ¼ -20 X ¾ Set of 4 $6.95 2 350037 Diffuser O-ring $9.45 22 356755 Volute (housing) $2900.50 23 356776 Nut brass 5/8 - Set of 5 $8.30 24 3576 Drain Plug $4.50 25 925 O-ring for Drain Plug $.35 26 350060 Dowel Pin s/s 5/6 X ¾ (pair) $26.85 28 356780 Seal Plate O-ring $57.70 Toll Free Line:.800.663.5905 Fax: 604.980.096 Phone: 604.980.282 www.commercialaquaticsupplies.com 2

C Series Commercial Brass Pump WITH HAIR AND LINT POT Brass volute and pot, coated cast iron foot, flanged connections, 6 inch suction, 4 inch discharge. Large commercial pump with stainless steel basket. Easy serviceability. All-bronze construction for strength and durability. 6" suction and 4" discharge for maximum capabilities. Self-priming to ensure proper filtration. Heavy gauge stainless steel strainer basket with an open area 4 times the area of the suction port. Closed impeller for longer motor bearing life. Heat-resistant seal capable of operation at up to 200 0 F. Also available in 200/208V, 3 phase and 575V, 3 phase. One year warranty. Low shut off head 60 PSI. Model Description H.P. Price 0657 CHK 50 5 H.P. POR 0658 CHK 75 7 /2 H.P. POR 0659 CHK 00 0 H.P. POR 0660 CHK 50 5 H.P. POR 066 CHK 200 20 H.P. POR 208/230/460 3 ph quoted above C-Series Parts Dia. No Part No Description Price 075280 Bronze Knob $44.37 072747 Pot Assembly $6653.00 2 075275 Strainer Lid $047.00 3 07433 Cover O-ring #452 $7.45 4 0755 Bronze plug ¼" $5.95 5 07527 Pot Only $5040.00 6 072795 SS Basket $500.54 7 075273 Volute $4972.00 8 070943 5" Flange Gskt $30.84 9 07683 Screw 4 req. $38.52 0 075287 Foot Coated $0.79 07688 Screw 2 req. $2.02 2 07037 Impellor Lock Screw $6.84 3 07048 Impellor Washer $5.47 4 07573 Impellor Washer Gskt $.6 5 07---- Impellor: Note- Order Must include model, $642.00 (CH or CM), HP, Volts, & Phases 6 07725 Mechanical Seal $56.42 7 070906 Flange $75. 8 07423 O-ring $4.00 9 0768 Screw 2 req. $.5 20 07285 Water Slinger $0.62 2 07046 Impellor Key $26.90 22 07687 Screw 4 req. $6.68 22 www.commercialaquaticsupplies.com Phone: 604.980.282 Fax: 604.980.096 Toll Free Line:.800.663.5905

REPLACEMENT STRAINERS Custom Fibreglass & PVC Strainers Our custom strainers are suitable for both new installations and replacement of older strainers. Custom strainers save time and money for replacement applications since each one can be built to fit existing plumbing. Strainers are supplied with Vanstone flanges for inlet and outlet connections, an extra long basket to extend run between cleanings, air bleed valve and clear lid. These work well replacing old Hayward and Jacuzzi cast iron strainers as they rust out. Item No Pipe Size Price 34 07 2" $625.00 34 0 2 /2" $625.00 34 02 3" $645.00 34 03 4" $765.00 34 04 6" $2098.95 34 05 8" $2865.00 34 06 0" $405.00 Custom Heavy Duty Fiberglass and PVC strainer Ordering A Custom Strainer Fabricating a strainer to fit existing piping requires just three measurements plus flange sizes for each side. When you place an order we ll fax a diagram with dimensions to be filled in. If fitting existing plumbing is not a consideration, a standard strainer can be made without any additional information. Jacuzzi End-Suction Centrifugal Pumps These pumps were the industry standard for 30 years due to their efficiency, reliability and ease of service. Replacement pumps and parts are still available. The most common sizes are shown below. Larger pumps and parts are quoted on request. Inlet & outlet can be straight through or offset as required to match existing plumbing Larger pumps, up to 75hp quoted on request. Model No SxD RPM Price R5FL6 8" x 6" 750 POR R75FL6 8" x 6" 750 POR R0FL6 8" x 6" 750 POR R5FL6 8" x 6" 750 POR R20FL6 8" x 6" 750 POR R25FM6 8" x 6" 750 POR Automatic Pump Shutoff Device The Emotron PSP20 works by using the motor as the sensor, detecting the change in motor load caused by suction blockage and shutting down the pump motor in second. Installation is simple, electrical only. There is also no need to disable the device during backwashing or pool vacuuming. The Emotron Panel installs between the pump power supply and the pump. Three pieces of information are required to price and order these items. The motor supply voltage & number of phases and the motor full load amps. Priced on Request. B & G PUMP MODEL # 53 B & G (Bell & Gossett) Pumps quoted on request. Toll Free Line:.800.663.5905 Fax: 604.980.096 Phone: 604.980.282 www.commercialaquaticsupplies.com 23

Wide Bodied Strainers These Wide Bodied Hair and Lint strainers are made from Fiberglass reinforced PVC. They feature one piece 36 Stainless Steel baskets,.25 perforated, which are round with an angled top and handle. Lids are clear acrylic and see-through, with stainless steel and PVC hand knobs. Lid bolts swivel where required for easy removal. The Flanges are Vanstone, free to rotate to make alignment problem free. Configurations can be straight through, offset, or reducing as required. Flange to flange dimensions can be stock; or custom where this is a replacement strainer, to avoid changing plumbing. Due to the wide body these have a very low pressure drop and are typically lower in height than other strainers and suitable for restricted height spaces. For sizes not listed please enquire. Custom made to order. FOB North Vancouver. Item No Description Price 34 50 4 Flanged Strainer $2,98.20 34 5 6 Flanged Strainer $2,682.40 34 52 8 Flanged Strainer $3,248.0 34 53 0 Flanged Strainer $3,992.30 34 54 2 Flanged Strainer $4,6.0 Nemato/National Replacement Rectangular Profile Gasket Gasket is white rubber, 7/32 H X /32 W by cut length. Item No Description Price 575-53023 #6 H & L Strainer Lid Gasket, cut length 20 ½ POR 575-53024 #0 H & L Strainer Lid Gasket, cut length 32 ¾ POR 575-53025 #6 H & L Strainer Lid Gasket, cut length 5 3/8" POR 575-025MG Horizontal Manhole Gasket, cut length 48 3/8 POR Currently no National/Nemato products are available, the following are available in the interim. PKG # 3 of gasket material and tube of gasket glue $85.00 PKG #2 4 ½ of gasket material and tube of gasket glue $5.00 Nemato Strainer Lid Knobs, J-Bolts, & Fender Washers 34 64 Knob-Thru Hole w/brass insert, 3/8-6 $3.95 34 65 J-Bolt 3/8-6 by 6 stainless steel $0.95 34 66 Fender Washer stainless steel $2.50 34 67 U-Channel for SS Mesh Edges $8.75/foot 34 68 Clear Acrylic Lid for NSS-0-xxxx $43.00 34 69 Clear Acrylic Lid for NSS-6-xxxx $795.00 as per our specs only - to be approved Unions-Praher Thread by Slip Unions with O-ring seals Some products like pumps and dial valves come with plumbing ports that have female pipe threads. Normally pipe threads are tapered, and the threads get larger the more you screw them in to help them seal and be water tight. This can cause pump volutes, strainer, or dial valve bodies with threaded ports to crack or split. These unions are designed to prevent this, the threads are straight, and there is an o-ring to seal. When installing new pumps or dial valves these can be useful accessories to facilitate servicing and prevent damage to equipment. The Hi Temp models are for heaters. Item No Description Price 50-903 ½ slip/mipt, c/w O-ring $7.95 50-906 ½ slip/mipt, c/w O-ring, hi temp $6.38 200-903 2 slip/mipt, c/w O-ring $6.38 200-906 2 slip/mipt, c/w O-ring, hi temp $23.38 Hayward PVC Y Strainers These are rated at 50 PSI, have viton seals, the plastic screen has /32 openings, and they are suitable for both horizontal and vertical installation. A hex cap provides easy access to plastic screen. All come with socket end connections. For use wherever systems need protection from possible sand leaks to prevent clogging. (ie Chlorinators). Item No Description Price YS050SE ½ Y Strainer $245.45 YS0200SE 2 Y Strainer $287.25 YS0250SE 2 ½ Y Strainer $456.00 YS0300SE 3 Y Strainer $576.75 YS0400SE 4 Y Strainer $94.50 24 www.commercialaquaticsupplies.com Phone: 604.980.282 Fax: 604.980.096 Toll Free Line:.800.663.5905