HepcoMotion Ball Bushings Range www.hepcomotion.com
Contents Super Ball Bushing - European Stanar SBE - Super European Close SBEO - Super European Open CS - Super European Pillow Block Close CSO - Super European Pillow Block Open 2 3 4 5 Stanar Ball Bushing LME - Stanar European Close LME-OP - Stanar European Open LM - Stanar Japanese Close LM-OP - Stanar Japanese Open 6-7 6-7 8-9 8-9 Flange Housing LMF - Single Roun Flange LMK - Single Square Flange LMF-L - Extene Length Roun Flange Units LMK-L - Extene Length Square Flange Units LMEL - Extene Length B411 Bushing 1-11 1-11 12-13 12-13 14 HepcoMotion Precision Linear Shaft Metric Shaft Support Rails Aluminium Shaft Support Housing an Shaft Tolerance Assembly Loa / Life Lubrication 15 16 17 18-19 18-19 2 21
HepcoMotion Stanar Ball Bushings Stanar ball bushings from HepcoMotion offer imensional interchangeability with all major manufacturers an incorporate a rigi steel outer sleeve with between 3 an 6 ball circuits epening on size. Ball retainers are mae from high grae polyamie for superior performance an low friction. Loa Carrying Row Non-loa Carrying Row Harene an Groun Outer Sleeve Shaft Retainer Ball Retaining Ring Fig 1. Linear Ball Bushing En Seal HepcoMotion Super Ball Bushings Super ball bushings from HepcoMotion offer approximately 3 times loa capacity which equates to 27 times the life of stanar ball bushings with the same overall imensions. These high quality units consist of harene steel segmente loa bearing plates with precision groun ball tracks combine with a +/-.5 egree self alignment feature. This ensures a uniform loa istribution over the entire row of balls, preventing point loaing that shortens life. Self Alignment Feature The outer surface of the steel loa bearing plates are esigne with a curve surface that in turn allows the bushing to absorb misalignment cause by inaccuracies between the shaft an ball bushing. In aition to ensuring equal loa istribution, the feature provies smooth entry an exit of the balls in an out of the loaing area. The self alignment feature requires two super ball bushings to be mounte to one shaft in a conventional two parallel shaft arrangement. Super ball bushings are interchangeable with the ISO stanar. (All main imensions, outsie iameter, bore an length are the same). Super ball bushings will reuce preparation an assembly time, as any shaft eflection an inaccuracies in the machining process will be accommoate by the self alignment feature. Easy entry an exit ball feature. Ball retainers are mae from a high grae polyamie maintaining low friction over the entire travel length. Friction coefficient of.1 with oil lubrication. Can operate at temperatures up to 1 C an spees up to 3m/sec. Life (27X) Loa capacity (3X).5.5 HepcoMotion Super Ball Bushing Conventional Ball Bushing Fig 2. Comparing Life an Loa Capacity Fig 3. +/-.5 º of Self-Alignment 1
SBE type - Super European Ball Bushing (self aligning) Close Type.5 3 D1 D.5 3 B2 B1 B With Two Seals (Stock Range) Dimensions Shaft With One Seal Without Seal D D1 B B1 B2 No. Ball Rows Basic Loa Ratings SBE16UU SBE16U SBE16 26 24.9 36 24.6 1.3 16 5 1176 67 26 SBE2UU SBE2U SBE2 32 3.5 45 31.2 1.6 2 6 2352 1254 6 SBE25UU SBE25U SBE25 4 38.5 58 43.7 1.85 25 6 458 2195 12 SBE3UU SBE3U SBE3 47 44.5 68 51.7 1.85 3 6 5586 2959 184 SBE4UU SBE4U SBE4 62 58.5 8 6.3 2.15 4 6 931 4312 342 SBE5UU SBE5U SBE5 75 71.5 1 77.3 2.65 5 6 1372 6762 586 yn. C stat. Co Weight (g) 2
SBEO type - Super European Ball Bushing (self aligning) Open Type.5 3 D1 D.5 3 B2 B1 B E θ With Two Seals (Stock Range) Dimensions Angle With One Seal Without Seal D D1 B B1 B2 E θ Shaft No. Ball Rows Basic Loa Ratings SBEO16UU SBEO16U SBEO16 26 24.9 36 24.6 1.3 9 68 16 4 1176 67 2 SBEO2UU SBEO2U SBEO2 32 3.5 45 31.2 1.6 9 55 2 5 2352 1254 5 SBEO25UU SBEO25U SBEO25 4 38.5 58 43.7 1.85 11.5 57 25 5 458 2195 1 SBEO3UU SBEO3U SBEO3 47 44.5 68 51.7 1.85 14 57 3 5 5586 2959 154 SBEO4UU SBEO4U SBEO4 62 58.5 8 6.3 2.15 19.5 56 4 5 931 4312 286 SBEO5UU SBEO5U SBEO5 75 71.5 1 77.3 2.65 22.5 54 5 5 1372 6762 486 yn. C stat. Co Weight (g) 3
CS type - Super European Ball Bushing Pillow Block Close Type (with 1pc self aligning SBE ball bushing) K W B±.2 4 - S1 L C±.2 G T b h±.2 F E±.2 4 - S2 Dimensions Mounting Dimensions h E W L F G T B C K b S1 S2 Shaft No. Ball Rows Basic Loa Ratings CS16UUB 22 26.5 53 43 42 29 1 4 26 6.5 13 M6 M5 16 5 1176 67 24 CS2UUB 25 3 6 54 5 34 12 45 32 7.5 18 M8 M6 2 6 2352 1254 34 CS25UUB 3 39 78 67 6 4 15 6 4 9 22 M1 M8 25 6 458 2195 636 CS3UUB 35 43.5 87 79 7 48 17 68 45 9.5 22 M1 M8 3 6 5586 2959 97 CS4UUB 45 54 18 91 9 62 22 86 58 11 26 M12 M1 4 6 931 4312 174 CS5UUB 5 66 132 113 15 68 25 18 5 12 34 M16 M12 5 6 1372 6762 2922 yn. C stat. Co Weight (g) 4
CSO type - Super European Ball Bushing Pillow Block Open Type (with 1pc self aligning SBEO ball bushing) E±.2 4 - S1 W L K B±.2 C±.2 h±.2 T b F h±.2 h1 θ 4-S2 Dimensions Mounting Dimensions h E W L F T h1 θ B C b S1 S2 Shaft No. Ball Rows Basic Loa Ratings yn. C stat. Co Weight (g) CSO16UUB 22 26.5 53 43 35 8 9 68 4 26 13 M6 M5 16 4 1176 67 16 CSO2UUB 25 3 6 54 42 1 9 55 45 32 18 M8 M6 2 5 2352 1254 28 CSO25UUB 3 39 78 67 51 13 11.5 57 6 4 22 M1 M8 25 5 458 2195 552 CSO3UUB 35 43.5 87 79 6 15 14 57 68 45 22 M1 M8 3 5 5586 2959 846 CSO4UUB 45 54 18 91 77 2 19.5 56 86 58 26 M12 M1 4 5 931 4312 1516 CSO5UUB 5 66 132 113 88 25 22.5 54 18 5 34 M16 M12 5 5 1372 6762 2546 5
LME Series - Stanar European Ball Bushing LME LME OP L B W W D D1 LME Series Basic Loa Ratings Working Bore Diameter Stanar Type Open Type yn. No. of Ball No. of Ball C Circuit Circuit LME5UU 4 - - 2 26 5 LME8UU 4 - - 26 4 8 LME12UU 4 LME12UUOP 3 41 59 12 LME16UU 5 LME16UUOP 4 77 117 16 LME2UU 5 LME2UUOP 4 86 137 2 LME25UU 6 LME25UUOP 5 98 156 25 LME3UU 6 LME3UUOP 5 156 274 3 LME4UU 6 LME4UUOP 5 215 41 4 LME5UU 6 LME5UUOP 5 328 793 5 LME6UU 6 LME6UUOP 5 47 999 6 stat. Co 6
LME Series - Stanar European Ball Bushing h1 θ LME LME OP Dimensions D L B W D1 h1 θ Weight (g) (µm) LME5UU - 12 22 14.5 1.1 11.5 - - 12 LME8UU - 16-8 25 16.5 1.1 15.2 - - 2 LME12UU LME12UUOP 22 32 22.9 1.3 21 -.2 -.2 7.5 78 41 LME16UU LME16UUOP 26-9 36 24.9 1.3 24.9 1 78 57 LME2UU LME2UUOP 32 45 31.5 1.6 3.3 1 6 91 LME25UU LME25UUOP 4-11 58 44.1 1.85 37.5 12.5 6 215 LME3UU LME3UUOP 47 68 52.1 1.85 44.5 12.5 5 325 LME4UU LME4UUOP 62 8 -.3 6.6 -.3 2.15 59 16.8 5 75 LME5UU LME5UUOP 75-13 1 77.6 2.65 72 21 5 113 LME6UU LME6UUOP 9-15 125 -.4 11.7 -.4 3.15 27.2 27.2 54 222 7
LM Series - Stanar Japanese Ball Bushing LM LM OP L B W W D D1 LM Series Basic Loa Ratings Working Bore Diameter Stanar Type Open Type yn. No. of Ball No. of Ball C Circuit Circuit LM4UU 4 - - 88 18 4 LM5UU 4 - - 167 26 5 LM6UU 4 - - 2 26 6 LM8SUU 4 - - 17 22 8 LM8UU 4 - - 26 4 8 LM1UU 4 - - 37 54 1 LM12UU 4 LM12UUOP 3 41 59 12 LM13UU 4 LM13UUOP 3 5 77 13 LM16UU 5 LM16UUOP 4 77 117 16 LM2UU 5 LM2UUOP 4 86 137 2 LM25UU 6 LM25UUOP 5 98 156 25 LM3UU 6 LM3UUOP 5 156 274 3 LM35UU 6 LM35UUOP 5 166 313 35 LM4UU 6 LM4UUOP 5 215 41 4 LM5UU 6 LM5UUOP 5 382 793 5 LM6UU 6 LM6UUOP 5 47 999 6 stat. Co 8
LM Series - Stanar Japanese Ball Bushing h1 θ LM LM OP LM4UU - 8-9 LM5UU - 1-8 Dimensions D L B W D1 h1 θ (µm) 12 -.12 15 -.12 Weight (g) - - - - - - 1.9 LM6UU - 12 19 13.5 1.1 11.5 - - 8 LM8SUU - 15 17 11.5 1.1 14.3 - - 11-11 LM8UU - 15 24 17.5 1.1 14.3 - - 16 -.2 LM1UU - 19 29 22 1.3 18 - - 3 -.2 LM12UU LM12UUOP 21 3 23 1.3 2 8 8 31.5 LM13UU LM13UUOP 23-13 32 23 1.3 22 9 8 43 1.2 1.1 9.6 - - 4 LM16UU LM16UUOP 28 37 26.5 1.6 27 11 8 69 LM2UU LM2UUOP 32 42 3.5 1.6 3.5 11 6 87 LM25UU LM25UUOP 4-16 59 41 1.85 38 12 5 22 LM3UU LM3UUOP 45 64 44.5 1.85 43 15 5 25 LM35UU LM35UUOP 52 7 49.5 2.1 49 17 5 39 LM4UU LM4UUOP 6 8 -.3 6.5 -.3 2.1 57 2 5 585-19 LM5UU LM5UUOP 8 1 74 2.6 76.5 25 5 158 LM6UU LM6UUOP 9-22 11 85 3.15 86.5 3 5 2 9
LMF/K Series - Stanar Flange Units LMF LMK L 1 H h 2 D B Circular type Square type No. of Ball Circuit Weight (g) Basic Loa Ratings Dyn. C Stat. Co Working Bore Diameter LMF6UU LMK6UU 4 26.5 2 26 6 LMF8SUU LMK8SUU 4 34. 17 22 8 LMF8UU LMK8UU 4 4. 26 4 8 LMF1UU LMK1UU 4 78. 37 54 1 LMF12UU LMK12UU 4 76. 41 59 12 LMF13UU LMK13UU 4 94. 5 77 13 LMF16UU LMK16UU 5 134. 77 117 16 LMF2UU LMK2UU 5 18. 86 137 2 LMF25UU LMK25UU 6 34. 98 156 25 LMF3UU LMK3UU 6 46. 156 274 3 LMF35UU LMK35UU 6 795. 166 313 35 LMF4UU LMK4UU 6 154. 215 41 4 LMF5UU LMK5UU 6 22. 382 793 5 LMF6UU LMK6UU 6 296. 47 999 6 1
LMF/K Series - Stanar Flange Units K PCD PCD LMF LMK Dimensions D L B H PCD K 1 x 2 x h Circular type Square type (µm) LMF6UU LMK6UU 12 19 28 5 2 22 3.4 x 6.5 x 3.3 LMF8SUU LMK8SUU 15-11 17 32 5 24 25 3.4 x 6.5 x 3.3 LMF8UU LMK8UU 15 24 32 5 24 25 3.4 x 6.5 x 3.3 LMF1UU LMK1UU 19 29 4 6 29 3 4.5 x 8 x 4.4 LMF12UU LMK12UU 21 -.2 3 42 6 32 32 4.5 x 8 x 4.4-13 LMF13UU LMK13UU 23 32 43 6 33 34 4.5 x 8 x 4.4 -.2 LMF16UU LMK16UU 28 37 48 6 38 37 4.5 x 8 x 4.4 LMF2UU LMK2UU 32 42 54 8 43 42 5.5 x 9.5 x 5.4 LMF25UU LMK25UU 4-16 59 62 8 51 5 5.5 x 9.5 x 5.4 LMF3UU LMK3UU 45 64 74 1 6 58 6.6 x 11 x 6.5 LMF35UU LMK35UU 52 7 82 1 67 64 6.6 x 11 x 6.5 LMF4UU LMK4UU 6 8-19 -.3 96 13 78 75 9 x 14 x 8.6 LMF5UU LMK5UU 8 1 116 13 98 92 9 x 14 x 8.6 -.3 LMF6UU LMK6UU 9 11 134 18 112 16 11 x 17.5 x 1.8-22 11
LMF/KL Series - Extene Length Flange Units LMF L LMK L L 1 H h 2 D B Circular Type Square Type No. of Ball Circuit Weight (g) yn. C Basic Loa Ratings stat. Co Working Bore Diameter LMF6LUU LMK6LUU 4 31 32 52 6 LMF8SLUU LMK8SLUU 4 53 43 78 8 LMF1LUU LMK1LUU 4 15 58 11 1 LMF12LUU LMK12LUU 4 1 65 12 12 LMF13LUU LMK13LUU 4 13 81 157 13 LMF16LUU LMK16LUU 5 187 123 235 16 LMF2LUU LMK2LUU 5 26 14 275 2 LMF25LUU LMK25LUU 6 515 156 314 25 LMF3LUU LMK3LUU 6 655 249 549 3 LMF35LUU LMK35LUU 6 97 265 647 35 LMF4LUU LMK4LUU 6 156 343 84 4 LMF5LUU LMK5LUU 6 35 68 159 5 LMF6LUU LMK6LUU 6 45 765 2 6 12
LMF/KL Series - Extene Length Flange Units K PCD PCD LMFL LMKL Circular Type Square Type D L B Dimensions H PCD K 1 x 2 x h LMF6LUU LMK6LUU 12 35 28 5 2 22 3.4x6.5x3.3 LMF8SLUU LMK8SLUU 15-13 45 32 5 24 25 3.4x6.5x3.3 LMF1LUU LMF12LUU LMK1LUU LMK12LUU 19 21 55 57 -.3 4 42 6 6 29 32 3 32 4.5x8x4.4 4.5x8x4.4 LMF13LUU LMK13LUU 23-16 61 43 6 33 34 4.5x8x4.4 LMF16LUU LMK16LUU 28 7 48 -.2 6 38 37 4.5x8x4.4 LMF2LUU LMK2LUU 32 8 54 8 43 42 5.5x9.5x5.4 LMF25LUU LMK25LUU 4-16 112 62 8 51 5 5.5x9.5x5.4 LMF3LUU LMK3LUU 45 123 74 1 6 58 6.6x11x6.5 LMF35LUU LMK35LUU 52 135 82 1 67 64 6.6x11x6.5 LMF4LUU LMK4LUU 6 -.4-19 154 96 13 78 75 9x14x8.6 LMF5LUU LMK5LUU 8 192 116 -.3 13 98 92 9x14x8.6 LMF6LUU LMK6LUU 9 211 134 18 112 16 11x17.5x1.8-22 (µm) 13
LMEL Series - Extene Length Ball Bushing L B W W D D1 LML Series No. of Ball Circuit Working Bore Diameter Dimensions D L B W D1 Weight (g) Basic Loa Ratings LME8LUU 4 8 16 45 33 1.1 15.2 31 43 78 LME12LUU 4 12 22-9 57 -.3 45.8 -.3 1.3 21 8 65 12 LME16LUU 5 16 26-11 7 49.8 1.3 24.9 145 123 235 LME2LUU 5 2 32 8 61 1.6 3.3 18 14 275 LME25LUU 6 25 4-13 112 82 1.85 38 44 156 314 LME3LUU 6 3 47 123 14.5 1.85 44.5 58 249 549 LME4LUU 6 4 62 154 -.4 121.2 -.4 2.15 59 117 343 84 LME5LUU 6 5 75-15 192 155.2 2.65 72 31 68 159 LME6LUU 6 6 9-2 (µm) yn. C stat. Co 211 17 3.15 86.5 35 765 2 14
Precision Linear Shaft Correct shaft selection is vital if maximum performance is to be achieve from our linear system. Hepco Precision Shaft has been evelope to provie excellent performance when use with either recirculating ball bushings or plain bearing technology. An extensive range of shaft materials are available an HepcoMotion offers a full machining facility with fast turnaroun. Other types of shaft available inclue: Specials (up to 15mm Ø). Tubing (Please enquire). Shaft Type: Metric Part Ref. Harness RC TOL Diameter Options 4 5 6 8 1 12 13 16 2 25 3 35 4 5 6 8 Metric Carbon Steel CK53 Harene an Groun NIMxx 6 h6 Metric Stainless Steel (4 series) Harene an Groun Metric Soft Stainless Steel (3 Series) Groun Metric Harcoat Anoise Aluminium NIMxx- SS NIMxx- SS316 NI- MAxx 5 h6 X h6 X h6 Shaft Type: Imperial Part Ref. Harness RC TOL Diameter Options 3/16 1/4 3/8 1/2 5/8 3/4 1 1 1/4 1 1/2 2 Imperial Carbon Steel CK53 Harene an Groun NILxx 6 Class L Imperial Stainless Steel (4 Series) Harene an Groun Imperial Soft Stainless Steel (3 Series) Groun NILxx- SS NILxx- SS316 5 Class L X Class L Imperial Harcoat Anoise Aluminium NILAxx X Class L 15
Metric Shaft Support Rails Shaft support rails will prevent shaft eflection uner loa an provie a high level of rigiity in orer to achieve optimum performance from your open type Hepco Ball Bushing or any other open recirculating or plain linear bushing. N M 72.5º Support Rails are of low overall height making them particularly suitable for use with Hepco Pillow Blocks. The stanar support rail is manufacture from aluminium alloy an comes in 6mm lengths only. These are then cut/butte together to fit to the overall length of the one piece shaft. H t O1 E A U1 O 2 U 2 V All types of shaft can be supplie rille for customer assembly or fitte to the support rails for ease of supply. For stanar 6mm aluminium support rails, X = half of T1 or T2. For support rails which require cutting/butting, please confirm Dimension X when orering. X T1/T2 X 6 +.5-1.5 X = 1/2 hole pitch T 1 or T 2 For Shaft Diameter H 1 ±.1 A V M O 1 U 1 N E t O 2 U 2 T1 T2 12 12 22 4 5 5.8 M4X2 4 8 29 4.5 M4 4 75 12 16 16 26 45 5 7 M5X2 5 9 33 7.6 M5 5 1 15 2 2 32 52 6 8.3 M6X25 6 11 37 8.6 M6 6 1 15 25 25 36 57 6 1.8 M8X3 8 15 42 9 M6 6 12 2 3 3 42 69 7 11 M1X35 1 17 51 1 M8 8 15 2 4 4 5 73 8 15 M1X4 1 19 55 9.5 M8 8 2 3 5 5 6 84 9 19 M12X45 12 21 63 11.2 M1 1 2 3 Orering Shaft 16 Shaft & Support Rail Fully Assemble Drille Shaft Only Support Rails Only Simply prefix the shaft reference with AU. Example AU NIM 2 X L2 T2 Simply state the shaft reference an a T1 or T2 epening upon shaft hole centres require. Example NIM 2 X L2 T2 Aluminium Support Rails (SR) supplie in lengths up to 2mm. Simply state whether T1 or T2 mounting hole spacing is require. Example Support Rail for 2mm Shaft T2 Hole Centre SR2 T2
Aluminium Shaft Supports E ±.5 P S O 2 U 2 ±.2 F G h B W L Nominal Shaft Diameter Major Dimensions h E W L F G P B S O 2 U 2 Weight (g) ASS1 1 17 18.5 37 1 3 5 18 28 4.5 M4 4 24 ASS12 12 2 21 42 15 35 5.5 2 32 5.5 M5 5 3 ASS16 16 25 25 5 15 42 6 26 4 5.5 M5 5 4 ASS2 2 3 3 6 2 5 8 32 45 5.5 M5 5 7 ASS25 25 35 37 75 25 58 9 38 6 6.6 M6 6 13 ASS3 3 4 42 84 3 68 1 45 68 9 M8 8 18 ASS4 4 5 54 18 3 86 12 56 86 11 M1 1 42 ASS5 5 6 65 13 4 1 14 8 18 11 M1 1 75 Machine Ens HepcoMotion can unertake shaft machining to stanar ens as shown below or specials to customers rawings. L2 Option A L2 Option B L2 Option C D D D Spigot One en L Both ens Unercut to DIN 76 Threae Spigot One en Both ens Drille an Tappe One en Both ens L2 Option D A/F D Please sen rawing Please sen rawing Single Flat One en Double Flat Both ens 17
Housing an Shaft Tolerance - Super Ball Bushing The recommene housing an shaft tolerances for Super Ball Bushings are shown in table 1. Table 1. Super Ball Bushing SBE/SBEO Outer Diameter (D) 16 26 2 32 25 4 3 47 4 62 +.21 +.25 +.3 Housing Bore (H7) Shaft Tol (h6) a a a 5 75 Assembly - Super Ball Bushing Use of a jig (see figure 5) is recommene for insertion into a housing. Care shoul be taken not to exert pressure on the ball retainer or seals. The ege of the housing bore must be chamfere. Correct alignment is essential in orer to prevent amage. D -.1 -.4 -.5 -.15 Fig 5. Use of a Jig 18
Housing an Shaft Tolerance - Stanar Ball Bushing The recommene housing an shaft tolerances for Stanar Ball Bushings are shown in table 2. Table 2. Stanar Ball Bushing LME/LME-OP Outer Diameter (D) Housing Bore (H7) Shaft Tol (h6) 5 12 +.18 8 16 12 22 +.21 16 26 2 32 25 4 +.25 3 4 5 47 62 +.3 75 6 9 +.35 a a a a a Assembly - Stanar Bull Bushing Possible mounting methos are illustrate in Figure 6. an Figure 7. with retaining rings an cover plates. Fig 6. Mounting With Retaining Rings Fig 7. Mounting With Cover Plates 19
Loa / Life Calculation Basic Dynamic Rating (C) The basic Dynamic Loa Rating (C) is the maximum continuous loa that can be applie to a bearing with a 9% probability that a working life of 5 km will be achieve. There are two key factors to the loa calculation that may nee to be applie epening on the application conitions. Harness factor (FH) Shaft harness factor (FH) The harness of the shaft shoul be 6 RC +/- 2, refer to figure 8 for shaft harness factors. Raceway Harness HRC Fig 8. Harness Factor (FH) Temperature factor (FT) FH FT L : Running istance life C : Basic ynamic loa rating P : Applie loa FH : Harness factor (figure 8.) FT : Temperature factor (figure 9.) (km) Temperature factor (FT) Linear motion system temperature C Fig 9. Temperature Factor (FT) Ball bushings in this range are esigne to work at a maximum temperature of 1 egrees C, for temperatures higher than this please apply the temperature factor as inicate in figure 9. Basic Static Loa Rating (Co) The Basic Static Loa Rating (Co) is the static loa that will permanently cause eformation of the bushing ball track equivalent to.1% of the ball iameter. It is goo practice to limit the maximum static force to a maximum of 8%. Short Stroke Life Reuction Where the stroke istance is less than a Ball Bushing length the calculate life will be reuce by up to 7%. 2
Lubrication For best performance, an to achieve a long an trouble free life, ball bushings require lubrication with either oil or grease. Grease Lubrication For grease lubrication the anticorrosive protection oil shoul be remove prior to assembly ensuring that the bearing is ry before applying grease. Grease shoul be applie irectly to the ball circuits prior to fitting, generally a lithium soap grease ISO viscosity grae 2 is recommene for general use. Oil Lubrication For oil lubrication it is not necessary to remove the anticorrosive protection from the bushing. The viscosity grae will be epenent on the operating temperature, please see the chart below. Operating Temp. -3 C ~ 5 C 5 C ~ 8 C Viscosity VG 15 ~ 46 VG 46 ~ 1 Fig 1. Two Assemble Bushings For most effective lubrication oil shoul be applie between two assemble bushings as shown in Figure 1 where seals are fitte only to the outsie of each bearing. Perioic checking of the installation is recommene whether oil or grease is use, in orer to check that the bushing is not running ry. 21
HepcoMotion Prouct Range GV3 Linear Guiance an Transmission System HDS2 Heavy Duty Slie System PRT2 Precision Ring an Track System HDRT Heavy Duty Ring Slies an Track System SL2 Stainless Steel Base Slie System HLG Hepco Linear Guies SBD Seale Belt Drive MCS Aluminium Frame an Machine Construction System HDLS Heavy Duty Driven Linear System DLS Linear Transmission an Positioning System HTS Telescopic Ball Bearing Slies HPS Powerslie-2 Guie Roless Cyliner MHD Heavy Duty Track Roller Guiance System DTS Driven Track System BSP Ballscrew Premier Vee Slie Linear Guiance Systems PDU2 Profile Driven Unit PSD12 Profile Screw Driven Unit For further information on HepcoMotion proucts please request our leaflet FPL HepcoMotion www.hepcomotion.com HepcoMotion - Deutschlan Bahnhofstraße 16 9537, Feucht, Deutschlan Tel: +49 () 9128 9271 Fax: +49 () 9128 9271 5 E-mail: info.e@hepcomotion.com HepcoMotion - Hea Office Lower Moor Business Park, Tiverton Way Tiverton, Devon, Englan EX16 6TG Tel: +44 ()1884 257 Fax: +44 ()1884 2435 E-mail: sales@hepcomotion.com HepcoMotion - España Alt e Gironella, 36-38 bajos ES-817, Barcelona, España Tel: +34 93 25 84 47 Fax: +34 93 28 62 14 E-mail: info.es@hepcomotion.com HepcoMotion - Benelux Berkvel 14A NL-579 AE Helmon, Neerlan Tel: +31 () 492 55129 Fax: +31 () 492 52815 E-mail: info.nl@hepcomotion.com HepcoMotion - France 64 Chemin e la Chapelle, Saint Antoine ENNERY, 953, France Tel: 1 34 64 3 44 Fax: 1 34 64 33 88 E-mail: info.fr@hepcomotion.com CATALOGUE No.Ball Bushings 1 UK 215 Hepco Slie Systems Lt. Reprouction in whole or part without prior authorisation from Hepco is prohibite. Although every effort has been mae to ensure the accuracy of the information in this catalogue, Hepco cannot accept liability for any omissions or errors. Hepco reserves the right to make alterations to the prouct resulting from technical evelopments. Many Hepco proucts are protecte by: Patents, Copyright, Design Right or Registere Design. Infringement is strictly prohibite an may be challenge in law. The Customer s attention is rawn to the following clause in Hepco s conitions of sale: It shall be the Customer s sole responsibility to ensure that goos supplie by Hepco will be suitable or fit for any particular application or purpose of the Customer, whether or not such application or purpose is known to Hepco. The Customer will be solely responsible for any errors in, or omissions from, any specifications or information the Customer provies. Hepco will not be oblige to verify whether any such specifications or information are correct or sufficient for any application or purpose. Hepco s full conitions of sale are available on request an will apply to all quotations an contracts for the supply of items etaile in this catalogue. HepcoMotion is the traing name of Hepco Slie Systems Lt. 22