INSTALLATION INSTRUCTIONS This document explains mounting for pendant, recessed, and wall
PENDANT - STEP ONE INSTALL MOUNTING POINTS Non-power feed mounting points may be positioned 1 to 12 or 12 to 18 from the end of the luminaire. Recommended that mounting point be positioned within 12 inches of end cap for support Reference Continuous Run Guide at for additional information. 2ft 17.35 MIN 23.35 MAX = Power Feed Canopy 25.675 MIN 35.68 MAX = Non-Power Feed Canopy 3ft 33.68 MIN 47.68 MAX 4ft 51.68 MIN 71.68 MAX 6ft 71.35 MIN 95.35 MAX 8ft 1/9
PENDANT - STEP TWO INSTALL POWER FEED MOUNT All electrical circuits should be turned off before starting work. Please follow local and national electrical codes. Junction Box A - Install junction box (not included) at appropriate location. B - Feed power wires into junction box and ground appropriately. C - Install Bracket Bar to junction box using ground screws. D - Install Threaded Stud into Bracket Bar. E - Feed Aircraft Cable and through Terminals and Threaded Stud. Tapped 1/4-20 Threaded Stud Bracket Bar F - Thread Canopy on to aircraft cable. Power Feed Canopy 2 piece Terminals Strain Relief Bushing Power Cable 1/16 Aircraft Cable Gripper 2/9
PENDANT - STEP THREE INSTALL NON-POWER FEED MOUNT A - Install threaded stud (not included) into ceiling. B - Install non-power feed canopy onto threaded stud. C - Install aircraft cable and terminal to hold canopy in place. Tapped 1/4-20 Threaded Stud Non-Power Feed Canopy Terminal 1/16 Aircraft Cable Gripper 3/9
PENDANT - STEP FOUR HANG LUMINAIRE A - Lift luminaire into place, and insert aircraft cables into cable grippers B - Adjust height of luminaire and level. Luminaire can be raised by pulling cable through the gripper and can be lowered by depressing the top cylinder on the gripper which pulls the luminaire down. C - Make sure all parts are tightened and insert strain relief into canopy. D - Snap cable clip on top of housing making sure it clicks completely. clip on rails of top of the housing it clicks all the way at both sides Adjust cables by gliding along the housing. 4/9
PENDANT CONTINUOUS RUNS Reference Continuous Run Guide at for additional information. A - Perform Steps 1 through 4 installing as many mounting points as required. B - Remove lens and light engines. Pull out light engine tray 1. Use small flat head screw driver or blade to pop lens out at ends of the fixture. 2. Squeeze clips to release tray. 3. Pull out light engine. C - Hang 2nd luminaire by feeding aircraft cable into cable gripper on the end of the 2nd luminaire section. D - Use provided Quick Connects to create electrical connections to 1st and 2nd sections. E - Slide joiner/aligner from 2nd section into 1st section. F - Use Connection Bracket to connect luminaire sections together. DO NOT TIGHTEN COMPLETELY. G - Level 2nd section. H - Insert lens and light engines. I - Tighten Connection Bracket completely. 5/9
RECESSED FLANGED MOUNTING OPTIONS Reference Surface Installation Instructions for Recessed Flangeless mounting instructions Dimensions and illustrations shown on this page are for Vector 2 only. Fixture Width 2.44 2.75 Slot Width RECESSED BRACKETS THREADED ROD FASTENERS 6/9
RECESSED FLANGED RECESSED BRACKETS Make sure path of bracket location is free of obstacles Architectural LED Luminaire TM A. Cut out slot for housing. B. Follow directions below: 1. Take out knock out plate and install power whip. 2. Use small flat head screw driver or blade to pop lens out at ends of the fixture. 3. Squeeze clips to release tray. 4. Pull out light engine. 5. Set brackets on back of housing and insert 10/24 screws from INSIDE the housing. 6. Screw in knock out plate. 1/2 11.02.2017 t : 310.366.6866 f : 310.366.6855 800.613.DECO (3326) Copyright Deco Lighting, Inc. 2017
RECESSED FLANGED RECESSED BRACKETS Make sure path of bracket location is free of obstacles Architectural LED Luminaire TM 7. Insert fixture into ceiling. 8. Tighten screws inside fixture to tighten brackets 9. Recessed brackets will tighten automatically to secure in place. Insert recessed housings and slide aligner bracket into place between housings. This piece will float. C. Use provided Quick Connects to create electrical connections. D. Insert lens and light engines back into fixture. 2/2 11.02.2017 t : 310.366.6866 f : 310.366.6855 800.613.DECO (3326) Copyright Deco Lighting, Inc. 2017
WALL MOUNTING BRACKETS Make sure path of bracket locations are free of obstacles 1 A - Install Bracket #1 with screws provided. A B - Feed power wires and ground appropriately. C C - Hook in Bracket #2 which arrives pre-installed. D - Screw in additional screws at bottom of bracket if desired. 2 x 4 Switch Box B 2B A1 4.00 4.00 4 4.00 4 A 2.125 2B 1 4 4.00 2 A D 4 Octagonal Junction Box B 2 ft 3 ft 4 ft 6 ft 8 ft A B 16.00 16.00 32.00 32.00 406.4mm 406.4mm 812.8mm 812.8mm 4.00 101.6mm 10.00 254.0mm 8.00 203.2mm 20.00 508.0mm 64.00 1625.6mm 16.00 406.4mm 3 A C 2.50 2.50 2.50 2.50 2.50 63.5mm 63.5mm 63.5mm 63.5mm 63.5mm C D 3.10 78.74mm 3.10 78.74mm 3.10 78.74mm 3.10 78.74mm 3.10 78.74mm 2 x 4 Switch Box B 9/9