MK IV HORIZONTAL SLIDING DOOR REPLACEMENT PARTS BOOK BI-PARTING DOOR SHOWN-SINGLE DOOR SIMILAR JAMISON DOOR COMPANY P.O. BOX 70 HAGERSTOWN, MARYLAND 21740 1-800-532-3667 301-733-3100 INTERNET: http://www.jamisondoor.com E-MAIL: contact@jamisondoor.com ECN CS-2169 AFTER INSTALLING THE DOOR PLEASE FORWARD TO JAMISON DOOR COMPANY THE MAINTENANCE DEPARTMENT OR OWNER. P/N 996543
THIS PAGE LEFT BLANK ECN CS-2169 2
CONTENTS SECTION TITLE PAGE 1. Instruction Sheet for Ordering Replacement Parts 4 2. General Information 6 3. Steel Track, Track Assembly 7 4. Plastic Track, Track Assembly 8 5. Carrier Assembly 9 6. Chain Lock 10 7. Stay Roller 12 8. Heavy Duty Stay Roller 13 9. Stay Bracket 14 10. Idler 15 11. Power Unit 16 12. Control Panel (for Control Panels Shipped Prior to 1/1/06) 18 13. Control Panel Standard Speed (for Control Panels Shipped After 1/1/06) 20 14. Control Panel Standard Speed 575 V (for Control Panels Shipped After 1/1/06) 22 15. Control Panel Dual Speed (for Control Panels Shipped After 1/1/06) 24 16. Control Panel Dual Speed 575 V (for Control Panels Shipped After 1/1/06) 26 17. Limit Switch Assembly 28 18. DMC Assembly 30 19. Control Panel Box, DMC 31 20. DMC Control Panel Assembly 32 21. Control Panel Components Continued, DMC 34 22. Control Panel Components Continued, DMC 575 V 36 23. JamECO Control Box 37 24. Pull Cord Switch 39 25. Manual Disconnect 40 26. Front Padlocking Hardware 42 27. Pneumatic Reversing Edge 44 28. Miscellaneous Door Parts 46 29. Gasket Assembly 48 30. Optional Pull Bar Handle (Single Manual Door Only) 50 ECN CS-2169 3
NOTES: 1. INSTRUCTION SHEET FOR ORDERING REPLACEMENT PARTS 1. Sufficient information must be included with all orders so that we can give prompt and accurate service. The specific information needed includes: a. The stock number, drawing number and name of the part I. If possible give the stock number or drawing number of the part to be replaced. b. The HIC and WIC of the door. c. State whether the door is a bi-parting or single. If the door is a single state which direction it opens. d. Finish I. Galvanized (Galv), chrome (Chr), bright chrome (BChr), stainless steel (SST), or Tuffkote finish (similar to gray paint). Other coatings may be available see the applicable parts lists for information. 2. Parts highlighted in gray are no longer available. ECN CS-2169 4
DETAIL A ECN CS-2169 5
2. GENERAL INFORMATION ECN CS-2169 6
3. STEEL TRACK, TRACK ASSEMBLY Ref # Group Finish Offset Name of Part Stock No. Drawing No. 1 Track Support Angle Single Door LH 5 0 WIC 4404-204-02 4404-204 1 Track Support Angle Single Door RH 5 0 WIC 4404-204-52 4404-204 1 Track Support Angle Single Door LH 6 0 WIC 4404-204-03 4404-204 1 Track Support Angle Single Door RH 6 0 WIC 4404-204-53 4404-204 1 Track Support Angle Bi-Parting Door 6 0 WIC 4404-205-03 4404-205 1 Track Support Angle Single Door LH 7 0 WIC 4404-204-04 4404-204 1 Track Support Angle Single Door RH 7 0 WIC 4404-204-54 4404-204 1 Track Support Angle Bi-Parting Door 7 0 WIC 4404-205-04 4404-205 1 Track Support Angle Single Door LH 8 0 WIC 4404-204-05 4404-204 1 Track Support Angle Single Door RH 8 0 WIC 4404-204-55 4404-204 1 Track Support Angle Bi-Parting Door 8 0 WIC 4404-205-05 4404-205 1 Track Support Angle Single Door LH 10 0 WIC 4404-204-07 4404-204 1 Track Support Angle Single Door RH 10 0 WIC 4404-204-57 4404-204 1 Track Support Angle Bi-Parting Door 10 0 WIC 4404-205-07 4404-205 2 Flat Washer 13/16 x 13/32 x 13 GA 753-006 3 Bolt 3/8-16 x 1-3/4 751-423 4 Track Stop Bumper 4404-287-01 4404-287 5 Screw Thread Form #10-24 x 1/2" 765-213 Note: See instruction sheet for ordering parts. Note if the track is one or two piece construction. ECN CS-2169 7
4. PLASTIC TRACK, TRACK ASSEMBLY Ref # Group Finish Offset Name of Part Stock No. Drawing No. 1 Track Support Angle 5 0 WIC 4404-397-03 4404-397 1 Track Support Angle 5 6 WIC 4404-397-04 4404-397 1 Track Support Angle 6 0 WIC 4404-397-05 4404-397 1 Track Support Angle 7 0 WIC 4404-397-07 4404-397 1 Track Support Angle 8 0 WIC 4404-397-09 4404-397 1 Track Support Angle 9 0 WIC 4404-397-11 4404-397 1 Track Support Angle 10 0 WIC 4404-397-13 4404-397 2 Galv Hex Head Washer Screw 769-102 3 Track Stop Bumpers 4404-287-01 4404-287 4 Leading Edge Plastic Standard Ramp LH 931-024 4404-400 4** Leading Edge Plastic Short Ramp LH 931-054 4404-894 4 Leading Edge Plastic Standard Ramp RH 931-022 4404-398 4** Leading Edge Plastic Short Ramp RH 931-052 4404-892 5* Intermediate Track Piece #6 (Specify Length) (Single) XXX-XXX 5* Intermediate Track Piece #6 (Specify Length) (Bi-parting) XXX-XXX 6 Trailing Edge Plastic Standard Ramp LH 931-025 4404-401 6** Trailing Edge Plastic Short Ramp LH 931-055 4404-895 6 Trailing Edge Plastic Standard Ramp RH 931-023 4404-399 6** Trailing Edge Plastic Short Ramp RH 931-053 4404-893 7* Tail Track Piece #7 (Specify Length) (Single) XXX-XXX 7* Tail Track Piece #7 (Specify Length) (Bi-parting) XXX-XXX 8 Track Stop 486-153 4404-402 9 Screw Self Tap 3/8-16 x 1-1/2 765-405 10 Screw Thread form #10-24 x 1/2 765-213 11 Nut Nylock 3/8-16 752-205 12 Under Track Stop 4404-937-01 4404-937 13 Bolt Machine Hex Head 751425 14 Washer 13 ga. X 13/16 OD X 13/32 ID 753-006 *Please specify the serial number of the door when ordering. ** Short Ramps are only to be used with pull bar. Note: See instruction sheet for ordering parts. ECN CS-2169 8
5. CARRIER ASSEMBLY Ref # Group Finish Offset Name of Part Stock No. Drawing No. 1 a Bolt 3/4-10 X 6 751-468 2 a Hanger Bracket (4 & 6 Door) 4404-007-01 4404-7 2A a Hanger Bracket (2 Door) 4404-541-01 4404-541 3 a Roll Pin 3/16 Dia. X 1 754-022 4 a Hex Nut 3/4 10 752-113 S.Assy. Hanger Sub-Assy. (Consist of Items in Group (a)) 4404-021-01 4404-21 5 Galv Trolley Wheel Leading Edge 486-055 5 SST Trolley Wheel Leading Edge 486-060 5 Trolley Wheel Leading Edge (Heat Treated for Steel Track) 486-090 6 Galv Trolley Wheel Trailing Edge 486-050 6 SST Trolley Wheel Trailing Edge 486-061 6 Trolley Wheel Trailing Edge (Heat Treated for Steel Track) 486-091 7* Self Tapping Screw #10-24 X 3/8 (MK III Steel Track Only) 765-309 8* Track Cleaner (MK III Steel Track Only) 4404-093-01 4404-93 9 Hex Jam Nut 3/4 10 752-115 10 Ext. Tooth Lock Washer 3/4 753-550 11 Hex Bolt Self Tapping 3/8-16 X 1 769-102 12 Spring Lock Washer 1/2 753-505 13 Hex Bolt 1/2 13 X 1 751-438 14 Carrier Single 5 0 4404-008-01 4404-8 14 Carrier Single 6 0 4404-008-02 4404-8 14 Carrier Bi-Parting 6 0 4404-008-31 4404-8 14 Carrier Single 7 0 4404-008-03 4404-8 14 Carrier Bi-Parting 7 0 4404-008-32 4404-8 14 Carrier Single 8 0 4404-008-04 4404-8 14 Carrier Bi-Parting 8 0 4404-008-33 4404-8 14 Carrier Single 10 0 4404-008-06 4404-8 14 Carrier Bi-Parting 10 0 4404-008-35 4404-8 15 Trolley Wheel Spacer 486-048 * Specify Door Thickness Note: See instruction sheet for ordering parts. Specify whether the door is single or bi-parting and give the WIC. ECN CS-2169 9
6. CHAIN LOCK ECN CS-2169 10
Ref # Group Finish Offset Name of Part Stock No. Drawing No. 1B Galv Chain Lock Assy. LH 4404-050-03 4404-50 1A Galv Chain Lock Assy. RH 4404-049-01 4404-49 1B SST Chain Lock Assy. LH, (Items 1, 3 and 4 are Galv) 4404-050-02 4404-50 1A SST Chain Lock Assy. RH, (Items 1, 3 and 4 are Galv) 4404-049-02 4404-49 1 Galv Guide Block 486-134 2 Base 4404-046-01 4404-46 3 Galv Plunger 486-135 4 Galv Guide Plate 4404-290-01 4404-290 5 Extension Bracket (RH Only) 4404-045-01 4404-45 6 Hex Nut 3/8 16 752-205 7 Set Screw 1/4 20 X 5/8 767-119 8 Spring 482-029 9 Galv Bushing Plate (Which includes Bushing No. 16) 4404-186-01 4404-186 9 SST Bushing Plate (Which includes Bushing No. 16) 4404-186-02 4404-186 10 Hex Bolt 3/8-16 X1 769-102 11 Hex Bolt 3/8-16 X2 751-424 12 Drive Link 4404-013-01 4404-13 13 Connecting Link 2040 1 Pitch 202-011 14 Offset Link 2040 1 Pitch 202-012 15 Drive Chain 2040 1 Pitch 202-010 16 Bushing 191-163 17 Extension Bracket Tapping Plate 4404-302-01 4404-302 Note: See instruction sheet for ordering parts. ECN CS-2169 11
7. STAY ROLLER 2 8 Ref # Group Finish Offset Name of Part Stock No. Drawing No. Assy. SST Complete Stay Roller Assy. (For Use When Stay Roller is Located in Freezer) 4404-732-01 4404-732 Assy. SST Complete Stay Roller Assy. Standard 4404-019-02 4404-19 1 Hex Bolt 3/8 16 x 2-1/2 751-514 2 Flat Washer 1-1/16 x 33/64 x 13 GA (Freezer) 753-155 3 Wheel Only (Cooler) 486-051 3 Wheel Only (Freezer) 486-062 4 Flat Washer 13/16 x 13/32 x 13 GA 753-169 5 SST Stay Roller Bracket 4404-017-02 4404-17 6 Hex Lock Nut 3/8 16 752-205 7* Anchor Bolt 1/2 x 3-3/4 759-022 8 Spindle 486-063 *Item is not included in assembly. Note: See instruction sheet for ordering parts. ECN CS-2169 12
8. HEAVY DUTY STAY ROLLER Ref # Group Finish Offset Name of Part Stock No. Drawing No. Assy. Galv Heavy Duty Stay Roller 4404-694-01 4404-694 Assy. SST Heavy Duty Stay Roller 4404-694-02 4404-694 1 Galv Bracket 4404-696-01 4404-696 1 SST Bracket 4404-696-02 4404-696 2 Galv Mounting Plate 4404-695-01 4404-695 2 SST Mounting Plate 4404-695-02 4404-695 3 SST Flat Washer 13/16 x 13/32 x 13 GA 753-169 4 SST Hex Head Mach Bolt 3/8-16 x 2-1/2 751-514 5 Hex Head Mach Bolt 3/8-16 x 1-1/4 (Zn Plated) 751-421 6 Hex Nut Nylock 3/8-16 (Zn Plated) 752-205 7 SST Bushing Tube 486-063 8 Polyolefin Wheel 486-051 Note: See instruction sheet for ordering parts. ECN CS-2169 13
9. STAY BRACKET Ref # Group Finish Offset Name of Part Stock No. Drawing No. Assy Stay Wedge Assy Painted Yellow (For 4 Thick Door) 4404-923-01 4404-923 Assy SST Stay Wedge Assy. (For 4 Thick Door) 4404-923-02 4404-923 Assy Stay Wedge Assy Painted Yellow (For 6 Thick Door) 4404-923-21 4404-923 Assy SST Stay Wedge Assy (For 6 Thick Door) 4404-923-22 4404-923 *Kit Stay Wedge Assy Painted Yellow (For 4 Thick Door) Retrofit Kit (Floor Mount Only) 4404-923-31 4404-923 *Kit SST Stay Wedge Assy (For 4 Thick Door) *Kit Retrofit Kit (Floor Mount Only) 4404-923-32 4404-923 Stay Wedge Assy Painted Yellow (For 6 Thick Door) Retrofit Kit (Floor Mount Only) 4404-923-33 4404-923 *Kit SST Stay Wedge Assy (For 6 Thick Door) Retrofit Kit (Floor Mount Only) 4404-923-34 4404-923 *1 Hex Head Machine Screw 1/4-20 x 1-1/2 751-405 2 Flat Washer 9/16 x ¼ x 18 Ga 753-001 *3 Flat Washer 5/8 x 9/32 x 16 GA 753-002 4 SST Lock Washer Split 1/4 753-503 *5 Expansion Shield 759-031 6 Round HD Mach Screw ¼ -20 x ¾ 764-601 **7 Hex Taptite 3/8-16 x 1 769-102 8 Wedge Assembly 4404-939-01 4466-080 9 Bracket Painted Yellow (For 4 Thick Door) 4404-924-01 4404-924 9 SST Bracket (For 4 Thick Door) 4404-924-02 4404-924 9 Bracket Painted Yellow (For 6 Thick Door) 4404-924-21 4404-924 9 SST Bracket (For 6 Thick Door) 4404-924-22 4404-924 *Used for retrofits (items 1,3 & 5 are used to fasten floor wedge to floor) **Used for non-retrofits Note: See instruction sheet for ordering parts. When retrofitting a bi-parting door with stay brackets a RH and LH kit should be ordered. ECN CS-2169 14
10. IDLER Ref # Group Finish Offset Name of Part Stock No. Drawing No. Assy. Complete Idler Assy. 4404-033-01 4404-33 1 Sprocket Bracket 4404-036-01 4404-36 2 Sprocket Mounting Bracket 4404-031-01 4404-31 3 Idler Adjustment Bracket 4404-030-01 4404-30 4 Idler Bearing 481-016 5 Idler Sprocket 203-019 6 Idler Spring 559-101 7 Spacer 4287-033-01 4404-33 8 Plate 4404-228-01 4404-228 9 Carriage Bolt 1/2-13 x4 751-030 10 Hex Lock Nut 3/8 16 752-205 11 Hex Bolt 3/8-16 x 1-1/4 751-421 12 Hex Lock Nut 1/2 13 752-207 13 Hex Bolt 3/8-16 x 1 751-420 14 Hex Bolt 3/8 16 x 1 Taptite 769-102 15 Flat Washer 1-3/4 x 13/32 x 1/8 753-022 16 Flat Washer 1-3/8 x 9/16 x 20 GA 753-019 17 Split Lock Washer 3/8 753-504 18 Hex Bolt 3/8 16 x 1-1/2 751-422 Note: See instruction sheet for ordering parts. ECN CS-2169 15
11. POWER UNIT ECN CS-2169 16
Ref # Group Finish Offset Name of Part Stock No. Drawing No. Assy. Complete Power Unit Assy. (Specify Power Requirements and Give Model and Serial Numbers) 4404-43X-XX 4404-43X 1A Gear Box Sub-Assy. (Standard Powertron) 201-101 1B Gear Box Sub-Assy. (Dual Speed) 201-104 2 Limit Switch Drive Sprocket (Standard Speed) 203-027 2 Limit Switch Drive Sprocket (Dual Speed) 203-041 3A Drive Sprocket (Standard Speed and Reduced Dual Speed) 203-040 3B Drive Sprocket (Dual Speed) 203-041 4* Bearing Bracket 4404-038-01 4404-38 4A* a Bearing Bracket, Current Design 4404-435-01 4404-435 5* Bearing 481-065 5A* a Bearing, Current Design 481-101 Assy. Bearing Bracket Assy. (Consists of Items in Group (a)) (The Current Design is a Direct Replacement for Older Designs) 4404-039-01 4404-39 6B a Bolt (For Mounting the Bearing Bracket) (Not Shown) 751-008 6C a Washer (For Mounting the Bearing Bracket) (Not Shown) 753-003 6D a Nut (For Mounting the Bearing Bracket) (Not Shown) 752-204 7 Mounting Plate 4395-028-01 4395-28 8 Motor (1/2 HP 120 VAC) 133-308 8 Motor (1/4 HP 208-240-48- VAC) 133-311 8 Motor (1/2 HP 208-240-480 VAC) (Soft Start) 133-306 8 Motor Dual Speed (208-240 VAC) 133-309 8 Motor Dual Speed (480 VAC) 133-310 8 Motor (1/4 HP 575 VAC) 133-320 8 Motor Dual Speed (575 VAC) 133-321 8 Motor (1/2 HP 575 VAC) (Soft Start) 133-319 9 Clip Angle 4395-027-01 4395-27 10 Rubber Grommet 559-029 11* Limit Switch Assy. (See Limit Switch Assy.) 4395-026-XX 4395-26 12* Control Panel Assy. (See Control Panel Assy.) 13 Hex Nut 3/8 16 752-205 14 Hex Nut 1/4-20 752-203 15 Flat Washer 5/8 X 9/32 X 16 GA 753-002 16 Rubber Washer 11/16 X 9/32 X 1/16 559-026 17 Hex Bolt 1/4 20 X 3/4 751-402 18 Flat Washer 1-1/4 X 9/32 X 16 GA 753-015 19 Flat Washer 13/16 X 13/32 X 16 GA 753-006 20 Hex Bolt 3/8-16 X 2 751-424 21 Limit Switch Chain 20-1/2 Long 4395-040-11 4395-40 22 Key 1/4 x 1/4 x1 315-001 23 Key 1/8 Square X 1 Long 4290-120-01 4290-120 24 Split Lock Washer 3/8 753-503 25 Hex Bolt 3/8-16 X 7/8 751-420 26 Hex Bolt 3/8 16 X 1-1/2 751-422 27 Mounting Bracket 4404-037-01 4404-37 28 Connecting Link 202-005 29 Offset Link (Not Shown) 202-006 Note: See instruction sheet for ordering parts. ECN CS-2169 17
12. CONTROL PANEL (FOR CONTROL PANELS SHIPPED PRIOR TO 1/1/2006) Ref # Group Finish Offset Name of Part Stock No. Drawing No. Assy. Complete Control Panel Assy. (Give Model Number & Serial Numbers) (Specify NEMA 1, 3, 4, 4X or 12) 4390-238-XX 4390-238 *1 Housing NEMA 3, 4 or 12 191-037 1 Housing NEMA 1 486-117 1 Housing NEMA 4X 191-040 2 Mounting Plate 4390-237-01 4390-237 3 Baffle 4390-122-01 4390-122 4 Transformer (240/480 Primary 24 Volt Secondary) 115-106 5 Transformer (120/208/380 Primary 24 Volt Secondary) 115-107 6 Fuse FNM-2 116-103 7 Reversing Contactor 111-037 8 Brass Cup Washer 753-905 9 Marker Strip 191-508 10 Terminal Strip 191-505 11 Stop Switch 113-108 12 Relay 111-029 13 Pilot Light (120V or 240V) 4290-073-01 4290-73 13 Pilot Light with Resister (480V) 4290-073-03 4290-73 14 Time Delay 111-227 15 Termostst (80 ) Optional 114-005 16 Heater (20 Watt) Optional 4369-044-01 4369-44 *17 Rubber Washer 11/16 X 9/32 X 1/16 559-026 18 Self Tapping Screw #6-32 X 3/8 765-303 19 Self Tapping Screw #6-32 X 1/2 765-304 20 Self Tapping Screw #6-32 X 5/8 765-305 21 Self Tapping Screw #8-32 X 3/8 765-306 22 Round Head Machine Screw #10-32 X 3/8 764-136 23 Self Tapping Screw #10-24 X 1/2 765-310 24 Dual Speed Adder Block 111-040 Note: See instruction sheet for ordering parts. ECN CS-2169 18
THIS PAGE LEFT BLANK ECN CS-2169 19
13. CONTROL PANEL POWERTRON STANDARD SPEED (FOR CONTROL PANELS SHIPPED AFTER 1/1/06) ECN CS-2169 20
Ref # Group Finish Offset Name of Part Stock No. Drawing 1 DPDT Relay 111-029 4290-963 2 Rev. Contactor 60 Hz. 111-037 3 4 Floor Loop Socket 11-Pins, Octal Style 111-049 5 Time Delay 111-227 4390-216 6 Switch, Stop 113-108 4390-138 7 Thermostat 114-005 4290-69 8 Transformer Class 2 115-009 4390-434 9 Fuse 3AG, 1/4 Amp 116-107 10 Fuse, 3 Amp FNQ-R-3 600 VAC 116-108 11 Counter ENM #E4B74D 119-013 12 Floor Loop Unit 326SF24A-7, Harness 802A-4 119-014 13 Radio Control Multi-Code 1090 119-015 14 End Stop 170-004 15 Fuse Block 2 Poles 191-166 16 Fuse Block 1 Pole 191-167 17 Grounding Lug 191-355 18 Terminal Blocks 2-142 191-501 19 Marker, Number 191-508 4390-231 20 Enclosure, NEMA 4 191-514 4395-197 21 Enclosure, NEMA 4x 191-515 4395-197 22 Terminal Block 8 Rowes 191-518 23 24 25 Enclosure, NEMA 1 486-204 4390-416 26 Base Plate #16 GA. x 11 x 11 486-205 4390-423 27 Din Rail 35mm x 5.25 4390-406-02 4390-406 28 Bracket, Fuse Block #16 GA. 4390-417-01 4390-417 29 Baffle Plate #16 GA. 4390-418-01 4390-418 30 Bracket #16 GA. 4390-420-01 4390-420 31 Retainer #16 GA. 4390-422-01 4390-422 32 Heater Assy. 50W.120V. 4390-426-01 4390-426 33 Pilot Light Assy. NEMA 1 120V / 240V 4390-432-01 4390-432 34 Pilot Light Assy. NEMA 1 480V 4390-432-02 4390-432 35 Pilot Light Assy. NEMA 4 480V (STD) 4390-433-01 4390-433 36 Pilot Light Assy. NEMA 4 240V 199-016 37 Grounding Wire, Control Panel 14 AWG 13 Lg. 4390-470-02 4390-470 Note: See instruction sheet for ordering parts. COMPLETE CONTROL PANEL ASSEMBLY (ACTIVE MODEL NUMBERS) (ALSO SPECIFY NEMA 1, 4, OR 4X) STANDARD SPEED 4390-436-XX OPTIONAL KITS AVAILABLE CONTROL PANEL HEAT.. H4390-444 FLOOR LOOP.. H4390-425 RADIO CONTROL H4390-424 TIME DELAY.. H4390-227 ECN CS-2169 21
14. CONTROL PANEL POWERTRON STANDARD SPEED 575 V (FOR CONTROL PANELS SHIPPED AFTER 1/1/06) ECN CS-2169 22
Ref # Group Finish Offset Name of Part Stock No. Drawing 1 DPDT Relay 111-029 4290-963 2 Rev. Contactor 60 Hz. 111-037 3 4 Floor Loop Socket 11-Pins, Octal Style 111-049 5 Time Delay 111-227 4390-216 6 Switch, Stop 113-108 4390-138 7 Thermostat 114-005 4290-69 8 Transformer 575 Volts 115-113 9 Fuse 3AG, 1/4 Amp 116-107 10 Fuse, 3 Amp FNQ-R-3 600 VAC 116-108 11 Counter ENM #E4B74D 119-013 12 Floor Loop Unit 326SF24A-7, Harness 802A-4 119-014 13 Radio Control Multi-Code 1090 119-015 14 End Stop 170-004 15 Fuse Block 2 Poles 191-166 16 Fuse Block 1 Pole 191-167 17 Grounding Lug 191-355 18 Terminal Blocks 2-142 191-501 19 Marker, Number 191-508 4390-231 20 Enclosure, NEMA 4 191-514 4395-197 21 Enclosure, NEMA 4x 191-515 4395-197 22 Terminal Block 8 Rowes 191-518 23 24 25 Enclosure, NEMA 1 486-204 4390-416 26 Base Plate #16 GA. x 11 x 11 486-205 4390-423 27 Din Rail 35mm x 5.25 4390-406-02 4390-406 28 Bracket, Fuse Block #16 GA. 4390-417-01 4390-417 29 Baffle Plate #16 GA. 4390-418-01 4390-418 30 Bracket #16 GA. 4390-420-01 4390-420 31 Retainer #16 GA. 4390-422-01 4390-422 32 Heater Assy. 50W.120V. 4390-426-01 4390-426 33 34 Pilot Light Assy. NEMA 1 480V 4390-432-02 4390-432 35 Pilot Light Assy. NEMA 4 575V (STD) 4390-433-03 4390-433 36 Grounding Wire, Control Panel 14 AWG 13 Lg 4390-470-02 4390-470 37 Fuse Holder Din Rail Mtg. 170-020 38 Fuse FNM-3 3 Amp 116-105 Note: See instruction sheet for ordering parts. COMPLETE CONTROL PANEL ASSEMBLY (ACTIVE MODEL NUMBERS) (ALSO SPECIFY NEMA 1, 4, OR 4X) STANDARD SPEED 575 VOLT 4390-457-XX OPTIONAL KITS AVAILABLE CONTROL PANEL HEAT.. H4390-444 FLOOR LOOP.. H4390-425 RADIO CONTROL H4390-424 TIME DELAY.. H4390-227 ECN CS-2169 23
15. CONTROL PANEL POWERTRON DUAL SPEED (FOR CONTROL PANELS SHIPPED AFTER 1/1/06) ECN CS-2169 24
Ref # Group Finish Offset Name of Part Stock No. Drawing 1 DPDT Relay 111-029 4290-963 2 Rev. Contactor 60 Hz. 111-037 3 Aux. Contact Adder Deck A-B #100-FA40 (Dual Speed) 111-040 4 Floor Loop Socket 11-Pins, Octal Style 111-049 5 Time Delay 111-227 4390-216 6 Switch, Stop 113-108 4390-138 7 Thermostat 114-005 4290-69 8 Transformer Class 2 115-009 4390-434 9 Fuse 3AG, 1/4 Amp 116-107 10 Fuse, 3 Amp FNQ-R-3 600 VAC 116-108 11 Counter ENM #E4B74D 119-013 12 Floor Loop Unit 326SF24A-7, Harness 802A-4 119-014 13 Radio Control Multi-Code 1090 119-015 14 End Stop 170-004 15 Fuse Block 2 Poles 191-166 16 Fuse Block 1 Pole 191-167 17 Grounding Lug 191-355 18 Terminal Blocks 2-142 191-501 19 Marker, Number 191-508 4390-231 20 Enclosure, NEMA 4 191-514 4395-197 21 Enclosure, NEMA 4x 191-515 4395-197 22 Terminal Block 8 Rowes 191-518 23 24 25 Enclosure, NEMA 1 486-204 4390-416 26 Base Plate #16 GA. x 11 x 11 486-205 4390-423 27 Din Rail 35mm x 5.25 4390-406-02 4390-406 28 Bracket, Fuse Block #16 GA. 4390-417-01 4390-417 29 Baffle Plate #16 GA. 4390-418-01 4390-418 30 Bracket #16 GA. 4390-420-01 4390-420 31 Retainer #16 GA. 4390-422-01 4390-422 32 Heater Assy. 50W.120V. 4390-426-01 4390-426 33 Pilot Light Assy. NEMA 1 240V 4390-432-01 4390-432 34 Pilot Light Assy. NEMA 1 460 4390-432-02 4390-432 35 Pilot Light Assy. NEMA 4 240V 199-016 36 Pilot Light Assy. NEMA 4 460V 4390-433-02 4390-433 37 Grounding Wire, 14 AWG 13 lg. 4390-470-02 4390-470 Note: See instruction sheet for ordering parts. COMPLETE CONTROL PANEL ASSEMBLY (ACTIVE MODEL NUMBER) (ALSO SPECIFY NEMA 1, 4, OR 4X) DAUL SPEED.. 4390-440-XX OPTIONAL KITS AVAILABLE CONTROL PANEL HEAT.. H4390-444 FLOOR LOOP.. H4390-425 RADIO CONTROL H4390-424 TIME DELAY.. H4390-227 ECN CS-2169 25
16. CONTROL PANEL POWERTRON DUAL SPEED 575 V (FOR CONTROL PANELS SHIPPED AFTER 1/1/06) ECN CS-2169 26
Ref # Group Finish Offset Name of Part Stock No. Drawing 1 DPDT Relay 111-029 4290-963 2 Rev. Contactor 60 Hz. 111-037 3 Aux. Contact Adder Deck A-B #100-FA40 (Dual Speed) 111-040 4 Floor Loop Socket 11-Pins, Octal Style 111-049 5 Time Delay 111-227 4390-216 6 Switch, Stop 113-108 4390-138 7 Thermostat 114-005 4290-69 8 Transformer 575 Volts 115-113 9 Fuse 3AG, 1/4 Amp 116-107 10 Fuse, 3 Amp FNQ-R-3 600 VAC 116-108 11 Counter ENM #E4B74D 119-013 12 Floor Loop Unit 326SF24A-7,Harness 802A-4 119-014 13 Radio Control Multi-Code 1090 119-015 14 End Stop 170-004 15 Fuse Block 2 Poles 191-166 16 Fuse Block 1 Pole 191-167 17 Grounding Lug 191-355 18 Terminal Blocks 2-142 191-501 19 Marker, Number 191-508 4390-231 20 Enclosure, NEMA 4 191-514 4395-197 21 Enclosure, NEMA 4x 191-515 4395-197 22 Terminal Block 8 Rows 191-518 23 24 25 Enclosure, NEMA 1 486-204 4390-416 26 Base Plate #16 GA. x 11 x 11 486-205 4390-423 27 Din Rail 35mm x 5.25 4390-406-02 4390-406 28 Bracket, Fuse Block #16 GA. 4390-417-01 4390-417 29 Baffle Plate #16 GA. 4390-418-01 4390-418 30 Bracket #16 GA. 4390-420-01 4390-420 31 Retainer #16 GA. 4390-422-01 4390-422 32 Heater Assy. 50W.120V. 4390-426-01 4390-426 33 34 Pilot Light Assy. NEMA 1 575V (DS) 4390-432-02 4390-432 35 36 Pilot Light Assy. NEMA 4 575V (DS) 4390-433-04 4390-433 37 Fuse Holder Din Rail Mtg. 170-020 38 Fuse FNM-3 3 Amp 116-105 39 Grounding Wire, Control Panel 4390-470-02 4390-470 Note: See instruction sheet for ordering parts. COMPLETE CONTROL PANEL ASSEMBLY (GIVE MODEL NUMBER & SERIAL NUMBERS) (ALSO SPECIFY NEMA 1, 4, OR 4x) -DUAL SPEED 575 V...4390-458-xx OPTIONAL KITS AVAILABLE -CONTROL PANEL HEAT.H4390-444 -FLOOR LOOP.H4390-425 -RADIO CONTROL..H4390-424 -TIME DELAY....H4390-227 ECN CS-2169 27
17. LIMIT SWITCH ASSEMBLY ECN CS-2169 28
Ref # Group Finish Offset Name of Part Stock No. Drawing Assy. Complete Limit Switch Assy. (Dual Speed) (NEMA1) 4395-026-04 4395-26 Assy. Complete Limit Switch Assy. (Dual Speed) (NEMA 4) 4395-026-05 4395-26 1 Housing (NEMA 4) 4395-199-01 4395-199 1 Housing (NEMA 1) 486-118 1 Housing (NEMA 4x) 4395-199-02 4395-199 2 Label 995-423 3 Base 4395-012-01 4395-12 4 Limit Switch Mounting Block 934-003 5A Actuator Block (Standard) 934-004 5B Actuator Block (Dual Speed) 934-014 6 Flange Bearing 481-018 7 Pillow Block Bearing 481-250 8A Shaft (Standard) 486-133 8B Shaft (Dual Speed) 486-157 9 Sprocket 4395-018-01 4395-18 10* Gasket (NEMA 3, 4, 4x or 12) 4395-019-01 4395-19 11* Gasket (NEMA 3, 4, 4x or 12) 4395-020-01 4395-20 12 Switch 113-009 13 Round Head Bolt 1/4 20 x 6 Green 764-137 14 Round Head Bolt 1/4 20 x 6 Red 764-137 15 Hex Head Bolt 1/4 20 x 3/4 751-402 16 Hex Lock Nut 1/4 20 752-203 17 Self Tapping Screw #6 32 x 1 765-102 18 Flat Washer 1/2 x 9/32 x 16 GA 753-151 19 Rubber Mounting Plate 4395-124-01 4395-124 20 Flat Washer 5/8 x 9/32 x 16 GA 753-002 22 Adapter Plate 4395-022-01 4395-22 23 Pedestrian Opening Switch Plate 4395-023-01 4395-23 24 Flat Head Self Tapping Screw #6 32 x 1 765-209 25 Self Tapping Screw #10 24 x 3/8 765-309 26 Split Lock Washer #10 753-401 27 Flat Washer 1/2 x 197 x 18 GA 753-100 28 Pedestrian Opening Assy. 4395-024-91 4395-24 *Use item 20 for items 10 and 11 with NEMA 1 housing. Note: See instruction sheet for ordering parts. ECN CS-2169 29
18. DMC ASSEMBLY Ref # Group Finish Offset Name of Part Stock No. Drawing Assy. Digital Power Unit Assy. H4470-094 4470-94 1 Motor Unit; 11.125 Long 133-318 2 Sealtite; 1/2 Flexible Conduit 191-103 3 Galv Sealtite Fitting, Straight 191-305 4 Sealtite Fitting 90 Degree 191-307 5 Sprocket, 40B22; 3.513 PD x 3/4 ID 203-059 6 Drive Sprocket Key, 3/16 x 3/16 x 1 447009901 7 Hex Head Mach Bolt; 5/16-18NC x 3/4 751-410 8 Hex Head Mach Bolt; 5/16-18NC x 1-1/2 751-413 9 Galv Lock Washer, Ext; 5/16 Dia. 753-403 10 Spacer; 3/4 OD 4420-370-01 4420-370 11 Mounting Bracket; 1/2 x 4-1/2 4470-089-01 4470-89 12 Control Panel Assembly 16 x 14 x 8; NEMA1 H4470-093 Note: See instruction sheet for ordering parts. For NEMA 4 & 4x control panel assemblies, see drawing H4470094. ECN CS-2169 30
19. CONTROL PANEL BOX, DMC A. NEMA 1 APPLICATION Ref # Group Finish Offset Name of Part Stock No. Drawing 1 Enclosure 16 x 14 x 8 486-206 2 Control Panel Assy. Bracket 10 GA (2 Required Per Unit) 4470-092-01 4470-92 Notes: See instruction sheet for ordering parts. Enclosure stock numbers are shown for reference only. Warning labels are not included within the enclosure stock applications. Internal components are common for all NEMA applications. For floor loop option see H4480012 For radio control option see H4480013 B. NEMA 4 & 4X APPLICATIONS Ref # Group Finish Offset Name of Part Stock No. Drawing 1 Enclosure 16 x 14 x 8 191-519 2 Control Panel Assy. Bracket 10 GA (2 Required Per Unit) 4470-092-01 4470-92 Notes: See instruction sheet for ordering parts. Enclosure stock numbers are shown for reference only. Warning labels are not included within the enclosure stock applications. Internal components are common for all NEMA applications. For floor loop option see H4480012 For radio control option see H4480013 ECN CS-2169 31
20. DMC CONTROL PANEL ASSEMBLY NOTES: 1. Enclosure not shown. Ref # Group Finish Offset Name of Part Stock No. Drawing 1 Transformer, Toroid 336 W, 50/60 HZ. 115-117 2 Radio Control Multi-Code 1090 119-015 3 Controller Drive Unit 119-213 4 Grounding Lug 191-355 5 Grommet for I Opening 559-046 6 Retainer, Remote Control #16 GA. 4420-383-01 4420-383 7 Bracket, Transformer #12 GA. 4470-090-01 4470-90 8 Baseplate 14.75 x 12.88 (A16P14) 4470-091-01 4470-91 9 Baffle Plate #16 GA. 4470-096-01 4470-96 10 Grounding Wire, Control Panel 14 AWG x 6 Lg. 4390-470-01 4390-470 NOTE: See instruction sheet for ordering parts. DMC control panel is only needed for a DMC drive unit. ECN CS-2169 32
THIS PAGE LEFT BLANK ECN CS-2169 33
21. CONTROL PANEL COMPONENTS CONTINUED, DMC NOTES: 1. Optional component 2. For fuse requirement please see the fuse replacement label within the control panel or contact the factory. ECN CS-2169 34
Ref # Group Finish Offset Name of Part Stock No. Drawing 1 DPDT Relay 111-029 4290-963 2 Relay Socket 111-034 3 Socket, Floor Loop 111-050 4 Transformer Class 2 115-109 4390-434 5 Fuse, 3 Amp FNQ-R-3 116-108 6 Fuse,15 Amp FNQ-R-15 116-111 7 Circuit Breaker, 20 Amp ABB S201-C20 116-117 8 Fuse, 6A FNQ-R-6 116-118 9 Fuse, 12A FNQ-R-12 116-119 10 Fuse, 25A FNQ-R-25 116-120 11 Floor Loop Module 326SF24A-7; Harness 802A-4 119-014 12 End Stop 170-004 13 Fuse Block 170-020 14 2-Pin Jumper 170-026 15 3-Pin Jumper 170-027 16 Terminal Block Beige, ZDU2. 5/3AN 170-028 17 Terminal Block Orange, ZDU2. 5/3AN 170-030 18 Terminal Block, Ground 170-045 19 Terminal Barrier, Ground ZAP / TW3 170-046 20 Terminal Block Relay Allen Bradley 700-HLT-2Z12 170-047 21 Terminal Barrier, Block ZAP / TW2 170-048 22 Din Rail 35mm x 8in 4390-406-03 4390-406 Note: See instruction sheet for ordering parts. ECN CS-2169 35
22. CONTROL PANEL COMPONENTS CONTINUED, DMC 575 V NOTES: 1. Optional component 2. For fuse requirement please see the fuse replacement label within the control panel or contact the factory. Ref # Group Finish Offset Name of Part Stock No. Drawing 1 DPDT Relay 111-029 4290-963 2 Relay Socket 111-034 3 Socket, Floor Loop 111-050 4 Transformer 575V 115-113 5 Fuse, 2A FNM-2 116-103 6 Fuse, 3A FNQ-R-3 116-108 7 Fuse, 5A FNQ-R-5 116-109 8 Circuit Breaker, 20 Amp ABB S201-C20 116-117 9 Floor Loop Module 326SF24A-7 Harness 802A-4 119-014 10 End Stop 170-004 11 Fuse Block 170-020 12 2-Pin Jumper 170-026 13 3-Pin Jumper 170-027 14 Terminal Block Beige, ZDU2. 5/3AN 170-028 15 Terminal Block Orange, ZDU2. 5/3AN 170-030 16 Terminal Block, Ground 170-045 17 Terminal Barrier, Ground ZAP / TW3 170-046 18 Terminal Block Relay Allen Bradley 700-HLT-2Z12 170-047 19 Terminal Barrier, Block ZAP / TW2 170-048 20 Din Rail 35mm x 8in 4390-406-03 4390-406 Note: See instruction sheet for ordering parts. ECN CS-2169 36
23. JAMECO CONTROL BOX ECN CS-2169 37
Ref # Group Finish Offset Name of Part Stock Stock No. No. Drawing 1 Toggle Switch 113118 2 Humidity based fan control 113119 3 Receptacle cover 113120 4 Wire SO18/3 123120 5 Fork Terminal 170067 6 Ring Terminal 170068 7 3C Compact Splice 170069 8 5C Compact Splice 170070 9 2-Gang Lug Box 191549 10 Liquidtight Cord Grip 191550 ECN CS-2169 38
24. PULL CORD SWITCH Ref # Group Finish Offset Name of Part Stock No. Drawing No. Assy. Complete WPS Switch (W/o Heat) 113-218 Assy. Complete WPS Switch (W/ Heat) 113-219 1 Pull Cord Rope W/ Tassel (Not Shown) 4285-059-02 4285-59 1 Pull Cord Rope Vinyl 60 (Not Shown) 4285-049-01 4285-49 Note: See instruction sheet for ordering parts. ECN CS-2169 39
25. MANUAL DISCONNECT Ref # Group Finish Offset Name of Part Stock No. Drawing No. S Assy. Complete Sub-Assy. (W/ Thru-Door Operator) (4 Door) (1,2,3A,4,5,7) 4404-417-01 4404-417 S Assy. Complete Sub-Assy. (for RH Leaf Bi-Part) (4 Door) (1,3B,4,7) 4404-417-02 4404-417 S Assy. Complete Sub-Assy. (W/ Thru-Door Operator) (6 Door) 4404-417-03 4404-417 1 Cable Boss 486-156 2 Push Nut 752-502 3A Washer (Thru-Door Operator) 4404-388-01 4404-388 3B Stub Shaft/Washer 4404-410-01 4404-410 4 Pop Rivet 755-365 5 Back Handle Sub-Assy. (4 Door) 486-155 5A Back Handle Sub-Assy. (2 Door) 4404-542-01 4404-542 5B Back Handle Sub-Assy. (6 Door) 4404-527-01 4404-527 6* Disconnect Cable (Advise H.I.C., Date of Mfg and Handle) 204-325 4404-418 7 Set-Screw 767-131 8 Vinyl Cable End Cap 191-351 9 Turn Handle For Manual Release Label 996-040 Note: See instruction sheet for ordering parts. ECN CS-2169 40
THIS PAGE LEFT BLANK ECN CS-2169 41
26. FRONT PADLOCKING HARDWARE ECN CS-2169 42
Ref # Group Finish Offset Name of Part Stock No. Drawing No. 1 SST Safety Release Handle (4 Door) 4243-664-01 4243-664 1 SST Safety Release Handle (2 Door) 4243-664-02 4243-664 1 SST Safety Release Handle (6 Door) 4243-664-03 4243-664 2 Galv Washer 753-017 2 SST Washer 753-155 3 Alum Door Cup W/o Hole 4038-008-01 4038-8 3 Alum Door Cup W/ Hole 4038-008-03 4038-8 3 Door Cup W/ Hole (Powder Coat Chrome) 4038-008-04 4038-8 4 Pop Rivet 755-365 5 Galv Staple Lock Washer 4243-060-01 4243-60 5 Chr Staple Lock Washer 4243-060-02 4243-60 6 Phenolic Washer 753-306 7 Galv Staple Eye 4243-059-03 4243-59 7 Chr Staple Eye 4243-059-04 4243-59 8 SST Switch Plate Sub-Assy. (Power Doors Only) 4243-686-01 4243-686 9 Pop Rivets (Power Doors Only) 755-357 10 Galv Hasp Blade Mounting Angle Sub-Assy. (4 ) (Manual) 4243-655-01 4243-655 10 Chr Hasp Blade Mounting Angle Sub-Assy. (4 ) (Manual) 4243-655-02 4243-655 10 Galv Hasp Blade Mounting Angle Sub-Assy. (4 ) (Power) 4243-655-03 4243-655 10 Chr Hasp Blade Mounting Angle Sub-Assy. (4 ) (Power) 4243-655-04 4243-655 10 Galv Hasp Blade Mounting Angle Sub-Assy. (6 ) (Manual) 4243-655-05 4243-655 10 Chr Hasp Blade Mounting Angle Sub-Assy. (6 ) (Manual) 4243-655-06 4243-655 10 Galv Hasp Blade Mounting Angle Sub-Assy. (6 ) (Power) 4243-655-07 4243-655 10 Galv Hasp Blade Mounting Angle Sub-Assy. (6 ) (Power) 4243-655-08 4243-655 10 Galv Hasp Blade Mounting Angle Sub-Assy. (2 ) (Manual) 4243-655-09 4243-655 10 Galv Hasp Blade Mounting Angle Sub-Assy. (2 ) (Power) 4243-655-11 4243-655 10A SST Hasp Blade Mounting Angle (2 ) 4243-704-01 4243-704 10B SST Hasp Blade Mounting Angle (4 ) 4243-654-01 4243-654 10C SST Hasp Blade Mounting Angle (6 ) 4243-703-01 4243-703 11 Magnet (Power Doors Only) 113-005 12 Galv Hasp Blade Sub-Assy. (Manual Bi-parting Door) 4243-381-01 4243-381 12 Chr Hasp Blade Sub-Assy. (Manual Bi-parting Door) 4243-381-02 4243-381 13 Galv Staple 4243-028-01 4243-28 13 Chr Staple 4243-028-02 4243-28 15 Galv Hasp Blade Sub-Assy. W/o Emergency Release 4 door, (Not a Stock Item) H4243-672-01 4243-672 15 SST Hasp Blade Sub-Assy. W/o Emergency Release 4 door, (Not a Stock Item) H4243-672-02 4243-672 16 Self Tapping Screw 769-102 17 Pop Rivet 755-366 Note: See instruction sheet for ordering parts. ECN CS-2169 43
27. PNEUMATIC REVERSING EDGE Ref # Group Finish Offset Name of Part Stock No. Drawing No. Assy. Complete Assy. (When Ordering Specify Door Model, Serial Number, Size and Slide) 4404-420-XX 4404-420 1 Outer Gasket Wrapper (.035 X 5 ) (HIC + 1/2 ) (Specify Length Required) 552-165 2 Inner Wrapper (.04 X 3-3/8 ) (Ripstop Nylon) (HIC 3-1/2 ) 552-166 3 Switch 113-113 4 Bushing 559-041 5 Hose (Specify Length Required) 559-100 6 End Plug (to be Glued in Place) 4390-167-01 4390-167 7 Plug 4404-855-01 4404-855 8 Sub Base (Specify Length) 4404-757-XX Note: See instruction sheet for ordering parts. ECN CS-2169 44
THIS PAGE LEFT BLANK ECN CS-2169 45
28. MISCELLANEOUS DOOR PARTS ECN CS-2169 46
Ref # Group Finish Offset Name of Part Stock No. Drawing 1 SST Leading Edge Wedge (4 & 6 ) (Single Door Only) 4404-495-01 4404-495 1A SST Leading Edge Wedge (2 ) (Single Door Only) 4404-552-01 4404-552 2 Alum Front and Rear Strafing Bar 2 Single 5 0 WIC 4404-381-01 4404-381 2 Single 6 0 WIC 4404-381-02 4404-381 2 Bi-Part (Front) 6 0 WIC 4404-382-02 4404-382 2 Bi-Part (Rear) 6 0 WIC 4404-383-02 4404-383 2 Single 7 0 WIC 4404-381-03 4404-381 2 Bi-Part (Front) 7 0 WIC 4404-382-03 4404-382 2 Bi-Part (Rear) 7 0 WIC 4404-383-03 4404-383 2 Single 8 0 WIC 4404-381-04 4404-381 2 Bi-Part (Front) 8 0 WIC 4404-382-04 4404-382 2 Bi-Part (Rear) 8 0 WIC 4404-383-04 4404-383 2 Single 10 0 WIC 4404-381-06 4404-381 2 Bi-Part (Front) 10 0 WIC 4404-382-06 4404-382 2 Bi-Part (Rear) 10 0 WIC 4404-383-06 4404-383 3 SST Trailing Edge Wedge (4 Door) 4404-379-01 4404-379 3A SST Trailing Edge Wedge (2 Door) 4404-543-01 4404-543 3B SST Trailing Edge Wedge (6 Door) 4404-507-01 4404-507 4 Sill Gasket (.04 X 2-3/8 ) (Hypalon) 552-151 5 Galv Front Door Pull 251-010 5 Chr Front Door Pull 4038-001-02 4038-1 6 Alum Rear Door Pull Cup 4038-008-01 4038-8 6 Rear Door Pull Cup (Powder Coat Chrome) 4038-008-02 4038-8 6 Alum Rear Door Pull Cup, 7 4318-211-01 4318-211 6 Rear Door Pull Cup, 7 (Powder Coat Chrome) 4318-211-02 4318-211 7 Alum Rear Door Pull Bar 4038-013-01 4038-13 7 Rear Door Pull Bar (Powder Coat Chrome) 4038-013-02 4038-13 7 Alum Rear Door Pull Bar, 7 4038-029-01 4038-29 8 Rubber Bumper 559-040 9 Track Wedge 932-008 10 Galv Reversing Edge Retainer 4404-386-04 4404-386 10 SST Reversing Edge Retainer 4404-386-14 4404-386 11 Frame Wedge 931-021 12 Ped. Opening Push Button Switch 113-003 4404-415 13 Wicket Door Cut-Out Switch 113-006 4404-493 Note: See instruction sheet for ordering parts. ECN CS-2169 47
29. GASKET ASSEMBLY ECN CS-2169 48
Ref # Group Finish Offset Name of Part Stock No. Drawing 1* Gasket Sub-Assembly Horiz. (White) 1* 5 0 4404-010-01 4404-10 1* 6 0 4404-010-02 4404-10 1* 7 0 4404-010-03 4404-10 1* 8 0 4404-010-04 4404-10 1* 9 0 4404-010-05 4404-10 1* 10 0 4404-010-06 4404-10 2* Gasket Sub-Assy. Vert. (White) (Specify Hand) 2* 6 0 4404-010-11 4404-10 2* 7 0 4404-010-12 4404-10 2* 8 0 4404-010-13 4404-10 2* 9 0 4404-010-14 4404-10 2* 10 0 4404-010-15 4404-10 3* Gasket Retainer 3* SST 5 0 LH 4404-016-21 4404-16 3* SST 5 0 RH 4404-016-71 4404-16 3* SST 6 0 LH 4404-016-22 4404-16 3* SST 6 0 RH 4404-016-72 4404-16 3* SST 7 0 LH 4404-016-23 4404-16 3* SST 7 0 RH 4404-016-73 4404-16 3* SST 8 0 LH 4404-016-24 4404-16 3* SST 8 0 RH 4404-016-74 4404-16 3* SST 9 0 LH 4404-016-25 4404-16 3* SST 9 0 RH 4404-016-75 4404-16 3* SST 10 0 LH 4404-016-26 4404-16 3* SST 10 0 RH 4404-016-76 4404-16 3A Head Gasket Retainer (Order Reference 3, RH) 4 SST Pan Head Screw #14 x 2 765-361 5* Gasket Outer Wrapper.04 x 5 552-165 6* Flat Gasket Retainer for Doors w/jambs (Not Shown) 4404-422-xx 4404-422 7 Screw (for Flat Gasket Retainer) 765-359 8 Gasket Heat Wire (Call Factory w/serial Number) xxx-xxx *Please specify the HIC and WIC of the door that the item is to be used on. Note: See instruction sheet for ordering parts. ECN CS-2169 49
30. OPTIONAL PULL BAR HANDLE (SINGLE MANUAL DOOR ONLY) Ref # Group Finish Offset Name of Part Stock No. Drawing No. Assy. Complete Assy. (Items 3, 4, & 5 Not Included) H4475-009 4475-9 1 Oilite Bearing 481-318 2 Shaft Collar 489-402 3 Taptite, Hex Head 5/16 X 1 769-105 4 Taptite, Hex Head 3/8 X 1 769-102 5 Opener Bracket 4475-001-01 4475-1 6 Oilite Bearing Modified 4475-004-01 4475-4 7 Bottom Bracket 4475-006-01 4475-6 8 Top Bracket 4475-007-01 4475-7 9 Handle Assy. 4475-008-01 4475-8 Note: See instruction sheet for ordering parts. ECN CS-2169 50