INSTALLATION INSTRUCTIONS Accessory Application Publications No. P/N 08V31-SDA-102 2007 ACCORD 4-DOOR AII 32672 Issue Date JULY 2006 NOTE: Fog lights can be installed in a vehicle equipped with a factory outside temperature gauge; fog lights cannot be installed on a vehicle equipped with an accessory outside temperature gauge. Fog light harness PARTS LIST Right fog light Switch harness Left fog light Right bracket Fog light switch Relay (black) Left bracket Fuse label Right trim 4 Self-tapping screws, 5 x 16 mm Left trim 2 Washer-screws, 5 x 16 mm 4 Step screws, 4 mm 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 32672 (0607) 08V31-SDA-1020-91 1 of 17
2 Ground bolts Washer 2 Washer-bolts, 6 x 16 mm TOOLS AND SUPPLIES REQUIRED #2 Phillips screwdriver Small flat-tip screwdriver 10 mm Combination wrench 10 mm Socket Ratchet Measure Eye protection (face shield, safety goggles, etc.) File Utility knife 2 Washer-screws, 4 x 8 mm Illustration of the Fog Lights Installed on the Vehicle 24 Wire ties 4 Short wire ties Relay bracket 2 Screw locks RIGHT FOG LEFT 4 Spring nuts 5801500Y Fuse (20A) Flange nut INSTALLATION Customer Information: The information in this installation instruction is intended for use only by skilled technicians who have the proper tools, equipment, and training to correctly and safely add equipment to your vehicle. These procedures should not be attempted by do-it-yourselfers. Corrugated tube 2 of 17 AII 32672 (0607) 2006 American Honda Motor Co., Inc. - All Rights Reserved.
1. Make sure you have the anti-theft code for the radio, then write down the frequencies for the preset buttons. 2. Open the hood. Disconnect the negative cable from the battery. 3. Remove the radiator cover (ten clips and four retaining tabs). 5. Remove the air duct cover (two clips), and pull it out toward you. Remove the air duct by pulling it out toward you. L4 Model: CLIPS (2) AIR DUCT COVER CLIPS (10) RETAINING TAB RADIATOR COVER AIR DUCT 4. Remove the hood latch cover (one clip). V6 Model: CLIP CLIP HOOD LATCH COVER AIR DUCT COVER 5613010P AIR DUCT 2004020T 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 32672 (0607) 3 of 17
6. Remove and discard the fog light cover from the front bumper (five retaining tabs). 8. Route the 2-pin connector end of the fog light harness in front of the radiator along the vehicle harness. BUMPER GROUND TERMINAL HOOD LATCH BRACKET GROUND BOLT WASHER RETAINING TAB (5) COVER (Discard.) 5411201Y BOLT (Discard.) 5411021P 7. Route the fog light harness 2-pin connector through the front bulkhead and alongside the vehicle harness. 2-PIN 9. Remove and discard the lower bolt that secures the hood latch bracket. Using one ground bolt and the washer supplied, attach the fog light harness ground terminal to the hood latch bracket. 10. On the left side of the vehicle, secure the fog light harness to the vehicle harness with five wire ties in the areas shown. Push the fog light harness clip into the hole in the body panel. HOLE 5411010P CLIP 5411031P 4 of 17 AII 32672 (0607) 2006 American Honda Motor Co., Inc. - All Rights Reserved.
11. On the right side of the vehicle, secure the fog light harness to the vehicle harness with a wire tie at the green tape. 14. Remove the two bolts that fasten the under-hood fuse/relay box. S FUSE/ BOX BOLTS BOLT WIRE TIE WIRE TIE GREEN TAPE (Do not allow the harness to contact the air conditioner pipe.) 12. Secure the fog light harness to the vehicle harness with three wire ties. 13. If equipped, remove the sub fuse box (one retaining tab). SUB FUSE BOX 5411042P AIR CLEANER HOUSING COVER BOLT (Remove.) 15. Remove the one bolt that fastens the air cleaner housing cover. 16. Release the six retaining tabs, and remove the under-hood fuse/relay box under cover. FUSE/ BOX RETAINING TABS (6) RETAINING TAB 4603010Y FUSE/ BOX UNDER COVER 4803030Y 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 32672 (0607) 5 of 17
17. Raise the under-hood fuse/relay box. 19. Unplug the vehicle 14-pin and 20-pin connectors from the under-hood fuse/relay box. Release the FUSE/ BOX (Raise.) lock on the vehicle 14-pin connector, and insert the fog light harness blue wire terminal into the vehicle 14-pin connector. Reattach the lock on the 14-pin connector. 14-PIN UNDER- HOOD FUSE/ BOX FUSE/ BOX UNDER COVER 4803040Y 18. Lift up the air cleaner housing cover, and route the other end of the fog light harness toward the engine alongside the vehicle harness. 14-PIN 20-PIN View from back side RETAINER BLUE/RED TERMINAL 20-PIN BLUE TERMINAL LOCK Lift. Harness side view Harness side view FUSE/ BOX 14-PIN AIR CLEANER HOUSING COVER 5411050P 20-PIN TERMINALS (2) 5531021P 20. Release the lock on the vehicle 20-pin connector, and insert the fog light harness blue/red wire terminal into the vehicle 20-pin connector. Reattach the lock on the 20-pin connector. 21. Plug the vehicle 14-pin and 20-pin connectors into the under-hood fuse/relay box. 6 of 17 AII 32672 (0607) 2006 American Honda Motor Co., Inc. - All Rights Reserved.
22. Secure the fog light harness to the vehicle harness with one short wire tie in the area shown. FUSE/ BOX FUSE/ BOX UNDER COVER SHORT FOG 23. Reinstall the under-hood fuse/relay box under cover. Be careful not to pinch the wires. 4804010Y 25. Under the under-hood fuse/relay box, locate the vehicle 3-pin connector blue-taped to the vehicle harness, and remove the blue tape to free the connector. Connect the fog light harness 3-pin connector into the 3-pin connector you just freed. Secure the fog light harness to the vehicle harness with four wire ties in the area shown. A/T Model: UNDER- HOOD FUSE/ BOX BLUE- TAPE (Remove.) 3-PIN FOG WIRE TIE 24. Wrap the corrugated tube around the vehicle harness, and secure it with the three short wire ties. 3-PIN 5411270Y M/T Model: UNDER- HOOD FUSE/ BOX 3-PIN BLUE- TAPE (Remove.) (Fold back.) CORRUGATED TUBE FOG SHORT 4412050Y 3-PIN 5411280Y 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 32672 (0607) 7 of 17
NOTE: If the 3-pin connector is already used by another accessory, locate the 3-pin connector taped to that other accessory harness. Remove the tape and dummy connector from that other accessory harness. Plug the fog light harness 3-pin connector into that other accessory harness. 3-PIN OTHER ACCESSORY 3-PIN 3-PIN 27. Plug the fog light harness 4-pin connector into the relay, and install the relay bracket to the vehicle frame.. L4 Model: Install the relay bracket to the vehicle frame with the washer-bolt supplied. If equipped with the vehicle bracket, remove the mounting bolt that secures the vehicle bracket, and attach the relay bracket using the vehicle bracket bolt. BRACKET (If equipped.) WASHER-BOLT or MOUNTING BOLT (If equipped with the vehicle bracket, reuse the mounting bolt.) WIRE TIE FRAME BRACKET OTHER ACCESSORY 3-PIN 26. Install the relay onto the relay bracket with one washer-bolt and one flange nut. 4-PIN 5411300Y BRACKET V6 Model: Install the relay bracket to the vehicle frame with the washer-bolt supplied. FLANGE NUT WASHER- BOLT BRACKET FRAME WASHER- BOLT (black) 5411290Y 4-PIN 5411310Y 8 of 17 AII 32672 (0607) 2006 American Honda Motor Co., Inc. - All Rights Reserved.
28. Secure the fog light harness to the vehicle harness with three wire ties in the areas shown. 30. Attach the 20A fuse label over the No.10 spot of the under-hood fuse/relay box cover. Reinstall the under-hood fuse/relay box cover. FUSE LABEL (20A) FUSE/ BOX COVER No.10 29. Remove the under-hood fuse/relay box cover (four retaining tabs), and install the 20A fuse (provided) into the No. 10 slot of the relay box. Installing Fog Lights (Left Side) 31. Using a utility knife, cut the front bumper in the areas shown. Cut out. FUSE/ BOX COVER RETAINING TABS (4) UTILITY KNIFE FUSE (20A) BUMPER Cut out. 5411210Y FUSE (20A) FUSE/ BOX FUSE/ BOX 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 32672 (0607) 9 of 17
32. Slide two spring nuts onto the front bumper from the inner side. SPRING NUT BUMPER 34. Install the left fog light on the left fog light trim using two 4 mm step screws and one 4 x 8 mm washer-screw. LEFT FOG TRIM 4 mm STEP SCREW 4 mm STEP SCREW 4 x 8 mm WASHER- SCREW LEFT FOG 5411220Y 33. Install the left fog light bracket onto the front bumper with two 5 x 16 mm self-tapping screws. BUMPER 5411240Y 35. Install the 5 x 16 mm washer-screw and screw lock on the left fog light trim as shown. LEFT FOG TRIM 5 x 16 mm SELF- TAPPING SCREW LEFT FOG BRACKET 5411231Y SCREW LOCK 5 x 16 mm WASHER- SCREW 5411250Y 10 of 17 AII 32672 (0607) 2006 American Honda Motor Co., Inc. - All Rights Reserved.
36. Install the fog light harness clip on the left fog light bracket. Routing the Switch Harness 40. Remove the driver s dashboard lower cover: LEFT FOG BRACKET CLIP 2-PIN Remove the one self-tapping screw. Release the four clips on the left side first by pulling out on the driver s dashboard lower cover. BUMPER After releasing the four clips, insert a flat-tip screwdriver between the clip and the dashboard frame. Gently twist the screwdriver to release the clip. Release the two clips on the right side last. Unplug the vehicle connector, and remove the lower cover. RETAINING TAB 5 x 16 mm WASHER- SCREW INSTALLED IN STEP 35 LEFT FOG 5411262Y CLIP (Release these clips first.) 37. Connect the fog light harness 2-pin connector to the left fog light. 38. Align the two retaining tabs on the left fog light trim with the corresponding slots in the front bumper, and install the left fog light onto the front bumper using the 5 x 16 mm washer-screw that you installed in step 35. 39. Repeat steps 31 through 38 to install the right fog light. CLIPS (7) DRIVER S DASHBOARD LOWER COVER SELF- TAPPING SCREW FLAT-TIP SCREWDRIVER CLIP (Release these clips last.) FRAME CLIP (Release the clip by inserting a flattip screwdriver between the clip and the dashboard frame, and twist the screwdriver to release the clip.) 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 32672 (0607) 11 of 17
41. If equipped, remove the driver s dashboard under cover (three clips, one pin, and one holder). HOLDER NOTE: If the fuse box 6-pin connector is already being used by another accessory, unplug the 6-pin connector from the under-dash fuse/relay box. Locate the 6-pin connector taped to the switch harness. Remove the dummy connector from the switch harness. Plug the other accessory harness 6-pin connector the into switch harness, and plug the switch harness 6-pin connector into the underdash fuse/relay box. 6-PIN DUMMY OTHER ACCESSORY 6-PIN PIN CLIPS (3) DRIVER S DASHBOARD UNDER COVER 42. Plug the switch harness 6-pin connector into the 6-pin connector in the under-dash fuse/relay box. 6-PIN UNDER-DASH FUSE/ BOX 43. Route the switch harness 5-pin connector (blue) along the vehicle harness to the body panel opening. Secure the switch harness to the vehicle harness with one wire tie in the area shown. BODY PANEL OPENING Front view 6-PIN CONNECTION POSITION UNDER-DASH FUSE/ BOX 5411330Y 5-PIN (Blue) 5411340Y 12 of 17 AII 32672 (0607) 2006 American Honda Motor Co., Inc. - All Rights Reserved.
44. Behind the steering hanger pipe, locate the 2-pin connector blue-taped to the vehicle harness. Connect the switch harness 2-pin connector to the vehicle 2-pin connector. 45. On the left of the steering shaft, locate the 3-pin connector black-taped to the vehicle harness, and plug the switch harness 3-pin connector in the 3-pin connector. 2-PIN STEERING HANGER PIPE 3-PIN STEERING SHAFT 2-PIN 3-PIN 5411350Y NOTE: If the 2-pin connector is already being used by another accessory, locate the 2-pin connector taped to that other accessory harness. Plug the switch harness 2-pin connector into the other accessory harness. NOTE: If the 3-pin connector is already being used by another accessory, locate the 3-pin connector taped to that other accessory harness. Remove the dummy connector from that other accessory harness. Plug the switch harness 3-pin connector into the other accessory harness. OTHER ACCESSORY 2-PIN 2-PIN 3-PIN 2-PIN 5411360Y DUMMY OTHER ACCESSORY 3-PIN 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 32672 (0607) 13 of 17
46. Secure the switch harness to the vehicle harness with six wire ties in the areas shown. 48. If equipped, reinstall the driver s dashboard under cover. HOLDER CLIPS (3) DRIVER S DASHBOARD UNDER COVER PIN 47. Remove the switch lid from the driver s side dashboard lower cover, and install the fog light switch in the driver s dashboard lower cover. HOLE 49. Plug the switch harness 5-pin connector (blue) into the fog light switch, plug in the two vehicle connectors, then reinstall the dashboard lower cover. 5-PIN (blue) LID DRIVER S DASHBOARD LOWER COVER DRIVER S DASHBOARD LOWER COVER 14 of 17 AII 32672 (0607) 2006 American Honda Motor Co., Inc. - All Rights Reserved.
50. Check that all wire harnesses are routed properly and all connectors are plugged in. 51. Reinstall all removed parts. Check that all clips and fasteners are installed securely. 52. Reconnect the negative cable to the battery. USE AND CARE How to Operate Fog Lights Turn the light switch to the on position (headlights on low beam ). Press the fog light switch (indicator is on). The fog light lenses can cloud when the outside temperature is cold; this is normal and should go away in warm weather. Fog Light Aiming Adjustment 53. Adjust the fog light: Adjust the aiming according to local laws and regulations. To adjust, turn the aiming adjustment screw in or out until the correct aiming is obtained. 54. Reset the clock, and reset the radio station presets. 55. Do the ECU idle learn procedure. Make sure all electrical items are turned off. Start the engine. Hold the engine speed at 3,000 rpm with no load (in Park or neutral) until the radiator fan comes on. Let the engine idle for about 5 minutes with the throttle fully closed and with all electrical items off. NOTE: If the radiator fan comes on during this step, the time when it is operating must not be included in the 5 minutes. NOTE: Whenever the battery is disconnected, the driver s window AUTO function is disabled. 56. Start the engine. Push down on the driver s window switch until the window is fully open. 57. Pull up on the driver s window switch fully to close the window completely, then hold the switch for 2 seconds. 58. Test the driver s window AUTO function. To raise To lower PHILLlPS SCREWDRIVER AIMING ADJUSTMENT GEAR PHILLlPS SCREWDRIVER 5411371Y 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 32672 (0607) 15 of 17
BULB REPLACEMENT 1. Loosen the screw inside the hole of the fog light trim, and pull the fog light trim toward you. 2. Disconnect the fog light harness 2-pin connector, and remove the fog light from the front bumper. 4. Install the new bulb into the socket. BUMPER Use only a genuine Honda halogen light bulb of specified wattage. Rating: 12V 55W H11 Halogen Light Bulb P/N 33165-S5A-003 Do not touch the bulb. Oily or greasy substances on the bulb can shorten its service life due to the heat produced when the bulb is turned on. If the bulb is accidentally touched, wipe it clean with a soft cloth that has been dampened with a denatured alcohol or a mind detergent solution. Align the tab on the fog light with the cutout in the bulb when installing the new bulb. If not aligned, the fog light may annoy oncoming drivers. SCREW LEFT FOG 5411383Y 3. Remove the bulb. SOCKET FOG NEW BULB 5411400Y 5. Reinstall the removed parts in the reverse order of removal. Check that the wire harnesses are not pinched. Be sure to tighten the screw securely. 6. Check the operation of the fog light; adjust the aiming if necessary. BULB 5411390Y 16 of 17 AII 32672 (0607) 2006 American Honda Motor Co., Inc. - All Rights Reserved.
CIRCUIT DIAGRAM HOT WITH HEAD IN HAED,AND DIMMER IN HIGHT Under-hood Relay UNDER-DASH Box FUSE/ BOX HOT IN COMBINATION OR FR RED/BLK WHT/GRN HOT WITH HEAD IN HAED FUSE/ Fog BOX Light Fuse BATTERY HOT AT ALL 20 A 20A TIMES MODULE FOG CONTROL CIRCUIT LEFT RED/GRN BLU/RED BLU/RED BLU/YEL RIGHT HOT WITH HEAD IN PARK OR HEAD GRN RED/BLK 2 RED Illumination Control BLU BLU 1 2 GRN RED Relay DASH 1 BRIGHTNESS CONTROLLER BLK Relay 1:INDICATOR 2:ILLUMINATION Switch 1=Indicato 2=Switch Illumination BLU/YEL BLK Front Fog Light BLK BLK BLK BLK 5412070P OFF BLK BLACK BRN BROWN YEL YELLOW ORN ORANGE BLU BLUE PUR PURPLE GRN GREEN NAT NATURAL OFF Low Hi RED RED PNK PINK WHT WHITE GRY GRAY OFF ON - - - - - - ON - LT BLU BLUE LT GRN GREEN 2006 American Honda Motor Co., Inc. - All Rights Reserved. AII 32672 (0607) 17 of 17