NSR GT3 TECHNICAL RULES (version 5.0 2014) ANYTHING WHICH IT IS NOT LISTED IT MUST BE CONSIDERED FORBIDDEN 1. MODELS ALLOWED 1.1 Audi R8 GT3 Corvette C6R GT2 Porsche 997 GT3 ASV GT3 Porsche 997 GT3 Audi R8 GT3 Corvette C6R GT2 2.3 It s compulsory to apply on the windscreen the supplied sticker with the team s name 2.4 On the body there must be three number s white pods 2.5 It must be fixed to the chassis by NSR screws and the screws pod can be reinforced with non metallic stuff 2.6 At the end of the race, rear mirrors can be missing 2.7 It can t be lightened from standard 2.8 The minimum weights are: Porsche 997 17.0 grams (*** you need NSR1380 Lexan interior) Audi R8 LMS 19.0 grams (*** you need Lexan interior) Corvette C6R 21.5 grams ASV GT3 20.0 grams 2.11 The thickness of the body will be accurately measured and a foulty thickness will result in 100 laps penalty, the last position on the starting grid and an added weight of 5 gr. under the roof. 3. LIGHT SET (for endurance 24h race) 2. BODYSHELL ASV GT3 2.1 It must be standard in all its parts and can t be modified 2.2 It must be entirely painted a part from the transparent parts 3.1 It is compulsory the use of the AVANT SLOT code 10903 3.2 It is allowed to hole and/or replace the existing plastic headlights with led set 3.3 The given leds cannot be replaced with other. 3.4 The given electric wires can be replaced with other equivalent 3.5 The electric circuit can be fixed either on the chassis or on the body. In case of the latter, the minimum weight of the body (ref.2.10) must be increased by 2 grams 3.6 The lighting of the lights can be done also by a switch
3.7 At the start of the race the lights must be off and they will be turned on (switch or else) at the beginning of the night period. All through the night period there must be lightened at least three leds over four 3.8 In case of fault, this must be fixed (repaired or replaced) during the racing time of the relative heat otherwise the team will be penalized by 20 laps to which other 5 laps will be added for each heat done after the failure 3.9 At the end of the night period the light can be turned off 3.10 In any case for the entire race the lights circuit must be complete 3.11 It is forbidden adding any other light source. 5. MOTOR MOUNT DROP ARM SUSPENSION 5.1 The motor mount is the RED ref. 1237 or 1259 1237 TRIANGULAR ANGLEWINDER MOTOR SUPPORT XHARD RED 1259 NEW TRIANGULAR ANGLEWINDER MOTOR SUPPORT XHARD RED 4. CHASSIS 4.1 For each model it is allowed the use of following versions: 1401 AUDI R8 SOFT BLUE 1402 AUDI R8 MEDIUM BLACK 1403 AUDI R8 HARD WHITE 5.2 It is allowed to cut motor mount as showed in pictures to easy install and unistall motor 5.3 Only standard (any color) ref. 1231 screwed plastic taps are allowed 1397 CORVETTE C6R SOFT BLUE 1398 CORVETTE C6R MEDIUM BLACK 1399 CORVETTE C6R HARD WHITE 1393 PORSCHE 997 SOFT BLUE 1394 PORSCHE 997 MEDIUM BLACK 1395 PORSCHE 997 HARD WHITE 1445 ASV GT3 SOFT BLUE 1444 ASV GT3 MEDIUM BLACK 1446 ASV GT3 HARD WHITE medium 5.4 1234 GUIDE DROP ARM 64mm XHARD RED 5.5 It is allowed to block drop arm with screw (also adding spring) or keep free movement It is possible to add a spring 5.6 Suspension are allowed. soft Hard 1228 SOFT SUSPENSION KIT for triangular motor support 1229 MEDIUM SUSPENSION KIT for triangular motor support 1230 HARD SUSPENSION KIT for triangular motor support 4.2 It is allowed to install 4 screws for front axle regulation 4.3 It is compulsory writing the Team s name on the bottom of the chassis 1208 Complete spring set Soft Medium Hard
6. BEARINGS AND AXLES 6.1 Standard axles only ref. 4801 and 4802 6.2 Bearing ref. 4803 4846 4847 6.3 Spacers are allowed on front and rear axles 8.2 Only allowed the NSR 13t pinion, metal or plastic: Plastic pinion ref 7313 13t RED Metal pinion ref 7113 13t (brass) 7. MOTOR 7.1 Long can 17.000 rpm Baby King (light green label) already oiled handed out by Organisers WITHOUT pinion. 7.2 It can be fixed to the chassis only by screw. 9. RIMS 9.1 Front NSR standard rims ref. 5003 fixed by 4/40 allen screw 9.2 Rear NSR standard rims ref. 5004 fixed by 4/40 allen screw 8. GEARS & PINIONS 8.1 Only allowed the NSR anglewinder gear, metal or plastic: metal gears Ø 16.8mm ref. 6528, 6529, 6530, 6531, 6532, 6533, 6534 9.3 Repro NSR cover rims are compulsory, free choice and free colours (ref 5422, 5424, 5426, 5428, 5429, 5430, 5431, 5432) and they can be glued 28 29 30 31 32 33 34 5422 Ø 17 mm BBS white 5426 Ø 17 mm BBS silver 5424 Ø 17 mm BBS black plastic gears Ø 16.0mm ref. 6626, 6627, 6628, 6629, 6630, 6631, 6632, 6633 26 27 28 29 30 31 32 33 5428 12 sprokes red 5429 12 sprokes blue 5430 12 sprokes black Ø 17 mm 5431 12 sprokes white 5432 12 sprokes silver 9.4 In case of lost of one repro rims, it has to be replaced withing 3 minutes otherwise 5 laps penalty will be given.
10. FRONT TYRES 10.1 Standar recognizable NSR front tyres ref. 5201 (17x8) 5202 (19x10) 5226 (18x8) 10.2 The tyres can be glued and trued 10.3 Trued tyres have to cover all round the rims 10.4 Tyres can not be treated with any stuff which could modified the original grip 10.5 Minimum diameter 18mm 11. REAR TYRES 11.1 Tyres ref. 9031 glued and trued will be handed out by organisers 9031 3/32 GT3 REAR RTR 20 x 11mm GLUED and TRUED rubber tires 17" (2) 13. MOTOR WIRES 13.1 They must be the standard ones and can not have any other use 13.2 They have not to interfere with the front axle which has to be free to move up and down 13.3 They can be fixed to the chassis by glue or tape 14. BRADES 14.1 Any brades can be used as long as they are fixed to the guide by the standard NSR connectors ref. 4821 14.2 They can not be glued to the guide neither to the connectors 15. SCREWS 15.1 Only standard (as from the box) or NSR metric srews ref. 4836, 4837, 4839 for either body, motor mount, suspension 15.2 Can be fully screwed in 11.2 Each team will be supplied with 5 pairs of tyres for the whole 24h endurance race. 12. GUIDE 12.1 All the NSR guides are allowed: ref. 4841, 4842, 4843, 4844 16. MAGNETS 16.1 Absolutely forbidden 17. GENERAL MESUREMENTS 17.1 The front and rear axles width is 65 mm. 18. POWER SUPPLY 12.2 Standard NSR guide spacers are allowed to suite any driver style 4818 005 /0,12mm Pickup guide spacer brass 4819 010 /0,25mm 4820 020 /0,50mm 12.3 It is allowed to sharpen the guide blade 18.1 The power supply will be between 12.0 and 12.5 volts 19. SPARE PARTS 19.1 Each team will have to give to the organisers all the needed spare parts for the race. Such spares will be hold in a specific box available (under control) during the race 19.2 The bodyshell can not be replaced 19.3 In case of breakage of the spare chassis also, it is allowed to use one more chassis after specific technical inspection by Race Direction
Audi R8 GT3 Spare Parts GT OPTIONAL Anglewinder Chassis Guide drop arm Motor support 1402 Medium black 1234 64mm Extra Hard Red 1237 Triangular AW Xhard 1401 Soft blue 1403 Hard white Motor Pinions Crowns 3023 King EVO3 21.400 rpm Not allowed in GT3 7313 AW plastic 13 tooth 6531 AW alu 31 tooth Bushing 4803 Autolubrificant 3/32 Axles 4802 Hard Steel 60hrc 55mm Hubs 5003 Front Ø 17 5004 Rear Ø 17 Air system Tires 5226 Front 18x8 nofriction 5230 Rear 20x11 Supergrip Plastic insert 5424 BBS 17 black Screw 4833 2,2x6,5 Magnet Guides 4841 Low profile Guides Spacers Braids 4822 Super Racing Cable 4823 Extra flexible 0.25qmm Interior Suspension Kit Dimensions: Width 62,7mm Lenght 139,5mm Height 38mm Body weight GT3 19 g. Wheelbase 82,5mm Rear axle/guide distance 99,5mm 3024 Baby King 17.000 rpm 7113 AW brass 13 tooth AW alu 65282930323334 AW plastic 662627282930313233 4847 Racing no tolerance 4801 Hard Steel 60hrc 49mm 5201 Front 17x8 nofriction 9031 GT3 RTR Rear 20x11 glued and trued 5422 5426 5428 5429 5430 5431 5432 4836 Metric screw 2,2x9 4839 Metric screw 2,2x6,5 4842 4843 Longer blade 4844 Longer blade w/screw 4818 0.10mm 4819 0.25mm 4820 0.50mm 4849 Tin plated Super Racing Lexan cockpit 1228 Soft 1229 Medium 1230 Hard
Corvette C6R Spare Parts GT OPTIONAL Anglewinder Chassis Guide drop arm Motor support 1398 Medium black 1234 64mm Extra Hard Red 1237 Triangular AW Xhard 1397 Soft blue 1399 Hard white Motor Pinions Crowns Dimensions: Width Lenght Height Body weight GT3 Wheelbase Rear axle/guide distance 3023 King EVO3 21.400 rpm Not allowed in GT3 7313 AW plastic 13 tooth 6531 AW alu 31 tooth Bushing 4803 Autolubrificant 3/32 Axles 4802 Hard Steel 60hrc 55mm Hubs 5003 Front Ø 17 5004 Rear Ø 17 Air system Tires 5226 Front 18x8 nofriction 5230 Rear 20x11 Supergrip Plastic insert 5424 BBS 17 black Screw 4833 2,2x6,5 Magnet Guides 4841 Low profile Guides Spacers Braids 4822 Super Racing Cable 4823 Extra flexible 0.25qmm Interior Suspension Kit 63,8mm 141,7mm 34,8mm 21.5g. 82mm 99,6mm 3024 Baby King 17.000 rpm 7113 AW brass 13 tooth AW alu 65282930323334 AW plastic 662627282930313233 4847 Racing no tolerance 4801 Hard Steel 60hrc 49mm 5201 Front 17x8 nofriction 9031 GT3 RTR Rear 20x11 glued and trued 5422 5426 5428 5429 5430 5431 5432 4836 Metric screw 2,2x9 4839 Metric screw 2,2x6,5 4842 4843 Longer blade 4844 Longer blade w/screw 4818 0.10mm 4819 0.25mm 4820 0.50mm 4849 Tin plated Super Racing 1228 Soft 1229 Medium 1230 Hard
Porsche 997 GT3 RSR Spare Parts GT OPTIONAL Anglewinder Chassis Guide drop arm Motor support Motor Pinions Crowns Bushing Axles Hubs Tires Plastic insert Screw Magnet Guides Guides Spacers Braids Cable Interior Suspension Kit 1394 Medium black 1234 64mm Extra Hard Red 1237 Triangular AW Xhard 3023 King EVO3 21.400 rpm Not allowed in GT3 7313 AW plastic 13 tooth 6531 AW alu 31 tooth 4803 Autolubrificant 3/32 4802 Hard Steel 60hrc 55mm 5003 Front Ø 17 5004 Rear Ø 17 Air system 5226 Front 18x8 nofriction 5230 Rear 20x11 Supergrip 5424 BBS 17 black 4833 2,2x6,5 4841 Low profile 4822 Super Racing 4823 Extra flexible 0.25qmm 1393 Soft blue 1395 Hard white 3024 Baby King 17.000 rpm 7113 AW brass 13 tooth AW alu 65282930323334 AW plastic 662627282930313233 4847 Racing no tolerance 4801 Hard Steel 60hrc 49mm 5201 Front 17x8 nofriction 9031 GT3 RTR Rear 20x11 glued and trued 5422 5426 5428 5429 5430 5431 5432 4836 Metric screw 2,2x9 4839 Metric screw 2,2x6,5 4842 4843 Longer blade 4844 Longer blade w/screw 4818 0.10mm 4819 0.25mm 4820 0.50mm 4849 Tin plated Super Racing 1380 Lexan cockpit 1228 Soft 1229 Medium 1230 Hard Dimensions: Width 62,5mm Lenght 136mm Height 36mm Body weight 17g. Wheelbase 73mm Rear axle/guide distance 92mm
ASV GT3 Spare Parts GT OPTIONAL Anglewinder Chassis Guide drop arm Motor support Motor Pinions Crowns Bushing Axles Axles Spacers Hubs Tires Plastic insert Screw Guides Guides Spacers Braids Cable Interior Suspension Kit 1444 Medium black 1234 64mm Extra Hard Red 1237 Triangular AW Xhard 3023 King EVO3 21.400 rpm Not allowed in GT3 7313 AW plastic 13 tooth 6531 AW alu 31 tooth 4803 Autolubrificant 3/32 4802 Hard Steel 60hrc 55mm Front 4853 2mm plastic Rear 4815 2mm 4817 3mm 5003 Front Ø 17 5004 Rear Ø 17 Air system 5226 Front 18x8 nofriction 5230 Rear 20x11 Supergrip 5424 BBS 17 black 4833 2,2x6,5 4841 Low profile 4822 Super Racing 4823 Extra flexible 0.25qmm 1445 Soft blue 1446 Hard white 1259 Triangular AW Xhard 3024 Baby King 17.000 rpm 7113 AW brass 13 tooth AW alu 65282930323334 AW plastic 662627282930313233 4847 Racing no tolerance 4801 Hard Steel 60hrc 49mm 5201 Front 17x8 nofriction 9031 GT3 RTR Rear 20x11 glued and trued 5422 5426 5428 5429 5430 5431 5432 4836 Metric screw 2,2x9 4839 Metric screw 2,2x6,5 4842 4843 Longer blade 4844 Longer blade w/screw 4818 0.10mm 4819 0.25mm 4820 0.50mm 4849 Tin plated Super Racing 1228 Soft 1229 Medium 1230 Hard Dimensions: Width 63,5mm Lenght 140,5mm Height 35,5mm Body weight 20g. Wheelbase 82,5mm Rear axle/guide distance 95,5mm
LIST OF THE ALLOWED SPARE PARTS: Description Quantity Motor with out pinion 1 handed out by Organisers Z 13 Pinions (metal/plastic) 3 Gears 4 Chassis 1 (for each car model inscripted) Motor mount with bearings 2 Axles 2 Fronts wheels 1 pr. Rear wheels 5 pr. handed out by organizers one by one Repro wheels covers 4 (for each model inscripted) Guides 3 Guide spasers free Brades & connectors free Electrical wires free Front light set 1 Rear light set 1 Leds front & rear free Bodyshell & motor mount screws& taps free ANYTHING WHICH IT IS NOT LISTED IT MUST BE CONSIDERED FORBIDDEN