Illustrated Parts List. Ordering Parts For your convenience, replacement parts and accessories can be ordered from ARPAC by fax 24 hours a day. Please have the following information available to ensure quick, easy, and accurate service. Your name and telephone number Your P.O. (Purchase Order) number Your preferred method of delivery Replacement Parts Policy & Contact Information Should a replacement part be needed, ARPAC s return material authorization policy must be adhered to. ARPAC will not distribute equipment or parts without a purchase order from an authorized ARPAC distributor. This procedure includes warranty and nonwarranty replacement parts. A return authorization will be issued at that time, and credit will not be issued until the suspect part has been received and inspected. Call ARPAC sales for the distributor in your area at (847) 678-9034. ARPAC Parts Contact Information Phone: (847) 678-9034 Fax: (847) 678-209 24 Hour Emergency Service: (800) 424-0545 parts@arpac.com Open for service Monday through Friday, 7:00 AM to 6:00 PM (Central Time). Ordering Parts -
.2 How to Use This Parts List General Part Numbers This chapter contains all part numbers necessary to order L-Series Automatic L-Bar Sealer replacement parts and assemblies. This illustrated parts breakdown is presented in disassembled order. Detail parts are shown below their respective upper level assemblies whenever possible. The parts lists follow the illustration for a particular assembly and represent components of that assembly. The number listed in the quantity column is the number of the specific part required to complete the assembly and may not reflect the quantity needed for the entire system. The lists are divided into four columns. The item/index numbers refer to the identification number located on the drawing. The part number is the Arpac part number, used to identify the part for ordering. The part description column lists each part name, and the quantity column lists the quantity of that part used in that particular assembly. Illustrations are shown before the parts list for each assembly. -2.2 How to Use This Parts List
.3 Commonly Ordered Parts Part Description L-8 P/N L-26 P/N Seal Pad, /4 x 3/4 Soft (6 ft.) 8880 8880 2 Teflon Tape (3 mil) ( rl) 87372 87372 Silicone Grease ( tube) 87286 87286 T/D Seal Blade ( ea.) 94974 9504 M/D Seal Blade ( ea.) 94973 95043 T/D Heater ( ea.) 87077 8755 M/D Heater ( ea.) 87075 8754 Solid State Relay (24 VDC) (ea.) 8734 8734 Thermocouple ( ea.) 87076 87076 Infeed Conveyor Belt - Green Smooth Top (Standard) 8707 8760 Infeed Conveyor Belt - White Smooth Top (Food 8767 8779-00 Grade Applications) Infeed Conveyor Belt - Green Rough Top (Dry Ice 827038 827003-00 Applications) OutfeedConveyor Belt - Green Smooth Top (Standard) 8748 8763 OutfeedConveyor Belt - White Smooth Top (Food 8767-002 82704 Grade Applications) OutfeedConveyor Belt -Green Rough Top (Dry Ice 827039 827040 Applications) Upper Scrap Belt ( ea.) 87066 8753 Lower Scrap Belt ( ea.) 87069 87078 Seal Head Solenoid (24VDC ) ( ea.) 874 874 Temperature Controller 804023-026 804023-026 Photo Sensor Transmitter DC with 6 in Pigtail 804007-33 804007-33 Photo Sensor Receiver DC with 6 in Pigtail 804007-34 804007-34 Relay, Control 2PDT Coil=24VDC Slim Line-Relay 804008-069 804008-069 Relay, Solid-State PST Coil=5+VDC 8734 8734 Table -: Commonly Ordered Parts.3 Commonly Ordered Parts -3
.4 List of Options L-8 P/N L-26 P/N Description 22793 22793 Lugged Infeed Conveyor Core (Refer to Section.30 6 Lugged Infeed Conveyor Core (Option) [22793] on page -66 for breakdown of assembly) 97353 97353 480 VAC Conversion Kit (Refer to Section.3 480VAC Conversion Kit (Option) on page -68 for breakdown of assembly) 97355 97346 Lower Film Cradle (Refer to Section.32 Lower Film Cradle (Option) [97355] on page -69 for breakdown of assembly) 94576 94576 Auxilliary Emergency Stop Button (Refer to Section.33 Auxiliary Emergency Stop Button (Option) [94576] on page -70 for breakdown of assembly) 97362.000A 97362.000A Auxiliary Infeed Conveyor Control Relay (Refer to Section.34 Auxiliary Infeed/Discharge Conveyor Control Relay (Option) [97362.000A] on page -7 for breakdown of assembly) 94595 94595 Vertical Photoeye (Refer to Section.35 Vertical Photoeye (Option) [94595] on page -72 for breakdown of assembly) 97340 97340 Pneumatic Hole Punch (Refer to Section.36 Pneumatic Hole Punch (Option) [97340] on page -73 for breakdown of assembly) 94572 94572 Product Guide (Refer to Section.37 Infeed Product Guide (Option) [94572] on page -74 for breakdown of assembly) 94582 94583 Seal Opening Kit (Refer to Section.38 Seal Opening Kit (Option) on page -75 for breakdown of assembly) 94578 94578 Stack Light (Refer to Section.39 Stack Light (Option) [94578] on page -76 for breakdown of assembly) 94575-00 94575-00 Registration Kit (Refer to Section.40 Registration Kit (Option) [94575] on page -77 for breakdown of assembly) Table -2: List of Options -4.4 List of Options
Page Intentionally Blank.4 List of Options -5
.5 Overall Assemblies 9 5 4 8 7 6 0 2 3 9 Figure -. Overall Assemblies -6.5 Overall Assemblies
Fig ref. L-8 P/N L-26 P/N Description Qty 9706 9706-500 Frame Assembly (Refer to Section on page -0 for breakdown of assembly) 2 9707 9707-500 Trim Rewind Assembly (Refer to Section.8 Trim Rewind Assembly on page -2 for breakdown of assembly) 3 9708 9708-500 Seal Head Assembly (Refer to Section.9 L-8 Seal Head Assembly (254526) on page -4 or Section. 0 L-26 Seal Head Assembly (25866) on page -8 for breakdown of assembly) 4 9709 9709-500 Seal Head Frame Assembly (Refer to Section.2 Seal Head Frame Assembly on page -42 for breakdown of assembly) 5 97-000A 97-500 Film Unwind Assembly (Refer to Section.22 Film Unwind Assembly on page -46 for breakdown of assembly) 6 972-000A 972-500 Take Away Assembly (Refer to Section.23 Take Away Assembly on page -50 for breakdown of assembly) 7 973-000B 973-500 Outfeed Apron Assembly (Refer to Section.24 Outfeed Apron Assembly on page -54 for breakdown of assembly) 8 974-000A 974-500 Outfeed Slide Conveyor Assembly (Refer to Section.25 Outfeed Slide Conveyor on page -56 for breakdown of assembly) 9 - - Electrical Components (Refer to Section.26 Electrical Components (Part ) on page -60 for breakdown of assembly) 0 - - Pneumatic Components (Refer to Section.29 Pneumatics Components on page -65 for breakdown of assembly) 9705.000A 9705-500 Infeed Conveyor Assembly (Refer to Section.6 Infeed Conveyor Assembly on page -8 for breakdown of assembly) Table -3: Overall Assemblies.5 Overall Assemblies -7
.6 Infeed Conveyor Assembly 43 42 9 25 28 54 60 35 34 4 37 38 47 40 48 5 26 36 32 33 67 39 66 44 65 69 6 5 7 8 30 56 9 57 34 58 0 70 46 45 68 9 2 3 4 6 34 59 2 5 55 8 64 3 22 2 9 52 4 3 49 23 24 6 20 50 7 62 53 39 63 5 Washer 3 29 27 Figure -2. Infeed Conveyor Assembly -8.6 Infeed Conveyor Assembly
Fig ref. L-8 P/N L-26 P/N Description Qty A 827038 827003-00 Conveyor Belt Green Rough Top - Dry Ice B 8767 8779-00 Conveyor Belt White Smooth Top (Food Grade) C 8707 8760 Conveyor Belt Green Smooth Top 2 800459 800459 Drive Chain 3 95004 96247 Screw Block 4 94739 94832 Screw Rod 5A 804007.00 804007.00 Photoeye, Transmitter 5B 804007.003 804007.003 Photoeye, Receiver 6 94783 94833 Nut Plate 2 7 94784 94834 Plate Nut 2 8 94785 94785 Bracket; Photoeye 2 9 87057 87057 Wing Nut 3 0 955 9526 Conveyor Bed Plate 94945 95028 Lower Film Former 2 94950 22287 Bar Support 3 94755 94755 Nut Plate 2 4 94706 94836 Nut Plate 5 95007 95026 Drive Roller 6 9500 9500 Guard 7 950 95020 Guard 8 9503 22288 Motor Mount 9 9475 94844 Slide Rod 2 20 87063 87063 Motor & Reducer 2 9470 9470 Nut Plate 4 22 87098 87098 Pillow Block Bushing 4 23 94707 94707 Block 2 24 87698 87698 Bearing 2 25 9504 95022 Scale 26 9494 9494 Mounting Block 27 94959 95024 Guide 28 9478 9478 Pointer 29 94753 94840 Pointer 30 956 9523 Upper Film Former 3 87069 87069 Handwheel 32 94756 94842 Screw 33 9470 94838 Slide Rod 2 34 87068 87068 2 Hole Bearing 3 35 94754 94754 Plate Table -4: Infeed Conveyor Assembly.6 Infeed Conveyor Assembly -9
Fig ref. L-8 P/N L-26 P/N Description Qty 36 8752 8752 Garlock Busing 2 37 26278-003 26278-003 Roller Tube 2 38 94799 94853 Roller Shaft 2 39 87090 87090 Circlip 6 40 94792 94792 Bushing 4 22289 Bracket 4 94850 94850 Roller Bracket, Front 42 9485 9485 Roller Bracket, Rear 43 950 95032 Bracket 44 94789 94835 Photoeye Bracket 45 9505 9509 Photoeye Bracket 46 94703 94839 Bar 47 94786 9484 Upper Film Support Rod 48 9469 9469 Block 49 94758 94846 Roller Tube 50 8744 8744 Bearing 2 5 87054 87054 Snap Ring 2 52 94760 94848 Roller Shaft 53 9476 9476 Collar 2 54 94752 94752 Bracket 55 957 958 Guard 56 94709 94843 Bracket 57 956 958 Frame 58 959 9525 Pan 59 87085 87085 Sprocket, RS35B2 2 60 94884 94884 Extension Block Bushing 2 6 94892 94893 Roller Tube, Idler 62 9685 94894 Shaft 63 8782 8782 Bearing 2 64 9506 95062 Idler Roller Mounting Bracket 65 94889 9489 Nose Roller Tube 3 66 9499 9496 Shaft 67 94920 94920 Bearing 6 68 e8795r 8795 Fender Washer 6 69 94693 94693 Bushing Housing, Center/Rear 3 70 94699 94699 Bushing Housing, Front 7 94896 94896 Nut Block Table -4: Infeed Conveyor Assembly -0.6 Infeed Conveyor Assembly
.7 Frame Assembly 7 6 8 2 3 2 4 3 4 5 9 0 Figure -3. Frame Assembly 5 6 Fig ref. L-8 P/N L-26 P/N Description Qty 94942 95037 Cover 2 947 94869 Cover 4 9565 9590 Cover Discharge (Clear) 5 94947 22307 Cover Discharge Lower 7 9566 9566 Cover, Top 8 94962 95036 Bracket 0 94704 94704 Screw, Levelings 4 87095 87095 Caster 4 2-953 Cover (Clear) 3 94705 94868 Cover For Duct 4 970 Frame, Main 5 94944 95040 Door (Clear) 6 9508 9533 Lower Door (Clear) Table -5: Frame Assembly.7 Frame Assembly -
.8 Trim Rewind Assembly 9 2 7 25 22 5 8 20 6 2 7 23 3 3 29 8 9 5 0 2 30 27 4 8 28 24 26 25 6 4 32 3 Figure -4. Trim Rewind Assembly -2.8 Trim Rewind Assembly
Fig ref. L-8 P/N L-26 P/N Description Qty 94764 94764 Cam 2 94763 94763 Counter Weight 3 95088 95088 Dancer Arm 4 94970 94970 Bearing Housing 5 9497 9497 Shaft 6 94766 94766 Bushing; Flanged 7 94767 94767 Roller; Tube 8 87082 87082 Motor 9 95085 95085 Motor Mount 0 87080 87080 Drive Sprocket 87079 87079 Chain 2 8708 8708 Driven Sprocket 3 94964 94964 Spool End, Inner 4 94965 94965 Spool End, Outer 5 94967 94967 Hub, Inner 6 94968 94968 Hub, Outer 7 9496 9496 Shaft 8 8746 8746 Bearing, NSK 6804Z 9 94992 95052 Bracket 20 94804 94804 Roller 2 94805 94805 Axle 22 94662 94662 Hub 2 23 8739 8739 Roller Plunger 24 9688 9688 Core 25 8783 8783 E Clip 4 26 94900 94900 Retainer; Spring 2 27 8784 8784 Spring 28 94903 94903 Brake; Leather 29 9490 9490 Bracket; Leathermounting 30 94902 94902 Bracket; Lower 3 8785 8785 Knob; 3 Lobe 32 8786 8786 Washer; Fender Table -6: Trim Rewind Assembly -3
.9 L-8 Seal Head Assembly (254526) 39 36 3 29 28 Item 7 (on Seal Head Frame Assembly) 27 35 Item 9 (on Seal Head Frame Assembly) 6 7 5 4 3 2 Item 4 (on Seal Head Frame Assembly) 0 37 Item 2 (on Seal Head Frame Assembly) 2 4 8 3 22 23 4 4 3 Item 5 (on Seal Head Frame Assembly) 8 9 Figure -5. L-8 Seal Head Assembly -4.9 L-8 Seal Head Assembly (254526)
Fig ref. Part number Description Qty 9568 T/D Seal Bar Support 2 95095 T/D Film Clamp, Inner, PE, L8 Hanagata 0Z 3 87076 Thermocouple, Type K, Sheath 30MM Long 3MM DIA, Leads 92mm Long (65MM Split W/spad) 2 8 94735 Insulator 6 9 226429 T/D Film Clamp, Outer, PE, L8, Hanagata 0Z 0 226427 M/D Film Clamp, Inner, L8, Hanagata 0Z 94734 Stud 4 2 87073 Spring 4 3 9477 Block 4 4 9475 Sensor Plate 4 5 8738 (Safety Switch) Proximity Sensor, DC 2-4 Wire 5.0MM NC 2M-Cable 6 9472 Insulator 4 7 9472 Mounting Plate 4 9 94976 M/D Bar Mount Assembly 22 226428 M/D Film Clamp, Outer, PE, L8, Hanagata 0Z 23 95096 M/D Seal Head Support 27 9567 T/D Anvil Support Bar 28 94983 Block 29 87088 Floating Joint 3 87084 Seal Head Cylinder 34 94733 Spacer 4 35 95083 M/D Anvil Support Bar 36 9495 M/D Anvil Mounting 37 94953 T/D Anvil Mounting 39 87099 Reed Switch, DC 2-Wire 40 253045 Insulator 4A XXXXX L-8 Seal Bar Assembly -Standard (Refer to Section. L-8 Seal Bar Assembly Standard (XXXXX) on page -22 for breakdown of assembly). Table -7: L-8 Seal Head Assembly.9 L-8 Seal Head Assembly (254526) -5
Fig ref. Part number Description Qty 4B 26585 L-8 Seal Bar Assembly Blacksparkle - Polyolefin (Refer to Section.2 L-8 Seal Bar Assembly Blacksparkle - Polyolefin (26585) on page -24 for breakdown of assembly). 4C 26586 L-8 Seal Bar Assembly Mushroom Radius Corner - Polyolefin, PVC (Refer to Section.3 L-8 Seal Bar Assembly Mushroom Radius Corner - Polyolefin, PVC (26586) on page -26 for breakdown of assembly). 4D 26587 L-8 Seal Bar Assembly Mushroom Straight Corner - Polyolefin, PVC (Refer to Section.4 L-8 Seal Bar Assembly Mushroom Straight Corner - Polyolefin, PVC (26587) on page -28 for breakdown of assembly). 4E 26588 L-8 Seal Bar Assembly Plasma - Polyethelyne, PVC (Refer to Section.5 L- 8 Seal Bar Assembly Plasma - Polyethelyne Polyolefin, PVC (26588) on page -30 for breakdown of assembly). Table -7: L-8 Seal Head Assembly -6.9 L-8 Seal Head Assembly (254526)
Page Intentionally Blank.9 L-8 Seal Head Assembly (254526) -7
. 0 L-26 Seal Head Assembly (25866) 39 36 3 29 28 Item 7 (on Seal Head Frame Assembly) 27 35 Item 9 (on Seal Head Frame Assembly) 6 7 5 4 3 2 Item 4 (on Seal Head Frame Assembly) 0 37 Item 2 (on Seal Head Frame Assembly) 2 4 8 3 22 23 4 4 3 Item 5 (on Seal Head Frame Assembly) 8 9 Figure -6. L-26 Seal Head Assembly -8. 0 L-26 Seal Head Assembly (25866)
Fig ref. Part number Description Qty 956 Frame 2 204052 Plate, Stripper 3 87076 Thermocouple, Type K, Sheath 30MM Long 3MM DIA, Leads 92mm Long (65MM Split W/spad) 2 4 95048 T/D Bar Mount Assembly 8 94735 Insulator 6 9 20405 Plate, Stripper, Outer, T/D L26 0 204053 Plate, Stripper, Inner, M/D, L26 94734 Stud 4 2 87073 Spring 4 3 9477 Block 4 4 9475 Sensor Plate 4 5 87074 (Safety Switch) Proximity Sensor, DC 2-4 Wire 5.0MM NC 2M-Cable 6 9472 Insulator 4 7 9472 Mounting Plate 4 9 95042 M/D Bar Mount Assembly 22 204054 Plate, Stripper, Outer, M/D, L26 27 9592 T/D Anvil Support Bar 28 95049 Block 29 87088 Floating Joint 3 8762 Seal Head Cylinder 34 94733 Spacer 4 35 9539 M/D Anvil Support Bar 36 95047 M/D Anvil Mounting 37 95044 T/D Anvil Mounting 39 87099 Reed Switch, DC 2-Wire 40 87372 Tape, Teflon 2 x.003 x 0 Yards.43 4A XXXXX L-26 Seal Bar Assembly -Standard (Refer to Section.6 L-26 Seal Bar Assembly Standard (XXXXX) on page -32 for breakdown of assembly). 4B 26589 L-26 Seal Bar Assembly Blacksparkle - Polyolefin (Refer to Section.7 L-26 Seal Bar Assembly Blacksparkle - Polyolefin (26589) on page -34 for breakdown of assembly) Table -8: L-26 Seal Head Assembly. 0 L-26 Seal Head Assembly (25866) -9
Fig ref. Part number Description Qty 4C 26590 L-26 Seal Bar Assembly Mushroom Radius Corner - Polyolefin, PVC (Refer to Section.8 L-26 Seal Bar Assembly Mushroom Radius Corner - Polyolefin, PVC (26590) on page -36 for breakdown of assembly) 4D 2659 L-26 Seal Bar Assembly Mushroom Straight Corner - Polyolefin, PVC (Refer to Section.9 L-26 Seal Bar Assembly Mushroom Straight Corner - Polyolefin, PVC (2659) on page -38 for breakdown of assembly) 4E 26592 L-26 Seal Bar Assembly Plasma - Polyethelyne, PVC (Refer to Section.20 L- 26 Seal Bar Assembly Plasma - Polyethelyne Polyolefin, PVC (26592) on page -40 for breakdown of assembly) Table -8: L-26 Seal Head Assembly -20. 0 L-26 Seal Head Assembly (25866)
Page Intentionally Blank. 0 L-26 Seal Head Assembly (25866) -2
. L-8 Seal Bar Assembly Standard (XXXXX) Standard Seal Bar Used on Polyolefin Film with Narrow Width Seal 7 3 8 9 2 3 0 0 4 5 6 2 Figure -7. L-8 Seal Bar Assembly Standard -22. L-8 Seal Bar Assembly Standard (XXXXX)
Fig ref. Part number Description Qty 94974 T/D Seal Bar Blade - Standard 2 95090 T/D Seal Blade Insert 3 87077 T/D Heater Cartiridge 4 87075 M/D Heater Cartidge 5 94973 M/D Seal Bar Blade - Standard 6 9509 M/D Seal Bar Body, Set 7 9478 T/D Seal Pad 8 94954 T/D Seal Anvil 9 94720 Side Plate 0 94732 Side Plate 2 9473 M/D Seal Pad 2 94952 M/D Seal Anvil 3 9479 Side Plate Table -9: L-8 Seal Bar Assembly Standard. L-8 Seal Bar Assembly Standard (XXXXX) -23
.2 L-8 Seal Bar Assembly Blacksparkle - Polyolefin (26585) Black Speckle Seal Bar Used on Sticky Polyolefin & Sticky Polyethylene Film with Wide Seal Flow Direction Blade (M/D) Tranverse Direction Blade (T/D) 7 3 8 9 2 3 5 5 0 0 4 6 5 2 4 6 Figure -8. L-8 Seal Bar Assembly Blacksparkle -24.2 L-8 Seal Bar Assembly Blacksparkle - Polyolefin (26585)
Fig ref. Part number Description Qty 2372-025 Blade, Knife, 8.0", Bar, Seal, Coated 2 226378 Halves, Bar, Seal, 460MM, T/D, L8 3 87077 Heater, Cartridge, T/D(0Z), 200V, 400W 8."LG, 0.392 DIA +/- 0.004",6LG Lead 4 87075 Heater, Cartridge, M/D(0Z), 200V, 450W, 9.5" LG, 0.392 DIA +/-.004", 6LG Lead 5 204036-0 Blade, Knife, Bar, Seal, M/D, 0Z, Blacksparkle Coated 6 226376 Halves, Bar, Seal, 495MM, M/D, L8 7 9478 T/D Seal Pad 8 94954 T/D Seal Anvil 9 94720 Side Plate 0 94732 Side Plate 2 9473 M/D Seal Pad 2 94952 M/D Seal Anvil 3 9479 Side Plate 4 204037-00A Insert, Bar, Seal, Plasma, T/D, Notched, 0Z, 460MM=8.0" 5 239082-00 Inserts, Bar, Seal, Plasma, 9.625 LG, M/ D, (Set) 6 073 23 Insert, Bar, Seal, Plasma, 460MM Long, T/D, 460MM=8.0" Table -0: L-8 Seal Bar Assembly Blacksparkle - Polyolefin.2 L-8 Seal Bar Assembly Blacksparkle - Polyolefin (26585) -25
.3 L-8 Seal Bar Assembly Mushroom Radius Corner - Polyolefin, PVC (26586) Mushroom Radius Corner Blade Set Used on Polyethylene Film with Narrow Width Seal & a Tight Square Corner Typical Mushroom Inserts and Blades 7 2 8 9 4 5, 3 3 0 0 4 5,2 6 Figure -9. L-8 Seal Bar Assembly Mushroom Radius - Polyolefin, PVC -26.3 L-8 Seal Bar Assembly Mushroom Radius Corner - Polyolefin, PVC (26586)
Fig ref. Part number Description Qty 82552 Blade, Cutting, Front, Arrow, Bar, Seal L8 2 9479 Side Plate 3 87077 Heater, Cartridge, T/D(0Z), 200V, 400W 8."LG, 0.392 DIA +/- 0.004",6LG Lead 4 87075 Heater, Cartridge, M/D(0Z), 200V, 450W, 9.5" LG, 0.392 DIA +/-.004", 6LG Lead 5 82552-00 Blade, Cutting, Cross, Arrow, Bar, Seal L8 6 94952 M/D Seal Anvil 7 9478 T/D Seal Pad 8 94954 T/D Seal Anvil 9 94720 Side Plate 0 94732 Side Plate 2 9473 M/D Seal Pad 2 82549 Insert, Front, Arrow, Bar, Seal, Radius 3 82549-00 Insert, Cross, Arrow, Bar, Seal, Radius 4 95090 T/D Seal Blade Insert 5 9509 M/D Seal Bar Body, Set Table -: L-8 Seal Bar Assembly Mushroom Radius Corner.3 L-8 Seal Bar Assembly Mushroom Radius Corner - Polyolefin, PVC (26586) -27
.4 L-8 Seal Bar Assembly Mushroom Straight Corner - Polyolefin, PVC (26587) Mushroom Square Corner Blade Set Used on Polyethylene Film with Narrow Width Seal Typical Mushroom Inserts and Blades 7 2 8 9 4 5, 3 3 0 0 4 5,2 6 Figure -0. L-8 Seal Bar Assembly Straight Corner - Polyolefin, PVC -28.4 L-8 Seal Bar Assembly Mushroom Straight Corner - Polyolefin, PVC (26587)
Fig ref. Part number Description Qty 82557 Blade, Cutting, Front, Arrow, Bar, Seal L8 2 9479 Side Plate 3 87077 Heater, Cartridge, T/D(0Z), 200V, 400W 8."LG, 0.392 DIA +/- 0.004",6LG Lead 4 87075 Heater, Cartridge, M/D(0Z), 200V, 450W, 9.5" LG, 0.392 DIA +/-.004", 6LG Lead 5 82557-00 Blade, Cutting, Cross, Arrow, Bar, Seal L8 6 94952 M/D Seal Anvil 7 9478 T/D Seal Pad 8 94954 T/D Seal Anvil 9 94720 Side Plate 0 94732 Side Plate 2 9473 M/D Seal Pad 2 82556 Insert, Front, Arrow, Bar, Seal, Straight 3 82556-00 Insert, Cross, Arrow, Bar, Seal, Straight 4 95090 T/D Seal Blade Insert 5 9509 M/D Seal Bar Body, Set Table -2: L-8 Seal Bar Assembly Mushroom Straight Corner.4 L-8 Seal Bar Assembly Mushroom Straight Corner - Polyolefin, PVC (26587) -29
.5 L-8 Seal Bar Assembly Plasma - Polyethelyne Polyolefin, PVC (26588) Plasma Seal Bar Used on Non-Stick Polyolefin & Polyethylene Film with Wide Seal Flow Direction Blade (M/D) Tranverse Direction Blade (T/D) 7 3 8 9 2 3 5 5 0 0 4 6 5 2 4 6 Figure -. L-8 Seal Bar Assembly Plasma - Polyethelyne, Polyolefin, PVC -30.5 L-8 Seal Bar Assembly Plasma - Polyethelyne Polyolefin, PVC (26588)
Fig ref. Part number Description Qty 047-04 Blade, Knife, 8.0", Bar, Seal, T/D 460mm=8.0 2 226378 Halves, Bar, Seal, 460MM, T/D, L8 3 87077 Heater, Cartridge, T/D(0Z), 200V, 400W 8."LG, 0.392 DIA +/- 0.004",6LG Lead 4 87075 Heater, Cartridge, M/D(0Z), 200V, 450W, 9.5" LG, 0.392 DIA +/-.004", 6LG Lead 5 204036-0 Blade, Knife, Bar, Seal, M/D, 0Z, Blacksparkle Coated 6 226376 Halves, Bar, Seal, 495MM, M/D, L8 7 9478 T/D Seal Pad 8 94954 T/D Seal Anvil 9 94720 Side Plate 0 94732 Side Plate 2 9473 M/D Seal Pad 2 94952 M/D Seal Anvil 3 9479 Side Plate 4 204037-00A Insert, Bar, Seal, Plasma, T/D, Notched 5 239082-00 Inserts, Bar, Seal, Plasma, M/D (Set) 6 073-23 Insert, Bar, Seal, Plasma, T/D Table -3: L-8 Seal Bar Assembly Plasma.5 L-8 Seal Bar Assembly Plasma - Polyethelyne Polyolefin, PVC (26588) -3
.6 L-26 Seal Bar Assembly Standard (XXXXX) Standard Seal Bar Used on Polyolefin Film with Narrow Width Seal 7 3 8 9 2 3 0 0 4 5 6 2 Figure -2. L-26 Seal Bar Assembly Standard -32.6 L-26 Seal Bar Assembly Standard (XXXXX)
Fig ref. Part number Description Qty 9504 T/D Seal Bar Blade - Standard 2 9540 T/D Seal Blade Insert 3 8755 T/D Heater Cartiridge 4 8754 M/D Heater Cartidge 5 95043 M/D Seal Bar Blade - Standard 6 954 M/D Seal Bar Body, Set 7 9487 T/D Seal Pad 8 95045 T/D Seal Anvil 9 94874 Side Plate 0 94875 Side Plate 2 94872 M/D Seal Pad 2 95046 M/D Seal Anvil 3 94870 Side Plate Table -4: L-26 Seal Bar Assembly Standard.6 L-26 Seal Bar Assembly Standard (XXXXX) -33
.7 L-26 Seal Bar Assembly Blacksparkle - Polyolefin (26589) Black Speckle Seal Bar Used on Sticky Polyolefin & Sticky Polyethylene Film with Wide Seal Flow Direction Blade (M/D) Tranverse Direction Blade (T/D) 7 3 8 9 2 3 5 5 0 0 4 6 5 2 4 6 Figure -3. L-26 Seal Bar Assembly Blacksparkle - Polyolefin -34.7 L-26 Seal Bar Assembly Blacksparkle - Polyolefin (26589)
Fig ref. Part number Description Qty 2372-026 Blade, Knife, 22.047, Bar, Seal, Coated 2 204034 Halves, Bar, Seal, 560MM, T/D, L26 3 8755 Heater, Cartridge, T/D 4 8754 Heater, Cartridge, M/D 5 204036-00 Blade, Knife, Bar, Seal, M/D, 0Z, Blacksparkle Coated 6 204035 Halves, Bar, Seal, 495MM, M/D, L8 7 9487 T/D Seal Pad 8 95045 T/D Seal Anvil 9 94874 Side Plate 0 94875 Side Plate 2 94872 M/D Seal Pad 2 95046 M/D Seal Anvil 3 94870 Side Plate 4 204037-000A Insert, Bar, Seal, Plasma, T/D, Notched 5 073-028 Insert, Bar, Seal, Plasma, 560mm Long 6 239082 Inserts, Bar, Seal, Plasma, M/D (Set) Table -5: L-26 Seal Bar Assembly Blacksparkle Polyolefin.7 L-26 Seal Bar Assembly Blacksparkle - Polyolefin (26589) -35
.8 L-26 Seal Bar Assembly Mushroom Radius Corner - Polyolefin, PVC (26590) Mushroom Radius Corner Blade Set Used on Polyethylene Film with Narrow Width Seal & a Tight Square Corner Typical Mushroom Inserts and Blades 5 7 6 4 4, 2 2 8 8 3 5,3 9 0 Figure -4. L-26 Seal Bar Assembly Mushroom Radius - Polyolefin, PVC -36.8 L-26 Seal Bar Assembly Mushroom Radius Corner - Polyolefin, PVC (26590)
Fig ref. Part number Description Qty 8255 Blade, Cutting, Front, Arrow, Bar, Seal L26 2 8755 Heater, Cartridge, T/D (30Z) 3 8754 Heater, Cartridge, M/D (30 Z) 4 8255-00 Blade, Cutting, Cross, Arrow, Bar, Seal L26 5 9487 T/D Seal Pad 6 65045 T/D Seal Anvil 7 94874 Side Plate 8 94875 Side Plate 2 9 94872 M/D Seal Pad 0 95046 M/D Seal Anvil 94870 Side Plate 2 82550-00 Insert, Cross, Arrow, Bar, Seal 3 82550 Insert, Front, Arrow, Bar, Seal 4 9540 T/D Seal Blade Insert 5 954 M/D Seal Bar Body, Set Table -6: L-26 Seal Bar Assembly Mushroom Radius Corner.8 L-26 Seal Bar Assembly Mushroom Radius Corner - Polyolefin, PVC (26590) -37
.9 L-26 Seal Bar Assembly Mushroom Straight Corner - Polyolefin, PVC (2659) Mushroom Square Corner Blade Set Used on Polyethylene Film with Narrow Width Seal Typical Mushroom Inserts and Blades 5 7 6 4 4, 2 2 8 8 3 5,3 9 0 Figure -5. L-26 Seal Bar Assembly Straight Corner - Polyolefin, PVC -38.9 L-26 Seal Bar Assembly Mushroom Straight Corner - Polyolefin, PVC (2659)
Fig ref. Part number Description Qty 82559 Blade, Cutting, Front, Arrow, Bar, Seal L26 2 8755 Heater, Cartridge, T/D (30Z) 3 8754 Heater, Cartridge, M/D (30 Z) 4 82559-00 Blade, Cutting, Cross, Arrow, Bar, Seal L26 5 9487 T/D Seal Pad 6 65045 T/D Seal Anvil 7 94874 Side Plate 8 94875 Side Plate 2 9 94872 M/D Seal Pad 0 95046 M/D Seal Anvil 94870 Side Plate 2 82558-00 Insert, Cross, Arrow, Bar, Seal 3 82558 Insert, Front, Arrow, Bar, Seal 4 9540 T/D Seal Blade Insert 5 954 M/D Seal Bar Body, Set Table -7: L-26 Seal Bar Assembly Mushroom Straight Corner.9 L-26 Seal Bar Assembly Mushroom Straight Corner - Polyolefin, PVC (2659) -39
.20 L-26 Seal Bar Assembly Plasma - Polyethelyne Polyolefin, PVC (26592) Plasma Seal Bar Used on Non-Stick Polyolefin & Polyethylene Film with Wide Seal Flow Direction Blade (M/D) Tranverse Direction Blade (T/D) 7 3 8 9 2 3 5 5 0 0 4 6 5 2 4 6 Figure -6. L-26 Seal Bar Assembly Plasma - Polyethelyne, Polyolefin, PVC -40.20 L-26 Seal Bar Assembly Plasma - Polyethelyne Polyolefin, PVC (26592)
Fig ref. Part number Description Qty 047-028 Blade, Knife, Bar, Seal, T/D 560mm Lg 30z 2 204034 Halves, Bar, Seal, 560MM, T/D, L26 3 8755 Heater, Cartridge, T/D 4 8754 Heater, Cartridge, M/D 5 204036 Blade, Knife, Bar, Seal, M/D 560mm Lg 30z 6 204035 Halves, Bar, Seal, 495MM, M/D, L8 7 9487 T/D Seal Pad 8 95045 T/D Seal Anvil 9 94874 Side Plate 0 94875 Side Plate 2 94872 M/D Seal Pad 2 95046 M/D Seal Anvil 3 94870 Side Plate 4 204037-000A Insert, Bar, Seal, Plasma, T/D, Notched 5 073-028 Insert, Bar, Seal, Plasma, T/D 6 239082 Inserts, Bar, Seal, Plasma, M/D (Set) Table -8: L-26 Seal Bar Assembly Plasma.20 L-26 Seal Bar Assembly Plasma - Polyethelyne Polyolefin, PVC (26592) -4
.2 Seal Head Frame Assembly 2 49 47 6 Lower Chain Both Sides 7 5 3 (Upper Chain Both Sides) 23 22 48 6 4 8 9 4 20 2 42 43 2 20 7 (Block) 3 (Bearing) 9 (Block) 3 (Bearing) 4 2 (Block) 3 (Bearing) 5 (Block) 3 (Bearing) 0 24 4 29 6 8 9 8 27 28 45 46 25 26 40 44 20 2 34 36 35 4 33 30 32 3 37 39 38 Figure -7. Seal Head Frame Assembly -42.2 Seal Head Frame Assembly
Fig ref. L-8 P/N L-26 P/N Description Qty 94773 94773 Plate 2 2 94772 94880 Polished Shaft 2 3 94782 94877 Chain 2 4 94775 94775 Stud 4 5 94774 94774 Block 4 6 9478 94876 Chain 2 7 9570 9594 Side Frame, Rear 8 9477 9477 Stud, Idler 2 9 94770 94770 Sprocket, Idler 2 0 9498 9505 Screw 94776 94878 Shaft 2 9500 9542 Guide Block, Top Rear 3 87087 87087 Linear Bearing 8 4 94978 94978 Block 5 95097 9545 Guide Block, Top Front 6 94779 94779 Bushing 2 7 95099 9543 Guide Block, Bottom Rear 8 94986 94986 Mounting Block 9 95098 9544 Guide Block, Bottom Front 20 87092 87092 Bushing 4 2 94985 94985 Bushing Housing 4 22 9569 9593 Bottom Frame 23 94769 94769 Sensor Bracket 24 950 9546 Top Frame 25 94777 94777 Sprocket 2 26 87094 87094 Bearing 2 27 94778 94778 Pointer 28 94793 94793 Ruler 29 957 9595 Side Frame, Front 30 94984 94984 Plate 3 8709 8709 Thrust Bearing 2 32 94780 94780 Nut 33 87093 87093 Bushing 34 94987 94987 Bearing Housing 35 87089 8764 Chain 36 87083 87083 Sprocket 37 87086 87086 Crank Handle Table -9: Seal Head Frame Assembly.2 Seal Head Frame Assembly -43
Fig ref. L-8 P/N L-26 P/N Description Qty 38 94980 94980 Shaft 39 94979 94979 Bearing Housing 40 87085 87085 Sprocket 4 87052 87052 Bearing, NSK 6902Z 6 42 94895 94895 Slide Bracket 43 97099 97099 Reed Switch 44 94825 94825 Mounting Bracket 45 876 876 Proximity Switch 46 94860 94860 Bar Nut 47 9703 9703 Box; Junction 48 94898 94898 Bracket; Mounting 49 94899 94899 Cover Table -9: Seal Head Frame Assembly -44.2 Seal Head Frame Assembly
Page Intentionally Blank.2 Seal Head Frame Assembly -45
.22 Film Unwind Assembly 3 2 67 63 7 64 65 45 9 4 8 7 8 9 3 9 8 7 0 6 5 4 20 5 68 4 4 69 3 2 70 56 45 55 3 9 62 57 24 8 25 28 26 27 29 30 58 66 60 59 22 6 37 36 34 3 39 40 38 33 23 35 42 43 32 3 44 46 47 48 52 50 5 49 54 53 Figure -8. Film Unwind Assembly -46.22 Film Unwind Assembly
Fig ref. L-8 P/N L-26 P/N Description Qty 94883 94854 Shaft, Film Cradle Roller 2 94642 94855 Rod 3 9466 94856 Roll, Idler 4 4 95054 95033 Roller Film Cradle W/Out Grooves 5 95053 95034 Roller Film Cradle W/Grooves 6 94940 95035 Film Drive Roller 7 94659 94857 Shaft, Idler Roll 2 8 94662 94662 Bushings 8 9 87053 87053 Snap Ring 0 0 87054 87054 Snap Ring 6 94665 94665 Bushing 3 2 9556 9556 Cover 3 9552 9582 Support Bracket 4 87062 8799 Hand Knob 2 5 87064 87064 Bearing, 2 Hole Frange 2 7 94646 94646 Bracket 2 8 87052 87052 Bearing 2 9 94653 94858 Shaft, Roller, Film Pinch 20 94672 94672 Perf, Wheel, Dual O Ring Style 4 2 87065 87065 Pin (P/O Item 00200) 20 22 95059 95059 Bracket 23 94935 94935 Bracket, Dancer Collar 24 94666 94666 Static Discharge Point 2 25 94675 94859 Rod 26 94643 94643 Shaft; Weight 27 94937 94937 Film Guide 28 9464 9464 Weight 29 94640 9486 Pivot, Shaft Dancer 30 94650 94650 Stud 3 94668 94668 Housing 2 32 94667 94667 Cam 33 94656 94862 Shaft, Dancer Roll 34 94906 94864 Film Separator 35 94655 94865 Shaft, Idler Roll 36 9563 9583 Static Eliminator Brush 37 95079 95079 Bracket 38 9554 9584 Guard Table -20: Film Unwind Assembly.22 Film Unwind Assembly -47
Fig ref. L-8 P/N L-26 P/N Description Qty 39 9465 94866 Roller, Film Pinch 40 94647 94647 Spring Fixture 4 94645 94867 Pivot Shaft 42 94669 94669 Spring Adjustment Bolt 43 94673 94673 Release Lever 44 94677 94677 Cam 45 94924 94924 Nut Plate 2 46 87060 87060 Spring 47 94644 94644 Nut Washer 48 94676 94676 Bearing 49 87058 87058 Knob 50 94938 94938 Handle 5 94689 94689 Sprocket 52 9560 9560 Cover 53 8706 8706 Chain 54 94690 8730 Sprocket 55 9559 9587 Support Bracket 56 8703 8703 Gear Motor 58 8739 8739 Switch, Roller Plunger 59 95060 95060 Plate; Collar Retaining 60 94904 94904 Collar; Rod Retainer (Center) 6 94905 94905 Collar; Rod Retainer (Outer) 2 62 95068 95068 Bracket; Dancer Collar W/90 Bend 63 94909 94909 Brake; Leather 64 9490 9490 Bracket; Spring Retaining 65 949 949 Bracket, Leather Retaining 66 94907 94907 Bracket; Brake Mounting 67 9493 9493 Bushing; Brake Collar 68 9492 9492 Collar; Brake 69 95066 95066 Shaft 70 9494 9494 Bushing; Film Cradle Roller 7 8790 8790 Spring; Extension Table -20: Film Unwind Assembly -48.22 Film Unwind Assembly
Page Intentionally Blank.22 Film Unwind Assembly -49
.23 Take Away Assembly 2 3 2 44 8 42 43 4 4 33 7 0 2 40 38 39 37 6 46 47 5 34 34 6 5 9 4 3 5 9 34 7 30 45 8 32 29 3 9 20 28 35 26 2 23 36 27 22 24 25 Figure -9. Take Away Assembly -50.23 Take Away Assembly
Fig ref. L-8 P/N L-26 P/N Description Qty 87063 87063 Gearmotor 2 94708 94708 Nut Plate 2 3 94949 94949 Bracket, Motor Mount 4 94737 94737 Sprocket 5 94686 94686 Stud 3 6 94684 94684 Idler Pulley, Flanged 7 87068 87068 Bearing, Ashi Flange 2 8 94736 94736 Sprocket 9 94687 94687 Idler Pulley, Smooth 6 0 94697 94697 Shaft 94740 94740 Drive Pulley, Htd Timing Belt 2 2 9596 9596 Bracket, Drive Shaft Mounting 3 94679 94679 Nut Plate 4 9502 9548 Pressure Plate 5 9509 9547 Take-Away Bracket 6 94936 94936 Scrap Finger 7 94682 94682 Stud 4 8 9476 9476 Lower Pinch Roller 9 94683 94683 Open Gear 2 20 94972-94972 Block 000A 2 94678 94678 Pin 22 94788 94788 Guard 23 87059 87059 Spring Compression 2 24 94750 94750 Washer 2 25 94768 94768 Block 26 94745 94745 Knob 27 94989 94989 Guard 28 94748 94748 Screw 2 29 9474-000A 9474-000A Pulley, Htd Timing Belt 30 94694 94694 Upper Pinch Roller 3 87066 8753 Upper Belt, 465 J 32 87067 87078 Lower Belt, 353 J 33 9474 9474 Chain, Roller RS35 34 87065 87065 Bearing, NSK 6800 Z 4 35 8747 8747 Bushing, Garlock MB22DO 2 36 8744 8744 Bearing, NSK 690Z 4 Table -2: Take Away Assembly.23 Take Away Assembly -5
Fig ref. L-8 P/N L-26 P/N Description Qty 37 9480 9480 Stud 38 94803 94803 Roller 39 94800 94800 Hub 40 94802 94802 Hub 4 9492 9492 Standoff 42 94922 94922 Mounting Bracket 43 8796 8796 Rotary Encoder 44 82907 82907 Shaft Coupling 45 95069 95069 Idler Mounting Bracket 46 87057 87057 Wing Nut 47 9507 95063 Plate; Upper Pressure Table -2: Take Away Assembly -52.23 Take Away Assembly
Page Intentionally Blank.23 Take Away Assembly -53
.24 Outfeed Apron Assembly 6 8 4 5 3 3 30 35 34 9 6 8 7 2 0 35 34 5 4 7 8 2 0 9 6 33 8 32 3 9 20 9 28 2 3 27 23 25 26 24 29 22 Figure -20. Outfeed Apron Assembly -54.24 Outfeed Apron Assembly
Fig ref. L-8 P/N L-26 P/N Description Qty 9507 952 Plate, W/Tape 2 94990 94990 Guard 2 3 94746 94746 Bracket 2 4 94797-9488 Shaft 000A 5 94794 94820 Roller 2 6 9476 9476 Collar 2 7 94743 94822 Shaft 9 94730 94730 Block 2 0 87094 87094 Bearing 2 87085 87085 Sprocket 2 2 94958 9507 Roll, Rubber 3 26278-00 26278-004 Roller 6 4 9479 94824 Shaft 6 6 24309-00 94956 Bracket 7 24309-002 94977 Bracket 8 94747 94747 Spacer 2 9 94708 94708 Nut Plate 2 20 87063 87063 Motor 2 9573 9577 Frame 22 94955 9508 Bracket 23 9473 9473 Roll Bracket 24 94728 94728 Stud 2 25 94723 94827 Shaft 26 94727 94829 Tube; Nose Roller 27 94725 9483 Bar 28 94744 94744 Roller Bracket 29A 827038-00 827003 Conveyor Belt Green Rough Top - Dry Ice 29B 8767-00 8780 Conveyor Belt White Smooth Top (Food Grade) 29C 87097 8758 Conveyor Belt Green Smooth Top 30 220075 220075 Chain Table -22: Outfeed Conveyor Assembly.24 Outfeed Apron Assembly -55
.25 Outfeed Slide Conveyor 7 8 4 2 6 45 7 9 3 46 8 2 20 3 4 45 46 28 2 3 9 0 32 28 38 39 48 44 3 42 4 22 8 29 30 3 33 35 43 27 23 5 38 40 5 45 46 25 4 26 24 Figure -2. Outfeed Slide Conveyor -56.25 Outfeed Slide Conveyor
Fig ref. L-8 P/N L-26 P/N Description Qty 9575 22290 Frame 2 94995 9530 Bed Plate 3 952 9528 Slide Bed 4 94997 95029 Cross Member 5A 827039 827040 Conveyor Belt Green Rough Top - Dry Ice 5B 8767-002 82704 Conveyor Belt White Smooth Top (Food Grade) 5C 8748 8763 Conveyor Belt Green Smooth Top 6 94990 94990 Guard 7 220075 220075 Chain 8 94993 95030 Guide 9 94730 94730 Block 2 0 9476 9476 Collar 2 8788 8788 Tensioner Bolt & Washer 2 2 94743 22295 Tension Roller Shaft 3 94795 9489 Roller Tube 5 4 94797-9486 Roller Shaft 3 000A 5 94806 94849 Roller Shaft 6 94958 22300 Drive Roller 7 87094 87094 Bearing 2 8 87085 87085 Sprocket 2 9 87063 87063 Motor 20 8787 8787 Junction Box 2 94708 94708 Nut Plate 2 22 94746 94746 Mounting Foot 2 23 94726 94829 Nose Roller Tube 24 94729 94729 Bushing 2 25 94723 94826 Roller Shaft 26 94807 94807 Bracket 27 94808 94808 Bracket 28 87099 87099 Magnetic Reed Switch 29 8749 8749 Air Cylinder 30 874 874 Solenoid Valve (24VDC) 2 3A 8789 8789 Flow Restrictor 2 3B 873 873 Solenoid Valve with Bypass Switch 2 32 8757 8757 Air Tubing 2 ft. Table -23: Outfeed Slide Conveyor.25 Outfeed Slide Conveyor -57
Fig ref. L-8 P/N L-26 P/N Description Qty 33 94999 95057 Cross Member 34 95000 95073 Bracket Cross Member 35 94809 94885 Linear Shaft 2 36 9480 9480 Stroker Limiter 37 9500 9500 Threaded Rod 38 8773 8773 Bushing Housing Only SFPBE-2 2 39 8774 8774 Bushing FL-2 40 8750 8750 Bushing; Compensating FLC-2 4 95003 95003 Carriage Side Plate Front 42 95023 95023 Carriage Side Plate Rear 43 94886 94886 Coupling; Cylinder M/F 44 95055 95058 Bracket Cross Member 45 8744 8744 Bearing 0 46 8770 8770 External Snap Ring 8 47 8756 8756 Straight Air Fitting Manifold (NS) 2 48 8772art number 8772 Floating Joint Coupling Table -23: Outfeed Slide Conveyor -58.25 Outfeed Slide Conveyor
Page Intentionally Blank.25 Outfeed Slide Conveyor -59
.26 Electrical Components (Part ) 2 3 4 5 6 7 8 7,8 6 4,5 2,3 0 9 9,20 2 22 23 26 25 24 Figure -22. Electrical Components (Part ) -60.26 Electrical Components (Part )
Fig ref. Part number Description Qty 8734 Solid State Relay, Omron G3NA-20B5 2 2 804000-005 Circuit Breaker, Allen-Bradley 492-5 CBG050 277V 5 A 3 804000-30 Circuit Breaker, Allen-Bradley 492-2 CB2G030 480V 3A 4 804000-07 Circuit Breaker, Allen-Bradley 492- CB2G050 480V 5A 5 804000-003 Circuit Breaker, Allen-Bradley 2 492CBG030 277V 3A 6 8727 Adjustable Frequency Motor Controller Inverter, Mistubishi FREQROL-E500-FR- E520S-0. K 4 7 8737 Power Supply, Omron S82J-0024 8 876 Main Circuit Breaker, 5 Amp, Square D QOU25, 2P 5A 9 804023-026 Thermocouple Converter, ABB 2 SVR0753R2000 0 8728 Potentiometer, P2 8743 Adjustable Frequency Motor Controller Inverter, Mistubishi SC-A200U 2 804008.069 Relay, Allen-Bradley 700-HK32A-4 2 3 804008-070 Relay, Socket, Allen-Bradley 700-HN22 2 4 804002.044 Master Control Relay Allen-Bradley 00- C23ZJ0 23A 5 804035.002 Contact, Aux. Allen-Bradley 00-FA20 6 804005.89 Analog Output, Microlux 200, Allen-Braley 762-IF20F2 7 804005.88 PLC, Allen-Bradley Microlux 200 8 804005.90 PLC Memory Cartridge, Allen-Bradley 762-MM 9 80408.056 Operator Interface, EXOR ETOP 20 804003.08 Cable, Communication, Exor CA95-20 2 8723 Pushbutton Switch, Fuji AR22FOR-0G 22 8722 Pushbutton Switch, Fuji AR22V2L E3 23 8725 Pushbutton Switch, Fuji AR22FOR-0W 24 8705 Pushbutton Switch, Fuji AR22FOL 25 872 Pushbutton Switch, Fuji AR22FOR-0G 26 8723 Pushbutton Switch, Fuji AR22FOR-0G Table -24: Electrical Components (Part ).26 Electrical Components (Part ) -6
.27 Electrical Components (Part 2) 2 3 5 2 6 4 6 9 7 8 Figure -23. Electrical Components (Part 2) -62.27 Electrical Components (Part 2)
Fig ref. L8 P/N L26 P/N Description Qty 8702 8702 Magnetic Door Switch Omron GLS-S 2 2 8739 8739 Roller Plunger Switch OHM Z-5G022B 2 3 804007.33 804007.33 Photosensor, Transmitter, Allen-Bradley 42EF-EEZB-F4 4 80400.34 80400.34 Photosensor, Reciever Allen-Bradley 42EF-R9MPBV-F4 5 87099 87099 Reed Switch, SMC D-H7BL 2 6 87076 87076 Thermocouple, Watlow 46-00007 2 7 8738 8738 Proximity Switch, Omron TL-W5MD2 2 8 87077 8754 Cartridge Heater, Side Seal 9 87075 8755 Cartridge Heater, Cross Seal 0 8796 8796 Rotary Encoder, Omron E6A2-CS5C (Not Shown) Table -25: Electrical Components (Part 2).27 Electrical Components (Part 2) -63
.28 Electrical Components (Options) (Part 3) 2 3 4 Figure -24. Electrical Components (Part 3) Fig ref. Part number Description Qty 80407.042 Light Stack, Red, Allen-Bradley 855T- B24DN4 2 80407.037 Light Stack, Amber, Allen-Bradley 855T- B24DN5 3 80407.043 Light Stack, Green, Allen-Bradley 855T- B24DN3 4 80407.025 Stack Light Base, Allen-Bradley 855T- BPM25C 5 804007.5 Photo Sensor, Low Film Alert, Allen-Bradley 42BT-BLBSN (Not Shown) Table -26: Electrical Components (Part 3) -64.28 Electrical Components (Options) (Part 3)
.29 Pneumatics Components,2 3 4 5 7 6 3 0 8,9 2A,2B Figure -25. Pneumatic Components Fig ref. Part number Description Qty 877 Air Filter/Regulator Assembly, SMC AW30-03-GH-W 2 877-00 Air Filter Element, SMC AF30P-060S 3 874 Solenoid Valve, SMC VP542-5DZ-03AF 4 870 Solenoid Valve, SMC VT325-025 DLS 5 873 Solenoid Valve, SMC VFR20-5DZC 6 80304 Check Valve, Aladco 30250 7 8744 Solenoid Valve 8 8768 Air Manifold 9 8777 Air Manifold 2 0 8789 Flow Control Valves 2 8778 Shut Off Valve 2A 8040 Air Regulator 2B 804 Air Gage 3 8766 Cushion Speed Control Table -27: Pneumatic Components.29 Pneumatics Components -65
.30 6 Lugged Infeed Conveyor Core (Option) [22793] 20 7 23 27 9 22 2 3 3 8 24 6 7 4 9 5 6 5 8 2 4 4 26 2 0 Figure -26. 6 Lugged Infeed Conveyor Core (Option) -66.30 6 Lugged Infeed Conveyor Core (Option) [22793]
Fig ref. Part number Description Qty 36658 Sprocket 2 42233 Shaft, Idler 3 42997.00 Cam, Chain, Head 4 4434.002A Block, Takeup 2 5 44200.002A Cover, Lug 6 4446.00 Cam, Tail, Chain, LH 7 8687 Motor, Gear, /2 HP Kebco 8 46858.000A Sprocket 2 9 68603 Block, Takeup 2 0 69546 Cover, End, SS 69546.00 Cover, End, SS 2 72435 Cam, Tail, Chain, RH 3 9350.00 Plate, Nut 2 4 9425 Channel, Conveyor, L.H. 5 9426 Channel, Conveyor, R.H. 6 9427 Plate, Spacer, Motor 7 9428 XBar, Support, Rail 3 8 9429 Rail, Chain, 6 9 9430 Bracket, Support, Plate, Top 20 943 Shaft, Drive, Conveyor 2 9432 Sprocket 22 9433 Bracket, Switch 23 9439.00 X-Brace 2 24 873 Torque Limiter, Helland Zero Max 25 800466 Chain, Roller #40 Roller 2 26 802782 Bearing, Flange ID 4 27 9430.00 Bracket, Support, Plate, Top Table -28: 6 Lugged Infeed Conveyor Core (Option).30 6 Lugged Infeed Conveyor Core (Option) [22793] -67
.3 480VAC Conversion Kit (Option) 2 A, B Figure -27. 480V Conversion Kit (Option) Fig ref. Part number Description Qty A 804024.004 Transformer (240-480 VAC) B 804024-006 Transformer (208-240 VAC) 2 22796 Transformer Mounting Plate Table -29: 480V Conversion (Option) -68.3 480VAC Conversion Kit (Option)
.32 Lower Film Cradle (Option) [97355] 2 5,6,7 4 3 Figure -28. Lower Film Cradle (Option) Fig ref. L-8 P/N L-26 P/N Description Qty 96223 96223 Bracket, Idler Roller Mounting RH 2 96224 96224 Bracket, Idler Roller Mounting LH 3 979 979 Bracket, Film Frame 4 9720 9720 Bracker, Film Frame 5 95769 94857 Shaft, Idler Roller 2 6 95770 94856 Roller, Idler 2 7 94662 94662 Bushing 4 Table -30: Lower Film Cradle (Option).32 Lower Film Cradle (Option) [97355] -69
.33 Auxiliary Emergency Stop Button (Option) [94576] 0 2 7 8 6 Figure -29. Auxiliary Emergency Stop Button (Option) Fig ref. Part number Description Qty 95267 Infeed E-Stop Mount 2 87464 Button, Operator 3 87465 Block, 4 Across Latch 4 87466 Contact, N/C 3 5 87467 Contact, N/O 6 87468 Operator Enclosure 7 804027.003 Legend Plate, Blank Standard Red 8 8835 T & B Conn. /2 X.25 2 9 8040.089 Conduit, Locknut (Not Shown) 0 88695 Wire, 8 Conductor 2 Table -3: Auxiliary Stop Button (Option) -70.33 Auxiliary Emergency Stop Button (Option) [94576]
.34 Auxiliary Infeed/Discharge Conveyor Control Relay (Option) [97362.000A] Note: This option is used for conveyors not provided by Arpac. 3 2 Figure -30. Auxiliary Infeed Control Relay (Option) Fig ref. Part number Description Qty 804008.06 Relay, Extra Slim 2 87482 Cable 6 3 80400.2 Connector 7 Table -32: Auxiliary Infeed Control Relay (Option).34 Auxiliary Infeed/Discharge Conveyor Control Relay (Option) [97362.000A] -7
.35 Vertical Photoeye (Option) [94595] 3 4 4 2 7 7 5 0 3 7 4 7 5 7 6 Figure -3. Vertical Photoeye (Option) Fig ref. Part number Description Qty 95268 Vertical Eye Mount, Lower 2 95269 Vertical Eye Mount, Upper 3 95270 Vertical Eye Mount, Nut Plate 4 9527 Vertical Eye Mount, Angle 5 8735 Photo Sensor, Transmitter DC 6 804007 Photo Sensor, Receiver, DC 7 804003.35 Cable 2 8 87493 Terminal Wire Nut 4 9 80400.2 Connector, Terminal, Fork 4 0 803444 Tie, Cable 6 97308 Hardware for Vertical Eye Kit 2 8272 Splice, Nylon, Insulated 4 3 804039.068 Wire, Cable Tie Cross Section 8 4 807798.02 Hex Head Cap Screw, M4 x 0.7 x 2mm 4 5 80780.00 Washer, Flat, M4 6 6 89486.00 Screw, Thumb, M4 x 0.7 x 2 2 7 807800.00 Washer, Lock, Split M4 6 Table -33: Vertical Photoeye (Option) -72.35 Vertical Photoeye (Option) [94595]
.36 Pneumatic Hole Punch (Option) [97340] 2 8 7 4 0 6 5 4 Figure -32. Pneumatic Hole Punch (Option) Fig ref. L-8 P/N L-26 P/N Description Qty 9629 9629 Mounting Plate (RH) 2 96925 96925 Mounting Plate (LH) 3 95385 95385 Bar Nut, M* 2 3/4 Centers 2 4 96926 96920 Tube, Hole Punch 5 95386 95386 Spacer Dia x 5/6 Thick 2 6 96927 9699 Bar, Hole Punch 7 95374 95374 Spacer, Hole Punch Cylinder 8 8763 8763 Cylinder, Hole Punch Bimba 840-A 9 878 878 Valve, Solenoid, Hole Punch 0 8299 8299 Tubing, 5/6 O.D. Clear 5 87839 87839 Tube Fitting, 90 Deg. Elbow, 8mm 3 2 87838 87838 Fitting, Plug In Reducer 3 87837 87837 Tube Fitting, 0mm Union Tee 4 8799 8799 Knob, Bolt M8 x.25 Stud x 20mm 2 5 80780.003 80780.003 Washer, Flat, M8 6 6 822727 822727 Socket Head Cap Screw, M8 x 40mm 2 7 822728 822728 Button Head Cap Screw 4 8 822729 822729 Washer, Lock, M8 8 Table -34: Pneumatic Hole Punch (Option).36 Pneumatic Hole Punch (Option) [97340] -73
.37 Infeed Product Guide (Option) [94572] 3 or 4 6 7, 8 5 2 Figure -33. Infeed Product Guide (Option) Fig ref. Part number Description Qty 9564.00 Clamp Plate, SS 2 96222.00 Bracket, Guide, Product, SS 3 9688 Product Guide 4 97357 Product Guide (for Reverse Flow Machines Only) 5 800346.002 Screw, Set, M8 x 2mm 2 6 800278.020 Hex Head Cap Screw, /4-20 x 2 3/4 SS 4 7 800292.008 Washer, Lock, Split /4 SS 4 8 800290.009 Nut, /4-20 Hex SS 4 Table -35: Infeed Product Guide (Option) -74.37 Infeed Product Guide (Option) [94572]
.38 Seal Opening Kit (Option) 2 3 4 Fig ref. L-8 P/N 8 Figure -34. Seal Opening Kit (Option) L-26 P/N 0 Description 95633 95633 Spacer, Seal Height Crank 2 2 95634 95634 Spacer, Seal Height Jack Screw 2 3 96069 96069 Cylinder Block 4 8762 8769 Seal Head Cylinder 5 807798-024 807798-024 Hex Head Cap Screw M6 X X 60mm 4 Table -36: Seal Opening Kit (Option) Qty.38 Seal Opening Kit (Option) -75
.39 Stack Light (Option) [94578] 2 3 4 5 Figure -35. Stack Light (Option) Fig ref. Part number Description Qty 80407.042 Light Stack, Red, Allen-Bradley 855T- B24DN4 2 80407.037 Light Stack, Amber, Allen-Bradley 855T- B24DN5 3 80407.043 Light Stack, Green, Allen-Bradley 855T- B24DN3 4 80407.025 Stack Light Base, Allen-Bradley 855T- BPM25C Table -37: Stack Light (Option) -76.39 Stack Light (Option) [94578]
.40 Registration Kit (Option) [94575] Fig ref. Part number Description Qty 95692 Bracket, Print Reg. Eye Mounting 2 2 95709 Strip, Nut, Print Reg. Eye 3 9570 Bracket, Print Reg. 4 957 Shaft, Print Reg. Eye 5 8738 Adj. Handle, Stud Type /4-20 x 3/4 3 6 804007-49 Photo Sensor, Registration 7 804003-35 Cable, Registration Table -38: Registration Kit (Option) 6 3 4 7 5 Figure -36. Registration Kit.40 Registration Kit (Option) [94575] -77
-78