AMM-TE ammeter Manual I. Kit Details Kit Name: Ammeter Kit Kit Model: AMM-TE PCB Size: 70.6 * 39mm Screen size: 51 * 24mm Electrical parameters Operating voltage: DC5 Operating Current: 35mA Accuracy: ± 1mA Measurement range: 0 ~ 2A Outrange display: the first data 1 or -1 Display color: red Ⅱ.Circuit Diagram TL431 A 1 2 U2 5 3 5 D1 1N4148 R1 2K R2 56K R1 1K R9 2K R3 C 100R C1 101 U1 5 R4 40 100K 39 38 1 2 3 4D 4C 37 4 4B 36 5 4A 35 6 4F 104 34 7 4G J1 1 2 33 8 4E R5 C3 103 C2 32 9 3D 31 10 30 11 29 ICL7107CPLZ 益奇 3C 5 R6 1M 3B C4 474 子 L1 12 3A 47K 2.2mH 10UF /25 28 13 27 14 26 15 25 16 24 17 23 18 22 19 20 21 1G C 1C DS2 DS3 DS4 G F A E D C P B G F A E D C P B G F A E D C P B G F A E D C P B 1C 1P 2G 2F C 2A 2B 2E 2D 2C 2P 3G 3F C 3A 3B 3E 3D 3C 3P 4E 4D 4C 3F D2 1N4148 10UF /25 R7 224 3E C5 2D C6 3G 2B 1N4148 D3 C7 ZD 1 51 2C 2F C1815 2A 2E Q1 2G 1C R8 20K 1G J2 5 小 点 2 DS1 4G 4F C 4A 4B 2 1 C8 104 R10 270R 20 200 III. Circuit Principle AMM-TE ammeter is mainly composed of ICL7107, the power supply circuit, a reference voltage source, the input circuit and display circuit. 1. ICL7107 is a BCD output of the integrator Type A / D converter chip, contains internal linear
amplification, analog switches, vibration, display drivers and other components. 2. The power circuits into positive and negative supplies, the positive supply by the J2 input, C8 filter; negative power from the R8, Q1, L1, C6, C7, D2, D3 and ZD1 like, -5 voltage generated by the chip 26 feet input. 3. The reference voltage source is R1, R2, R1, R9 and U2 constituted 36 feet for the reference voltage input pin, R1 potentiometer to adjust the voltage of 100m to 36 feet. 4. Enter the circuit J1, R5, R6 and C3 constitute, by measuring the current flowing through the circuit R5, it will produce a voltage on the R5, R6 after the voltage by limiting the input to the chip 31 feet for the treatment, C3 as input voltage filter capacitor. 5. The circuit consists of DS1 ~ DS4, D1, R3 configuration, four digital tube directly driven by the chip, R10 is DS1 ~ DS3 These three LED point limiting resistor. I. Finished debugging 1. Access DC 5 voltage (note polarity), or a digital display -.000.000 is normal. 2. Use a multimeter to measure voltage chip 36 feet and 35 feet between the regulator R1 potentiometer, so this is the pressure of 100m can.. The key point voltage reference value 1. The chip 1 foot and 21 feet - voltage 5 2. The chip 36 feet and 21 feet - voltage 100m 3. The chip 26 feet and 21 feet - voltage -5 Parts list Note: Since the batch is not the same, could lead to some elements out of stock, it will be replaced with similar functions components There are some differences between the products and the list! Use the material object as the standard! Name 5-color resistance 4-color resistance Model/specific ation Serial numbe r Quantit y Name Model/specificati on Serial number 0.1R 2W R5 1 diode 1N4148 D1 D2 D3 2K R1 R9 2 voltage-regulat diode ST51 ZD1 1 56K R2 1 Transistor C1815 Q1 1 1M R6 1 inductance 2.2mH L1 1 100R R3 1 Digital tube 1bit common positive RED 270R R10 1 integrated circuit DS1~DS 4 ICL7107 U1 1 20K R8 1 TL431A U2 1 Quantit y 3 4
Monolithic capacitors CBB capacitance Dacron capacitan ce electrolytic capacitor 47K R7 1 Potentiometer 3296 1K R1 1 100K R4 1 IC socket 40P U1 1 101P C1 1 terminal 2P vertical type J2 1 104P C8 1 301-2P J1 1 474P C4 1 power line 2Psingle-end 1 1 104P C2 1 PCB board 70.6*39mm 1 1 224P C5 1 light filter 1 1 1 103P C3 1 outer skin 79*43mm 1 1 10uF/25 C6 2 screw M1.7*6 4 4 C7 Production steps Before welding please carefully read the following steps, some of the installed components must be the order, this may lead to the production of unsuccessful! 1. welding two colored ring resistance (color ring color is red dark brown brown, the same colors of the two resistance)
2. Welding a colored ring resistance (green blue black red brown) 3. Welding a colored ring resistance (brown black black yellow and brown)
4. Welding five four-color ring resistance R3 color is brown black brown golden R4 color is brown black yellow gold R7 color is yellow purple orange gold R8 color is red, black and orange gold 5. Welding three diodes, three of the same model (with direction) D1 D2 D3 model: 1N148
6. welding a Zener diode (directional) ZD1 model: ST51 7. welding a color ring inductance (color ring color is red red red silver) 8. welding three monolithic capacitors
9. Deal with the IC socket like this: 10. Place the 1st row in the red box installation position (directional)
11. Welding the 1st header row, install the four digital control (with directions) 12. After welding finished four digital tube, cut off the excess pin digital
13. Welding on the 2nd row home (with directions) 14. Welding a transistor and a reference voltage regulator chips (with direction, and note to distinguish models) Q1 model: C1815 U2 model: TL431A
15. Welding 2 CBB capacitors and two electrolytic capacitors (electrolytic capacitors have direction) 16. The welding a sampling resistor
17. The welding a potentiometer and a polyester capacitor (potentiometer directional) 18. welding power socket and input socket (both with directions)
19. Install the IC, plug in the power cord (with direction), short circuit decimal point selection joints. 20. Test Procedure: 1) Use DC 5 voltage (note polarity), digital display -.000 or.000 is normal 2) Adjust the R1 potentiometer, so between 36 feet and 35 feet voltage is100m
21. Locking four screws, finished produced.