Pointek CLS300 - Standard Overview Configuration Installation Pointek CLS300 (standard version) is an inverse frequency shift capacitance level and material detection switch with optional rod/cable choices and configurable output. CLS300 is ideal for detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure and temperatures are present and has the ability to tune out buildup on the probe. Benefits Active-Shield technology so measurement is unaffected by material buildup or nozzle interference in active shield section Performs in extremely abrasive conditions because of solid rod construction Three LED indicators for adjustment control, output status, and power High-temperature version up to 00 C (752 ) Keep unit out of path of falling material, or protect probe from falling material. Build up of material in active shield area does not affect switch operation. Application Pointek CLS300 standard version has three LED indicators with basic relay and solid-state switch alarms. The robust design of CLS300 makes it specifically applicable for heavy solids applications where abrasive materials occur as in the mining industry. The fully potted electronics are unaffected by condensation, dust or vibration. Wetted parts are made of stainless steel with a PA shield for high chemical resistance, and of ceramic and stainless steel for high temperature version. Materials with low or high dielectric constants can be accurately detected. The unique Active Shield suppresses interference from material buildup or long installation nozzles. The unique modular design of the Pointek CLS300 provides a wide range of configurations, process connections, extensions and approvals to meet the temperature and pressure requirements of specific applications. The modular design makes ordering easier and reduces stocking requirements. A wide range of probe configurations are available, including rod and cable versions. Key Applications: liquids, slurries, bulk solids, relatively high pressure and temperature, hazardous areas, milling and mining applications Install probe at least 50 (2) from tank wall. Note angle of repose and adjust accordingly. Pointek CLS300 installation, dimensions in mm (inch) Min. 50 (2) Min. 50 (2) /2 Siemens I 0 Update /207
Pointek CLS300 - Standard Technical specifications Mode of operation Measuring principle Inverse frequency shift capacitive level detection Input Measured variable Change in picoarad (p) Output Output signal Relay output SPDT orm C relay - Max. contact voltage 30 V DC 250 V AC - Max. contact current 5 A (DC) 8 A (AC) - Max. switching capacity 50 W (DC) 2 000 VA (AC) - Time delay (ON and/or O)... 60 s Solid-state output -Output alvanically isolated -Protection Against reversed polarity (bipolar) - Max. switching voltage 30 V (DC) 30 V peak (AC) - Max. load current 82 ma - Voltage drop < V, typical at 50 ma - Time delay (pre or post switching)... 60 s Accuracy Resolution Min. sensitivity (p) % change in actual capacitance Max. temperature error 0.2 % of actual capacitance value Rated operating conditions ) Installation conditions Location Indoor/outdoor Ambient conditions Ambient temperature -0... +85 C (-0... +85 ) 2) Medium conditions Liquids, bulk solids, slurries and interfaces, and applications with viscous materials Relative dielectric constant r Min..5 Process temperature - Rod/Cable version -0... +200 C (-0... +392 ) 2) - High-temperature version -0... +00 C (-0... +752 ) Process pressure 3) -... +35 bar g (-.6... +5 psi g) Design Material (enclosure) Degree of Protection Cable inlet Controls and displays Displays Potentiometers Switches Power supply Supply Certificates and approvals eneral Purpose lameproof Enclosure with IS Probe Powder-coated aluminum with gasket Standard: Type /NEMA /IP65 Optional: Type /NEMA /IP68 2 x M20 x.5 thread (option: 2 x ½" NPT conduit entry including plugged entry) 3 LEDs, for probe status, output status and power supply 2 potentiometers for time delay and sensitivity 5 DIP switches for delay on/off, failsafe high/low, time delay test/adjust, high/low sensitivity, test delay settings 2... 250 V AC/DC, 0... 60 Hz, galvanically isolated, 2 W CSA, M, CE, RCM ATEX II /2 EEx d[ia] IIC T6... T ATEX II /2 D T00 C Dust Ignition Proof with IS Probe ATEX II /2 D T00 C CSA/M Class II, Div., roups E,, CSA/M Class III T Explosion Proof Enclosure with IS Probe Marine Overfill Protection Others CSA/M Class I, Div., roups A, B, C, D CSA/M Class II, Div., roups E,, CSA/M Class III T Lloyds Register of Shipping, Categories ENV, ENV2, and ENV5 WH (ermany) VLAREM II (Belgium) Pattern Approval (China) ) When operation is in areas classified as hazardous, observe restrictions according to relevant certificate. See also Pressure/Temperature curves starting on page /56. 2) Thermal isolator is used if process connection temperature exceeds 85 C (85 ). 3) Pressure rating of process seal is temperature dependent. See Pressure/Temperature curves starting on page /56. Design: Probe Length Sensor wetted parts Rod version High Temperature version Cable version Min. 250 mm (9.8 inch), max. 000 mm (0 inch) PA (no insulation on active probe), 36L stainless steel, PEEK isolators Min. 250 mm (9.8 inch), max. 000 mm (0 inch) Ceramic (ZrO ) 2 ) isolators (no insulation on active probe), 36L stainless steel Min. 000 mm (0 inch), max. 25 000 mm (98 inch) 36 stainless steel, optional PA, PEEK isolators O-ring seal material KM (optional KM) 2) raphite 2) KM (optional KM) 2) Thermal isolator Optional Standard Optional Extension User selectable length User selectable length User selectable cable length ) Zirconium Oxide 2) or caustic materials, consult a local sales person for alternative O-rings. or more information, please visit http://www.automation.siemens.com/aspa_app. Siemens I 0 Update /207 /3
Pointek CLS300 - Standard Pointek CLS300 - Standard - Rod Version with Threaded or langed process connection 7ML5650-7 7 7 7 7-7 7 7 7 choices and configurable output. CLS300 is ideal for detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure and temperatures are present, and has the ability to tune out buildup on the probe. Click on the for the online configuration in the PIA Life Cycle Portal. Process connection Threaded, 36L stainless steel ¾" NPT [(Taper), ANSI/ASME B.20.] 0 A " NPT [(Taper), ANSI/ASME B.20.] 0 B ¼" NPT [(Taper), ANSI/ASME B.20.] 0 C ½" NPT [(Taper), ANSI/ASME B.20.] 0 D R ¾" [(BSPT), EN 0226/PT (JIS-T), JIS B 0203] A R " [(BSPT), EN 0226/PT (JIS-T), JIS B 0203] B R ½" [(BSPT), EN 0226/PT (JIS-T), D JIS B 0203] ¾" [(BSPP), EN ISO 228-/P (JIS-P), 3 A " [(BSPP), EN ISO 228-/P (JIS-P), 3 B ½" [(BSPP), EN ISO 228-/P (JIS-P), 3 D Welded flange, 36L stainless steel, raised face " ASME, 50 lb 5 A " ASME, 300 lb 5 B " ASME, 600 lb 5 C ½" ASME, 50 lb 5 D ½" ASME, 300 lb 5 E ½" ASME, 600 lb 5 2" ASME, 50 lb 5 2" ASME, 300 lb 5 H 2" ASME, 600 lb 5 J 3" ASME, 50 lb 5 K 3" ASME, 300 lb 5 L 3" ASME, 600 lb 5 M " ASME, 50 lb 5 N " ASME, 300 lb 5 P " ASME, 600 lb 5 Q Welded flange, 36L stainless steel, Type A flat faced DN 25, PN 6 6 A DN 25, PN 0 6 B DN 0, PN 6 6 C DN 0, PN 0 6 D DN 50, PN 6 6 E DN 50, PN 0 6 DN 80, PN 6 6 DN 80, PN 0 6 H DN 00, PN 6 6 J DN 00, PN 0 6 K (Note: flange bolting patterns and facings dimensionally correspond to the applicable ASME B6.5 or EN 092- standard.) Probe length (length from flange face) (threaded lengths include process thread) Note: No Y0 needed in Order code for standard lengths Standard version, rod 350 mm (3.78 inch) A Extended rod, length 500 mm (9.69 inch) B Extended rod, length 750 mm (29.53 inch) C Extended rod, length 000 mm (39.37 inch) D Pointek CLS300 - Standard - Rod Version 7ML5650- with Threaded or langed process connection 7 7 7 7 7-7 7 7 7 choices and configurable output. CLS300 is ideal for detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure and temperatures are present, and has the ability to tune out buildup on the probe. Add Order code Y0 and plain text: "Insertion length... mm" E 250... 99 mm (9.8... 9.65 inch) 500... 79 mm (9.69... 29.9 inch) 750... 999 mm (29.53... 39.3 inch) Thermal isolator Without thermal isolator 0 With thermal isolator [for process connection temperatures over 85 C (85 )] Wetted seals KM 0 KM [for process temperatures above -20 C (- )] Probe material 36L stainless steel with PA lining and PEEK 0 isolators Approvals Dust Ignition Proof with IS Probe: C CE, RCM, ATEX II /2 D T00 C lameproof Enclosure with IS Probe: D CE, RCM, ATEX II /2 EEx d[ia] IIC T6... T, ATEX II /2 D T00 C lameproof Enclosure with IS Probe, E with WH approval: CE, RCM, ATEX II /2 EEx d[ia] IIC T6... T, ATEX II /2 D T00 C Dust Ignition Proof with IS Probe: CSA/M Class II, Div., roups E,, CSA/M Class III T Explosion Proof Enclosure with IS Probe: CSA/M Class I, Div., roups A, B, C, D CSA/M Class II, Div., roups E,, CSA/M Class III T eneral Purpose (CSA, M) H eneral Purpose (CE, RCM) J eneral Purpose with WH approval K (CSA, M, CE, RCM) Enclosure and lid Aluminum epoxy coated 2 x ½" NPT via adapter - cable inlet, IP65 A 2 x M20 x.5 cable inlet, IP65 B 2 x ½" NPT via adapter - cable inlet, IP68 C 2 x M20 x.5 cable inlet, IP68 D Active shield length Standard length - 0 (25 mm threaded, 05 mm flanged) (250 mm threaded, 230 mm flanged) ) 2 (00 mm threaded, 380 mm flanged) 2) ) Available with Probe version options B... D,, only [ 500 mm (9.69 inch)] 2) Available with Probe version options C, D, and only [ 750 mm (29.53 inch)] / Siemens I 0 Update /207
Pointek CLS300 - Standard Order code urther designs Please add "-Z" to and specify Order code(s). Total insertion length: enter the total insertion length Y0 in plain text description Stainless steel tag [70 x 3 mm (2.75 x 0.5 inch)]: Y5 Measuring-point number/identification (max. 27 characters) specify in plain text Manufacturer's test certificate: M to DIN 55350, C Part 8 and to ISO 9000 Material Inspection Certificate Type 3. per C2 EN 020 Operating Instructions All literature is available to download for free, in a range of languages, at http://www.siemens.com/ processinstrumentation/documentation Accessories See page /55 Pointek CLS300 - Standard - Cable Version 7ML565- with Threaded or langed process connection 7 7 7 77-77 7 7 choices and configurable output. CLS300 is ideal for detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure and temperatures are present, and has the ability to tune out buildup on the probe. Click on the for the online configuration in the PIA Life Cycle Portal. Process connection Threaded, 36L stainless steel ¼" NPT [(Taper), ANSI/ASME B.20.] 0 C ½" NPT [(Taper), ANSI/ASME B.20.] 0 D R ½" [(BSPT), EN 0226/PT (JIS-T), D JIS B 0203] ½" [(BSPP), EN ISO 228-/P (JIS-P), 3 D Welded flange, 36L stainless steel, raised face ½" ASME, 50 lb 5 D ½" ASME, 300 lb 5 E ½" ASME, 600 lb 5 2" ASME, 50 lb 5 2" ASME, 300 lb 5 H 2" ASME, 600 lb 5 J 3" ASME, 50 lb 5 K 3" ASME, 300 lb 5 L 3" ASME, 600 lb 5 M " ASME, 50 lb 5 N " ASME, 300 lb 5 P " ASME, 600 lb 5 Q Welded flange, 36L stainless steel, Type A flat faced DN 0, PN 6 6 C DN 0, PN 0 6 D DN 50, PN 6 6 E DN 50, PN 0 6 DN 80, PN 6 6 DN 80, PN 0 6 H DN 00, PN 6 6 J DN 00, PN 0 6 K (Note: lange bolting patterns and facings dimensionally correspond to the applicable ASME B6.5 or EN 092- standard.) Probe length (length from flange face) (threaded lengths include process thread) Note: No Y0 needed in Order code for standard lengths Extended cable, 3 000 mm (8. inch), A length can be shortened by customer Extended cable, 6 000 mm (236.22 inch), B length can be shortened by customer Add Order code Y0 and plain text: "Insertion length... mm" Extended cable, 500... 000 mm E (9.69... 39.37 inch) Extended cable, 00... 5 000 mm (39.... 96.85 inch) Extended cable, 5 00... 0 000 mm (96.89... 393.70 inch) Extended cable, 0 00... 5 000 mm H (393.7... 590.55 inch) Extended cable, 5 00... 20 000 mm J (590.59... 787.0 inch) Extended cable, 20 00... 25 000 mm K (787.... 98.25 inch) Siemens I 0 Update /207 /5
Pointek CLS300 - Standard Pointek CLS300 - Standard - Cable Version with Threaded or langed process connection choices and configurable output. CLS300 is ideal for detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure and temperatures are present, and has the ability to tune out buildup on the probe. 7ML565-7 7 7 77-77 7 7 Thermal isolator Without thermal isolator 0 With thermal isolator [for process connection temperatures over 85 C (85 )] Wetted seals KM 0 KM [for process temperatures above -20 C (- )] Probe material Bare 36L stainless steel cable, PEEK isolators and 0 36L stainless steel cable weight PA coated cable, PEEK isolators and 36L stainless steel cable weight Approvals Dust Ignition Proof with IS Probe: C CE, RCM, ATEX II /2 D T00 C lameproof Enclosure with IS Probe: D CE, RCM, ATEX II /2 EEx d[ia] IIC T6... T, ATEX II /2 D T00 C lameproof Enclosure with IS Probe, E with WH approval: CE, RCM, ATEX II /2 EEx d[ia] IIC T6... T, ATEX II /2 D T00 C Dust Ignition Proof with IS Probe: CSA/M Class II, Div., roups E,, CSA/M Class III T Explosion Proof Enclosure with IS Probe: CSA/M Class I, Div., roups A, B, C, D CSA/M Class II, Div., roups E,, CSA/M Class III T eneral Purpose (CSA, M) H eneral Purpose (CE, RCM) J eneral Purpose with WH approval K (CSA, M, CE, RCM) Enclosure and lid Aluminum epoxy coated 2 x ½" NPT via adapter - cable inlet, IP65 A 2 x M20 x.5 cable inlet, IP65 B 2 x ½" NPT via adapter - cable inlet, IP68 C 2 x M20 x.5 cable inlet, IP68 D Active shield length Standard length - 0 (25 mm threaded, 05 mm flanged) (250 mm threaded, 230 mm flanged) 2 (00 mm threaded, 380 mm flanged) ) ) Available with Probe version options A, B,... K, only [ 000 mm (39.7 inch)]. Order code urther designs Please add "-Z" to and specify Order code(s). Total insertion length: enter the total insertion length Y0 in plain text description Stainless steel tag [70 x 3 mm (2.75 x 0.5 inch)]: Y5 Measuring-point number/identification (max. 27 characters) specify in plain text Manufacturer's test certificate: M to DIN 55350, C Part 8 and to ISO 9000 Material Inspection Certificate Type 3. per C2 EN 020 Operating Instructions All literature is available to download for free, in a range of languages, at http://www.siemens.com/ processinstrumentation/documentation Accessories See page /55 /6 Siemens I 0 Update /207
Pointek CLS300 - Standard Pointek CLS300 - Standard - High Temperature Rod Version with Threaded or langed process connection 7ML5652-7 7 7 00 7-77 7 7 choices and configurable output. CLS300 is ideal for detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure and temperatures are present, and has the ability to tune out buildup on the probe. Click on the for the online configuration in the PIA Life Cycle Portal. Process connection Threaded, 36L stainless steel ¾" NPT [(Taper), ANSI/ASME B.20.] 0 A " NPT [(Taper), ANSI/ASME B.20.] 0 B ¼" NPT [(Taper), ANSI/ASME B.20.] 0 C ½" NPT [(Taper), ANSI/ASME B.20.] 0 D R ¾" [(BSPT), EN 0226/PT (JIS-T), JIS B 0203] A R " [(BSPT), EN 0226/PT (JIS-T), JIS B 0203] B R ½" [(BSPT), EN 0226/PT (JIS-T), D JIS B 0203] ¾" [(BSPP), EN ISO 228-/P (JIS-P), 3 A " [(BSPP), EN ISO 228-/P (JIS-P), 3 B ½" [(BSPP), EN ISO 228-/P (JIS-P), 3 D Welded flange, 36L stainless steel, raised face " ASME, 50 lb 5 A " ASME, 300 lb 5 B " ASME, 600 lb 5 C ½" ASME, 50 lb 5 D ½" ASME, 300 lb 5 E ½" ASME, 600 lb 5 2" ASME, 50 lb 5 2" ASME, 300 lb 5 H 2" ASME, 600 lb 5 J 3" ASME, 50 lb 5 K 3" ASME, 300 lb 5 L 3" ASME, 600 lb 5 M " ASME, 50 lb 5 N " ASME, 300 lb 5 P " ASME, 600 lb 5 Q Welded flange, 36L stainless steel, Type A flat faced DN 25, PN 6 6 A DN 25, PN 0 6 B DN 0, PN 6 6 C DN 0, PN 0 6 D DN 50, PN 6 6 E DN 50, PN 0 6 DN 80, PN 6 6 DN 80, PN 0 6 H DN 00, PN 6 6 J DN 00, PN 0 6 K (Note: lange bolting patterns and facings dimensionally correspond to the applicable ASME B6.5 or EN 092- standard.) Probe length (length from flange face) (threaded lengths include process thread) Note: No Y0 needed in Order code for standard lengths Standard version rod, 350 mm (3.78 inch) A Extended rod, length 500 mm (9.69 inch) B Extended rod, length 750 mm (29.53 inch) C Extended rod, length 000 mm (39.37 inch) D Pointek CLS300 - Standard - High Temperature 7ML5652- Rod Version with Threaded or langed process 7 7 7 0 7-77 7 7 connection choices and configurable output. CLS300 is ideal for detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure and temperatures are present, and has the ability to tune out buildup on the probe. Add Order code Y0 and plain text: "Insertion length... mm" E 250... 99 mm (9.8... 9.65 inch) 500... 79 mm (9.69... 29.9 inch) 750... 999 mm (29.53... 39.3 inch) Wetted seals raphite 0 Probe material 36L stainless steel with ceramic (ZrO 2 ) isolators 0 Approvals Dust Ignition Proof with IS Probe: C CE, RCM, ATEX II /2 D T00 C lameproof Enclosure with IS Probe: D CE, RCM, ATEX II /2 EEx d[ia] IIC T6... T, ATEXII /2 D T00 C lameproof Enclosure with IS Probe, E with WH approval: CE, RCM, ATEX II /2 EEx d[ia] IIC T6... T, ATEX II /2 D T00 C Dust Ignition Proof with IS Probe: CSA/M Class II, Div., roups E,, CSA/M Class III T Explosion Proof Enclosure with IS Probe: CSA/M Class I, Div., roups A, B, C, D CSA/M Class II, Div., roups E,, CSA/M Class III T eneral Purpose (CSA, M) H eneral Purpose (CE, RCM) J eneral Purpose with WH approval K (CSA, M, CE, RCM) Enclosure and lid Aluminum epoxy coated 2 x ½" NPT via adapter - cable inlet, IP65 A 2 x M20 x.5 cable inlet, IP65 B 2 x ½" NPT via adapter - cable inlet, IP68 C 2 x M20 x.5 cable inlet, IP68 D Active shield length Standard length - 0 (25 mm threaded, 05 mm flanged) (250 mm threaded, 230 mm flanged) ) 2 (00 mm threaded, 380 mm flanged) 2) ) Available with Probe version options B... D,, only [ 500 mm (9.69 inch)] 2) Available with Probe version options C, D, and only [ 750 mm (29.53 inch)] Siemens I 0 Update /207 /7
Pointek CLS300 - Standard Order code urther designs Please add "-Z" to and specify Order code(s). Total insertion length: enter the total insertion length Y0 in plain text description ) Stainless steel tag [70 x 3 mm (2.75 x 0.5 inch)]: Y5 Measuring-point number/identification (max. 27 characters) specify in plain text Manufacturer's test certificate: M to DIN 55350, C Part 8 and to ISO 9000 Material Inspection Certificate Type 3. per C2 EN 020 Operating Instructions All literature is available to download for free, in a range of languages, at http://www.siemens.com/ processinstrumentation/documentation Accessories See page /55 ) Not available with Probe length option B. /8 Siemens I 0 Update /207
Pointek CLS300 - Digital Overview Configuration Installation Pointek CLS300 (digital version) is an inverse frequency shift capacitance level and material detection switch with optional rod/cable choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure and temperatures are present and has the ability to tune out buildup on the probe. The digital version includes PROIBUS PA, an LCD display, and advanced diagnostic features. Benefits Active-Shield technology so measurement is unaffected by material buildup or nozzle interference in active shield section Performs in extremely abrasive conditions because of solid rod construction Push-button calibration, full-function diagnostics High sensitivity allows installation in a wide range of liquids, solids or slurry applications Integral LCD display allows for easy menu-driven setup PROIBUS PA communication (SIMATIC PDM compatible) Keep unit out of path of falling material, or protect probe from falling material. Build up of material in active shield area does not affect switch operation. Application Pointek CLS300 digital version provides an integral LCD display for stand-alone use, with PROIBUS PA communication (Profile version 3.0, Class B) when required. Solid-state switch alarm is standard. The robust design of CLS300 makes it specifically applicable for heavy solids applications where abrasive materials occur as in the mining industry. The fully potted electronics are unaffected by condensation, dust or vibration. Wetted parts are made of stainless steel with a PA shield for high chemical resistance, and of ceramic and stainless steel for high temperature version. Materials with low or high dielectric constants can be accurately detected. The unique Active Shield suppresses interference from material buildup or long installation nozzles. The unique modular design of the Pointek CLS300 provides a wide range of configurations, process connections, extensions and approvals to meet the temperature and pressure requirements of specific applications. The modular design makes ordering easier and reduces stocking requirements. A wide range of probe configurations are available, including rod and cable versions. Key Applications: liquids, slurries, bulk solids, relatively high pressure and temperature, hazardous areas, milling and mining applications Install probe at least 50 (2) from tank wall. Note angle of repose and adjust accordingly. Pointek CLS300 installation, dimensions in mm (inch) Min. 50 (2) Min. 50 (2) Siemens I 0 Update /207 /9
Pointek CLS300 - Digital Technical specifications Mode of operation Measuring principle Inverse frequency shift capacitive level detection Input Measured variable Change in picoarad (p) Output Solid-state output Output alvanically isolated Protection Against reversed polarity (bipolar) Max. switching voltage 30 V (DC) 30 V peak (AC) Max. load current 82 ma Voltage drop < V, typical at 50 ma Time delay (pre or post switching) Programmable by user (0... 00 s) ail-safe mode Min. or max. Connection Removable terminal block Accuracy Resolution Min. sensitivity (p) % change in actual capacitance Max. temperature error 0.2 % of actual capacitance value Rated operating conditions ) Installation conditions Location Indoor/outdoor Ambient conditions Ambient temperature -0... +85 C (-0... +85 ) 2) Medium conditions Liquids, bulk solids, slurries, interfaces, and applications with viscous materials Relative dielectric constant r Min..5 Process temperature - Rod/Cable version -0... +200 C (-0... +392 ) 2) - High Temperature version -0... +00 C (-0... +752 ) Process pressure 3) -... +35 bar g (-.6... +5 psi g) Design Material (enclosure) Powder-coated aluminum with gasket Degree of protection Standard: Type /NEMA /IP65 Optional: Type /NEMA /IP68 Cable inlet 2 x M20 x.5 thread (option: 2 x ½" NPT conduit entry including plugged entry) Controls and displays Local display LCD Configuration Locally, using 3 button keypad (for standalone operation) Remotely, using SIMATIC PDM (for installation on a network) Power supply Bus voltage (at process connection) Standard: 2... 30 V DC Intrinsically Safe: 2... 2 V DC 2.5 ma Current consumption Certificates and approvals eneral Purpose CSA, M, CE, RCM Dust Ignition Proof ATEX II /2 D, 2 D IP6X T00 C lameproof Enclosure With IS Probe ATEX II /2 EEx d[ia] IIC T6... T ATEX II /2 D T00 C Dust Ignition Proof With IS Probe CSA/M Class II, Div., roups E,, CSA/M Class III T Intrinsically Safe ) ATEX II EEx ia IIC T6... T ATEX II /2 D, 2 D IP6X T00 C CSA/M Class I, Div., roups A, B, C, D CSA/M Class II, Div., roups E,, CSA/M Class III T Non-incendive CSA/M Class I, Div. 2, roups A, B, C, D CSA/M Class II, Div. 2, roups, CSA/M Class III T or T6 Explosion Proof with IS Probe CSA/M Class I, Div., roups A, B, C, D CSA/M Class II, Div., roups E,, CSA/M Class III T Marine Lloyds Register of Shipping, Categories ENV, ENV2, and ENV5 Others Pattern Approval (China) Communication PROIBUS PA (IEC 658 CP3 CP3/2) Bus physical layer: IEC 658-2 MBP-(IS) Device profile: PROIBUS PA profile for Process Control Devices Version 3.0, Class B ISCO field device ) When operation is in areas classified as hazardous, observe restrictions according to relevant certificate. See also Pressure/Temperature curves starting on page /56. 2) Thermal isolator is used if process connection temperature exceeds 85 C (85 ) 3) Pressure rating of process seal is temperature dependent. See Pressure/Temperature curves starting on page /56. ) Barrier or Intrinsically Safe power supply required for Intrinsically Safe protection Design: Probe Length Sensor wetted parts Rod version High Temperature version Cable version Min. 250 mm (9.8 inch), max. 000 mm (0 inch) PA (no insulation on active probe), 36L stainless steel, PEEK isolators Min. 250 mm (9.8 inch), max. 000 mm (0 inch) Ceramic (ZrO ) 2 ) isolators (no insulation on active probe), 36L stainless steel Min. 000 mm (0 inch), max. 25 000 mm (98 inch) 36 stainless steel, optional PA, PEEK isolators O-ring seal material KM (optional KM) 2) raphite 2) KM (optional KM) 2) Thermal isolator Optional Standard Optional Extension User selectable length User selectable length User selectable cable length ) Zirconium Oxide 2) or caustic materials, consult a local sales person for alternative O-rings. or more information, please visit http://www.automation.siemens.com/aspa_app. /50 Siemens I 0 Update /207
Pointek CLS300 - Digital Pointek CLS300 - Digital - Rod with Threaded or langed process connection 7ML5660-7 7 7 77-77 7 7 choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure and temperatures are present and has the ability to tune out buildup on the probe. Click on the for the online configuration in the PIA Life Cycle Portal. Process connection Threaded, 36L stainless steel ¾" NPT [(Taper), ANSI/ASME B.20.] 0 A " NPT [(Taper), ANSI/ASME B.20.] 0 B ¼" NPT [(Taper), ANSI/ASME B.20.] 0 C ½" NPT [(Taper), ANSI/ASME B.20.] 0 D R ¾" [(BSPT), EN 0226/PT (JIS-T), JIS B 0203] A R " [(BSPT), EN 0226/PT (JIS-T), JIS B 0203] B R ½" [(BSPT), EN 0226/PT (JIS-T), D JIS B 0203] ¾" [(BSPP), EN ISO 228-/P (JIS-P), 3 A " [(BSPP), EN ISO 228-/P (JIS-P), 3 B ½" [(BSPP), EN ISO 228-/P (JIS-P), 3 D Welded flange, 36L stainless steel, raised face " ASME, 50 lb 5 A " ASME, 300 lb 5 B " ASME, 600 lb 5 C ½" ASME, 50 lb 5 D ½" ASME, 300 lb 5 E ½" ASME, 600 lb 5 2" ASME, 50 lb 5 2" ASME, 300 lb 5 H 2" ASME, 600 lb 5 J 3" ASME, 50 lb 5 K 3" ASME, 300 lb 5 L 3" ASME, 600 lb 5 M " ASME, 50 lb 5 N " ASME, 300 lb 5 P " ASME, 600 lb 5 Q Welded flange, 36L stainless steel, Type A flat faced DN 25, PN 6 6 A DN 25, PN 0 6 B DN 0, PN 6 6 C DN 0, PN 0 6 D DN 50, PN 6 6 E DN 50, PN 0 6 DN 80, PN 6 6 DN 80, PN 0 6 H DN 00, PN 6 6 J DN 00, PN 0 6 K (Note: lange bolting patterns and facings dimensionally correspond to the applicable ASME B6.5 or EN 092- standard.) Probe length (length from flange face) (threaded lengths include process thread) Note: No Y0 needed in Order code for standard lengths Standard version, rod 350 mm (3.78 inch) A Extended rod, length 500 mm (9.69 inch) B Extended rod, length 750 mm (29.53 inch) C Extended rod, length 000 mm (39.37 inch) D Pointek CLS300 - Digital - Rod with 7ML5660- Threaded or langed process connection 7 7 7 77-77 7 7 choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure and temperatures are present and has the ability to tune out buildup on the probe. Add Order code Y0 and plain text: "Insertion length... mm" E 250... 99 mm (9.8... 9.65 inch) 500... 79 mm (9.69... 29.9 inch) 750... 999 mm (29.53... 39.3 inch) Thermal isolator Without thermal isolator 0 With thermal isolator [for process connection temperatures over 85 C (85 )] Wetted seals KM 0 KM [for process temperatures above -20 C (- )] Probe material 36L stainless steel with PA lining and PEEK 0 isolators Approvals Dust Ignition Proof: B CE, RCM, ATEX II /2 D, 2 D IP6X T00 C Intrinsically Safe ) C CE, RCM, ATEX II EEx ia IIC T6... T, ATEX II /2 D, 2 D IP6X T00 C lameproof Enclosure with IS Probe: D CE, RCM, ATEX II /2 EEx d[ia] IIC T6... T, ATEX II /2 D T00 C Dust Ignition Proof with IS Probe: E CSA/M Class II, Div., roups E,, CSA/M Class III T Intrinsically Safe ) CSA/M Class I, Div., roups A, B, C, D CSA/M Class II, Div., roups E,, CSA/M Class III T Explosion Proof Enclosure with IS Probe: CSA/M Class I, Div., roups A, B, C, D CSA/M Class II, Div., roups E,, CSA/M Class III T eneral Purpose (CSA, M) H eneral Purpose (CSA, M, CE, RCM) J Siemens I 0 Update /207 /5
Pointek CLS300 - Digital Pointek CLS300 - Digital - Rod with 7ML5660- Threaded or langed process connection 7 7 7 77-77 7 7 choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure and temperatures are present and has the ability to tune out buildup on the probe. Enclosure and Lid Aluminum epoxy coated 2 x ½" NPT via adapter - cable inlet, IP65 A 2 x M20 x.5 cable inlet, IP65 B 2 x ½" NPT via adapter - cable inlet, IP68 C 2 x M20 x.5 cable inlet, IP68 D Active shield length Standard length - 0 (25 mm threaded, 05 mm flanged) (250 mm threaded, 230 mm flanged) 2) 2 (00 mm threaded, 380 mm flanged) 3) )Barrier or Intrinsically Safe power supply required for Intrinsically Safe protection 2) Available with Probe version options B... D,, only [ 500 mm (9.69 inch)] 3) Available with Probe version options C, D, and only [ 750 mm (29.53 inch)] Order code urther designs Please add "-Z" to and specify Order code(s). Total insertion length: enter the total insertion length Y0 in plain text description Stainless steel tag [70 x 3 mm (2.75 x 0.5 inch)]: Y5 Measuring-point number/identification (max. 27 characters) specify in plain text Manufacturer's test certificate: M to DIN 55350, C Part 8 and to ISO 9000 Material inspection Certificate Type 3. per C2 EN 020 Operating Instructions All literature is available to download for free, in a range of languages, at http://www.siemens.com/ processinstrumentation/documentation Accessories See page /55 Pointek CLS300 - Digital - Cable with 7ML566- Threaded or langed process connection 7 7 7 77-77 7 7 choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure and temperatures are present and has the ability to tune out buildup on the probe. Click on the for the online configuration in the PIA Life Cycle Portal. Process connection Threaded, 36L stainless steel ¼" NPT [(Taper), ANSI/ASME B.20.] 0 C ½" NPT [(Taper), ANSI/ASME B.20.] 0 D R ½" [(BSPT), EN 0226/PT (JIS-T), JIS B 0203] D ½" [(BSPP), EN ISO 228-/P (JIS-P), 3 D Welded flange, 36L stainless steel, raised face ½" ASME, 50 lb 5 D ½" ASME, 300 lb 5 E ½" ASME, 600 lb 5 2" ASME, 50 lb 5 2" ASME, 300 lb 5 H 2" ASME, 600 lb 5 J 3" ASME, 50 lb 5 K 3" ASME, 300 lb 5 L 3" ASME, 600 lb 5 M " ASME, 50 lb 5 N " ASME, 300 lb 5 P " ASME, 600 lb 5 Q Welded flange, 36L stainless steel, Type A flat faced DN 0, PN 6 6 C DN 0, PN 0 6 D DN 50, PN 6 6 E DN 50, PN 0 6 DN 80, PN 6 6 DN 80, PN 0 6 H DN 00, PN 6 6 J DN 00, PN 0 6 K (Note: lange bolting patterns and facings dimensionally correspond to the applicable ASME B6.5 or EN 092- standard.) Probe length (length from flange face) (threaded lengths include process thread) Note: No Y0 needed in Order code for standard lengths Extended cable, 3 000 mm (8. inch), A length can be shortened by customer Extended cable, 6 000 mm (236.22 inch), B length can be shortened by customer Add Order code Y0 and plain text: "Insertion length... mm" Extended cable, 500... 000 mm E (9.69... 39.37 inch) Extended cable, 00... 5 000 mm (39.... 96.85 inch) Extended cable, 5 00... 0 000 mm (96.89... 393.70 inch) Extended cable, 0 00... 5 000 mm H (393.7... 590.55 inch) Extended cable, 5 00... 20 000 mm J (590.59... 787.0 inch) Extended cable, 20 00... 25 000 mm K (787.... 98.25 inch) /52 Siemens I 0 Update /207
Pointek CLS300 - Digital Pointek CLS300 - Digital - Cable with 7ML566- Threaded or langed process connection 7 7 7 77-77 7 7 choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure and temperatures are present and has the ability to tune out buildup on the probe. Thermal isolator Without thermal isolator 0 With thermal isolator [for process connection temperatures over 85 C (85 )] Wetted seals KM 0 KM [for process temperatures above -20 C (- )] Probe material Bare 36L stainless steel cable, PEEK isolators and 0 36L stainless steel cable weight PA coated cable, PEEK isolators and 36L stainless steel cable weight Approvals Dust Ignition Proof: B CE, RCM, ATEX II /2 D, 2 D IP6X T00 C Intrinsically Safe ) C CE, RCM, ATEX II EEx ia IIC T6... T, ATEX II /2 D, 2 D IP6X T00 C lameproof Enclosure with IS Probe: D CE, RCM, ATEX II /2 EEx d[ia] IIC T6... T, ATEX II /2 D T00 C Intrinsically Safe ) CSA/M Class I, Div., roups A, B, C, D CSA/M Class II, Div., roups E,, CSA/M Class III T Explosion Proof Enclosure with IS Probe: CSA/M Class I, Div., roups A, B, C, D CSA/M Class II, Div., roups E,, CSA/M Class III T eneral Purpose (CSA, M) H eneral Purpose (CSA, M, CE, RCM) J Enclosure and Lid Aluminum epoxy coated 2 x ½" NPT via adapter - cable inlet, IP65 A 2 x M20 x.5 cable inlet, IP65 B 2 x ½" NPT via adapter - cable inlet, IP68 C 2 x M20 x.5 cable inlet, IP68 D Active shield length Standard length - 0 (25 mm threaded, 05 mm flanged) (250 mm threaded, 230 mm flanged) 2 (00 mm threaded, 380 mm flanged) 2) ) Barrier or Intrinsically Safe power supply required for Intrinsically Safe protection. 2) Available with Probe version options A, B,... K, only [ 000 mm (39.7 inch)]. Order code urther designs Please add "-Z" to and specify Order code(s). Total insertion length: enter the total insertion length Y0 in plain text description Stainless steel tag [70 x 3 mm (2.75 x 0.5 inch)]: Y5 Measuring-point number/identification (max. 27 characters) specify in plain text Manufacturer's test certificate: M to DIN 55350, C Part 8 and to ISO 9000 Material inspection Certificate Type 3. per C2 EN 020 Operating Instructions All literature is available to download for free, in a range of languages, at http://www.siemens.com/ processinstrumentation/documentation Accessories See page /55 Siemens I 0 Update /207 /53
Pointek CLS300 - Digital Pointek CLS300 - Digital - High Temperature Rod version with Threaded or langed process connection choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure and temperatures are present and has the ability to tune out buildup on the probe. Click on the for the online configuration in the PIA Life Cycle Portal. Process connection Threaded, 36L stainless steel ¾" NPT [(Taper), ANSI/ASME B.20.] 0 A " NPT [(Taper), ANSI/ASME B.20.] 0 B ¼" NPT [(Taper), ANSI/ASME B.20.] 0 C ½" NPT [(Taper), ANSI/ASME B.20.] 0 D R ¾" [(BSPT), EN 0226/PT (JIS-T), JIS B 0203] A R " [(BSPT), EN 0226/PT (JIS-T), JIS B 0203] B R ½" [(BSPT), EN 0226/PT (JIS-T), JIS B 0203] ¾" [(BSPP), EN ISO 228-/P (JIS-P), " [(BSPP), EN ISO 228-/P (JIS-P), ½" [(BSPP), EN ISO 228-/P (JIS-P), Welded flange, 36L stainless steel, raised face " ASME, 50 lb 5 A " ASME, 300 lb 5 B " ASME, 600 lb 5 C ½" ASME, 50 lb 5 D ½" ASME, 300 lb 5 E ½" ASME, 600 lb 5 2" ASME, 50 lb 5 2" ASME, 300 lb 5 H 2" ASME, 600 lb 5 J 3" ASME, 50 lb 5 K 3" ASME, 300 lb 5 L 3" ASME, 600 lb 5 M " ASME, 50 lb 5 N " ASME, 300 lb 5 P " ASME, 600 lb 5 Q Welded flange, 36L stainless steel, Type A flat faced DN 25, PN 6 DN 25, PN 0 DN 0, PN 6 DN 0, PN 0 DN 50, PN 6 DN 50, PN 0 DN 80, PN 6 DN 80, PN 0 DN 00, PN 6 DN 00, PN 0 (Note: lange bolting patterns and facings dimensionally correspond to the applicable ASME B6.5 or EN 092- standard.) Probe length (length from flange face) (threaded lengths include process thread) Note: No Y0 needed in Order code for standard lengths Standard version rod, 350 mm (3.78 inch) Extended rod, length 500 mm (9.69 inch) Extended rod, length 750 mm (29.53 inch) Extended rod, length 000 mm (39.37 inch) 7ML5662-7 7 7 0 7-77 7 7 D 3 A 3 B 3 D 6 A 6 B 6 C 6 D 6 E 6 6 6 H 6 J 6 K A B C D Pointek CLS300 - Digital - High Temperature Rod version with Threaded or langed process connection choices and configurable output. It is ideal for detecting liquids, solids, slurries, foam, and interfaces in demanding conditions where high pressure and temperatures are present and has the ability to tune out buildup on the probe. Add Order code Y0 and plain text: "Insertion length... mm" 250... 99 mm (9.8... 9.65 inch) 500... 79 mm (9.69... 29.9 inch) 750... 999 mm (29.53... 39.3 inch) Wetted seals raphite 0 Probe material 36L stainless steel with ceramic (ZrO 2 ) isolators 0 Approvals Dust Ignition Proof: CE, RCM, ATEX II /2 D, 2 D IP6X T00 C Intrinsically Safe ) CE, RCM, ATEX II EEx ia IIC T6... T, ATEX II /2 D, 2 D IP6X T00 C lameproof Enclosure with IS Probe: CE, RCM, ATEX II /2 EEx d[ia] IIC T6... T, ATEX II /2 D T00 C Intrinsically Safe ) CSA/M Class I, Div., roups A, B, C, D CSA/M Class II, Div., roups E,, CSA/M Class III T Explosion Proof Enclosure with IS Probe: CSA/M Class I, Div., roups A, B, C, D CSA/M Class II, Div., roups E,, CSA/M Class III T eneral Purpose (CSA, M) eneral Purpose (CSA, M, CE, RCM) Enclosure and Lid Aluminum epoxy coated 7ML5662-7 7 7 0 7-77 7 7 2 x ½" NPT via adapter - cable inlet, IP65 A 2 x M20 x.5 cable inlet, IP65 B 2 x ½" NPT via adapter - cable inlet, IP68 C 2 x M20 x.5 cable inlet, IP68 D Active shield length Standard length - 0 (25 mm threaded, 05 mm flanged) (250 mm threaded, 230 mm flanged) 2) 2 (00 mm threaded, 380 mm flanged) 3) ) Barrier or Intrinsically Safe power supply required for Intrinsically Safe protection 2) Available with Probe version options B... D,, only [ 500 mm (9.69 inch)] 3) Available with Probe version options C, D, and only [ 750 mm (29.53 inch)] E B C D H J /5 Siemens I 0 Update /207
Pointek CLS 300 - Standard and Digital Order code urther designs Please add "-Z" to and specify Order code(s). Total insertion length: enter the total insertion length Y0 in plain text description Stainless steel tag [70 x 3 mm (2.75 x 0.5 inch)]: Y5 Measuring-point number/identification (max. 27 characters) specify in plain text Manufacturer's test certificate: M to DIN 55350, C Part 8 and to ISO 9000 Material Inspection Certificate Type 3. per C2 EN 020 Operating Instructions All literature is available to download for free, in a range of languages, at http://www.siemens.com/ processinstrumentation/documentation Accessories See page /55 Accessories One metallic cable gland M20 x.5, -0... +80 C (-0... +76 ) with integrated shield connection (available for PROIBUS PA) eneral Purpose /2" NPT eneral Purpose Cable Entry IP68/IP69K NEMA6, -0... +00 C (-0... +22 ), cable size 6... 2 mm (0.236... 0.72 inch) M20 x.5 eneral Purpose Cable Entry IP68/IP69K NEMA6, -0... +00 C (-0... +22 ), cable size 7... 2 mm (0.275... 0.72 inch) Hazardous Locations /2" NPT EMC rated Cable land: Dust Ignition Proof, lameproof Exd, and Increased Safety ATEX II 2 D ExtD A2 (Zone, Zone 2, Zone 2, Zone 22, and in as roups IIA,IIB and IIC) -60... +80 C IP66, IP67, IP68, NEMAX, cable sizes 5.5... 2 mm (0.26... 0.72 inch) M20 EMC rated Cable land: Dust Ignition Proof, lameproof Exd, and Increased Safety ATEX II 2 D ExtD A2 (Zone, Zone 2, Zone 2, Zone 22, and in as roups IIA,IIB and IIC) -60... +80 C IP66, IP67, IP68, NEMAX, cable sizes 5.5... 2 mm (0.26... 0.72 inch) Blind threaded flanges are available. Customers interested in a custom designed device should consult a local sales person. or more information, please visit http://www.automation.siemens.com/aspa_app. 7ML930-AQ 7ML830-JA 7ML830-JC 7ML830-JB 7ML830-JD Pointek Specials See page /62 Siemens I 0 Update /207 /55
Pointek CLS 300 - Standard and Digital Characteristic curves Pressure/temperature curve CLS300 extended rod and cable probes Threaded process connections (7ML5650, 7ML565, 7ML5660 and 7ML566) Permitted operating pressures P 0 bar (580 psi) 30 bar (35 psi) Atmospheric - bar (-.5 psi) -50 ºC (-238 º) -00 ºC (-8 º) 20 bar (290 psi) 0 bar (5 psi) -0 º º (-0 ºC) (-0 ºC) -50 ºC (-58 º) -29 ºC (-20 º) 00 º (38 ºC) 200 º (93 ºC) 0 ºC RT 50 ºC 00 ºC (32 º) (22 º) (22 º) 300 º (9 ºC) 50 ºC (302 º) 00 º (20 ºC) 200 ºC (392 º) 500 º (260 ºC) 250 ºC (82 º) 600 º (35 ºC) 300 ºC (572 º) 700 º (37 ºC) 350 ºC (662 º) 00 ºC (752 º) Permitted operating temperature T Example: Permitted operating pressure = 30 bar (35 psi) at 75 C Pointek CLS300 process pressure/temperature derating curves (7ML5650, 7ML565, 7ML5660 and 7ML566) Pressure/temperature curve CLS300 high temperature rod probes Threaded process connections (7ML5652 and 7ML5662) Permitted operating pressures P 0 bar (580 psi) 30 bar (35 psi) 20 bar (290 psi) Atmospheric - bar (-.5 psi) -50 ºC (-238 º) -00 ºC (-8 º) 0 bar (5 psi) -0 º º (-0 ºC) (-0 ºC) -50 ºC (-58 º) -29 ºC (-20 º) 00 º (38 ºC) 200 º (93 ºC) 0 ºC RT 50 ºC 00 ºC (32 º) (22 º) (22 º) 300 º (9 ºC) 50 ºC (302 º) 00 º (20 ºC) 200 ºC (392 º) 500 º (260 ºC) 250 ºC (82 º) 600 º (35 ºC) 300 ºC (572 º) 700 º (37 ºC) 350 ºC (662 º) 00 ºC (752 º) Permitted operating temperature T Pointek CLS300 process pressure/temperature derating curves (7ML5652 and 7ML5662) /56 Siemens I 0 Update /207
Pointek CLS 300 - Standard and Digital Pressure/temperature curve CLS300 extended rod and cable probes ASME flanged process connections (7ML5650, 7ML565, 7ML5660 and 7ML566) Permitted operating pressures P 50 bar (725 psi) 0 bar (580 psi) 30 bar (35 psi) ASME 300 lb ) 20 bar (290 psi) Atmospheric - bar (-.5 psi) -50 ºC (-238 º) -00 ºC (-8 º) 0 bar (5 psi) -0 º º (-0 ºC) (-0 ºC) -50 ºC (-58 º) -29 ºC (-20 º) 00 º (38 ºC) 200 º (93 ºC) 0 ºC RT 50 ºC 00 ºC (32 º) (22 º) (22 º) 300 º (9 ºC) 50 ºC (302 º) 00 º (20 ºC) 200 ºC (392 º) 500 º (260 ºC) 250 ºC (82 º) 600 º (35 ºC) 300 ºC (572 º) 700 º (37 ºC) 350 ºC (662 º) ASME 50 lb ) 00 ºC (752 º) Permitted operating temperature T ) The curve denotes the minimum allowable flange class for the shaded area below. Pointek CLS300 process pressure/temperature derating curves (7ML5650, 7ML565, 7ML5660, and 7ML566) Permitted operating pressures P 90 bar (.305 psi) Pressure/temperature curve CLS300 high temperature rod probes ASME flanged process connections (7ML5652 and 7ML5662) 80 bar (.60 psi) 70 bar (.05 psi) 60 bar (870 psi) ASME 600 lb ) 50 bar (725 psi) 0 bar (580 psi) 30 bar (35 psi) ASME 300 lb ) 20 bar (290 psi) Atmospheric - bar (-.5 psi) -50 ºC (-238 º) -00 ºC (-8 º) 0 bar (5 psi) -0 º º (-0 ºC) (-0 ºC) -50 ºC (-58 º) -29 ºC (-20 º) 00 º (38 ºC) 200 º (93 ºC) 0 ºC RT 50 ºC 00 ºC (32 º) (22 º) (22 º) 300 º (9 ºC) 50 ºC (302 º) 00 º (20 ºC) 200 ºC (392 º) 500 º (260 ºC) 250 ºC (82 º) 600 º (35 ºC) 300 ºC (572 º) 700 º (37 ºC) 350 ºC (662 º) ASME 50 lb ) 00 ºC (752 º) Permitted operating temperature T ) The curve denotes the minimum allowable flange class for the shaded area below. Pointek CLS300 process pressure/temperature derating curves (7ML5652 and 7ML5662) Siemens I 0 Update /207 /57
Pointek CLS 300 - Standard and Digital Pressure/temperature curve CLS300 extended rod and cable probes EN flanged process connections (7ML5650, 7ML565, 7ML5660 and 7ML566) Permitted operating pressures P 50 bar (725 psi) 0 bar (580 psi) Atmospheric - bar (-.5 psi) -50 ºC (-238 º) -00 ºC (-8 º) 30 bar (35 psi) 20 bar (290 psi) 0 bar (5 psi) -0 º º (-0 ºC) (-0 ºC) -50 ºC (-58 º) -29 ºC (-20 º) 00 º (38 ºC) 200 º (93 ºC) 0 ºC RT 50 ºC 00 ºC (32 º) (22 º) (22 º) 300 º (9 ºC) 50 ºC (302 º) 00 º (20 ºC) 200 ºC (392 º) 500 º (260 ºC) 250 ºC (82 º) 600 º (35 ºC) 300 ºC (572 º) 700 º (37 ºC) 350 ºC (662 º) 00 ºC (752 º) PN 0 ) PN 6 ) Permitted operating temperature T ) The curve denotes the minimum allowable flange class for the shaded area below. Pointek CLS300 process pressure/temperature derating curves (7ML5650, 7ML565, 7ML5660 and 7ML566) Pressure/Temperature Curve CLS300 High Temperature Rod Probes EN langed Process Connections (7ML5652 and 7ML5662) Permitted Operating Pressures P 50 bar (725 psi) 0 bar (580 psi) 30 bar (35 psi) 20 bar (290 psi) PN 0 ) Atmospheric - bar (-.5 psi) -50 ºC (-238 º) -00 ºC (-8 º) 0 bar (5 psi) -0 º º (-0 ºC) (-0 ºC) -50 ºC (-58 º) -29 ºC (-20 º) 00 º (38 ºC) 200 º (93 ºC) 0 ºC RT 50 ºC 00 ºC (32 º) (22 º) (22 º) 300 º (9 ºC) 50 ºC (302 º) 00 º (20 ºC) 200 ºC (392 º) 500 º (260 ºC) 250 ºC (82 º) 600 º (35 ºC) 300 ºC (572 º) 700 º (37 ºC) 350 ºC (662 º) PN 6 ) 00 ºC (752 º) Permitted Operating Temperature T ) The curve denotes the minimum allowable flange class for the shaded area below. Pointek CLS300 process pressure/temperature derating curves (7ML5652 and 7ML5662) /58 Siemens I 0 Update /207
Pointek CLS 300 - Standard and Digital Dimensional drawings Rod version Threaded (7ML5650 and 7ML5660) Lid clip Electronics/ enclosure Lid 20 (0.79) High temperature rod version Threaded (7ML5652 and 7ML5662) 2 cable entries ½" NPT or M20 x.5 Y02 ) Thermal isolator M20: 35 (5.32) ½" NPT: 50 (5.9) Probe Measuring length Y0 (insertion length) min. = 250 (9.8)/max. = 000 (39.37) Ceramic isolator(s) Probe Ø9 (0.75) Ø9 (0.75) Y02 ) Measuring length Y0 (insertion length) min. = 250 (9.8)/max. = 000 (39.37) 59 (6.26) 52 (5.98) Lid with window P, DIP lid, without window XP, lid without window 6 (5.75) 23 (9.2) Thermal isolator Cable version, non-insulated Threaded (7ML565 and 7ML566) Cable version, insulated Threaded (7ML565 and 7ML566) Y02 ) Y02 ) 20 (9.5) 27 (9.72) Stainless steel cable Ø6 (0.2) Stainless steel weight 250 (9.8) Measuring length Y0 (insertion length) min. = 500 (20)/max. = 25 000 (98) PA insulated cable Ø0 (0.35) Stainless steel weight 250 (9.8) Measuring length Y0 (insertion length) min. = 500 (20)/max. = 25 000 (98) Note: Ø32 (.26) Ø32 (.26) ) Extended Active Shield (Y02): standard length 25 (.92). Optional active shield lengths: 250 (9.8) or 00 (5.75). Pointek CLS300 threaded process connections, dimensions in mm (inch) Siemens I 0 Update /207 /59
Pointek CLS 300 - Standard and Digital Rod version Welded flange (7ML5650 and 7ML5660) Lid clip Lid High temperature rod version Welded flange (7ML5652 and 7ML5662) 2 cable entries ½" NPT or M20 x.5 Electronics/ enclosure M20: 35 (5.32) ½" NPT: 50 (5.9) Probe Y02 ) Measuring length Y0 (insertion length) min. = 250 (9.8)/max. = 000 (39.37) Thermal isolator Ceramic isolator(s) Probe Y02 ) Measuring length Y0 (insertion length) min. = 250 (9.8)/max. = 000 (39.37) 8 (7.3) 7 (6.85) Lid with window P, DIP lid, without window XP, lid without window 68 (6.6) 257 (0.2) Thermal isolator 263 (0.35) 270 (0.63) Ø 9 (0.75) Ø 9 (0.75) Cable version, non-insulated Welded flange (7ML565 and 7ML566) Cable version, insulated Welded flange (7ML565 and 7ML566) lange acing (raised face) lange Class acing thickness ASME 50/300 2 (0.08) ASME 600/900 7 (0.28) PN6/0 2 (0.08) Stainless steel cable Ø 6 (0.2) Stainless steel weight 250 (9.8) Y02 ) Measuring length Y0 (insertion length) min. = 500 (20)/max. = 25 000 (98) PA insulated cable Ø 0 (0.35) Stainless steel weight 250 (9.8) Y02 ) Measuring length Y0 (insertion length) min. = 500 (20)/max. = 25 000 (98) Ø 32 (.26) Ø 32 (.26) Note: ) Extended Active Shield (Y02): standard length 05 (.3). Optional active shield lengths: 230 (9.06) or 380 (.96). Insertion length does not include any raised face/gasket face dimension (see lange acing Table above) Pointek CLS300 flanged process connections, dimensions in mm (inch) /60 Siemens I 0 Update /207
Pointek CLS 300 - Standard and Digital Schematics Wiring: Pointek CLS300 standard White Black Red P - + Delay Switch bank S O L2 Output status (+) L Sensor status 3 2 Sensor (f) K Trip point ND L3 Power on 2 3 Power supply 2 to 250 V AC/DC NC NO NO K2 K3 Solid state switch: 30 V DC/30 V AC (peak), 82 ma max. Relay contact: 8 A at 250 V AC, 2 000 VA 5 A at 30 V DC, 50 W Notes: - Identification label is on underside of lid. Switch and potentiometer settings are for illustration purposes only (refer to operation/setup in manual). - All field wiring must have insulation suitable for at least 250 V. - Relay contact terminals are for use with equipment having no accessible live parts and wiring having insulation suitable for at least 250 V. - Maximum working voltage between adjacent relay contacts shall be 250 V. - Refer to the Instruction manual or contact Siemens representative for detailed wiring information. P2 K Wiring: Pointek CLS300 digital Test input White White Reed contact* Red (+) Alarm output solid-state switch Sensor 2 V DC/PROIBUS PA Black (-) Orange (f) Power connection: 2 V DC or PROIBUS PA bus (not polarity sensitive). Notes: Refer to the instruction manual or contact a Siemens representative for detailed wiring information. *Magnet activated sensor test A magnet can be used to test the sensor without opening the lid of the Pointek CLS300 digital version. Bring the magnet close to the test area indicated on the enclosure. The sensor test starts and finishes automatically after 0 seconds. Pointek CLS300 connections Siemens I 0 Update /207 /6
Pointek CLS Specials Selection and ordering data Pointek Specials ) Pointek Specials ) CLS00 Polycarbonate Lid and asket, KM Kit, sensor for cable units, PPS, digital, KM A5E063678 Kit, sensor for cable units, PPS, standard, KM A5E063679 Kit, sensor for cable units, PPS, digital, KM A5E063680 Kit, Lid and gasket, CLS00 enclosure version CLS00 Miscellaneous Parts Custom length of cable is available only for 7ML550-xxxx and 7ML550-xxx5x 2) CLS200 asket (IP65), Synprene A5E06367 Kit, sensor for cable units, PVD, standard, KM Kit, sensor for cable units, PVD, digital, KM Kit, sensor for cable units, PVD, standard, KM Kit, sensor for cable units, PVD, digital, KM A5E06368 A5E063682 A5E063683 A5E06368 CLS200 Mounting Bracket, 36L stainless steel Spare gasket, enclosure version (IP65 versions only) A5E063672 CLS200 asket (IP68), Silicone Spare mounting bracket A5E063685 CLS200 PROIBUS Connector (IP65) Spare gasket, enclosure version (IP68 versions) A5E063673 CLS200 Blind Lid Spare, PROIBUS connector (IP65 versions only) A5E063686 CLS200 Miscellaneous Parts CLS200 with KM O-rings (any version) 2) CLS200 Electronics Test magnet, digital version 7ML830-JE Spare aluminum blind lid (for standard versions only) CLS200 Lid with window A5E06367 Amplifier/power supply kit, standard version Amplifier/power supply, digital version LCD display, digital version A5E032568 7ML830-J 7ML830-JK CLS300 Cable Extensions, 36L stainless steel Spare aluminum lid with window CLS200 Sensor Kit for cable units A5E063676 Kit, stainless steel cable extension, m, A5E063688 Kit, stainless steel cable extension, 3 m, A5E063689 Kit, stainless steel cable extension, 5 m, A5E063690 Kit, sensor for cable units, PPS, Standard, KM A5E063677 Kit, stainless steel cable extension, 0 m, A5E06369 Kit, stainless steel cable extension, 5 m, A5E063693 Kit, stainless steel cable extension, 20 m, A5E063695 /62 Siemens I 0 Update /207