INSTALLATION INSTRUCTIONS Accessory S Application 2010 CR-V Publications No. AII 42602-42850 Issue Date OCT 2009 PARTS LIST Fog Light Kit (With Auto Lights) P/N 08V31-SWA-100A Fog Light Kit (Without Auto Lights) P/N 08V31-SWA-100B Relay bracket 11 Wire ties Right fog light 4 Wire ties with clip Left fog light 2 Harness tapes Fog light harness 6 Self-tapping screws, 5 x 14 mm Switch harness 6 x 16 mm Washer bolt Right trim 6 mm Flange nut Left trim 20A Fuse 2 Clips Light/turn signal switch Relay 2009 American Honda Motor Co., Inc. All Rights Reserved. AII 42602-42850 (0910) 08V31-SWA-1000-9A 1 of 13
TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Flat-tip screwdriver Diagonal cutters Ratchet 10 mm Socket 10 mm Wrench Plastic trim tool T/N SILTRIMTL10 Isopropyl alcohol Shop towel Utility knife Tape Electrical tape File Blanket Illustration of the Fog Lights on the Vehicle 20A FUSE RIGHT LIGHT/TURN SIGNAL LEFT 922507AG INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. 1. Make sure you have the anti-theft code for the audio and navigation system if equipped, and write down the XM radio station presets if equipped. 2. Disconnect the negative cable from the battery. 3. Remove the front grille cover (seven clips). 7 CLIPS GRILLE COVER 920501BX 2 of 13 AII 42602-42850 (0910) 2009 American Honda Motor Co., Inc. All Rights Reserved.
4. Remove the front bumper (four self-tapping screws, six clips, and two bolts). Have an assistant help you when removing and installing the front bumper. Place the front bumper on a blanket after removal. 4 SELF- TAPPING SCREWS 6. To protect the front bumper, apply masking tape to the front bumper around the left fog light opening. MASKING TAPE 930901AG 6 CLIPS 2 BOLTS 922304BG 7. Using a utility knife, cut along the inner line of the hole as shown. Take care not to damage the front bumper. Cut out. 5. Remove five clips from the left front inner fender, and pull down the left front inner fender. LEFT INNER FENDER CROSS SECTION 3 SHORT CLIPS Cut. Cut. SHORT CLIP LONG CLIP 941701AB HOLE INNER LINE 930902AG 2009 American Honda Motor Co., Inc. All Rights Reserved. AII 42602-42850 (0910) 3 of 13
8. Cut off the four ribs on the front bumper as shown. Remove any burrs. Remove the masking tape. 10. Inside the bumper, install one clip to the front bumper. 4 RIBS Cut off. CROSS SECTION HOLDER 930903AG CLIP 922305BG 9. From the outside of the bumper, install the left trim. INSIDE VIEW PIN 11. Install the left fog light to the front bumper using three 5 x 14 mm self-tapping screws. LEFT TRIM PIN Check the L mark. LEFT TRIM OPENING Cut in step 7. 922402BG LEFT FOG LIGHT 3 SELF-TAPPING SCREWS, 5 x 14 mm 922501AG 12. Repeat steps 6 thru 11 to install the right fog light on the right side of the front bumper. 4 of 13 AII 42602-42850 (0910) 2009 American Honda Motor Co., Inc. All Rights Reserved.
Routing the Fog Light Harness 13. Route the fog light harness 1-pin connector in front of the left front inner fender as shown. Plug the fog light harness 1-pin connector to the vehicle 1-pin connector. 17. Route the fog light harness under the left headlight, and secure the fog light harness clip to the vehicle panel. 3 CLIPS LEFT HEADLIGHT BRACKET Secure the harness with no excess slack. WIRE TIE WIRE TIE 1-PIN RESONATOR PANEL SRS Do not secure. LEFT INNER FENDER 1-PIN 941702AB 14. Secure the fog light harness to the vehicle harness with two wire ties. Do not secure the fog light harness to the SRS harness. 15. Remove the vehicle ground bolt, and secure the fog light harness ground terminal to the vehicle ground terminal with the vehicle ground bolt just removed. WIRE TIE 18. Secure the other two fog light harness clips to the holes in the resonator. 19. Secure the fog light harness to the front bulkhead. With a Vehicle Harness: Cut the clips off of the two wire ties with clips. Secure the fog light harness to the vehicle harness near the harness clips using two wire ties. WITH CLIP Cut off. 2 CLIPS WITH CLIP GROUND BOLT GROUND TERMINAL GROUND TERMINAL 941703AB 16. Secure the fog light harness to the vehicle harness with two wire ties. 931201AG 2009 American Honda Motor Co., Inc. All Rights Reserved. AII 42602-42850 (0910) 5 of 13
Without a Vehicle Harness: Secure the fog light harness to the bumper beam using two wire ties with clip and one wire tie. Without a Vehicle Harness: Secure the fog light harness to the bumper beam using two wire ties with clip and one wire tie. PANEL WIRE TIE BEAM BEAM WITH CLIP 6303011B 20. Route the fog light harness under the bumper beam towards the right side of the vehicle. Secure the fog light harness. With a Vehicle Harness: Cut the wire ties off of the two wire ties with clip. Secure the fog light harness to the vehicle harness using three wire ties. BEAM WIRE TIE 21. Using isopropyl alcohol on a shop towel, clean the bumper beam surface where the harness tape will attach. WITH CLIP BEAM BEAM WIRE TIE WITH CLIP Cut off. 2 CLIPS WITH CLIP 2 TAPES 22. Continue routing the fog light harness along the bumper beam to the right side of the vehicle. Secure the fog light harness under the bumper beam using two adhesive tapes and two wire ties connected together. 6 of 13 AII 42602-42850 (0910) 2009 American Honda Motor Co., Inc. All Rights Reserved.
23. Route the fog light harness as shown, and secure the clip on the fog harness to the vehicle panel. PANEL FOG LIGHT 25. Reinstall the inner fender. With the help of an assistant, bring the front bumper close to the vehicle, and plug the fog light harness 2-pin connectors into the right and left fog lights. Reinstall the front bumper. 2-PIN 2-PIN CLIP 6303042B 24. Secure four remaining fog light harness clips to the holes in the vehicle panel. Install position. PANEL RIGHT LEFT 922502BG Routing the Switch Harness 26. Remove the driver s dashboard under cover (turn the knob and release the pin and the clip. PANEL KNOB Turn. PIN 4 CLIPS 6303053B DRIVER S DASHBOARD UNDER COVER CLIP 6303080B 2009 American Honda Motor Co., Inc. All Rights Reserved. AII 42602-42850 (0910) 7 of 13
27. Remove the driver s dashboard lower cover (seven clips and two hooks). 29. Pull back the door opening seal from around the driver s kick panel, and remove the driver s kick panel (two clips). 7 CLIPS DOOR OPENING SEAL Pull back. 2 CLIPS DRIVER S DASHBOARD LOWER COVER HOOK 6303071B 28. Remove the left front side step trim (three clips). 3 CLIPS DRIVER S KICK PANEL 6303100B 30. Lower the tilt lever. Using a flat-tip screwdriver, release one of the retaining tabs from the steering column lower cover. RETAINING TAB STEERING COLUMN LOWER COVER LEFT SIDE STEP TRIM 6303090B TILT LEVER FLAT-TIP SCREWDRIVER 6905030Y 8 of 13 AII 42602-42850 (0910) 2009 American Honda Motor Co., Inc. All Rights Reserved.
31. Remove the steering column upper cover (two retaining tabs on each side). 33. Plug the relay into the switch harness relay block. 2 RETAINING TABS STEERING COLUMN UPPER COVER RELAY Push. RELAY BRACKET RELAY BLOCK 6828010B 6819020Y 32. Remove the steering column lower cover (two selftapping screws and one screw). 34. Install the relay bracket to the switch harness relay block. 35. Install the switch harness relay block on the vehicle panel using the 6 x 16 mm washer-bolt and the 6 mm flange nut. STEERING COLUMN LOWER COVER PANEL RELAY BLOCK SELF-TAPPING SCREW SCREW 6819030Y 6 x 16 mm WASHER-BOLT FUSE BOX 6 mm FLANGE NUT 6303130B 2009 American Honda Motor Co., Inc. All Rights Reserved. AII 42602-42850 (0910) 9 of 13
36. Plug the switch harness 2-pin connector into the vehicle harness 2-pin connector. Secure the switch harness to the vehicle harness using two wire ties. 2-PIN 38. Get the fog light switch harness, and insert the white and pink switch harness terminals into the appropriate cavities of the white vehicle 34-pin connector. SIDE VIEW 34-PIN (white.) 2-PIN WHITE WIRE TERMINAL PINK WIRE TERMINAL PINK WIRE TERMINAL WHITE WIRE TERMINAL ELECTRICAL TAPE FUSE BOX WIRE TIE WIRE TIE 940903AG 37. Push the retaining tab (from the vehicle green 42-pin connector, the white 34-pin connector, and the blue 21-pin connector), and raise the lock lever from each connector. Remove the connectors from the fuse box. Close the lock and vehicle white 43-pin connector, and remove the cover by sliding it away from the lock. 931203AG 39. Secure the switch harness to the vehicle harness with electrical tape. 40. Reinstall the connector cover, and reconnect the vehicle connectors. 41. Secure the switch harness to the vehicle harness using two wire ties. VIEWED FROM 42-PIN 34-PIN 21-PIN WIRE TIE Push. Slide. FUSE BOX COVER Push. RETAINING TAB FUSE BOX Push. 931204AG LOCK LEVER FUSE BOX S 34-PIN 6303150B 10 of 13 AII 42602-42850 (0910) 2009 American Honda Motor Co., Inc. All Rights Reserved.
42. Turn the steering wheel 90 counterclockwise, and unplug the vehicle connector from the light/turn signal switch. 44. Install the new light/turn signal switch on the steering column with two self-tapping screws. While installing do not hold the light switch by the lever. HOLDER TAB HOLE STEERING COLUMN LIGHT/TURN SIGNAL CASE LIGHT/TURN SIGNAL STEERING WHEEL 6303180B LEVER RETAINING TAB NEW LIGHT/TURN SIGNAL SELF-TAPPING SCREW 7109020E 43. Remove the two self-tapping screws from the light/ turn signal switch. While pushing the retaining tab, slide the light/turn signal switch, and remove it from the steering column. While removing, do not hold the light/turn signal switch by the lever. 45. Plug the vehicle connector into the new light/turn signal switch. HOLDER TAB HOLE STEERING COLUMN CASE NEW LIGHT/ TURN SIGNAL NEW LIGHT/TURN SIGNAL RETAINING TAB 6303210B LEVER LIGHT/TURN SIGNAL SELF-TAPPING SCREW 7109010E 2009 American Honda Motor Co., Inc. All Rights Reserved. AII 42602-42850 (0910) 11 of 13
46. If the 20A fuse is already installed in the fuse box, go to step 47, otherwise install the 20A fuse to the fuse box. FUSE BOX Fog Light Aiming Adjustment 51. Adjust the fog light: Pull down the inner fender and under cover. Adjust the aiming according to local laws and regulations. To adjust, turn the aiming adjustment knob in or out until the correct aiming is obtained. 52. Reinstall the bumper clips and bolts. FUSE BOX PLUGGING POINT To lower. To raise. 20A FUSE VIEWED FROM 6303220B 47. Check that all wire harnesses are routed properly and all connectors are plugged in. 48. Reinstall all removed parts. Do not reinstall the bumper clip and bolts that fasten the bumper at this time. Check that all clips and fasteners are installed securely. 49. Reconnect the negative cable to the battery. 50. Reset the clock, and reset the XM radio presets (if equipped). USE AND CARE How to Operate the Fog Lights AIMING ADJUSTMENT KNOB 922503AG Turn the lights switch to the position (headlights on low beam). Turn the fog light switch on (indicator is on). HEADLIGHT ON OFF AUTO/ Low High OFF - - - - - - ON - NOTE: The fog light lenses can cloud when the outside temperature is cold; this is normal and should go away in warm weather. If the fog lights do not turn on, check the fuse and all the connectors, including the ground cable. 12 of 13 AII 42602-42850 (0910) 2009 American Honda Motor Co., Inc. All Rights Reserved.
BULB REPLACEMENT 1. Remove one bolt and one clip, and pull down the under cover and inner fender. 4. Install the new bulb and socket to the fog light. Use only a Guine Honda halogen light bulb of specified wattage. Rating: 12V 55W H11 Halogen Light Bulb P/N 33165-S5A-003. Do not touch the bulb. Oily or greasy substances on the bulb can shorten its service life due to the heat produced when the bulb is turned on. If the bulb is accidentally touched, wipe it clean with a soft cloth that has been dampened with a denatured alcohol or a mild detergent solution. Align the tab on the fog light with the cutout in the bulb when installing the new bulb. If not aligned, the fog light may annoy oncoming drivers. CLIP BOLT 922504AG Turn. 2. Unplug the connector from the fog light. NEW BULB LEFT NEW BULB 922506AG BULB 5. Reinstall the removed parts in the reverse order of removal. Check that the wire harnesses are not pinched. Be sure to tighten the clip and bolts securely. 6. Check the operation of the fog light; adjust the aiming if necessary. 922505AG 3. Remove the bulb. 2009 American Honda Motor Co., Inc. All Rights Reserved. AII 42602-42850 (0910) 13 of 13