Siemens AG 200 Overview vortex flowmeters provide accurate volumetric and mass flow measurement of steam, gases and liquids as an all-in-one solution with integrated temperature and pressure compensation. Benefits All devices have 2-wire technology and HART communication Temperature compensation for saturated steam as standard feature Integrated temperature and pressure measurement enabling direct compensation of density Pressure, temperature and flow can be read at a single point. No additional installation of pressure and temperature sensors Direct measurement of energy or energy consumption Optimum process reliability thanks to Intelligent Signal Processing (ISP) - stable readings, free of external perturbations Fully welded stainless steel construction with high corrosion, pressure and temperature resistance Maintenance-free sensor design Ready to use due to plug & play feature. No additional cabling work Minimal pressure drop Pressure and temperature compensation for fluctuating volume flows Measurement of comsumption in compressed air systems No risk of deposits or damage (sensor in the turbulent area) All units parameterized prior to delivery Application The is a compact flowmeter in a single or dual transmitter version, suitable for measuring industrial steam, gases, as well as conductive and non-conductive liquids. E.g. steam (saturated steam, superheated steam), industrial gases (compressed air, nitrogen, liquefied gases, flue gases), and conductive and non-conductive liquids (demineralized water, boiler feed water, solvents, heat transfer oil). The main applications of can be found in the following sectors: Chemical Petrochemical Oil & Gas Power plants - Air - Heating - Cooling - Chilling Food & beverage - Pharmaceutical - Sugar refineries - Dairies - Breweries - Production of soft drinks Refining Water & waste water System Overview Version Single transmitter Dual transmitter Options Standard Pressure sensor Flange Sandwich Pressure sensor and isola- Standard tion valve Function Operating Principle vortex flowmeters measure flow rate by detecting the frequency at which alternating vortices are shed from a bluff body inserted into the flow stream. This principle of measurement is known as Von Karman s vortex street principle: alternating vortices form behind an object in a stream. The frequency of the alternating vortices is proportional to the flow rate. The passage of a vortex causes a slight stress on a pick-up placed downstream of the bluff body. The stress is picked up and counted as pressure surges by a dual Piezo crystal placed inside the wing. Siemens FI 0 20 /365
Siemens AG 200 $ = Bluff Body, % = Pick-up The flowmeter calculates the flow velocity using the following equation: Q = A V = A d / St f = 0,93 f / K [m 3 /h] Where: Requirements In order to generate the vortex streets, the medium must have a minimum velocity: For steam and gases, the flow velocity must be 2 to 80 m/s (6.6 to 262 ft/s) For liquids the flow velocity must be 0. to 0 m/s (.3 to 32.8 ft/s) Design Q d Q = flow rate [m 3 /h] f = vortex shedding frequency [Hz] K = calibration constant [pulses/m 3 ] d = width of the bluff body [m] St = Strouhal Number A = cross-section area [m 2 ] V = flow velocity [m/s] volumetric and mass flowmeter is available in the following configurations: Single transmitter The single transmitter is available as a flange or sandwich solution in the following versions: Vortex standard flowmeter Measurement with integrated temperature sensor as standard feature Vortex flowmeter with pressure sensor Measurement with integrated temperature and pressure sensors for compensation of gases, wet gases, gas mixtures or steam (for engergy measurement). Vortex flowmeter with pressure sensor and isolation valve Allowing the pressure sensor to be shut off for the purpose of pressure or leak testing of the pipeline or for being exchanged without interrupting the process. Using the built-in two-way valve, the pressure sensor can also be calibrated and tested at a later time. Dual transmitter This is a genuine redundant system with two independent sensors and two converters providing twofold functional reliability and availability of the measurement. This variant is optimally suited for measurements in multi-product pipelines. The dual converter is available as: Vortex standard flowmeter Measurement with temperature sensor for saturated steam compensation as standard feature 2 Technical specifications Input Measuring range limits Media pressure Output Current output Measuring range See Dimensional Drawings... 00 bar (Higher pressures on request) 20 ma Over range 20.8 ma ± % (05 % ± %) Load - min. 00 Ω - max. R max = (U Power Supply - V)/22 ma Error signal NAMUR NE 3 Maximum output 22 ma (2.5 %) Multidrop mode Digital output Communication Physical layer Device category Pulse output (Passive pulse output, needs separate power supply. Pulse output has to be defined in the Option menu Y7 totalizer or energy unit has to be entered. E.g.: pulse/kg or pulse/0 m³) Pulse frequency Power supply ma HART FSK Transmitter Max. 0.5 Hz Min. 2 V DC as NAMUR or Non-Ex version open < ma, max. 36 V, closed 00 ma, U < 2 V Ex version open < ma, max. 30 V, closed 00 ma, U < 2 V Accuracy Standard version For liquids - Re 20 000 ± 0.75 % For steam and gases - Re 20 000 ± % For steam, gases and liquids - 0 000 < Re < 20 000 ± 2 % Pressure and temperaturecompensated version For liquids - 0 000 < Re < 20 000 ± 2 % - Re 20 000 ± 0.75 % For gases and steam - 0 000 < Re < 20 000 ± 2.5 % - Re 20 000 ±.5 % Repeatability ± 0, % Installation conditions (At different conditions, e.g. installation after control valve, bends or reductions, please refer to the operating instructions.) Inlet run Outlet run 20 x DN 5 x DN /366 Siemens FI 0 20
Siemens AG 200 Software Uncompensated for gases, steam and liquids, but temperature-compensated for saturated steam Density-compensated by temperature and pressure for superheated steam, no energy calculation Gross heat When the device has to operate as a energy calculation device In options Y5 to Y56 add information regarding: Order option Order option Order option 5 Y5 Variable current output Y52 Power unit Select one of the following units from power units table in Y52: kj/h, MJ/h, GJ/h, Btu/h, kcal/h, kw, MW or special (custom) Y53 Fullscale power value Y5 Variable pulse output Gases and wet gases Order option 7 Wet gases FAD - Free Air Delivery When the device has to operate close to a compressor In Y8 to Y87 add information regarding: Mixed gases Rated operation conditions Ambient temperature Non-Ex version Ex version Storage temperature Media temperature Density Viscosity Y55 Totalizer on/off Y56 Configures for totalizer select one of the following units from energy units table in Y56: kj, MJ, GJ, Btu th, kcal, kwh, MWh or special (custom). Select Y9 and enter relative humidity in % Order option 8 Y8 Inlet suction temperature Y82 Atmosphere pressure Y83 Pressure drop filter Y8 Inlet relative humidity Y85 Actual revolutions per minute (of compressor) Y86 Rated rpm of compressor Y87 Outlet relative humidity. This information is available from compressor supplier. When the fluid is a gas mixture, make an SDR request (sheet available on intranet) and fill in gas names and amount in % -0 +85 C (-0 +85 F) -0 +65 C (-0 +9 F) -50 +85 C (-58 +85 F) -0 +20 C (-0 +6 F) Taken into consideration when rating < 0 cp Reynolds number 0 000 2 300 000 Media pressure limit Max. 00 bar (Higher pressure on request. Make an SDR request, sheet available on intranet) Design Material Sensor: house/pick-up Housing: transmitter Sensor gaskets: for pick-up and pressure sensor Process connections.0(36l)/.35(36l) Hastelloy C22 available (make an SDR request, sheet available on intranet) Aluminium for increased requirements.35(36l)/fpm or FFKM FPM (Viton) by steam and non-aggressive gases. FFKM (Kalrez) by chlorine and other aggressive gases (only available together with a pressure sensor). Flange norm EN 092- form B/B2 or ASME B6.5 RF. Other flanges on request. Make an SDR request, sheet available on intranet Flange version DN 5 300 (½ 2") Sandwich version DN 5 00 (½ ") Degree of protection Dimensions and weights Display and operating interface Local display Languages Power supply Standard version Ex version Certificates and approvals Explosion protection ATEX IP66/IP67 See Dimensional Drawings 2 lines, 0 characters per line German, English, French 36 V DC 30 V DC II 2G EEx d ia [ia] IIC T6 FM US/C Class I, II, III, Div. and 2 Calibration Material Certificate Cleaning Certificates All flowmeters will be delivered with a 3 point calibration certificate Certificate of compliance, pressure test, material certificate, material in acc. of NACE and PMI of pressure bearing metal parts. Choose Cleaning Class when fluid is oxygen or contains chloride. X-ray test on pressurized weldings and dye penetration test on pressure bearing weldings Dye penetration test Siemens FI 0 20 /367
Siemens AG 200 Flanged Single transmitter and T max = 20 C (6 F) Connection size Sensor size DN 5 (½") DN 5 A DN 25 (") DN 25 2 B DN 0 (½") DN 0 2 K DN 50 (2") DN 50 2 R DN 80 (3") DN 80 3 L DN 00 (") DN 00 3 S DN 50 (6") DN 50 M DN 200 (8") DN 200 T DN 250 (0") DN 250 W DN 300 (2") DN 300 5 E Flange norm and nominal pressure Order No. Form B/B2 EN 092- PN 0 DN 200... 300 A PN 6 DN 50... 300 B PN 25 DN 200... 300 C PN 0 DN 5... 300 D PN 63 DN 50... 50 E PN 00 DN 5... 50 F RF ASME B6.5 50 lb ½... 2" J 300 lb ½... 2" K 600 lb ½... 6" L 7 ME 2 6 0 0 - Sensor material/gasket Stainless steel.0 (36L)/.35 (36L)/FPM Stainless steel.0 (36L)/.35 (36L)/FFKM 5 77777-7777 Transmitter design Compact, no cable Approval and cable gland Non Ex, M20 x.5 Non Ex, ½ NPT 2 ATEX, M20 x.5 ATEX, ½ NPT 5 FM US/C, M20 x.5 6 FM US/C, ½" NPT 7 Transmitter, display and communication With display, HART Pressure sensor and isolation valve Without pressure sensor A With pressure sensor, range: bar B 6 bar D 0 bar E 6 bar G 25 bar H 0 bar K 60 bar L 00 bar N With isolation valve and pressure sensor, range: bar P 6 bar Q 0 bar R 6 bar S 25 bar U 0 bar V 60 bar W 00 bar Y A Flanged Single transmitter and T max = 20 C (6 F) Software Uncompensated for gases, wet gases, steam and liquids, respectively, temperature compensation for saturated steam Density compensation for superheated steam Density compensation for superheated steam and 5 setting of Gross heat Opt. Y5... Y56 for Energy measuring Density compensation for gases and wet gases 7 and setting of Relative humidity at opt. Y9 Density compensation for gases, wet gases and 8 setting of FAD - free air delivery Opt. Y9 and Y8... Y87 for Compressor settings Accessories Operating instructions for English This device is shipped with a Quick Start guide and a CD containing further SITRANS F literature. All literature is also available for free at: http://www.siemens.com/flowdocumentation Order No. 7 ME 2 6 0 0-77777 -7777 A5E020023 /368 Siemens FI 0 20
Siemens AG 200 Order code Order code Further designs Please add -Z to Order No. and specify Order code. Converter housing material Aluminium for increased requirement, color: petrol green A0 Additional data Please add -Z to Order No. and specify Order code and plain text. Input process data Medium: Specify steam, gas, liquid or customised Y0 Material certificate Certificate of compliance EN 020-2. Pressure test + 3. accordance EN 020 Material certificate pressure parts + certificate 3. Material in accordance with NACE MR 075-0 PMI of pressure bearing metal parts + certificate 3. Material certificate pressure parts + PMI/certificate 3. Calibration certificate FX300 As standard the flow device has a 3-point calibration certificate. Calibration certificate (5 point) Hardness test Hardness test on pressure bearing parts + 3. Equotip LD procedure according to NACE MR 075-0 Cleaning for oil and fat Class increased requirement (customer-specified) and 3. (EN 020) Class 2 and 3. (EN 020) Certificates X-ray test on ppressure bearing weldings Dye penetration test on pressure bearing weldings Tag name plate Stainless steel tag with 3 mm characters, max. 2 x 8 characters (0 x 20 mm, add plain text) Stainless steel tag with 2,5 mm characters, max. 8 x 0 characters (20 x 6 mm, add plain text) C0 C C2 C3 C C5 D H30 K6 K8 M56 M58 Y7 Y8 Temperature: Specify max. operating temperature and units Pressure: Specify max. operating pressure and units Density; (only by customer-specified medium): Specify medium density and units Viscosity; (only by customer-specified medium): Specify medium viscosity and units Flow rate: Specify min./max. flow rate and units Setting of pulse output: Specify totalizer or energy unit ( pulse/unit) Relative humidity (amount in %) Settings of gross heat Variable current output Power unit (specify: kj/h, MJ/h, GJ/h, Btu/h, kcal/h, kw, MW or special(custom)) Fullscale power value Variable pulse output Totalizer on/off Configure totalizer (specify: kj, MJ, GJ, Btu th, kcal, kwh, MWh or special(custom)) Settings of FAD Inlet suction temperature Atmosphere pressure Pressure drop filter Inlet relative humidity Actual revolutions per minute (of compressor) Y Y2 Y3 Y Y5 Y7 Y9 Y5 Y52 Y53 Y5 Y55 Y56 Y8 Y82 Y83 Y8 Y85 Rated Rpm of compressor Y86 Outlet relative humidity This information is available from compressor supplier. Y87 Siemens FI 0 20 /369
Siemens AG 200 Sandwich Single transmitter and T max = 20 C (6 F) Connection size Sensor size DN 5 (½") DN 5 A DN 25 (") DN 25 2 B DN 0 (½") DN 0 2 K DN 50 (2") DN 50 2 R DN 80 (3") DN 80 3 L DN 00 (") DN 00 3 S Nominal pressure Order No. EN PN 6 DN 50... 00 B PN 0 DN 5... 00 D PN 63 DN 50... 00 E PN 00 DN 5... 00 F ASME 50 lb ½... " J 300 lb ½... " K 600 lb ½... " L 7 ME 2 7 0 0 - Sensor material/gasket Stainless steel.0 (36L)/.35 (36L)/FPM Stainless steel.0 (36L)/.35 (36L)/FFKM 5 77777-7777 Transmitter design Compact, no cable Approval and cable gland Non Ex, M20x.5 Non Ex, ½ NPT 2 ATEX, M20x.5 ATEX, ½ NPT 5 FM US/C, M20x.5 6 FM US/C, ½" NPT 7 Transmitter, display and communication With display, HART Pressure sensor and isolation valve Without pressure sensor A With pressure sensor, range: bar B 6 bar D 0 bar E 6 bar G 25 bar H 0 bar K 60 bar L 00 bar N With isolation valve and pressure sensor, range: bar P 6 bar Q 0 bar R 6 bar S 25 bar U 0 bar V 60 bar W 00 bar Y A Further designs Please add -Z to Order No. and specify Order code. Converter housing material Aluminium for increased requirement, color: petrol green Material certificate Certificate of compliance EN 020-2. Pressure test + 3. accordance EN 020 Material certificate pressure parts + certificate 3. Material in accordance with NACE MR 075-0 PMI of pressure bearing metal parts + certificate 3. Material certificate pressure parts + PMI/certificate 3. Calibration certificate FX300 As standard the flow device has a 3-point calibration certificate. Calibration certificate (5-point) Hardness test Hardness test on pressure bearing parts + 3. Equotip LD procedure according to NACE MR 075-0 Cleaning for oil and fat Class increased requirement (customer-specified) and 3. (EN 020) Class 2 and 3. (EN 020) Certificates X-ray test on pressure bearing weldings Dye penetration test on pressure bearing weldings Tag name plate Stainless steel tag with 3 mm characters, max. 2 x 8 characters (0 x 20 mm, add plain text) Stainless steel tag with 2,5 mm characters, max. 8 x 0 characters (20 x 6 mm, add plain text) Order code A0 C0 C C2 C3 C C5 D H30 K6 K8 M56 M58 Y7 Y8 Software Uncompensated for gases, wet gases, steam and liquids respectively temperature compensation for saturated steam Density compensation for superheated steam Density compensation for superheated steam and 5 setting of Gross heat Opt. Y5... Y56 for Energy measuring Density compensation for gases and wet gases 7 and setting of Relative humidity at opt. Y9 Density compensation for gases, wet gases and 8 setting of FAD - free air delivery Opt. Y9 and Y8... Y87 for Compressor settings /370 Siemens FI 0 20
Siemens AG 200 Additional data Please add -Z to Order No. and specify Order code and plain text. Input process data Medium: Specify steam, gas, liquid and customised Temperature: Specify max. operating temperature and units Pressure: Specify max. operating pressure and units Density: (only by customer-specified medium): Specify medium density and units Viscosity: (only by customer-specified medium): Specify medium viscosity and units Flow rate: Specify min./max. flow rate and units Setting of pulse output: Specify totalizer or energy unit ( pulse/unit) Relative humidity (amount in %) Settings of gross heat Variable current output Power unit (specify: kj/h, MJ/h, GJ/h, Btu/h, kcal/h, kw, MW or special(custom)) Fullscale power value Variable pulse output Totalizer on/off Configure totalizer (specify: kj, MJ, GJ, Btu th, kcal, kwh, MWh or special(custom)) Settings of FAD Inlet suction temperature Atmosphere pressure Pressure drop filter Inlet relative humidity Actual revolutions per minute (of compressor) Rated Rpm of compressor Outlet relative humidity This information is available from compressor supplier. Order code Y0 Y Y2 Y3 Y Y5 Y7 Y9 Y5 Y52 Y53 Y5 Y55 Y56 Y8 Y82 Y83 Y8 Y85 Y86 Y87 Siemens FI 0 20 /37
Siemens AG 200 Flanged Dual transmitter and T max = 20 C (6 F) Connection size Sensor size DN 0 (½") DN 0 2 K DN 50 (2") DN 50 2 R DN 80 (3") DN 80 3 L DN 00 (") DN 00 3 S DN 50 (6") DN 50 M DN 200 (8") DN 200 T DN 250 (0") DN 250 W DN 300 (2") DN 300 5 E Flange norm and nominal pressure Order No. Form B/B2 EN 092- PN 0 DN 200... 300 A PN 6 DN 50... 300 B PN 25 DN 200... 300 C PN 0 DN 0... 300 D PN 63 DN 50... 50 E PN 00 DN 0... 50 F 7 ME 2 8 0 0-77777 -7777 Further designs Please add -Z to Order No. and specify Order code. Converter housing material Aluminium for increased requirement, color: petrol green Material certificate Certificate of compliance EN 020-2. Pressure test + 3. accordance EN 020 Material certificate pressure parts + certificate 3. Material in accordance with NACE MR 075-0 PMI of pressure bearing metal parts + certificate 3. Material certificate pressure parts + PMI/certificate 3. Calibration certificate FX300 As standard the flow device has a 3-point calibration certificate. Calibration certificate (5-point) Hardness test Order code A0 C0 C C2 C3 C C5 D RF ASME B6.5 50 lb ½... 2" J 300 lb ½... 2" K 600 lb ½... 6" L Sensor material/gasket Stainless steel.0 (36L)/.35 (36L)/FPM Stainless steel.0 (36L)/.35 (36L)/FFKM 5 Transmitter design Compact, no cable Approval and cable gland Non Ex, M20x.5 Non Ex, ½ NPT 2 ATEX, M20x.5 ATEX, ½ NPT 5 FM US/C, M20x.5 6 FM US/C, ½" NPT 7 Transmitter, display and communication With display, HART Pressure sensor and isolation valve Without pressure sensor Software Uncompensated for gases, wet gases, steam and liquids respectively temperature compensation for saturated steam A A Hardness test on pressure bearing parts + 3. Equotip LD procedure according to NACE MR 075-0 Cleaning for oil and fat Class increased requirement (customer-specified) and 3. (EN 020) Class 2 and 3. (EN 020) Certificates X-ray test on pressure bearing weldings Dye penetration test on pressure bearing weldings Tag name plate Stainless steel tag with 3 mm characters, max. 2 x 8 characters (0 x 20 mm, add plain text) Stainless steel tag with 2,5 mm characters, max. 8 x 0 characters (20 x 6 mm, add plain text) Additional data Please add -Z to Order No. and specify Order code and plain text. Input process data Medium: Specify steam, gas, liquid and customised Temperature: Specify max. operating temperature and units Pressure: Specify max. operating pressure and units H30 K6 K8 M56 M58 Y7 Y8 Y0 Y Y2 Density; (only by customer-specified medium): Specify medium density and units Y3 Viscosity; (only by customer-specified medium): Specify medium viscosity and units Y Flow rate: Specify min./max. flow rate and units Y5 Setting of pulse output; Specify totalizer or energy unit ( pulse/unit) Y7 Relative humidity (amount in %) Y9 /372 Siemens FI 0 20
Siemens AG 200 Accessories or spare parts for Description Order No. Seal disc 2.8-2-0. A5E02839 Socket only for DN 5/25 ; /2" On request Description Service Toolbox for changing software (basic, steam and gas) and different settings in the electronic. Order No. A5E0237589 Socket only for DN 5/25 ; " On request Pickup.0 On request O-ring pickup A5E0286 O-ring for pressure screw 7.3 x 2.62-FPM-70 A5E02888 Pressure sensor /6/0/6/25/0/60/00 bar On request F) Subject to export regulations AL: 9I999, ECCN: N. Cover gasket O-Ring 9.67 x 3.5 A5E02892 Schematics Converter housing gasket 59,35,5-2-N O-ring DIN377-20 x -FPM for sensor O-ring 0x2-NBR for leadthrough A5E02895 A5E02855 A5E028525 DUBOX plug, 5-pole-RM2 A5E028527 Electronic Basic D-HART Steam D-HART A5E02853 A5E0285 2 3 2 Power supply Load - + ma Ampere meter, optional HART 3 A A+ B B+ Gas D-HART A5E0285 Load for HART communication Display Cable feedthrough 0-pole (non Ex). O-ring for cable feedthrough 2.89 x 2.62 0-pole plug Sensor replacement (incl. Seal disc, pickup, O-rings for pickup, and pressure screw DN 5 (incl. ½" socket) A5E028558 A5E028562 A5E028087 2 3 Power supply Load - + - + Counter ma 2 + - Ampere meter, optional HART 3 A A+ B B+ DN 25 (incl. " socket) A5E0286 Connection pulse output DN 0... 00 A5E02852 DN 50... 300 A5E0227505 F) Pressure sensor replacement (Incl. pressure sensor, DUBOX plug, 2 O-rings and calibration certificate) bar (58 psi) A5E02857 6 bar (87 psi) A5E02875 0 bar (5 psi) A5E02880 6 bar (232 psi) A5E02822 25 bar (363 psi) A5E028307 0 bar (580 psi) A5E02836 60 bar (870 psi) A5E028322 00 bar (50 psi) A5E02837 Siemens FI 0 20 /373
Siemens AG 200 Dimensional drawings a a D H L Flange version, frontal view, a = 33 mm (5.2 inches) Flange version, frontal view, a = 33 mm (5.2 inches) c b d Flange version, side view, b = 05 mm (.3 inches), c = 79 mm (7.05 inches) Flange version, side view, b = 05 mm (.3 inches), c = 79 mm (7.05 inches) a D H D H L c b l d L H Flange version, dual converter, specified weight + 2.80 kg (6.7 lb) /37 Siemens FI 0 20
Siemens AG 200 Flange version EN092- Size Pressure rating Dimensions [mm (inches)] Weight [kg (lb)] DN PN d D L H l Flowmeter (with pressure sensor) Flowmeter (without pressure sensor) 5 0 7.3 (0.68) 95 (3.7) 200 (7.87) 265 (0.3) (5.67) 6. (3.5) 5.5 (2.3) 5 00 7.3 (0.68) 05 (.3) 200 (7.87) 265 (0.3) (5.67) 7. (5.65) 6.5 (.33) 25 0 28.5 (.2) 5 (.53) 200 (7.87) 265 (0.3) (5.67) 7.9 (7.2) 7.3 (6.09) 25 00 28.5 (.2) 0 (5.5) 200 (7.87) 265 (0.3) (5.67) 9.9 (2.83) 9.3 (20.50) 0 0 3. (.70) 50 (5.9) 200 (7.87) 270 (0.63) (5.67) 0.8 (23.8) 0.2 (22.9) 0 00 2.5 (.67) 70 (6.69) 200 (7.87) 270 (0.63) (5.67).8 (32.63).2 (3.3) 50 6 5.5 (2.5) 65 (6.50) 200 (7.87) 275 (0.83) (5.67) 2.7 (28.00) 2. (26.68) 50 0 5.5 (2.5) 65 (6.50) 200 (7.87) 275 (0.83) (5.67) 2.9 (28.) 2.3 (27.2) 50 63 5.5 (2.5) 80 (7.09) 200 (7.87) 275 (0.83) (5.67) 6.9 (37.26) 6.3 (35.9) 50 00 53.9 (2.2) 95 (7.68) 200 (7.87) 275 (0.83) (5.67) 8. (0.57) 7.8 (39.2) 80 6 82.5 (3.25) 200 (7.87) 200 (7.87) 290 (.2) 5 (6.06) 7. (38.36) 6.8 (37.0) 80 0 82.5 (3.25) 200 (7.87) 200 (7.87) 290 (.2) 5 (6.06) 9. (2.77) 8.8 (.5) 80 63 8.7 (3.22) 25 (8.6) 200 (7.87) 290 (.2) 5 (6.06) 23. (5.59) 22.8 (50.27) 80 00 80.9 (3.9) 230 (9.06) 200 (7.87) 290 (.2) 5 (6.06) 27. (60.) 26.8 (59.08) 00 6 07. (.22) 220 (8.66) 250 (9.8) 30 (2.20) 6 (6.6) 22 (8.50) 2. (7.8) 00 0 07. (.22) 235 (9.25) 250 (9.8) 30 (2.20) 6 (6.6) 25 (55.2) 2. (53.79) 00 63 06.3 (.9) 250 (9.8) 250 (9.8) 30 (2.20) 6 (6.6) 30 (66.) 29. (6.82) 00 00 0.3 (.) 265 (0.3) 250 (9.8) 30 (2.20) 6 (6.6) 36 (79.37) 35. (78.0) 50 6 59.3 (6.27) 285 (.22) 300 (.8) 325 (2.80) 7 (6.85) 35.8 (78.93) 35.2 (77.60) 50 0 59.3 (6.27) 300 (.8) 300 (.8) 325 (2.80) 7 (6.85).8 (92.5).2 (90.83) 50 63 57. (6.9) 35 (3.58) 300 (.8) 325 (2.80) 7 (6.85) 59.8 (3.8) 59.2 (30.5) 50 00 5. (6.07) 355 (3.98) 300 (.8) 325 (2.80) 7 (6.85) 67.8 (9.7) 67.2 (8.5) 200 0 206.5 (8.3) 30 (3.39) 300 (.8) 350 (3.78) 9 (7.6) 38. (8.66) 37.8 (83.33) 200 6 206.5 (8.3) 30 (3.39) 300 (.8) 350 (3.78) 9 (7.6) 38. (8.66) 37.8 (83.33) 200 25 206.5 (8.3) 360 (.7) 300 (.8) 350 (3.78) 9 (7.6) 7. (0.50) 6.8 (03.8) 200 0 206.5 (8.3) 375 (.76) 300 (.8) 350 (3.78) 9 (7.6) 55. (22.) 5.8 (20.8) 250 0 260. (0.25) 395 (5.55) 380 (.96) 370 (.57) 22 (8.82) 58.0 (27.87) 57. (26.55) 250 6 260. (0.25) 05 (5.9) 380 (.96) 370 (.57) 22 (8.82) 59.0 (30.07) 58. (28.75) 250 25 258.8 (0.9) 25 (6.73) 380 (.96) 370 (.57) 22 (8.82) 75.0 (65.35) 7. (6.02) 250 0 258.8 (0.9) 50 (7.72) 380 (.96) 370 (.57) 22 (8.82) 93.0 (205.03) 92. (203.7) 300 0 309.7 (2.9) 5 (7.52) 50 (7.72) 395 (5.55) 2 (9.6) 76.3 (68.2) 75.7 (66.89) 300 6 309.7 (2.9) 60 (8.) 50 (7.72) 395 (5.55) 2 (9.6) 82.8 (82.5) 82.2 (8.22) 300 25 307.9 (2.2) 85 (9.09) 50 (7.72) 395 (5.55) 2 (9.6) 99.3 (28.92) 98.7 (27.60) 300 0 307.9 (2.2) 55 (20.28) 50 (7.72) 395 (5.55) 2 (9.6) 28. (282.) 27.5 (28.09) Siemens FI 0 20 /375
Siemens AG 200 Flange version ASME B6.5 Size Pressure rating Dimensions [mm (inches)] Weight [kg (lb)] DN class d D L H l Flowmeter (with pressure sensor) Flowmeter (without pressure sensor) ½ 50 5.8 (0.62) 90 (3.5) 200 (7.87) 265 (0.3) (5.67) 5. (.2).5 (9.92) ½ 300 5.8 (0.62) 95 (3.7) 200 (7.87) 265 (0.3) (5.67) 5.5 (2.3).9 (0.80) ½ 600 3.9 (0.55) 95 (3.7) 200 (7.87) 265 (0.3) (5.67) 5.7 (2.57) 5. (.2) 50 26.6 (.05) 0 (.33) 200 (7.87) 265 (0.3) (5.67) 6.8 (.99) 6.2 (3.67) 300 26.6 (.05) 25 (.92) 200 (7.87) 265 (0.3) (5.67) 7.8 (7.20) 7.2 (5.87) 600 2.3 (0.96) 25 (.92) 200 (7.87) 265 (0.3) (5.67) 8. (7.86) 7.5 (6.53) ½ 50 0.9 (.6) 25 (.92) 200 (7.87) 270 (0.63) (5.67) 8.9 (9.62) 8.3 (8.30) ½ 300 0.9 (.6) 55 (6.0) 200 (7.87) 270 (0.63) (5.67) (2.25) 0. (22.93) ½ 600 38. (.50) 55 (6.0) 200 (7.87) 270 (0.63) (5.67) 2 (26.6). (25.3) 2 50 52.6 (2.07) 50 (5.9) 200 (7.87) 275 (0.83) (5.67).6 (25.57) (2.25) 2 300 52.6 (2.07) 65 (6.50) 200 (7.87) 275 (0.83) (5.67) 3 (28.66) 2. (27.3) 2 600 9.3 (.9) 65 (6.50) 200 (7.87) 275 (0.83) (5.67).5 (3.97) 3.9 (30.6) 3 50 78 (3.07) 90 (7.8) 200 (7.87) 290 (.2) 5 (6.06) 20. (.97) 9.8 (3.65) 3 300 78 (3.07) 20 (8.27) 200 (7.87) 290 (.2) 5 (6.06) 23. (5.59) 22.8 (50.27) 3 600 73.7 (2.90) 20 (8.27) 200 (7.87) 290 (.2) 5 (6.06) 2. (53.79) 23.8 (52.7) 50 02. (.03) 230 (9.06) 250 (9.8) 30 (2.20) 6 (6.6) 2 (52.9) 23. (5.59) 300 02. (.03) 255 (0.0) 250 (9.8) 30 (2.20) 6 (6.6) 32 (70.55) 3. (69.23) 600 97.2 (3.83) 275 (0.83) 250 (9.8) 30 (2.20) 6 (6.6) (90.39) 0. (89.07) 6 50 5.2 (6.07) 280 (.02) 300 (.8) 325 (2.80) 7 (6.85) 36.8 (8.3) 36.2 (79.8) 6 300 5.2 (6.07) 320 (2.60) 300 (.8) 325 (2.80) 7 (6.85) 5.8 (.20) 5.2 (2.88) 6 600 6.3 (5.76) 355 (3.98) 300 (.8) 325 (2.80) 7 (6.85) 76.8 (69.3) 6.2 (0.85) 8 50 202.7 (7.98) 35 (3.58) 300 (.8) 350 (3.78) 9 (7.6) 50.6 (.55) 50.0 (0.23) 8 300 202.7 (7.98) 380 (.96) 300 (.8) 350 (3.78) 9 (7.6) 75. (66.23) 7.8 (6.9) 0 50 25.5 (0.02) 05 (5.9) 380 (.96) 370 (.57) 22 (8.82) 75.0 (65.35) 7. (6.02) 0 300 25.5 (0.02) 55 (7.9) 380 (.96) 370 (.57) 22 (8.82) 07.0 (235.89) 06. (23.57) 2 50 30.8 (2.00) 85 (9.09) 50 (7.72) 395 (5.55) 2 (9.6) 06.9 (235.67) 06.3 (23.35) 2 300 30.8 (2.00) 520 (20.7) 50 (7.72) 395 (5.55) 2 (9.6) 5.9 (33.88) 5.3 (333.56) /376 Siemens FI 0 20
Siemens AG 200 a a H Sandwich version, front view, a = 33 mm (5.2 inches) L Sandwich version, front view, a = 33 mm (5.25 inches) c b D H L c b l D d Sandwich version, side view, b = 05 mm (.3 inches), c = 79 mm (7,05 inches) d Sandwich version, side view, b = 05 mm (.3 inches), c = 79 mm (7.05 inches) Siemens FI 0 20 /377
Siemens AG 200 Sandwich version EN Size Pressure rating Dimensions [mm (inches)] Weight [kg (lb)] DN PN d D L H l Flowmeter (with pressure sensor) Flowmeter (without pressure sensor) 5 6... 00 6 (0.63) 5 (.77) 65 (2.56) 265 (0.3) (5.67). (9.0) 3.5 (7.72) 25 6... 00 2 (0.9) 65 (2.56) 65 (2.56) 265 (0.3) (5.67).9 (0.80).3 (9.8) 0 6... 00 38 (.50) 82 (3.23) 65 (2.56) 270 (0.63) (5.67) 5.5 (2.3).9 (0.80) 50 6... 00 50 (.97) 02 (.02) 65 (2.56) 275 (0.83) (5.67) 6.6 (.55) 6 (3.23) 80 6... 00 7 (2.9) 35 (5.3) 65 (2.56) 290 (.2) 55 (6.0) 8.8 (9.0) 8.2 (8.08) 00 6... 00 97 (3.82) 58 (6.22) 65 (2.56) 30 (2.20) 6 (6.6) 0. (22.27) 9.5 (20.9) Sandwich version ASME Size Pressure rating Dimensions [inches] Weight [lb] DN class d D L H l Flowmeter (with pressure sensor) ½" 50, 300, 600 0.63.77 2.56 0.3 5.67 9.0 7.72 " 50, 300, 600 0.9 2.56 2.56 0.3 5.67 0.80 9.8 ½" 50, 300, 600.50 3.23 2.56 0.63 5.67 2.3 0.80 2" 50, 300, 600.97.02 2.56 0.83 5.67.55 3.23 3" 50, 300, 600 2.9 5.3 2.56.2 6.0 9.0 8.08 " 50, 300, 600 3.82 6.22 2.56 2.20 6.6 22.27 20.9 Flowmeter (without pressure sensor) /378 Siemens FI 0 20
Siemens AG 200 Flow tables Measuring Range Limits Size Q min Q max Q min Q max DN to EN 092- DN to ASME B6.5 EN 092- [m 3 /h] EN 092- [m 3 /h] ASME B6.5 [m 3 /h] ASME B6.5 [m 3 /h] Water 5 ½" 0.5 5.07 0..9 25 " 0.8.0 0.8.0 0 ½" 2.0 28.58 2.0 28.58 50 2" 3.53 9.8 3.53 9.8 80 3" 7.7 08.37 7.7 08.37 00 " 3.30 86.22 3.30 86.2 50 6" 30.3 2.86 30.3 2.86 200 8" 56.6 792.2 56.60 792.2 250 0" 90.8 266.8 90.8 266.8 300 2" 3. 839.8 3. 839.8 Values based on water at 20 C (68 F) and.03 bar abs (.7 psi abs ) Size Q min Q max Q min Q max DN to EN 092- DN to ASME B6.5 EN 092- [m 3 /h] EN 092- [m 3 /h] ASME B6.5 [m 3 /h] ASME B6.5 [m 3 /h] Air 5 ½" 6.80 25.33 6.72 2.70 25 " 0.20 8.3 0.20 8.3 0 ½" 25.35 326.63 25.35 326.63 50 2" 3.89 565.9 3.89 565.9 80 3" 96. 238.6 96. 238.60 00 " 65.9 2 28.27 65.9 2 28.27 50 6" 37.23 82.60 37.23 82.60 200 8" 702.95 9 056.8 702.95 9 056.8 250 0" 23.7 78.0 23.7 78.0 300 2" 632. 2 028.0 632. 2 028.0 Values based on air at 20 C (68 F) and.03 bar abs (.7 psi abs ) Flow rate limits Product Nominal diameters Minimum flow rates Maximum flow rates ρ = operating density [kg/m 3 ] to EN to ASME [m/s] [m/s] Liquids DN 5 DN 300 DN ½" DN 2" 0.5 x (998/ρ) 0.5 ) 0.7 ) 7 x (998/ρ) Gas, steam/vapor DN 5 DN 300 DN ½" DN 2" 6 x (.29/ρ) 0.5 2) 7 x (998/ρ) 0.7 3) ) Minimum flow rate 0. m/s (.3 ft/s), maximum flow rate 0 m/s (32.8 ft/s) 2) Minimum flow rate 2 m/s (6.6 ft/s), maximum flow rate 80 m/s (262 ft/s) 3) Minimum flow rate 2 m/s (6.6 ft/s), maximum flow rate 80 m/s (262 ft/s); DN 5: 5 m/s (8 ft/s) and DN 25: 70 m/s (230 ft/s) Siemens FI 0 20 /379
Siemens AG 200 Measuring range saturated steam: to 7 bar Overpressure [bar] 3.5 5.2 7 Density [kg/m³].398 2.258 3.27653.6732 Temperature [ C] 20.6 8.2 60. 70.6 Flow [kg/h] min. max. min. max. min. max. min. max. DN to EN 092- DN to ASME B6.5 5 ½" 5.87 28.75 7.68 6.6 8.93 83.0 0.06 05.57 25 ".82 92.2 7.28 97.53 20.09 266.8 22.66 339.35 0 ½" 29.6 370.7 3.33 792.33 50.63 070.2 56.8 36.2 50 2" 5.3 6.82 75.02 37.8 87.9 852.8 98.33 2 356.6 80 3" 2. 05.8 6.33 3 00.7 9 058. 25.39 5 6.8 00 " 93. 2 5.5 282.36 5 62.7 328.6 6 973.3 370.09 8 869.2 50 6" 37.56 5 72. 639.69 696 73.5 5 798 838. 20 093 200 8" 82.9 0 279.0 20.6 2 970.0 396.5 29 675.0 57.9 37 73 250 0" 33.9 6 33.0 920.9 35 22.0 2 232.5 7 39.0 2 57.7 60 337 300 2" 908.3 23 866.0 2 789.8 5 00.0 3 22. 68 899.0 3 656.6 87 630 Measuring range saturated steam: 0.5 to 20 bar Overpressure [bar] 0.5 7.5 20 Density [kg/m³] 5.88803 7.60297 9.3702 0.52 Temperature [ C] 86.2 98.5 208.7 25 Flow [kg/h] min. max. min. max. min. max. min. max. DN to EN 092- DN to ASME B6.5 5 ½" 2.78 9.7 6.5 92.6 20.23 236.0 22.89 267.2 25 " 26.93 79.6 30.6 69. 33.87 758.69 36.0 858.62 0 ½" 67.5 878.2 76.72 2 50.7 8.93 2 395.3 90.35 2 557.7 50 2" 6.89 3 25.7 32.82 3 723. 7.03 7 56.2 28. 80 3" 256.03 7 22. 290.93 8 55.8 322.06 9 083.7 32.62 9 699.3 00 " 39.9 2 238 99.9 03 553.38 5 608 588.69 6 666 50 6" 996.62 27 725 32.5 3 77 253.7 35 359 333.7 37 756 200 8" 872. 52 079 2 27.3 59 63 2 35.9 66 9 2 505.2 70 92 250 0" 2 992.7 83 25 3 00.7 95 333 3 76.6 06 80 00.9 3 380 300 2" 36.5 20 920 939. 38 60 5 67.5 5 20 5 86.5 6 660 /380 Siemens FI 0 20
Siemens AG 200 Measuring range saturated steam: 5 to 00 psig Overpressure [psig] 5 50 75 00 Density [lbs/ft³] 0.079 0.97 0.2036 0.2569 Temperature [ F] 29.98 297.86 320.36 338.8 Flow [lbs/h] min. max. min. max. min. max. min. max. DN to EN 092- DN to ASME B6.5 5 ½" 2.95 6.35 6.83 33.87 9.62 82.02 22.0 229.63 25 " 26.25 206.83 37.86 30.3.5 585.06 9.59 738.09 0 ½" 65.8 829.6 9.92 726 0.68 2 36.7 2.32 2 960.5 50 2" 3.9 36.3 6.3 2 988 9.63 062.9 25.23 5 25.6 80 3" 29.57 3 6. 360 6 55.3 9.7 8 899. 7.5 227 00 " 28.8 5 05.7 68.5 26 72.2 5 29 80.06 9 29 50 6" 97.7 2 26 0.2 25 78 633.9 3 62 835.2 3 703 200 8" 82.8 23 00 2 632. 7 859 3 069. 65 072 3 7.2 82 092 250 0" 2 97.2 36 77 207.7 76 508 906. 0 030 5 50.8 3 230 300 2" 236.8 53 0 6. 20 7 25.8 5 080 8 003.6 90 600 Measuring range saturated steam: 50 to 300 psig Overpressure [psig] 50 200 250 300 Density [lbs/ft³] 0.3627 0.68 0.5735 0.6792 Temperature [ F] 366.08 388.0 06.22 22.06 Flow [lbs/h] min. max. min. max. min. max. min. max. DN to EN 092- DN to ASME B6.5 5 ½" 27.79 32.2 35.86 8.7 3.9 52.66 52.0 607.2 25 " 58.93 02. 66.9 35. 7. 67.8 80.63 95.5 0 ½" 7.72 07.2 67.83 702.8 85.76 5 237 202.5 5 728 50 2" 255.75 7.9 290.56 8.9 32.6 9 066.8 350 9 97 80 3" 560.9 5 578 636. 7 83 70.3 9 860 766.6 2 722 00 " 962.5 26 766 093.5 30 63 20. 3 2 37.2 37 32 50 6" 2 80.6 60 639 2 77. 69 2 2 72. 77 307 2 98 8 556 200 8" 096. 3 900 653.6 30 00 5 50.7 5 20 5 605.2 58 830 250 0" 6 58. 82 090 7 39.3 208 60 8 23. 232 0 8 960.6 253 90 300 2" 9 50.2 26 60 0 805 302 760 959 337 50 3 0 368 770 Siemens FI 0 20 /38