INSTALLATION INSTRUCTIONS Accessory Application 2008 ACCORD 2-DOOR Publications No. AII 37561-38377 Issue Date NOV 2007 PARTS LIST Control unit bracket (L4) Back-up Sensor Attachment Kit P/N 08V67-TE0-100A Control unit Control unit bracket (V6) Beeper 13 Wire ties 4 Sensor clips Wire tie with clip Back-up sensor harness 2 Wire ties with holder Back-up sensor subharness 2 Urethane tapes Fuse label 2007 American Honda Motor Co., Inc. All Rights Reserved. AII 37561-38377 (0711) 08V67-TE0-1000-91 1 of 15
Flange bolt, 6 x 12 mm Flange nut 4 Harness tapes Accessory User s Information Manual TOOLS AND SUPPLIES REQUIRED Phillips screwdriver Flat-tip screwdriver Ratchet 8 mm and 10 mm Socket Pushpin Drill 3 mm Drill bit 24 mm and 26 mm Hole saw Ruler Eye protection (safety goggles, face shield, etc.) 10 mm Combination wrench File Trim tool TN SILTRIMTL10 Illustration of the Back-up Sensor Installed on the Vehicle BUZZER Back-up Sensor Kit P/N 08V67-TE0-100K 2 Center sensors 2A FUSE CASE (Blue) 2 Corner sensors LEFT (WHITE) LEFT CENTER (BLUE) RIGHT CENTER (BLUE) RIGHT (WHITE) 742308AE (White) INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. 1. Make sure you have the anti-theft code for the radio and navigation system (if equipped), then write down the radio presets. 2 of 15 AII 37561-38377 (0711) 2007 American Honda Motor Co., Inc. All Rights Reserved.
2. Disconnect the negative cable from the battery. 3. Remove the two covers from the rear bumper and remove the rear bumper (two bolts, six self-tapping screws, two clips, and unplug one connector). NOTE: Have an assistant help you remove the rear bumper. 5. Remove the rear trim panel (five clips and three hooks). 4 S REAR TRIM PANEL 2 BOLTS 3 HOOKS 2 COVERS 2 S 6 SELF-TAPPING SCREWS REAR BUMPER 742003CB 6. Fold down the rear seat back by pulling the lever under the rear shelf inside the trunk. REAR SEAT BACK REAR SHELF 4. Remove the trunk floor mat (one clips). TRUNK FLOOR MAT 7. Remove the left trunk side lining (five clips). LEFT TRUNK SIDE LINING 2 S 3 S LEVER (Pull.) 742416BE 2007 American Honda Motor Co., Inc. All Rights Reserved. AII 37561-38377 (0711) 3 of 15
8. Using the trim tool, remove the rear shelf access panel, then release the front rear speaker retaining tab. 10. Remove the left rear speaker (one bolt and disconnect the vehicle connector). BOLT LEFT REAR SPEAKER REAR SHELF ACCESS PANEL LEFT REAR SPEAKER COVER 7115040E TRIM TOOL (TN SILRIMTL10) 11. Wrap urethane tape around the control unit at the area shown. Then, attach the control unit bracket into the control unit. 9. Remove the left rear speaker cover (nine retaining tabs). L4 MODEL URETHANE TAPE LEFT REAR SPEAKER COVER 9 RETAINING TABS BRACKET V6 MODEL URETHANE TAPE BRACKET 742418AE 761205CE 4 of 15 AII 37561-38377 (0711) 2007 American Honda Motor Co., Inc. All Rights Reserved.
L4 Model 12. Install the control unit to the vehicle panel: Partially thread the 6 mm flange nut onto the control unit bracket stud. Insert the control unit bracket stud into the hole in the vehicle panel. Tighten the 6 mm flange nut to secure the bracket to the vehicle panel. V6 MODEL Loosen the upper bolt from the relay support. Remove the relay support (one bolt and disconnect the vehicle connectors). PANEL BOLT (Loosen.) PANEL HOLE 6 mm FLANGE NUT BRACKET STUD BOLT S RELAY SUPPORT BOLT (Remove.) 771101AB Install the control unit bracket to the relay support using the 6 x 12 mm flange bolt and the 6 mm flange nut. STUD BOLT HOOK BRACKET 742311CE BRACKET STOPPER RELAY SUPPORT 6 mm FLANGE NUT 6 x 12 mm FLANGE BOLT RELAY SUPPORT 771102BB Reinstall the relay support. 2007 American Honda Motor Co., Inc. All Rights Reserved. AII 37561-38377 (0711) 5 of 15
13. Attach the 2A fuse label to the fuse case on the back-up sensor harness. 14. Disconnect the back-up light 2-pin connector from the left taillight, and plug it into the back-up sensor harness 2-pin connector. Plug the remaining back-up sensor harness 2-pin connector into the left taillight. FUSE CASE LEFT TAILLIGHT LIGHT 2-PIN 2-PIN 2A FUSE LABEL 742312AE TRUNK ROOM 742313BE 6 of 15 AII 37561-38377 (0711) 2007 American Honda Motor Co., Inc. All Rights Reserved.
15. At the left taillight, secure the back-up sensor harness to the vehicle harness with one wire tie. V6 MODEL GREEN TAPE 742314BE 16. Plug the back-up sensor harness 14-pin connector into the control unit, and route the harness forward along the vehicle harness. Secure the back-up sensor harness to the vehicle harness at the green tape. L4 MODEL 14-PIN WIRE TIE 761301CE WIRE TIE GREEN TAPE 14-PIN 742315DE 2007 American Honda Motor Co., Inc. All Rights Reserved. AII 37561-38377 (0711) 7 of 15
17. Secure the back-up sensor harness to the vehicle harness with two additional wire ties at the locations shown. L4 Model V6 MODEL 2 S 2 S 742401CE 771103BB 18. Secure the back-up sensor harness clip to the hole in the vehicle panel. PANEL 742402BE 8 of 15 AII 37561-38377 (0711) 2007 American Honda Motor Co., Inc. All Rights Reserved.
19. Using scissors cut one urethane tape in half, and then cut one of the halves again. Wrap the cut pieces around the beeper harness shown. 20. Install the connector clip to the beeper 2-pin connector. BEEPER 2-PIN URETHANE TAPE 23. Secure the beeper harness to the vehicle harness with one wire tie. BEEPER 2-PIN 2-PIN (Wrap from the end of the 2-pin connector.) URETHANE TAPE Wrap the urethane tapes around the harness. URETHANE TAPE (Cut in half.) BEEPER 720105BE 21. Using an isopropyl alcohol on a shop towel, clean the vehicle panel where the beeper will attach. 24. Plug the beeper 2-pin connector into the back-up sensor harness 2-pin connector. TRUNK LID HINGE BEEPER 742406CE ADHESIVE BACKING BUZZER PANEL HOLE BUZZER 2-PIN Attachment position. BUZZER 742405CE 22. Remove the adhesive backing from the beeper, and attach it to the opening in the left rear speaker at the location shown. Route the beeper harness through the hole in the rear shelf. 2-PIN URETHANE TAPE Cut in quarter 742407CE 2-PIN 25. Wrap the remaining piece of a urethane tape around the connector. 26. Secure the 2-pin connection to the vehicle harness with one wire tie. 27. Route the back-up sensor harness as shown and secure it to the vehicle harness with three wire ties. 2007 American Honda Motor Co., Inc. All Rights Reserved. AII 37561-38377 (0711) 9 of 15
S 28. Install one wire tie with clip to the holder with the fuse case, and attach the wire tie to the vehicle harness. WITH WIRE TIE FUSE CASE GROMMET 761402AE 29. Remove the vehicle grommet from the rear panel. 30. Route the back-up sensor 6-pin connector through the hole in the rear panel, and seat the harness grommet in the rear panel hole. TRUNK ROOM 742408CE 6-PIN GROMMET GROMMET Hole from which the grommet has been removed. Outside Inside 742409BE 31. Secure the back-up sensor harness to the vehicle harness with one wire tie. 10 of 15 AII 37561-38377 (0711) 2007 American Honda Motor Co., Inc. All Rights Reserved.
32. Install one wire tie with holder to the back-up sensor harness 16-pin connector, and attach the wire tie to the vehicle harness. NOTE: There are several markings on the inside of the rear bumper. Before piercing the rear bumper, verify you have the correct locations. WITH HOLDER 6-PIN REAR BUMPER 3 MARKS 3 MARKS REAR BUMPER PUSHPIN MARK REAR BUMPER PUSHPIN MARK 742603BE 742410BE 33. Mark the inside of the rear bumper: Locate the three marks on the inside of the bumper at the center and left side. Using a pushpin, pierce the rear bumper at the top and center of the three marks. Locate the three marks on the inside rear bumper on the right side. Using a pushpin, pierce the rear bumper at the bottom and the center of the right mark. 2007 American Honda Motor Co., Inc. All Rights Reserved. AII 37561-38377 (0711) 11 of 15
34. While wearing eye protection drill the rear bumper: NOTE: Center sensors are 26 mm holes, side sensors are 24 mm holes. From the outside of the bumper, drill all eight pierced marks using a 3 mm drill bit. Using a 24 mm hole saw, enlarge the lower outboard hole on the left side of the bumper. Remove all burrs. DRILL (3 mm DRILL BIT) HOLE LOWER HOLE Using 26 mm holes saw, enlarge both lower in board bumper holes at the center of the bumper. Remove all burrs. DRILL (3 mm DRILL BIT) HOLE LOWER HOLE DRILL (26 mm HOLE SAW) 24 mm HOLE SAW REAR BUMPER REAR BUMPER BURRS (Remove.) 771106AB BURRS (Remove.) 771104AB Using a 24 mm hole saw, enlarge the upper outboard hole on the left side of the bumper. Remove all burrs. 35. Install the two corner sensors into the 24 mm holes in the rear bumper using the sensor clips. Not the direction and the pin location for each sensor. 24 mm HOLE REAR BUMPER Outside Inside (White) DRILL 24 mm HOLE SAW UPPER HOLE (White) DRILL 3 mm DRILL BIT HOLE Outside Inside (White) REAR BUMPER REAR BUMPER (White) 24 mm HOLE REAR BUMPER 742412AE BURRS (Remove.) 771105AB 12 of 15 AII 37561-38377 (0711) 2007 American Honda Motor Co., Inc. All Rights Reserved.
36. Install two center sensors into the 26 mm holes in the rear bumper using the sensor clips. Note the direction and location for each sensor. 2 SUB S REAR BUMPER SUB REAR BUMPER Outside Inside 2 CENTER S (Blue) HOLDER 2 HOLES, 26 mm 742413BE WITH 2 CENTER S (Blue) 37. Plug the four back-up sensor subharness 2-pin connectors into each back-up sensor connector. NOTE: The back-up sensor harness 6-pin connector and the junction connector must be positioned on the left side of bumper. RIGHT CENTER LEFT CENTER SUB JUNCTION 742602CE 39. Secure the subharness to the bumper using four harness tapes in the locations shown. 40. Attach one wire tie with holder clip to the back-up sensor subharness junction connector and secure the wire tie to the vehicle harness. 4 SUB 2-PIN S SUB JUNCTION 6-PIN 742601BE 38. Attach the two center backup sensor subharness clips to the holes in each center sensor clip. 2007 American Honda Motor Co., Inc. All Rights Reserved. AII 37561-38377 (0711) 13 of 15
41. Using isopropyl alcohol on a shop towel, clean the area where the harness tapes will attach. 4 GREEN TAPES SUB SUB 6-PIN 6-PIN 4 TAPES LEFT CENTER RIGHT CENTER REAR BUMPER 761302AE 771107BB 42. At each green tape location, attach the back-up sensor subharness to the rear bumper with four harness tapes. 43. Plug the back-up sensor harness 6-pin connector into the back-up sensor subharness 6-pin connector, then reinstall the rear bumper.. NOTE: Have an assistant help you install the rear bumper 14 of 15 AII 37561-38377 (0711) 2007 American Honda Motor Co., Inc. All Rights Reserved.
44. Check that all wire harnesses are routed properly and that all connectors are plugged in. 45. Reinstall all removed parts. 46. Reconnect the negative cable to the battery. 47. Enter the anti-theft codes for the radio and navigation systems (if equipped), then enter the customer s radio presets. 48. Reset the clock. 49. Check that the back-up sensors work properly as described in the Accessory User s Information Manual supplied. Beeper Volume Control Factory setting of the volume control knob on the control unit is turned to maximum volume. After confirming the operation check, turn the volume control knob to the appropriate volume. VOLUME KNOB Volume up. Volume down. 771108AB 2007 American Honda Motor Co., Inc. All Rights Reserved. AII 37561-38377 (0711) 15 of 15