Table of Contents Part Number Index Rotary Cutter RCR2596, RCR2510 & RCRM2510 22352 312-753P Parts Manual Read the Operator's Manual entirely. When you see this symbol, the subsequent instructions and warnings are serious - follow without exception. Your life and the lives of others depend on it! Copyright 2017 Printed 07/14/17 Cover photo may show optional equipment not supplied with standard unit.
Table of Contents Part Number Index Table of Contents Section 1: Introduction...4 Using This Manual...4 Manual Replacement Information...4 Manual Revisions...4 Touch-up Paint...4 Hardware Legend...5 Replacement Hardware...5 Serial Numbers...5 Part Number Service Coding...5 Section 2: Frame...6 3-Point Wheel...6 CV Trail Type Driveline...8 Deck Blade Drive S/N 644967-...10 Deck Blade Drive S/N 644968 to 98349...12 Deck Blade Drive S/N 983493+...14 Deck Components & 3-Point Hitch...16 Equal Angle Pull Type Driveline...20 Hydraulic Lift...22 Pull Type...24 Pull Type Axle and Tires...26 Section 3: Guards...28 Guarding Chain...28 Guarding Chain...30 Guarding Rubber...32 Guarding Rubber...34 Section 4: Drivelines...36 Coupler Intermediate 826-646c & 826-647c...36 Driveline 1000 RPM (826-216C) Eurocardan...38 Driveline 1000 RPM (826-221C) Eurocardan...40 Driveline 1000 RPM (826-223C) Eurocardan...42 Driveline 1000 RPM (826-226C) Eurocardan...44 Driveline 540 RPM (826-151C) Eurocardan...46 Driveline 540 RPM (826-215C) Eurocardan...48 Driveline 540 RPM (826-220C) Eurocardan...50 Driveline 540 RPM (826-255C) Eurocardan...52 Driveline 540 RPM (826-256C) Eurocardan...54 Driveline CV 1000 RPM (826-063C) Walterscheid...56 Driveline CV Pull Type Cutter 540 RPM (826-053C) Walterscheid...58 Driveline Flex Coupler (826-359C) Eurocardan...60 Driveline Flex Coupler (826-360C) Eurocardan...62 Driveline Slip Clutch (1406016) Eurocardan...64 Driveline Slip Clutch (1406028) Eurocarda...66 Driveline Slip Clutch (1406128) EC...68 Driveline Slip Clutch (1446016) Eurocardan...70 Driveline Slip Clutch (1446037) Eurocardan...72 Driveline Slip Clutch (1446137) Eurocardan...74 Driveline Slip Clutch 1000 RPM (1406116) Eurocardan...76 Driveline Stub Shaft Pull Type 540 RPM (826-225C) Eurocardan...78 Section 5: Gearboxes...80 Gearbox (826-358C) Comer...80 Gearbox (826-424C) Comer...82 Gearbox...84 T-Box 540 RPM (826-356C) Comer...84 Section 6: Hydraulics...86 Hydraulic Cylinder (810-200C) Midway...86 Hydraulic Cylinder (810-200C) Red Lion...88 Section 7: Labels...90 Label Placement S/N 983492-...90 Label Placement S/N 983493+...92 Touch-up Paints...94 Part Number Index...96 Copyright 2017. All rights reserved. provides this publication as is without warranty of any kind, either expressed or implied. While every precaution has been taken in the preparation of this manual, assumes no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of the information contained herein. Land Pride reserves the right to revise and improve its products as it sees fit. This publication describes the state of this product at the time of its publication, and may not reflect the product in the future. The illustrations in this manual are not intended for safe and proper assembly or disassembly of equipment. The illustrations are intended for ordering parts only. is registered trademark. All other brands and product names are trademarks or registered trademarks of their respective holders. Printed in the United States of America. 2 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Table of Contents Part Number Index Alphabetized Table of Contents 3 C 3-Point Wheel...6 Coupler Intermediate 826-646c & 826-647c...36 CV Trail Type Driveline...8 P Touch-up Paints...94 Pull Type...24 Pull Type Axle and Tires...26 D Deck Blade Drive S/N 644967-...10 Deck Blade Drive S/N 644968 to 98349...12 Deck Blade Drive S/N 983493+...14 Deck Components & 3-Point Hitch...16 Driveline 1000 RPM (826-216C) Eurocardan...38 Driveline 1000 RPM (826-221C) Eurocardan...40 Driveline 1000 RPM (826-223C) Eurocardan...42 Driveline 1000 RPM (826-226C) Eurocardan...44 Driveline 540 RPM (826-151C) Eurocardan...46 Driveline 540 RPM (826-215C) Eurocardan...48 Driveline 540 RPM (826-220C) Eurocardan...50 Driveline 540 RPM (826-255C) Eurocardan...52 Driveline 540 RPM (826-256C) Eurocardan...54 Driveline CV 1000 RPM (826-063C) Walterscheid...56 Driveline CV Pull Type Cutter 540 RPM (826-053C) Walterscheid...58 Driveline Flex Coupler (826-359C) Eurocardan...60 Driveline Flex Coupler (826-360C) Eurocardan...62 Driveline Slip Clutch (1406016) Eurocardan...64 Driveline Slip Clutch (1406028) Eurocarda...66 Driveline Slip Clutch (1406128) EC...68 Driveline Slip Clutch (1446016) Eurocardan...70 Driveline Slip Clutch (1446037) Eurocardan...72 Driveline Slip Clutch (1446137) Eurocardan...74 Driveline Slip Clutch 1000 RPM (1406116) Eurocardan...76 Driveline Stub Shaft Pull Type 540 RPM (826-225C) Eurocardan...78 E Equal Angle Pull Type Driveline...20 G Gearbox (826-358C) Comer...80 Gearbox (826-424C) Comer...82 Gearbox, T-Box 540 RPM (826-356C) Comer...84 Guarding Chain...28 Guarding Chain...30 Guarding Rubber...32 Guarding Rubber...34 H Hydraulic Cylinder (810-200C) Midway...86 Hydraulic Cylinder (810-200C) Red Lion...88 Hydraulic Lift...22 L Label Placement S/N 983492-...90 Label Placement S/N 983493+...92 07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 3
Table of Contents Part Number Index 4 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Table of Contents Part Number Index 07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 5
3-Point Wheel Table of Contents Part Number Index Section 2: Frame Applies to RCR2510, RCR2596, RCRM2510 22334 6 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Section 2: Frame 3-Point Wheel Table of Contents Part Number Index Applies to RCR2510, RCR2596, RCRM2510 Ref. Part No. Part Description Comments Revision 6. 7. 8. 9. 10. 1 1 1 1 1 16. 17. 18. 19. 20. 2 2 2 2 2 26. 27. 28. 29. Dwg 22334 312-616D 312-810D 312-811D 327-129H 312-614H 312-512H 800-001C 800-080C 802-106C 802-135C 802-162C 802-280C 802-326C 803-026C 803-037C 803-271C 803-289C 803-308C 804-015C 804-016C 804-066C 805-255C 814-058C 814-161C 815-092C 815-230C 815-231C 816-286C 822-091C 822-092C 827-036C 890-961C Drawing Image Number TAILWHEEL ARM ADJUST PLATE TAILWHEEL BEAM ADJ. BRKT. TAILWHEEL BEAM MOUNTING BRKT. TAILWHEEL BEAM WLDMT SHORT WLDMT TAILWHEEL BEAM TAILWHEEL BEAM WELDMENT GREASE ZERK STRAIGHT 1/4-28 GREASE ZERK 1/4-28 THD FORMING RHSNB 1/2-13X1 1/2 GR5 HUB STUD 1/2-20X1 5/8 GR5 HHCS 5/8-11X3 1/2 GR5 HHCS 3/4-10X7 1/2 GR5 HHCS 1/2-20X1 1/4 GR5 NUT LOCK 3/4-10 PLT NUT HEX WHIZ 1/2-13 PLT NUT HEX TOP LOCK 5/8-11 PLT NUT HEX 1 1/4-7(MACHINED)PLAIN NUT HEX FLG/LK 1/2-20 PLT GR G WASHER LOCK SPRING 1/2 PLT WASHER FLAT 1/2 SAE PLT WASHER MACH 25 X 50 X 14GA PIN ROLL 3/8 X 2 1/2 PLT TIRE & WHEEL LAMINATED 0 X 8 LAM 4X8 TR-WL-HUB-YOKE 25 SER. HUB & SPINDLE ASSY 4 BOLT HUB 4 BLT W/CUPS, ZERK & STUDS HUB 4BLT DUCTILE(USE 815-230C) OIL SEAL DBL LIP 441 BORE BRG 25ID CONE 15123 BRG CUP 44OD 15245 BUSHING TW 25ODX.78IDX5 1/4 RC25 TAILWHEEL YOKE, 5 SHAFT RCR2596 RCR(M)2510 RCR2596 S/N 847909+ RCR2596 S/N 847908- RCR(M)2510 07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 7
Table of Contents CV Trail Type Driveline Applies to RCR2510, RCRM2510 Part Number Index Section 2: Frame 22342 8 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Table of Contents CV Trail Type Driveline Section 2: Frame Applies to RCR2510, RCRM2510 Part Number Index Ref. Part No. Part Description Comments Revision 6. 7. 8. 8. 9. 9. Dwg 22342 312-820D 800-073C 801-035C 802-034C 802-082C 803-037C 822-094C 826-053C 826-063C 826-225C 826-226C Drawing Image Number PILLOW BLOCK BRG. SUPPORT GREASE ZERK 1/4-28 X 90-DEG SCREW SET 5/16-18 SKT KP X 3/8 HHCS 1/2-13X1 1/4 GR5 HHCS 1/2-13X1 3/4 GR5 NUT HEX WHIZ 1/2-13 PLT BEARING PILLOW BLOCK 1 3/8BORE PTO CV 2400 X 60 540 RPM PTO CV 2400 X 60 1000 RPM PTO W/STUB SHAFT/SC 540 1 3/4 PTO W/STUB SHAFT/SC 1000 1 3/4 RCR2510 RCRM2510 RCR2510 RCRM2510 07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 9
Table of Contents Deck Blade Drive S/N 644967- Applies to RCR2510, RCR2596, RCRM2510 Part Number Index Section 2: Frame 22333 10 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Table of Contents Deck Blade Drive S/N 644967- Section 2: Frame Applies to RCR2510, RCR2596, RCRM2510 Part Number Index Ref. Part No. Part Description Comments Revision 6. 7. 7. 8. 9. 10. 1 1 1 1 1 16. 17. 18. 18. 18. 18. 18. 19. 19. 19. 19. 19. 20. 20. 20. 2 2 2 2 2 2 2 2 2 2 26. 27. Dwg 22333 312-765H 312-767H 312-748H N/A N/A 326-116D 326-101D 802-034C 802-065C 802-064C 802-277C 802-314C 803-170C 803-299C 804-015C 804-147C 804-157C 804-161C 817-165C 817-259C 820-615C 820-195C 820-210C 820-137C 820-193C 820-614C 820-196C 820-211C 820-112C 820-209C 826-255C 826-215C 826-216C 826-356C 826-424C 826-358C 826-360C 826-359C 312-075D 312-082D 312-089D 312-808D 800-001C 826-497C 318-586A Drawing Image Number SHIELD BRACKET WELDMENT DISHPAN WELDMENT 15" CTR DISHPAN WELDMENT 17" CTR CW BLADE CARRIER ASSY CCW BLADE CARRIER ASSY2 OUTER SHIELD OUTER SHIELD HHCS 1/2-13X1 1/4 GR5 HHCS 3/4-10X2 1/4 GR5 HHCS 3/4-10X2 GR5 BLADE BOL 1 1/8-12X3 7/16 W/KY HHCS M8X25X20 GR8.8 NUT HEX TOP LOCK 1 1/8-12 PLT. NUT HEX FLG TOP LK 3/4-10 PLT WASHER LOCK SPRING 1/2 PLT WASHER FLAT 1" HARDENED WASHER SPRING LOCK M8 PLT WASHER FLAT M8 PLT GRBOX SHAFT(1 3/4OD) PROTECTOR KNOB 3/8-16 FEMALE THD 2 3/8OD CUTTER BLADE 1/2X4X20.5 CCW CUTTER BLADE 1/2X4X20 1/2 CCW CUTTER BLADE 1/2X4X20.5 LL CCW CUTTER BLADE 1/2 X 4 X 25 CCW CUTTER BLADE 1/2X4X25 LL CCW CUTTER BLADE 1/2X4X20.5 CW CUTTER BLADE 1/2X4X20 1/2 CW CUTTER BLADE 1/2X4X20.5 LL CW CUTTER BLADE 1/2 X 4 X 25 CW CUTTER BLADE 1/2X4X25 LL CW PTO STD.W/4-PLATE SC CAT4 540 PTO STD.W/4-PLATE SC CAT4 540 PTO STD.W/2-PLATE SC CAT4 1000 T-BOX 75-20 1:35 T-BOX 75-20 35:1 GBOX 1:50 STD. 38-6 SPL. FLEX CPLR 75-20 TO 38-6 S FLEX CPLR 75-20 TO 38-6 BLADE SPACER 16 GA.06 thick BLADE SPACER 18 GA.05 thick BLADE SPACER 20 GA..04 thick BLADE SPACER 24GA.03 thick GREASE ZERK STRAIGHT 1/4-28 COMER VENT #8.6.7.00269 BLADE BOLT KIT RCR2596 RCR(M)2510 RCR2596 RCR2510 (S/N 558465+) (S/N 558464-) RCR2596 Standard S/N 1000427+ RCR2596 Standard S/N 1000426- RCR2596 Optional RCR2510 RCRM2510 Standard RCR2510 RCRM2510 Optional RCR2596 Standard S/N 1000427+ RCR2596 Standard S/N 1000426- RCR2596 Optional RCR2510 RCRM2510 Standard RCR2510 RCRM2510 Optional RCR2596 RCR2510 RCRM2510 RCR2596 RCR2510 RCRM2510 RCR2596 RCR2510 RCRM2510 As Required As Required As Required As Required 07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 11
Deck Blade Drive S/N 644968 to 983492 Section 2: Frame Applies to RCR2510, RCR2596, RCRM2510 30117 12 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Deck Blade Drive S/N 644968 to 983492 Section 2: Frame Applies to RCR2510, RCR2596, RCRM2510 Ref. Part No. Part Description Comments Revision 6. 6. 7. 8. 9. 10. 1 1 1 1 1 16. 17. 18. 19. 20. 20. 20. 20. 20. 2 2 2 2 2 2 2 2 2 2 2 2 26. 27. 27. 28. Dwg 30117 312-075D 312-082D 312-089D 312-808D 312-765H 312-767H 312-748H N/A N/A 326-116D 326-101D 802-034C 802-065C 802-277C 802-314C 803-170C 803-299C 804-015C 804-147C 804-157C 804-161C 816-298C 817-165C 817-259C 820-615C 820-195C 820-210C 820-137C 820-193C 820-614C 820-196C 820-211C 820-112C 820-209C 826-255C 826-215C 826-216C 826-356C 826-424C 826-358C 826-497C 826-503C 826-646C 826-647C 318-586A Drawing Image Number BLADE SPACER 16 GA.06 THICK BLADE SPACER 18 GA.05 THICK BLADE SPACER 20 GA.04 THICK BLADE SPACER 24 GA.03 THICK SHIELD BRACKET WELDMENT DISHPAN WELDMENT 15 CTR DISHPAN WELDMENT 17" CTR CW BLADE CARRIER ASSY CCW BLADE CARRIER ASSY OUTER SHIELD OUTER SHIELD HHCS 1/2-13X1 1/4 GR5 HHCS 3/4-10X2 1/4 GR5 BLADE BOL 1 1/8-12X3 7/16 W/KY HHCS M8X25X20 GR8.8 NUT HEX TOP LOCK 1 1/8-12 PLT. NUT HEX FLG TOP LK 3/4-10 PLT WASHER LOCK SPRING 1/2 PLT WASHER FLAT 1" HARDENED WASHER SPRING LOCK M8 PLT WASHER FLAT M8 PLT RUBBER PLUG 1 3/8 W/CROSS SLIT GRBOX SHAFT(1 3/4OD) PROTECTOR KNOB 3/8-16 FEMALE THD 2 3/8OD CUTTER BLADE 1/2X4X20.5 CCW CUTTER BLADE 1/2X4X20 1/2 CCW CUTTER BLADE 1/2X4X20.5 LL CCW CUTTER BLADE 1/2 X 4 X 25 CCW CUTTER BLADE 1/2X4X25 LL CCW CUTTER BLADE 1/2X4X20.5 CW CUTTER BLADE 1/2X4X20 1/2 CW CUTTER BLADE 1/2X4X20.5 LL CW CUTTER BLADE 1/2 X 4 X 25 CW CUTTER BLADE 1/2X4X25 LL CW PTO STD.W/4-PLATE SC CAT4 540 PTO STD.W/4-PLATE SC CAT4 540 PTO STD.W/2-PLATE SC CAT4 1000 T-BOX 75-20 1:35 T-BOX 75-20 35:1 GBOX 1:50 STD. 38-6 SPL. COMER VENT #8.6.7.00269 COMER VENT 8.6.7.00161 CPLR, 75-20X38-6X10.31 FLE CPLR, 75-20X38-6X16.56 FLE BLADE BOLT KIT As Required S/N 776426- As Required S/N 776426- As Required S/N 776426- As Required S/N 776426- RCR2596 RCR(M)2510 RCR2596 RCR(M)2510 RCR2596 Standard S/N 1000427+ RCR2596 Standard S/N 1000426- RCR2596 Optional RCR2510 RCRM2510 Standard RCR2510 RCRM2510 Optional RCR2596 Standard S/N 1000427+ RCR2596 Standard S/N 1000426- RCR2596 Optional RCR2510 RCRM2510 Standard RCR2510 RCRM2510 Optional RCR2596 RCR2510 RCRM2510 RCR2596 RCR2510 RCRM2510 RCR2596 RCR(M)2510 07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 13
Table of Contents Deck Blade Drive S/N 983493+ Applies to RCR2510, RCR2596, RCRM2510 Part Number Index Section 2: Frame 39387 14 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Table of Contents Deck Blade Drive S/N 983493+ Section 2: Frame Applies to RCR2510, RCR2596, RCRM2510 Part Number Index Ref. Part No. Part Description Comments Revision 6. 6. 7. 8. 9. 10. 1 1 1 1 1 16. 17. 18. 19. 19. 19. 19. 19. 20. 20. 20. 20. 20. 2 2 2 2 2 2 2 2 26. 26. 27. 28. Dwg 39387 312-075D 312-082D 312-089D 312-808D 312-765H 312-767H 312-748H N/A N/A 327-498D 327-499D 802-034C 802-065C 802-277C 802-314C 803-170C 803-299C 804-015C 804-147C 804-157C 804-161C 817-165C 817-259C 820-614C 820-196C 820-211C 820-112C 820-209C 820-615C 820-195C 820-210C 820-137C 820-193C 826-255C 826-215C 826-216C 826-356C 826-424C 826-358C 826-497C 826-503C 826-646C 826-647C 826-648C 318-586A Drawing Image Number BLADE SPACER 16 GA.06 THICK BLADE SPACER 18 GA.05 THICK BLADE SPACER 20 GA.04 THICK BLADE SPACER 24 GA.03 THICK SHIELD BRACKET WELDMENT 24RND DSHPN WMT 15C/C (8 OS) 27RND DSHPN WMT 17C/C (8 OS) CW BLADE CARRIER ASSY CCW BLADE CARRIER ASSY OUTER SHIELD RCR2596 OUTER SHIELD RCR2510 HHCS 1/2-13X1 1/4 GR5 HHCS 3/4-10X2 1/4 GR5 BLD BLT 1 1/8-12X44 W/.25KEY HHCS M8X25X20 GR8.8 NUT HEX TOP LOCK 1 1/8-12 PLT NUT HEX FLG TOP LK 3/4-10 PLT WASHER LOCK SPRING 1/2 PLT WASHER FLAT 1" HARDENED WASHER SPRING LOCK M8 PLT WASHER FLAT M8 PLT GRBOX SHAFT(1 3/4OD) PROTECTOR KNOB 3/8-16 FEMALE THD 2 3/8OD CUTTER BLADE 1/2X4X20.5 CW CUTTER BLADE 1/2X4X20 1/2 CW CUTTER BLADE 1/2X4X20.5 LL CW CUTTER BLADE 1/2 X 4 X 25 CW CUTTER BLADE 1/2X4X25 LL CW CUTTER BLADE 1/2X4X20.5 CCW CUTTER BLADE 1/2X4X20 1/2 CCW CUTTER BLADE 1/2X4X20.5 LL CCW CUTTER BLADE 1/2 X 4 X 25 CCW CUTTER BLADE 1/2X4X25 LL CCW DRVLN C4 31 38-6 QD CLTCH DRVLN C4 37 38-6 QD CLTCH DRVLN C4 37 38-21 QD CLTCH T-BOX 75-20 1:35 T-BOX 75-20 35:1 GBOX 1:50 STD. 38-6 SPL. COMER VENT #8.6.7.00269 COMER VENT 8.6.7.00161 3/8MNPT DRVLN 10F 38-6 FLXCPLR DRVLN 17F 38-6 FLXCPLR LARGE SHAFT CONE W ACCESS DOOR BLADE BOLT KIT As Required S/N 776426- As Required S/N 776426- As Required S/N 776426- As Required S/N 776426- RCR2596 RCR(M)2510 RCR2596 RCR(M)2510 RCR2596 Standard S/N 1000427+ RCR2596 Standard S/N 1000426- RCR2596 Optional RCR2510 RCRM2510 Standard RCR2510 RCRM2510 Optional RCR2596 Standard S/N 1000427+ RCR2596 Standard S/N 1000426- RCR2596 Optional RCR2510 RCRM2510 Standard RCR2510 RCRM2510 Optional RCR2596 RCR2510 RCRM2510 RCR2596 RCR2510 RCRM2510 RCR2596 RCR(M)2510 07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 15
Table of Contents Deck Components & 3-Point Hitch Applies to RCR2510, RCR2596, RCRM2510 Part Number Index Section 2: Frame 22332 16 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Table of Contents Deck Components & 3-Point Hitch Section 2: Frame Applies to RCR2510, RCR2596, RCRM2510 Part Number Index Ref. Part No. Part Description Comments Revision 6. 7. 8. 9. 10. 10. 1 1 1 1 1 1 1 1 16. 16. 17. 18. 19. 20. 2 2 2 2 2 26. 27. 28. 29. 30. 3 3 3 3 3 36. 37. 38. Dwg 22332 300-202S 300-429D 300-431D 312-602D 312-739H 312-739H81 312-739H82 312-739H83 312-738H 312-738H81 312-738H82 312-738H83 312-812D 312-816D 312-821D 312-822D 312-931D 312-815D 312-938D 312-813D 312-939D 312-814D 326-169D 312-817D 802-005C 802-064C 802-098C 802-073C 802-169C 802-368C 802-392C 802-603C 803-026C 803-168C 803-198C 803-231C 803-255C 804-007C 804-012C 804-013C 804-025C 804-029C 805-041C 805-058C 805-088C 805-090C 805-103C 805-137C 805-301C 805-485C Drawing Image Number PIN 1 1/8 OD X 7 1/8 USABLE CAT III BUSHING TUBE RD 2 1/4ODX1 5/32IDX2 5/8 SKID SHOE RCR2596 DECK WELDMENT RCR2596 DECK WELDMENT GREEN RCR2596 DECK WELDMENT ORANGE RCR2596 DECK WELDMENT RED RCR2510 DECK WELDMENT RCR2510 DECK WELDMENT GREEN RCR2510 DECK WELDMENT ORANGE RCR2510 DECK WELDMENT RED ACCESS COVER PLATE REAR BRACE STRAIGHT SHORT BUSHING 1 1/4ODX1 1/32IDX2LG REAR BRACE SHORT REAR BRACE STRAIGHT LONG REAR BRACE STRAIGHT LONG A-FRAME RH. A-FRAME HITCH RH. A-FRAME LH. A-FRAME HITCH LH. REAR BRACE FORMED REAR BRACE FORMED HHCS 1/4-20X1 GR5 HHCS 3/4-10X2 GR5 HHCS 1-8X4 1/2 GR5 HHCS 1-8X4 GR5 HHCS 1-8X3 1/2 GR5 HHCS 1-8X3 GR5 HHCS 3/4-10X1 3/4 GR5 PLOW 3/8-16X1 GR5 NUT LOCK 3/4-10 PLT NUT HEX TOP LOCK 1-8 PLT NUT HEX WHIZ 3/8-16 PLT NUT WING 3/8-16 PLT NUT HEX NYLOCK 1/4-20 WASHER FLAT 1/4 SAE PLT WASHER FLAT 3/8 SAE PLT WASHER LOCK SPRING 3/8 PLT WASHER FLAT 3/4 SAE PLT WASHER FLAT 1 SAE PIN ROLL 1/4X1 3/4 PIN COTTER 3/16 X 2 PIN, HAIR COTTER 3/16 WIRE DIA PIN CLEVIS 1 X 3 3/16 LG PIN LINCH 7/16 X 1 3/4 PIN CLEVIS 1 X 2 PLT PIN 1 1/8 OD X 7 1/8 USABLE PIN, HITCH 3PT CAT 1&2 RCR2596 RCR2510 RCRM2510 RCR2596 S/N 627646- RCR2510 S/N 627808- RCR2596 RCR(M)3596 RCR2510 RCR(M)2510 RCR2596 RCR2510 RCRM2596 RCR2596 RCR2510 RCRM2596 RCR2596 RCR2510 RCRM2596 (S/N 495422+ RCR2596) (S/N 495351+ RCR(M)2510) S/N 567029+ S/N 567028- RCR2596 S/N 627646- RCR2510 S/N 627808- (S/N 495422+ RCR2596) (S/N 495351+ RCR(M)2510) (S/N 495422+ RCR2596) (S/N 495351+ RCR(M)2510) RCR2596 S/N 627646- RCR2510 S/N 627808- RCR2596 S/N 627646- RCR2510 S/N 627808- S/N 983493+ RCR2596 S/N 983492- S/N 983493+ 07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 17
Deck Components & 3-Point Hitch (continued) Section 2: Frame Applies to RCR2510, RCR2596, RCRM2510 Ref. 38. 39. 40. 4 4 4 4 4 46. 47. 48. 49. 50. Part No. 805-274C 816-481C 840-273C 320-044D 890-352C 327-143S 802-010C 802-138C 803-177C 804-036C 807-350C 837-062C 837-063C Part Description PIN HITCH CAT.I-II MANUAL STORAGE CONTAINER PLUG LP 3" ID RUBBER SPCR TUBE 44ODX.93IDX50LG BUSHING 1 OD X 3/4 ID X 5/8 LG DRIVELINE HOLDER W/ HARDWARE HHCS 5/16-18X1 1/4 GR5 HHCS 5/16-18X2 1/4 GR5 NUT HEX LOCK 5/16-18 FLG. WASHER FLAT 5/16 SAE PLT SPRING TORSION DRIVELINE HLDER DRIVELINE HOOK MOUNT DRIVELINE HOOK Comments S/N 983492- (S/N 495422+ RCR2596) (S/N 495351+ RCR(M)2510) RCR2596 S/N 627647+ RCR2510 S/N 627809+ S/N 908522 to 983492 S/N 945241+ S/N 945241+ S/N 945241+ S/N 945241+ S/N 945241+ S/N 945241+ S/N 945241+ S/N 945241+ Revision 18 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Deck Components & 3-Point Hitch (continued) Section 2: Frame Applies to RCR2510, RCR2596, RCRM2510 This Page Intentionally Left Blank 07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 19
Table of Contents Equal Angle Pull Type Driveline Applies to RCR2510, RCR2596, RCRM2510 Part Number Index Section 2: Frame 22341 20 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Table of Contents Equal Angle Pull Type Driveline Section 2: Frame Applies to RCR2510, RCR2596, RCRM2510 Part Number Index Ref. Part No. Part Description Comments Revision 6. 7. 8. 9. 10. 1 1 1 1 1 1 1 1 Dwg 22341 312-681S 312-715D 312-833D 312-999D 326-002D 800-069C 802-146C 802-260C 803-019C 803-021C 804-021C 804-022C 822-100C 826-151C 826-223C 826-220C 826-256C 826-221C Drawing Image Number BEARING FLANGE ASSY. PIPE 1/2 SCH. 40 X 4 15/16 BEARING SUPPORT BEARING FLANGE TUBE 1 OD X 11/16 LG. X 5/32w SNAP RING INT 835 HHCS 5/8-11X7 1/2 GR5 HHCS 1/2-13X7 GR5 NUT LOCK 1/2-13 PLT NUT HEX 5/8-11 PLT WASHER FLAT 5/8 SAE PLT WASHER LOCK SPRING 5/8 PLT BRG 1 3/8 B X 72MM OD W/COLLAR PTO CAT. 4 X 20.5 FIXED 540 PTO CAT. 4 X 22 FIXED 1000 PTO CAT. 4 JACK SHAFT 540 PTO J/S.W/4-PLATE SC CAT4 540 PTO CAT. 4 JACK SHAFT 1000 RCR2596 RCR2510 RCRM2510 RCR2510 RCR2596 RCRM2510 07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 21
Hydraulic Lift Table of Contents Part Number Index Section 2: Frame Applies to RCR2510, RCR2596, RCRM2510 22343 22 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Section 2: Frame Hydraulic Lift Table of Contents Part Number Index Applies to RCR2510, RCR2596, RCRM2510 Ref. Part No. Part Description Comments Revision 6. 7. 8. 9. 10. 1 1 1 1 1 Dwg 22343 312-534A 312-729D 800-117C 802-022C 802-184C 803-013C 803-026C 804-012C 805-004C 805-088C 807-023C 810-200C 810-818C 811-170C 811-394C 811-676C Drawing Image Number HYDRAULIC LIFT COMPLETE HOSE HOLDER BRACKET VENT PLUG - 9/16-18 PLATED HHCS 3/8-16X1 1/2 GR5 HHCS 3/4-10X1 1/2 GR5 NUT LOCK 3/8-16 PLT NUT TOP LOCK 3/4-10 PLT WASHER FLAT 3/8 SAE PLT PIN CLEVIS 1 X 2 3/4 USABLE LG PIN, HAIR COTTER 3/16 WIRE DIA SPRING HOSE LOOP CYL 5X8X12 ROD (TIE)1 PIN STRK CNTRL SPCRS 125 TO 50 AD 9/16MORB 9/16MJIC CP 3/4FORB MALE QD POPPET TYPE HH3/8R1 144 3/4MORB 9/16FJIC 07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 23
Pull Type Table of Contents Part Number Index Section 2: Frame Applies to RCR2510, RCR2596, RCRM2510 22335 24 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Section 2: Frame Pull Type Table of Contents Part Number Index Applies to RCR2510, RCR2596, RCRM2510 Ref. Part No. Part Description Comments Revision 6. 7. 8. 9. 10. 1 1 1 1 1 16. 17. 18. 19. 20. 2 2 2 2 2 2 2 26. Dwg 22335 300-202S 312-421H 312-516H 312-613H 312-536H 312-513H 312-549L 312-629L 312-733D 318-008H 802-074C 802-098C 802-634C 803-075C 803-168C 803-265C 804-025C 804-028C 804-029C 805-015C 805-041C 805-045C 805-083C 805-088C 805-301C 805-485C 805-274C 805-103C 891-246C 890-182C 890-118C Drawing Image Number PIN 1 1/8 OD X 7 1/8 USABLE CLEVIS WELDMENT LONG LEVEL ROD WLDMT WLDMT LEVEL ROD LONG WLDMT TONGUE LONG TONGUE WELDMENT ASSY. LEVEL ROD ASSY. LEVEL ROD TUBE 1 5/8 OD X 7/32 WL X1 LG. WLDMT. LEVEL ROD SHORT HHCS 1-8X6 1/2 GR5 HHCS 1-8X4 1/2 GR5 HHCS 1-8X2 GR5 NUT HEX JAM 7/8-9 NUT HEX TOP LOCK 1-8 PLT NUT HEX COUPLER 7/8-9 x 5 WASHER FLAT 3/4 SAE PLT WASHER FLAT 1 USS PLT WASHER FLAT 1 SAE PIN LYNCH 5/16 X 1 3/4 PIN ROLL 1/4X1 3/4 PIN COTTER 5/32 X 1 1/4 LG PIN CLEVIS 3/4 X 1 1/2 PIN, HAIR COTTER 3/16 WIRE DIA PIN 1 1/8 OD X 7 1/8 USABLE PIN, HITCH 3PT CAT 1&2 PIN HITCH CAT.I-II PIN LINCH 7/16 X 1 3/4 AG SAFETY CHAIN 6400 LB SAFETY CHAIN 10000 LB SCREW JACK 2000# 14-24 TOP-WND RCR2510 RCRM2510 RCR2510 RCRM2510 RCR2596 RCR2510 RCRM2510 RCR2596 RCR2510 RCRM2510 RCR2596 RCR2596 RCR2510 RCRM2510 RCR2510 RCRM2510 RCR2510 RCRM2510 RCR2596 S/N 983493+ RCR2510 RCRM2510 RCR2596 S/N 983493+ RCR2596 S/N 983492- RCR2596 S/N 983492- S/N 688691+ S/N 688690-07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 25
Table of Contents Pull Type Axle and Tires Applies to RCR2510, RCR2596, RCRM2510 Part Number Index Section 2: Frame 22336 26 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Table of Contents Pull Type Axle and Tires Section 2: Frame Applies to RCR2510, RCR2596, RCRM2510 Part Number Index Ref. Part No. Part Description Comments Revision 6. 7. 7. 7. 8. 9. 10. 1 1 1 1 1 16. 17. 18. 19. 20. 2 2 2 2 2 26. 27. 28. 29. 30. 3 3 3 3 3 36. 37. 37. 38. 39. 40. 4 4 4 4 4 46. 47. 48. 49. 50. 5 Dwg 22336 200-001D 312-515H 312-516H 312-613H 312-549L 312-629L 312-712D 312-804D 312-805H 312-511H 312-475H 318-008H 800-001C 802-065C 802-099C 802-104C 802-326C 802-360C 802-368C 803-019C 803-026C 803-029C 803-075C 803-168C 803-265C 804-015C 804-016C 804-024C 804-029C 804-055C 805-016C 805-045C 805-083C 805-088C 805-090C 805-104C 805-187C 807-143C 814-059C 814-066C 814-263C 814-447C 814-266C 814-267C 814-268C 815-093C 815-108C 815-230C 816-098C 822-091C 822-092C 802-326C 803-308C 890-177C 312-902A 815-236C Drawing Image Number HUB GREASE CAP SPRING SHOCK WLDMT LONG LEVEL ROD WLDMT WLDMT LEVEL ROD LONG ASSY. LEVEL ROD ASSY. LEVEL ROD TUBE 1 OD X 12 GA X 15/16 LG. SPRING SHOCK SUPPORT AXLE WELDMENT RPBY 312-902A AXLE WELDMENT WLDMT. LEVEL ROD SHORT GREASE ZERK STRAIGHT 1/4-28 HHCS 3/4-10X2 1/4 GR5 HHCS 1/2-13X3 1/4 GR5 BOLT WHEEL 1/2-20X1 90-DEG HHCS 1/2-20X1 1/4 GR5 HHCS 3/4-10X6 1/2 GR5 HHCS 1-8X3 GR5 NUT LOCK 1/2-13 PLT NUT LOCK 3/4-10 PLT NUT HEX SLOTTED 7/8-14 PLT NUT HEX JAM 7/8-9 NUT HEX TOP LOCK 1-8 PLT NUT HEX COUPLER 7/8-9 x 5 WASHER LOCK SPRING 1/2 PLT WASHER FLAT 1/2 SAE PLT WASHER FLAT 3/4 USS PLT WASHER FLAT 1 SAE WASHER SPINDLE - 7/8 PIN COTTER 3/16 X 1 1/4 PLT PIN COTTER 5/32 X 1 1/4 LG PIN CLEVIS 3/4 X 1 1/2 PIN, HAIR COTTER 3/16 WIRE DIA PIN CLEVIS 1 X 3 3/16 LG PIN COTTER 3/16 X 1 1/2 PLT PIN CLEVIS 1 X 2 1/4 GR5 PLT SPRING COMP 88OD x.362w TIRE & WHEEL LAM. 6X9X21(TALL) WHEEL 15 X 5 X 4 BOLT AC TIRE 24 X 7.7 2PC AC TIRE 24X7.7 RECAP 12-20 PLY TIRE 24X7.7-10 (814-263C) RIM 2PC.4BLT 10X6 BLK(814-263C TUBE FOR 24X7.7-10 (814-263C) HUB 4 BOLT WHL W/CUPS & ZERK SPINDLE - SINGLE AXLE BOLT ON HUB 4 BLT W/CUPS, ZERK & STUDS SEAL 1 3/8 ID X 441 OD X.313 BRG 25ID CONE 15123 BRG CUP 44OD 15245 HHCS 1/2-20X1 1/4 GR5 NUT HEX FLG/LK 1/2-20 PLT.GR.G RATCHET JACK - HEAVY DUT RCR(M)3510 AXLE UPDATE KIT HUB 4 BOLT COMPLETE RCR(M)2510 RCR2596 RCR(M)2510 RCR2596 S/N 627809+ RCR(M)2510 S/N 627808- RCR(M)2510 RCR2596 (Weld in Spindle) S/N 627809+ RCR(M)2510 S/N 627809+ RCR(M)2510 S/N + S/N - S/N 627809+ RCR(M)2510 For S/N 627808- RCR(M)2510 W/ Bolt in Spindle 07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 27
Guarding Chain Table of Contents Part Number Index Section 3: Guards Applies to RCR2596 22338 28 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Section 3: Guards Guarding Chain Table of Contents Part Number Index Applies to RCR2596 Ref. Part No. Part Description Comments Revision 6. 6. 7. 8. 9. 10. 1 1 1 1 Dwg 22338 312-616A 312-775A 312-777K 312-778K 312-940D 312-942D 318-478D 312-943D 326-126D 326-127D 802-183C 802-214C 803-037C 890-341C 890-400C Drawing Image Number 96" REAR CHAIN COMPLETE 96" FRONT CHAIN COMPLETE FRONT CHAIN GUARD ASSY. RH FRONT CHAIN GUARD ASSY. LH REAR CHAINGUARD BRACKET RPBY 318-478D ROUND ROD.25 X 59 ROD 1/4 X 51 96 FRONT CHAIN GUARD RH 96 FRONT CHAIN GUARD LH RHSNB 1/2-13X1 GR5 RHSNB 1/2-13X1 1/4 GR5 NUT HEX WHIZ 1/2-13 PLT CHAIN WELD 5/16 PROOF X 5 LINK CHAIN WELD 5/16 PROOF X 4 LINK 07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 29
Guarding Chain Table of Contents Part Number Index Section 3: Guards Applies to RCR2510, RCRM2510 22340 30 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Section 3: Guards Guarding Chain Table of Contents Part Number Index Applies to RCR2510, RCRM2510 Ref. Part No. Part Description Comments Revision 6. 7. 8. 9. 10. 1 1 1 1 1 Dwg 22340 312-503A 312-751A 312-754K 312-755K 312-758K 312-823D 312-826D 312-827D 326-097D 326-098D 326-099D 802-183C 803-037C 890-341C 890-400C Drawing Image Number 3510 REAR CHAIN COMPLETE 2510 FRONT CHAIN COMPLETE ASSY. FRONT OUTER LH. CHNGRD. ASSY. FRONT OUTER RH. CHNGRD. ASSY. FRONT CENTER CHAINGUARD FRT. CHAINGUARD BRACKET CTR. ROD 1/4 X 63 REAR CHAINGUARD BRACKET FRONT CHAINGUARD BRACKET RH FRONT CHAINGUARD BRACKET LH ROUND ROD 1/4 X 32 RHSNB 1/2-13X1 GR5 NUT HEX WHIZ 1/2-13 PLT CHAIN WELD 5/16 PROOF X 5 LINK CHAIN WELD 5/16 PROOF X 4 LINK 07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 31
Guarding Rubber Table of Contents Part Number Index Section 3: Guards Applies to RCR2596 22337 32 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Table of Contents Guarding Rubber Section 3: Guards Applies to RCR2596 Part Number Index Ref. Part No. Part Description Comments Revision 6. 7. 8. 9. 10. 1 1 1 Dwg 22337 312-618A 312-774A 312-776K 312-936D 326-123D 326-124D 802-106C 802-155C 802-214C 803-037C 803-198C 816-299C 816-397C Drawing Image Number 96" REAR RUBBER COMPLETE 96" FRONT RUBBER COMPLETE FRONT RUBBER DEFLECTOR ASSY. DEFLECTOR STRAP FRONT DEFLECTOR BRACKET DEFLECTOR STRAP RHSNB 1/2-13X1 1/2 GR5 RHSNB 3/8-16X1 1/4 GR5 RHSNB 1/2-13X1 1/4 GR5 NUT HEX WHIZ 1/2-13 PLT NUT HEX WHIZ 3/8-16 PLT REAR RUBBER DEFLECTOR FRONT RUBBER DEFLECTOR Left Hand or Right Hand 07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 33
Guarding Rubber Table of Contents Part Number Index Section 3: Guards Applies to RCR2510, RCRM2510 22339 34 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Table of Contents Guarding Rubber Section 3: Guards Applies to RCR2510, RCRM2510 Part Number Index Ref. Part No. Part Description Comments Revision 6. 7. 8. 9. 10. 1 1 1 1 1 16. 17. 18. 19. Dwg 22339 312-505A 312-752A 312-756K 312-757K 312-759K 312-830D 312-834D 312-836D 326-088D 326-089D 326-095D 802-106C 802-155C 802-214C 803-037C 803-198C 816-272C 816-274C 816-384C Drawing Image Number 3510 REAR RUBBER COMPLETE 2510 FRONT RUBBER COMPLETE ASSY. FRT. OUTER RH DEFLECTOR ASSY. FRT. OUTER LH DEFLECTOR ASSY. FRONT CENTER DEFLECTOR FRT. DEFLECTOR BRACKET CTR. FRT.CTR.DEFLECTOR STRAP REAR DEFLECTOR STRAP FRONT DEFLECTOR BRACKET LH FRONT DEFLECTOR BRACKET RH DEFLECTOR STRAP RHSNB 1/2-13X1 1/2 GR5 RHSNB 3/8-16X1 1/4 GR5 RHSNB 1/2-13X1 1/4 GR5 NUT HEX WHIZ 1/2-13 PLT NUT HEX WHIZ 3/8-16 PLT FRT. CTR. RUBBER DEFLECTOR REAR RUBBER DEFLECTOR FRT OUTER RUBBER DEFLECTOR Includes 1 Ea #3,4 & 5 07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 35
Coupler Intermediate 826-646c & 826-647c Section 4: Drivelines Applies to RCR2510, RCR2596, RCRM2510 30118 36 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Coupler Intermediate 826-646c & 826-647c Section 4: Drivelines Applies to RCR2510, RCR2596, RCRM2510 Ref. Part No. Part Description Comments Revision 6. 7. 8. 9. 10. 1 Dwg 30118 826-646C 826-647C 07-013 09-014 10-038 16-300 16-301 19-579 19-075 23-028 23-071 802-079C 802-891C 803-012C 803-282C Drawing Image Number CPLR, 75-20X38-6X10.31 FLE CPLR, 75-20X38-6X16.56 FLE * WASHER, FLEX COUPLER SHAPED ZERK, M8X1 GREASE BUSHING, 16MM ID COUPLER WLDMNT, DOUBLE FLEX YOKE WLDMNT, DOUBLE FLEX YOKE DISK, FLEX COUPLER RUBBER RPBY 19-579 YOKE, 75-20 FLEX CONNECTOR YOKE, 375-6 FLEX CONNECTOR HHCS 3/8-16X1 1/4 GR5 HHCS M16X0X65 GR8.8 NUT HEX JAM 3/8-16 PLT NUT HEX NYLOCK M16X00 GRB PT RCR2596 RCR(M)2510 For 826-646C RCR2596 For 826-647C RCR2510 S/N + S/N - 07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 37
Driveline 1000 RPM (826-216C) Eurocardan Section 4: Drivelines Applies to RCRM2510 22283 38 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Driveline 1000 RPM (826-216C) Eurocardan Section 4: Drivelines Applies to RCRM2510 Ref. Part No. Part Description Comments Revision 6. 7. 8. 9. 10. 10. 1 1 1 1 1 16. 17. 18. 19. 20. 2 2 2 2 2 26. 27. dwg22283 826-216C 1786711 1215733 1885702 1215735 1885709 1877067 1876067 1885703 1786710 1406116 1406016 1006020 1706029 1526077 6331070 1528077 6331080 1706027 1016015 818-540C 818-552C 044321 6560508 1004220 6560006 1016017 1004225 826-566C Drawing Image Number PTO STD.W/2-PLATE SC CAT4 1000 EC TUBE BEARING (INNER TUBE) EC STIFFENING RING EC SHORT CONE EC STOP RING EC SAFETY SLEEVE EC INNER TUBE SHEILD EC OUTER TUBE SHEILD EC STANDARD CONE EC TUBE BEARING (OUTER TUBE) EC CLUTCH FD2/6 1 3/4" Z20 RPBY 1406116 EC CROSS ASSEMBLY EC INNER TUBE YOKE EC INNER TUBE 770MM EC 10X70 ROLL PIN EC OUTER TUBE 770MM EC 10X80-DIN-1481 O/TUBE R/PIN EC OUTER TUBE YOKE EC YOKE ASSEMBLY (TRACT. END) DECAL DANGER GUARD MISS PTO DECAL DANGER PTO DRIVELINE DRIVELINE SHIELD SAFETY CHAIN EC GREASE ZERK 8X1 45 DEG. EC TWIST COLLAR KIT (TRT. END) EC GREASE ZERK M6X1 STRAIGHT EC YOKE ASSEMBLY (TRACTOR END) EC PULL COLLAR KIT SHIELD KIT, 826-215C &826-216C S/N 928934-07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 39
Driveline 1000 RPM (826-221C) Eurocardan Section 4: Drivelines Applies to RCRM2510 16173 40 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Driveline 1000 RPM (826-221C) Eurocardan Section 4: Drivelines Applies to RCRM2510 Ref. Part No. Part Description Comments Revision 6. 6. 7. 8. 8. 9. 10. 1 1 1 1 1 1 16. 16. 17. 18. 19. 20. 2 dwg16173 826-221C 1786711 1215733 1885702 1215735 1885709 1877907 1877079 044321 1876904 1876079 1885705 1786710 1896901N327 1896084N327 6331070 1526085 1706029 1006020 1406128 1406028 818-552C 818-540C 6560508 6561306 826-567C Drawing Image Number PTO CAT. 4 JACK SHAFT 1000 EC TUBE BEARING (INNER TUBE) EC STIFFENING RING EC SHORT CONE EC STOP RING EC SAFETY SLEEVE EC INNER TUBE SHIELD EC INNER TUBE (1877094) 790MM DRIVELINE SHIELD SAFETY CHAIN EC OUTER TUBE SHIELD EC OUTER TUBE (1876094) 790MM EC EXTRA SHORT CONE (FOR MX) EC TUBE BEARING (OUTER TUBE) EC OUTER TUBE ASSEMBLY EC OUTER TUBE ASSY EC 10X70 ROLL PIN EC INNER TUBE (1526084) 840MM EC INNER TUBE YOKE EC CROSS ASSEMBLY EC TORQUE LIMITER, (FD 2) RPBY 1406128 DECAL DANGER PTO DRIVELINE DECAL DANGER GUARD MISS PTO EC GREASE ZERK 8X1 45 DEG. EC GREASE ZERK M6X1 EXTRA SHRT SHIELD KIT, 826-220C &826-221C S/N + S/N - S/N 928934- S/N + S/N - S/N + S/N - 07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 41
Driveline 1000 RPM (826-223C) Eurocardan Section 4: Drivelines Applies to RCRM2510 16370 42 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Driveline 1000 RPM (826-223C) Eurocardan Section 4: Drivelines Applies to RCRM2510 Ref. Part No. Part Description Comments Revision 6. 7. 8. 9. 10. 1 1 1 1 1 16. 17. 18. 19. 20. 2 2 dwg16370 826-223C 1786710 1215733 1885704 1215735 1885709 1876034D 1885703 1116010 1006020 1706027 1528044D 6331080 1016015 818-540C 818-552C 044321 6560508 1004220 1004224 826-568C 1016013 1004227 Drawing Image Number PTO CAT. 4 X 22 FIXED 1000 EC TUBE BEARING (OUTER TUBE) EC STIFFENING RING EC LONG CONE EC STOP RING EC SAFETY SLEEVE EC OUTER TUBE 340MM EC STANDARD CONE EC YOKE ASSY 1 3/8-6(IMP. END) EC CROSS ASSEMBLY EC OUTER TUBE YOKE EC OUTER TUBE EC 10X80-DIN-1481 O/TUBE R/PIN EC YOKE ASSEMBLY (TRACT. END) DECAL DANGER GUARD MISS PTO DECAL DANGER PTO DRIVELINE DRIVELINE SHIELD SAFETY CHAIN EC GREASE ZERK 8X1 45 DEG. EC TWIST COLLAR KIT (TRT. END) EC TWIST COLLAR KIT (IMP. END) SHIELD KIT, 826-223C EC YOKE ASSEMBLY EC PULL COLLAR KIT EVOLUTION S/N 928934-07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 43
Driveline 1000 RPM (826-226C) Eurocardan Section 4: Drivelines Applies to RCRM2510 15995 44 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Driveline 1000 RPM (826-226C) Eurocardan Section 4: Drivelines Applies to RCRM2510 Ref. Part No. Part Description Comments Revision 6. 7. 8. 9. 9. 10. 1 1 1 1 1 1 16. dwg15995 826-226C 1786710 1215733 1885702 1215735 1885709 044321 1876025D 1885705 1896030S821 1896030D821 6331080 1706027 1006020 1406116 1406016 818-552C 818-540C 6560508 Drawing Image Number PTO W/STUB SHAFT/SC 1000 1 3/4 EC TUBE BEARING (OUTER TUBE) EC STIFFENING RING EC SHORT CONE EC STOP RING EC SAFETY SLEEVE DRIVELINE SHIELD SAFETY CHAIN EC OUTER TUBE SHEILD EC EXTRA SHORT CONE (FOR MX) EC OUTER TUBE ASSY (HRDND) EC OUTER TUBE ASSY EC 10X80-DIN-1481 O/TUBE R/PIN EC OUTER TUBE YOKE EC CROSS ASSEMBLY EC CLUTCH FD2/6 1 3/4" Z20 RPBY 1406116 DECAL DANGER PTO DRIVELINE DECAL DANGER GUARD MISS PTO EC GREASE ZERK 8X1 45 DEG. S/N 928934- Rev. 2 Rev. 1 07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 45
Driveline 540 RPM (826-151C) Eurocardan Section 4: Drivelines Applies to RCR2510, RCR2596 16610 46 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Driveline 540 RPM (826-151C) Eurocardan Section 4: Drivelines Applies to RCR2510, RCR2596 Ref. Part No. Part Description Comments Revision 6. 7. 8. 9. 10. 1 1 1 1 1 16. 17. 18. Dwg 16610 826-151C 1786710 1215733 1885704 1215735 1885709 1876030D 1885703 1006020 1706027 6331080 1528040D 818-540C 818-552C 044321 6560508 1016013 1004227 826-578C Drawing Image Number PTO CAT. 4 X 20.5 FIXED 540 EC TUBE BEARING (OUTER TUBE) EC STIFFENING RING EC LONG CONE EC STOP RING EC SAFETY SLEEVE EC OUTER TUBE SHIELD EC STANDARD CONE EC CROSS ASSEMBLY EC OUTER TUBE YOKE EC 10X80-DIN-1481 O/TUBE R/PIN EC OUTER TUBE DECAL DANGER GUARD MISS PTO DECAL DANGER PTO DRIVELINE DRIVELINE SHIELD SAFETY CHAIN EC GREASE ZERK 8X1 45 DEG. EC YOKE ASSEMBLY EC PULL COLLAR KIT EVOLUTION SHIELD KIT, 826-151C S/N 928934-07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 47
Driveline 540 RPM (826-215C) Eurocardan Section 4: Drivelines Applies to RCR2510 22283 48 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Driveline 540 RPM (826-215C) Eurocardan Section 4: Drivelines Applies to RCR2510 Ref. Part No. Part Description Comments Revision 6. 7. 8. 9. 10. 1 1 1 1 1 16. 17. 18. 19. 20. 2 2 2 2 2 26. 27. Dwg 22283 826-215C 1786711 1215733 1885702 1215735 1885709 1877067 1876067 1885703 1786710 1446016 1006020 1706029 1526077 6331070 1528077 6331080 1706027 1016015 818-540C 818-552C 044321 6560508 1004220 6560006 1016013 1004225 826-566C Drawing Image Number PTO STD.W/4-PLATE SC CAT4 540 * EC TUBE BEARING (INNER TUBE) EC STIFFENING RING EC SHORT CONE EC STOP RING EC SAFETY SLEEVE EC INNER TUBE SHEILD EC OUTER TUBE SHEILD EC STANDARD CONE EC TUBE BEARING (OUTER TUBE) EC CLUTCH FD4/6 1 3/4 20 SPL EC CROSS ASSEMBLY EC INNER TUBE YOKE EC INNER TUBE 770MM EC 10X70 ROLL PIN EC OUTER TUBE 770MM EC 10X80-DIN-1481 O/TUBE R/PIN EC OUTER TUBE YOKE EC YOKE ASSEMBLY (TRACT. END) DECAL DANGER GUARD MISS PTO DECAL DANGER PTO DRIVELINE DRIVELINE SHIELD SAFETY CHAIN EC GREASE ZERK 8X1 45 DEG. EC TWIST COLLAR KIT (TRT. END) EC GREASE ZERK M6X1 STRAIGHT EC YOKE ASSEMBLY (TRACTOR END) EC PULL COLLAR KIT SHIELD KIT, 826-215C &826-216C S/N 928934-07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 49
Driveline 540 RPM (826-220C) Eurocardan Section 4: Drivelines Applies to RCR2510 16173 50 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Driveline 540 RPM (826-220C) Eurocardan Section 4: Drivelines Applies to RCR2510 Ref. Part No. Part Description Comments Revision 6. 6. 7. 8. 8. 9. 10. 1 1 1 1 1 1 16. 16. 17. 18. 19. 20. 2 Dwg 16173 826-220C 1786711 1215733 1885702 1215735 1885709 1877907 1877079 044321 1876904 1876079 1885705 1786710 1896901N327 1896084N327 6331070 1526085 1706029 1006020 1446137 1446037 818-552C 818-540C 6560508 6561306 826-567C Drawing Image Number PTO CAT. 4 JACK SHAFT 540 EC TUBE BEARING (INNER TUBE) EC STIFFENING RING EC SHORT CONE EC STOP RING EC SAFETY SLEEVE EC INNER TUBE SHIELD EC INNER TUBE SHEILD DRIVELINE SHIELD SAFETY CHAIN EC OUTER TUBE SHIELD EC OUTER TUBE SHEILD EC EXTRA SHORT CONE (FOR MX) EC TUBE BEARING (OUTER TUBE) EC OUTER TUBE ASSEMBLY EC OUTER TUBE ASSY EC 10X70 ROLL PIN EC INNER TUBE (1526084) 840MM EC INNER TUBE YOKE EC CROSS ASSEMBLY EC TORQUE LIMITER, (FD 4) RPBY 1446137 DECAL DANGER PTO DRIVELINE DECAL DANGER GUARD MISS PTO EC GREASE ZERK 8X1 45 DEG. EC GREASE ZERK M6X1 EXTRA SHRT SHIELD KIT, 826-220C &826-221C S/N 661228+ S/N 661227- S/N 928934- S/N 661228+ S/N 661227- S/N 661228+ S/N 661227- S/N 661228+ S/N 661227- S/N 661228+ 07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 51
Driveline 540 RPM (826-255C) Eurocardan Section 4: Drivelines Applies to RCR2510, RCR2596 22283 52 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Driveline 540 RPM (826-255C) Eurocardan Section 4: Drivelines Applies to RCR2510, RCR2596 Ref. Part No. Part Description Comments Revision 6. 7. 8. 9. 10. 1 1 1 1 1 16. 17. 18. 19. 20. 2 2 2 2 2 26. 27. Dwg 22283 826-255C 1786711 1215733 1885702 1215735 1885709 1877052 1876052 1885703 1786710 1446016 1006020 1706029 1526062 6331070 1528084 6331080 1706027 1016012 818-540C 818-552C 044321 6560508 1004220 6560006 1016013 1004225 826-569C Drawing Image Number PTO STD.W/4-PLATE SC CAT4 540 EC TUBE BEARING (INNER TUBE) EC STIFFENING RING EC SHORT CONE EC STOP RING EC SAFETY SLEEVE EC INNER TUBE SHEILD EC OUTER TUBE SHEILD EC STANDARD CONE EC TUBE BEARING (OUTER TUBE) EC CLUTCH FD4/6 1 3/4 20 SPL EC CROSS ASSEMBLY EC INNER TUBE YOKE EC INNER TUBE (1526084) 620MM EC 10X70 ROLL PIN EC 840MM OUT. STOCK LENGTH TB. EC 10X80-DIN-1481 O/TUBE R/PIN EC OUTER TUBE YOKE YOKE ASSEMBLY PULL TYPE DECAL DANGER GUARD MISS PTO DECAL DANGER PTO DRIVELINE DRIVELINE SHIELD SAFETY CHAIN EC GREASE ZERK 8X1 45 DEG. EC TWIST COLLAR KIT (TRT. END) EC GREASE ZERK M6X1 STRAIGHT EC YOKE ASSEMBLY EC PULL COLLAR KIT SHIELD KIT, 826-255C &826-258C S/N 928934- Shown 07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 53
Driveline 540 RPM (826-256C) Eurocardan Section 4: Drivelines Applies to RCR2596 16173 54 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Driveline 540 RPM (826-256C) Eurocardan Section 4: Drivelines Applies to RCR2596 Ref. Part No. Part Description Comments Revision 6. 6. 7. 8. 8. 9. 10. 1 1 1 1 1 1 16. 16. 17. 18. 19. 20. 2 Dwg 16173 826-256C 1786711 1215733 1885702 1215735 1885709 1877304 1877064 044321 1876304 1876064 1885705 1786710 1896314N327 1896069N327 6331070 1526070 1706029 1006020 1446137 1446037 818-552C 818-540C 6560508 6561306 826-570C Drawing Image Number PTO J/S.W/4-PLATE SC CAT4 540 EC TUBE BEARING (INNER TUBE) EC STIFFENING RING EC SHORT CONE EC STOP RING EC SAFETY SLEEVE EC INNER TUBE SHIELD RPBY 1877304 DRIVELINE SHIELD SAFETY CHAIN EC OUTER TUBE SHIELD RPBY 1876304 EC EXTRA SHORT CONE (FOR MX) EC TUBE BEARING (OUTER TUBE) EC OUTER TUBE ASSEMBLY RPBY 1896314N327 EC 10X70 ROLL PIN EC INNER TUBE (1526084) 840MM EC INNER TUBE YOKE EC CROSS ASSEMBLY EC TORQUE LIMITER, (FD 4) RPBY 1446137 DECAL DANGER PTO DRIVELINE DECAL DANGER GUARD MISS PTO EC GREASE ZERK 8X1 45 DEG. EC GREASE ZERK M6X1 EXTRA SHRT SHIELD KIT, 826-256C S/N 670486+ S/N 670485- S/N 928934- S/N 670486+ S/N 670485- S/N 670486+ S/N 670485- S/N 670486+ 07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 55
Driveline CV 1000 RPM (826-063C) Walterscheid Section 4: Drivelines Applies to RCRM2510 10452 56 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Driveline CV 1000 RPM (826-063C) Walterscheid Section 4: Drivelines Applies to RCRM2510 Ref. Part No. Part Description Comments Revision 6. 7. 8. 9. 10. 1 1 1 1 1 16. 17. 18. 19. 20. 2 2 2 2 2 26. 27. 28. Dwg 10452 826-063C 320684 020469 30008 010490 695581 020672 365722 342221 019519 020617 383084 321245 134713 383334 377341 365305 087276 044321 384064 383333 388434 172758 312410 355155 386083 380371 390404 826-589C 359471 Drawing Image Number PTO CV 2400 X 60 1000 RPM * WS YOKE 1 3/8-21 SPL WS BOLT M12 X 75 COSMO SELF LOCK NUT M12 RPBY 30008 WS YOKE 1 3/8-21 ASGE WS GREASE ZERK WS DOUBLE YOKE WS CROSS & BEARING KIT WS INBOARD YOKE WS SPRING PIN 10 X 20 WS PROFILE & SLEEVE WS INNER PROFILE 16 GA WS INBOARD YOKE 1B WALTERSCHEID DNGR DECAL-STEEL WS SHIELD CONE 11 RIB WALTERSCHEID SCREW WS BEARING RING - SC25 WALTERSCHEID SAFETY CHAIN WS INNER SHIELD TUBE-ROUND WALTERSCHEID DANGER DECAL-SHLD WS OUTER SHIELD TUBE OVL WS SHIELD CONE 3 RIB WS CROSS BEARING KIT WS SUPPORT BEARING WS CV CONE & BEARING ASSY WS ZERK WS ASGE COLLAR KIT SHIELD KIT, 826-063C WS REINFORCING COLLAR Obsolete S/N 928934-07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 57
Driveline CV Pull Type Cutter 540 RPM (826-053C) Walterscheid Section 4: Drivelines Applies to RCR2510 30279 58 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Driveline CV Pull Type Cutter 540 RPM (826-053C) Walterscheid Section 4: Drivelines Applies to RCR2510 Ref. Part No. Part Description Comments Revision 6. 7. 8. 9. 10. 1 1 1 1 1 16. 17. 18. 19. 20. 2 2 2 2 2 26. 27. 28. Dwg 30279 826-053C 320684 020469 30008 010490 695580 020672 365722 342221 019519 020616 382647 095758 134713 818-540C 377341 365305 087276 044321 382437 383333 383128 172758 312410 355155 386083 380371 381908 826-590C 359471 Drawing Image Number PTO CV 2400 X 60 540 RPM * WS YOKE 1 3/8-21 SPL WS BOLT M12 X 75 COSMO SELF LOCK NUT M12 RPBY 30008 WS YOKE 1 3/8-6 ASGE WS GREASE ZERK WS DOUBLE YOKE WS CROSS & BEARING KIT WS INBOARD YOKE WS SPRING PIN 10 X 75 WS PROFILE & SLEEVE WS INNER PROFILE 16 GA WS INBOARD YOKE 1B DECAL DANGER GUARD MISS PTO WS SHIELD CONE 11 RIB WALTERSCHEID SCREW WS BEARING RING - SC25 WALTERSCHEID SAFETY CHAIN WS INNER SHIELD TUBE ROUND WALTERSCHEID DANGER DECAL-SHLD WS OUTER SHIELD TUBE OVL. WS SHIELD CONE 3 RIB WS CROSS BEARING KIT WS SUPPORT BEARING WS CV CONE & BEARING ASSY WS ZERK WS QUICK DISCONNECT KIT SHIELD KIT, 826-053C WS REINFORCING COLLAR Obsolete S/N 928934-07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 59
Driveline Flex Coupler (826-359C) Eurocardan Section 4: Drivelines Applies to RCR2510, RCRM2510 22345 60 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Driveline Flex Coupler (826-359C) Eurocardan Section 4: Drivelines Applies to RCR2510, RCRM2510 Ref. Part No. Part Description Comments Revision 6. 7. 8. 9. 10. 1 1 1 Dwg 22345 826-359C 1705267 1235287 1785273 6410716 1005240 1706224 6141660 1535275 6412016 6821484 1006020 6560006 312-600A Drawing Image Number FLEX CPLR 75-20 TO 38-6 EC CONNECTION HUB EC WSH. BD. 35mm O.D/16.5mm I.D EC RUBBER DISC EC NUT EC FLANGE WELDMENT EC YOKE 1 3/8 Z6 INDUCT. HARD EC BOLT EC BOLT BUSHING EC WASHER 29.8mm O.D/17.2mm I.D CONICAL DOG KIT EC CROSS ASSEMBLY EC GREASE ZERK M6X1 STRAIGHT FLEX COUPLER KIT (ONE DISC) 07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 61
Driveline Flex Coupler (826-360C) Eurocardan Section 4: Drivelines Applies to RCR2596 22350 62 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Driveline Flex Coupler (826-360C) Eurocardan Section 4: Drivelines Applies to RCR2596 Ref. Part No. Part Description Comments Revision 6. 7. 8. 9. 10. 1 Dwg 22350 826-360C 6141660 1705267 1235287 1535275 1785273 6412016 6410716 1005241 6560208 312-600A 6821484 Drawing Image Number FLEX CPLR 75-20 TO 38-6 * EC BOLT EC CONNECTION HUB EC WSH. BD. 35mm O.D/16.5mm I.D EC BOLT BUSHING EC RUBBER DISC EC WASHER 29.8mm O.D/17.2mm I.D EC NUT EC SPIDER TUBE EC GREASE ZERK M8 STRAIGHT FLEX COUPLER KIT (ONE DISC) CONICAL DOG KIT 07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 63
Driveline Slip Clutch (1406016) Eurocardan Section 4: Drivelines Applies to RCRM2510 15523 64 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Driveline Slip Clutch (1406016) Eurocardan Section 4: Drivelines Applies to RCRM2510 Ref. Part No. Part Description Comments Revision 6. 7. 8. 9. 10. dwg15523 1406016 1215012 1706033 1705009 1808010 1708017 6821483 1138008 1138007 6691080 330-297A Drawing Image Number EC CLUTCH FD2/6 1 3/4 20 SPL RPBY 330-297A EC CLUTCH YOKE W/FLANGE EC CLUTCH BUSHING EC CLUTCH LINING RING EC HUB WITH FLANGE EC CONICAL DOG KIT REPLACEMENT EC INNER DISK EC PRESSURE DISK EC COMPLETE BOLT SV KIT, EC SLIP CLUTCH SPRING Contains 8 Springs 07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 65
Driveline Slip Clutch (1406028) Eurocarda Section 4: Drivelines Applies to RCRM2510 22375 66 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Driveline Slip Clutch (1406028) Eurocarda Section 4: Drivelines Applies to RCRM2510 Ref. Part No. Part Description Comments Revision 6. 7. 8. 9. 10. 1 dwg22375 1406028 1706033 1706314 6411010 6001085 1215012 1138007 1138008 1808010 6761480 1705009 330-297A Drawing Image Number EC TORQUE LIMITER, (FD 2) EC CLUTCH YOKE W/FLANGE FD2 HUB 1 3/4 WITH FLANGE REP BY 803-279C EC BOLT (M10X85) RPBY 330-297A EC PRESSURE DISK EC INNER DISK EC CLUTCH LINING RING EC BOLT EC CLUTCH BUSHING SV KIT, EC SLIP CLUTCH SPRING 07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 67
Table of Contents Driveline Slip Clutch (1406128) EC Applies to RCRM2510 Part Number Index Section 4: Drivelines 30197 68 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Table of Contents Driveline Slip Clutch (1406128) EC Section 4: Drivelines Applies to RCRM2510 Part Number Index Ref. Part No. Part Description Comments Revision 6. 7. 8. 9. 10. Dwg 30197 1406128 1706033 1706314 803-279C 6001085 1215010 1138007 1138008 1808010 6761480 1705009 Drawing Image Number EC TORQUE LIMITER, (FD 2) * EC CLUTCH YOKE W/FLANGE FD2 HUB 1 3/4 WITH FLANGE NUT HEX M10X5 PLT EC BOLT (M10X85) EC SPRING EC PRESSURE DISK EC INNER DISK EC CLUTCH LINING RING EC BOLT, NUT & WASHER KIT EC CLUTCH BUSHING 07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 69
Driveline Slip Clutch (1446016) Eurocardan Section 4: Drivelines Applies to RCR2510, RCR2596 15521 70 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Driveline Slip Clutch (1446016) Eurocardan Section 4: Drivelines Applies to RCR2510, RCR2596 Ref. Part No. Part Description Comments Revision 6. 7. 8. 9. 10. 1 Dwg 15521 1446016 1215012 1706033 1705009 1808010 1708034 1138008 1708016 6821483 1138007 6691010 330-297A Drawing Image Number EC CLUTCH FD4/6 1 3/4 20 SPL * RPBY 330-297A EC CLUTCH YOKE W/FLANGE EC CLUTCH BUSHING EC CLUTCH LINING RING EC CLUTCH MIDDLE DISK EC INNER DISK EC HUB WITH FLANGE EC CONICAL DOG KIT REPLACEMENT EC PRESSURE DISK EC BOLT & SCREW NUT KIT REPL. SV KIT, EC SLIP CLUTCH SPRING 1 3/4-20 Contains 8 Springs 07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 71
Driveline Slip Clutch (1446037) Eurocardan Section 4: Drivelines Applies to RCR2510, RCR2596 16561 72 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 07/14/17
Driveline Slip Clutch (1446037) Eurocardan Section 4: Drivelines Applies to RCR2510, RCR2596 Ref. Part No. Part Description Comments Revision 6. 7. 8. 9. 10. 1 1 1 1 Dwg 16561 1446037 803-279C 1215012 1706033 1705009 1808010 1708034 1138008 1706313 6141480 6410114 6412114 1138007 6001010 330-297A Drawing Image Number EC CLUTCH FD4/6 1 3/4 20 SPL NUT HEX M10X5 PLT RPBY 330-297A EC CLUTCH YOKE W/FLANGE EC CLUTCH BUSHING EC CLUTCH LINING RING EC CLUTCH MIDDLE DISK EC INNER DISK EC HUB WITH FLANGE EC BOLT (M14X80) EC SCREW NUT (M14) EC WASHER (d14) EC PRESSURE DISK EC BOLT (M10X100) SV KIT, EC SLIP CLUTCH SPRING Contains 8 Springs 07/14/17 RCR2596, RCR2510 & RCRM2510 Rotary Cutter 312-753P 73