Blohm+Voss Pipe Handling Equipment FPS 500-AIR Flush Power Slip Technical Documentation Original Instructions Manual 754000-AIR-D Rev 000, October 2012 Blohm + Voss Oiltools 1
GENERAL INFORMATION Warnings and Note WARNING: A warning indicates a definite risk of equipment damage or danger to personnel. Failure to observe and follow proper procedures could result in serious or fatal injury to personnel, significant property loss, or significant equipment damage. NOTE: A note indicates that additional information is provided about the current topics. WARNING: This technical documentation contains instructions on safety, installation, operation and maintenance for the Blohm + Voss Oil Tools tool. It must be studied before working with the tool. Improper / Unsafe Use The tool must only be used for the designated purpose. When using the tool, the rated load must never be exceeded. Intended use of this manual This manual is intended for use by field service, engineering, installation, operation, and repair personnel. Every effort has been made to ensure the accuracy of the information contained herein. Blohm + Voss Oil Tools, will not be held liable for errors in this material, or for consequences arising from misuse of this material. Anyone using service procedures or tools, whether or not recommended by Blohm + Voss Oil Tools, must be thoroughly satisfied that neither personal safety nor equipment safety will be jeopardized. Intellectual property All rights retained. No part of this document may be reproduced in any form (print, photocopy, microfilm or any other procedure) or be processed using an electronic system without written approval of Blohm + Voss Oil Tools. All information contained in this manual is based upon the latest product information available at any time of printing. Dependent on ongoing technical improvements (ISO 9001) Blohm + Voss Oil Tools reserves the right to change the design and specifications without announcement. The values specified in this manual represent the nominal values of a unit produced in series. Slight deviations in the case of the individual devices are possible. NOTE: In the event of problems that cannot be solved with the aid of this manual, please contact one of the addresses listed below. CE Marking The tool complies with the Machinery Directive 98/37/EC and 2006/42/EC For machines containing any hydraulic or pneumatic powered parts, the Directive 94/9/EC Equipment and protective systems in potentially explosive atmospheres applies. The marking is as follows: CE Ex II 2G T5 (hydraulic tools) or CE Ex II 2G T6 (pneumatic tools). Limited Warranty The warranty provided will be void if the tool is either: 1. Repaired or serviced by a service facility which was not authorised by Blohm + Voss Oil Tools. 2. Replacement parts not manufactured by Blohm+Voss Oil Tools are used. 3. Modifications were made to the tool which were not approved by Blohm+Voss Oil Tools. Manufacturer & Agents World wide Blohm + Voss Oil Tools Hermann-Blohm-Straße 2 20457 Hamburg Germany Phone: +49 40/3119-1826/1162 Fax: +49 40/3119-8194 oiltools@blohmvoss.com www.blohmvoss-oiltools.com Blohm + Voss Oil Tools, LLC 7670 Woodway, Suite 266 Houston, Texas 77063 United States of America Phone: +1-713-952 0266 Fax: +1-713-952 2807 bvot@blohmvoss.com www.blohmvoss-oiltools. com Premier Sea & Land Pte. Ltd. 1, Scotts Road #19-12 Shaw Centre Singapore 228208 Republic of Singapore Phone: +65-6734-7177 Fax: +65-6734-9115 enquiries@mtqpremier.com. sg 2
General safety issues WARNING: One should avoid creating ignition sources, like heat, as a result of the use of the tool with other tools or equipment. WARNING: Do not use the tool for any other purpose than given in this document within it`s specification. WARNING: Failure to conduct routine maintenance could result in equipment damage or injury to personnel. WARNING: Wear personal protection equipment while working with the equipment. WARNING: If any safety elements (like safety ropes, safety sheets, plates or washers) were disassembled due to maintenance work, do NOT re-use them. Always replace them with new safety elements. WARNING: All warning plates, signs and labels attached to the equipment must be observed. The warning plates, signs and labels must be present on the tool. Do not remove the labels. If they are missing, replacing is mandatory. WARNING: Any modification to the tool carried out without the approval of Blohm + Voss Oil Tools will void any warranty. WARNING: Using the tool with damaged or worn parts can create serious incidents. WARNING: It is not allowed to use any components which are of "non-b+v" origine, or use "non-oem" parts which are not approved by B+V. It will void any warranty and may effect the correct functioning of the tool and it's safety features. WARNING: The company operating the tool is responsible for evaluating safe and proper use of the tool in a hazard analysis. WARNING: The operating company is obligated to issue working instructions for safe use and supervise observance of these working instructions. WARNING: Every Employee, which operates, services, inspects or otherwise involved with the use of the tool in other areas has to ensure, that these actions are done by trained and by an Blohm + Voss Oil Tools authorized personnel, and should complete regular courses of training, to ensure proper use as well as safe operation, correct maintainance and inspection. WARNING: If necessary, a reasonable, additional supervisor should be appointed during operation. WARNING: Stay away from the tool during operation. In case it is remote operated it may make movements without warning. Safe handling WARNING Handles/grip points are marked by green paint. During operations these grips are the only places the tool can be handled safely. In all NON-green marked places there is a risk for injury. Automatic/ remote operated tools may not have any green painted grippoints. In this case it is not allowed to touch the tool while operating. Safe gripping points Warning sign PN 671638 General warning Warning sign PN 671642 Pay attention: Apply grease at least once a day. Warning sign PN 611524 Danger: Do not touch. Warning sign PN 671640-1 Pay attention: Do not place your hands between moving parts. Warning sign PN 671641 Pay attention: Risk of crushing. 3
Safety issues Power slips WARNING: Always ensure the slip segments are labelled with the same serial number. Never use segments with different numbers as they may cause the pipe to drop due to different wear patterns. WARNING: Under no circumstances should the slip assembly be raised while supporting load. If the slip assembly is lowered in place, the tool can bear the load of the tubular. Before raising the slip assembly, make sure that the tubular load is supported. The slip assembly must be released from any load before raising it. WARNING: You must neither assemble nor disassemble Slips, Guides, Inserts, etc. when the Tool is placed in the rotary table. WARNING: Never use the Power Slip/Spider/Elevator without guide plates. This can cause damage to the slips and lead to loss of pipes/tubular. WARNING: Make sure all slip segments are free in the up position when latching the elevator. If any of the segments are stuck in the down position, the elevator may not close properly. Safety issues automatic power slips/spiders/elevators Warning: ensure the connectors are from a male and female type to prevent faulty connections. Warning: pneumatic only before any maintenance work is carried out, make sure that no pressure is applied to the equipment and that the connecting lines are disconnected (if applicable). Safety issues spiders Warning: you must neither assemble nor disassemble slips, guides, inserts, etc. When the tool is placed obove the well center. WARNING: It must be ensured and controlled regularly that the back side of the slips are lubricated with enough grease. The quantity of grease must be related to the type of operation and type of mud. Failure to grease properly may lead to sticking slips. WARNING: Do never unlatch/ open the tool while a pipe is suspended in the tool; the pipe will be lost! 4
Positioning of Warning Signs 1 3 7 2 3 5 4 6 Item Qty. Part no. Description 1 3 671642 Grease Daily 2 2 671641 Squeeze Danger 3 2 671640 Hand Squeeze Danger 4 1 671638 Warning Sign B+V 5 1 613129 Technical Support 6 2 611524 Warning Sign 7 3 671644 Warning Sign Lubrication Warning 5
EC-DECLARATION OF CONFORMITY We, Blohm + Voss Oil Tools Hermann-Blohm-Strasse 2 20457 Hamburg Phone:+49(0)40 3119-1139 Fax:+49(0)40 3119-3305 declare that the product B+V Type FPS 500 pneumatic operated Flush Power Slip including Slips, Guide plates and Control Unit which is the subject of this declaration, is in conformity with the following standard(s) or normative documents 2006/42/EC: Machinery Directive from 31 December 2009. DIN EN ISO 12100 : Safety of machinery, part 1 and 2 DIN EN ISO 14121-1: Safety of machinery, Risk assessment Directive 94/9/EC: Devices and protection systems for intended use in explosive areas DIN EN 13463-1:2009-07: Non-electrical equipment for use in potentially explosive atmospheres ISO 14693/API 7K: Specification for Drilling and Well Servicing Equipment In case the product is hydraulically operated: Marking: II 2G T6 6
TABLE OF CONTENTS GENERAL INFORMATION 2 Warnings and Note 2 Intended use of this manual 2 Intellectual property 2 Improper / Unsafe Use 2 Manufacturer & Agents World wide 2 CE Marking 2 Limited Warranty 2 General safety issues 3 Safety issues Power slips 4 Safety issues automatic power slips 4 Safety issues spiders 4 Positioning of Warning Signs 5 EC-DECLARATION OF CONFORMITY 6 TABLE OF CONTENTS 7 1. DESCRIPTION 9 General 10 Features 10 Intend of use 10 Options 10 pneumatic connections 10 Rotary tables 10 Main assemblies 11 Improper / Unsafe Use 11 Limited Warranty 11 Identification 11 Technical Data 12 Options 13 Main Dimension 14 Insert Carrier grip Length 15 Drill Pipe and Casing 15 2. COMMISSIONING 17 Commissioning FPS 500 18 Scope of supply 18 Hydraulic Characteristics 18 Check and Lubrication 18 3. INSTALLATION 19 Lifting and transport 20 Pneumatic System 20 Pneumatic connections 20 Purging air 20 Schematic control diagram 21 Checking Guide Plates 22 Changing Slips 23 Changing Inserts 23 Pneumatic Connections 24 Function test 24 4. OPERATIONS 25 Safety 26 Operation 26 Removing the FPS when pipe is in the hole 26 Removing the FPS from drill pipe (in rotary) 26 Connecting and disconnecting of the pneu. hoses 26 Dis-connection hoses in slips up position 26 Handling the slip assembly during operation 27 (Emergency) opening the door 28 5. Maintenance and Inspection 29 General 30 Daily Lubrication 30 Grease daily 31 Grease quality 31 Inspection categories acc. to API RP 8B 32 Frequency 32 Periodic inspection 32 Non-periodic inspection 32 Inspection 32 Inspection of Hydraulic/Pneumatic System 32 Critical Load Inspection 32 Dismantling Inspection 33 Inspection check lists 34 Check List Category I 35 Check List Category II 37 Check List Category III 39 Check List Category IV 40 Wear data criteria 41 Critical Areas 42 Critical Areas Body 42 Critical Areas Slips 42 Critical Areas Door and Hinge Pin 42 Critical area drawings of lifting eyes 43 Handling, storage and transport 44 TABLE OF CONTENTS DESCRIPTION COMMISSIONING INSTALLATION DRAWINGS SIZE COMPONENTS MAINTENANCE & OPERATION INSPECTION 7
MAINTENANCE & TABLE OF CONTENTS DESCRIPTION COMMISSIONING INSTALLATION OPERATION SIZE COMPONENTS INSPECTION 6. SIZE COMPONENTS 45 Slips, Inserts, Guide Plates 46 7. DRAWINGS AND SPARE PARTS 47 754000-N-AIR FPS 500 for National RT 48 754000-N-AIR Parts list 49 752108 Slip Retainer Pin Assembly 50 752108 Parts list 50 754080 Feedback valve Assembly 51 754080 Parts list 51 754070 Locking Mechanism 52 754070 Parts List 52 553455 Bit Breaker Adapter Plate 53 754030-1 Cover Plate for Bit Breaker Plate 53 754030-2 Cover Plate for Cable Penetration 53 Guide Plates for Cable Penetration 54 Parts list Guide Plates for Cable Penetration 54 Upper Guard Guide Plates / Spider 55 Parts list Upper Guard Plates / Spider 55 Guide Plates Assembly / Elevator 56 Parts list Guide Plate Assembly / Elevator 56 Slip Assembly 57 Parts Lists Slip Assembly 57 754100-AIR Pneumatic Assembly 60 754100-AIR Parts List 61 DRAWINGS 8
DESCRIPTION DESCRIPTION 9
1. DESCRIPTION General DESCRIPTION The Blohm+Voss Flush Power Slip FPS 500 is designed to be installed into 37.5 rotary tables almost to flush level with the rig floor. It lowers the casing connection for easier operation and eliminates the need for work platforms. The FPS 500 is rated for 500 short tons. The FPS 500 is used for suspending tubular like casing, drill pipe, tubing and drill collars. Features Pneumatic operated flush mounted Power Slip Rapid changing of pipe sizes by means of Slip Assemblies. Material and manufacturing standard in acc. to API 7K Central Slip Grease System Pneumatic system is completely integrated and covered into the FPS 500 body. A pneumatic feedback signal is available, which shows that the Slip Assembly has been set. Intend of use FPS500 installed in the rotary table. The Power Slip is designed to be installed into 37.5 rotary tables almost to flush level with the rig floor and will be used for handling vertical pipe strings. Options Pneumatic connections The pneumatic connections are located on top of the FPS, above the drill floor. Rotary tables The tool is available for the following Rotary Tables: Rotary tables Configuration National Emsco Wirth Part number 754000-N-AIR 754000-E-AIR 754000-W-AIR Other rotary tables configurations on request. 10
Main assemblies 4 3 The power slips consist of the following main parts: 1. Body 2. Door 3. Slip Assembly 4. Top Cover incl. Guide Plates 5. Pneumatic Assembly DESCRIPTION 5 1 2 Improper / Unsafe Use The FPS 500 must only be used for the designated purpose. When using the FPS 500, the load of 500 sh tons must never be exceeded. Limited Warranty The warranty provided will be void if the Powerslip is either: a) repaired or serviced by a service facility which was not authorised by Blohm+Voss Oil Tools b) replacement parts not manufactured by Blohm+Voss Oil Tools are used c) modifications were made to the Powerslip which were not approved by Blohm+Voss Oil Tools Serial No. API License No. S W L 500 SH Tons P/N: 754000-... F PS 500 S/N:XXXXX Size 7K 0039 B+V 11/12 4.1/2" Safe working load Part No. Date of manufacturer Manufacturer Identification The identification area clearly identifies the Powerslip area (manufacturer, type, material, part number, serial number, date of manufacture). It is important to keep this information ready for the purpose of servicing and repair work. 11
DESCRIPTION Technical Data Rotary table: 37.5 Maximum allowable working load 500 sh tons Pipe size range (i.e. Drill pipe, casing, tubing and drill collar) 4.1/2 to 14 Weight Power Slip w/o Guide Plates and Slips Working pressure Maximum allowed pressure Recommended Flow rate Temperature working range ambient Pneumatic lines for operation Pneumatic line for feedback 2100 kg (4630 Lb) Min. 7 bar (100 Psi) up to 8,6 bar (125 Psi) 10 bar (145 Psi) 6,8 m3/min (1,8 Gpm) - 20 C to + 60 C - 4 F to 104 F A + B C 12
Options DESCRIPTION Standard cover plate Bit Breaker cover plate Cable penetration cover plate 13
31 Main Dimension DESCRIPTION 7,5 140 7,5 30 762 7,01 178 5,04 128 36,93 938 FPS500 for National 1014 39,92 45,42 1154 31 FPS500 for Wirth FPS500 for Emsco 948 37,32 39,92 1014 948 37,32 39,92 1014 14
Insert Carrier grip Length Drill Pipe and Casing DESCRIPTION 15
DESCRIPTION 16
COMMISSIONING COMMISIONING 17
2. COMMISSIONING Commissioning FPS 500 Blohm + Voss strongly recommends to accomplish the Flush Power Slip commissioning with the Blohm + Voss Commissioning Service. Read manual before first use! OK o Operating personnel is aware of all danger that depends on handling the B+V tool (see manual first)! COMMISIONING Prior to use of the Blohm+Voss Power Slip following checks must be carried out : Scope of supply OK o Cross check all delivered parts. Pneumatic Characteristics OK o OK o Operating pressure Min. 7 bar (100 psi) up to 10 bar (145 psi) Recommended flow rate 6,8 m3/min (1,8 Gpm) OK o Lubricator, air regulator and filter installed. Check and Lubrication OK o OK o Check for correct seating of Door Hinge Pins Apply grease to all greasing Points (see manual ) until grease is visibly coming out of the bores 18
INSTALLATION INSTALLATION 19
3. INSTALLATION Lifting and transport WARNING: Lift the Power Slip on the lifting ears only. WARNING: Wear your personal protection equipment at all times. Pneumatic System WARNING: Before start of work wear your personal protection equipment. Especially leak oil under pressure can cause severe personal injury to the eyes. Pneumatic connections INSTALLATION Purging air The FPS has three connection (A,B,C) on top. Conection A: Pneumatic Air pressure at connection "A" set the slips. Connection B: Pneumatic Air pressure at connection "B" raise the slips. Connection C: When the slips are completely set via connection "A", connection "C" applies a pneumatic pressure of approximately working pressure. Lines A,B and C connect the FPS to the Control Unit (optional equipment). The Control Unit has three ports (S1, S2, S3) that lead to the driller cabin. Two other ports (T, P) connect the Control Unit to the pneumatic ring or the pneumatic power unit. Lifting eyes C pneumatic connections B A Lifting Traverse 20
Schematic connection / control diagram DRILLER CABIN (supplied by others) S1 S2 S3 Tank line M 3/8" F P pneumatic pressure 3/8" F M T Control Unit (optional) A B C NOTE: - B + V does not supply electrical cable outside of the control unit and does not supply installation of electrical cable. - If FPS or Control Unit is delivered without Hook Up Kit, then B+V supplies complete couplings (both male and female) with outside thread for connection (see table for different thread sizes) M F 3/8" 3/8" F M 1/4" F M Pressure: Pneumatic pressure: 7-10 bar (100-145 psi) M 3/8" F 3/8" F M M 1/4" F INSTALLATION Legend A: Slips down B: Slips up C: Feedback signal T: Return line P: Pressure line T: Return S1: Signal to set the Slips S2: Signal to raise the Slips S3: Feedback Signal (when Slip properly set) Electric connection S1: 24V DC, (cable gland: cable diameter 4-9mm) S2: 24V DC, (cable gland: cable diameter 4-9mm) S3: max.250v, (cable gland: cable diameter 4-9mm) Connection Thread sizes A, B, P, T G 1/4" C G 1/4" Pneumatic line Electric line M: Male coupling F: Female Coupling 21
Checking Guide Plates Before installation, inspect the body guide plate, door guide and top guard guide plate on the power slip. Ensure that the used guide plates are properly secured and that the correct guide plate size is installed. Also ensure that the slips and inserts have the correct size. Body Guide Plate 6 5/8"- 7 " 6 5/8"- 7 " Size Door Guide Plate INSTALLATION Upper Guard Guide Plate / Half 6 5/8"- 7 " Size 22
1 2 Changing Slips Raise the slips, suspend them from a line and remove the cotter pin (1). Pull out the two retainer pin assemblies (2). Install the slip size desired, and then reinstall the retainer pin assemblies. Changing Slips 1 2 Changing Inserts Remove the retainer screws, washer and the insert retainer plates (1). Pull out the inserts and replace them with the required size (2). When reinstalling inserts, make sure the insert slots are greased and the inserts teeth are pointing upward. INSTALLATION Changing inserts 23
Installation FPS 500 Basically the FPS 500 has to be installed as shown in the manual Before installation into rotary table make sure, that the proper RT-Adapter is installed to the FPS 500. OK o OK o OK o OK o Make sure the required Guide Plates are installed before first use The Guide Plates are fixed with the screws Cover is closed Door is closed INSTALLATION Pneumatic Connections OK o OK o OK o OK o Function test FPS 500 is installed into Rotary Table Control Unit connected to Pneumatic Power Unit (PPU) FPS 500 connected to Control Unit All Pneumatic Lines are connected There are two possibilities to carry out the function test: 1. FPS 500 standing on the floor WARNING: Do not carry out the function test with the door opened 2. FPS 500 installed into the rotary table OK o Slip set OK o Feedback signal: Slips are Set OK o Slip raised 24
OPERATIONS OPERATIONS 25
4. OPERATIONS WARNING: Keep away from the FPS while operation. WARNING: Never raise the slips when the pipe load is still suspended by the slips. Safety 1. Make sure that ALL pneumatic lines are isolated before any work is carried out in the FPS. 2. It is recommended to have the FPS operated by the driller. 3. For smooth operation, it is recommended to slightly lower the pipe with the elevator while setting the FPS slips. 4. For smooth operation, it is recommended to slightly raise the pipe with the elevator while releasing the FPS slips. 5. The rotary locks in the outside of the FPS may only be needed on semisubmersible rigs or while floating in pipe when there is a chance the FPS could come out of the rotary table. Operation OPERATIONS 1. Check that slips are set on correct section of the pipe. Set the FPS before releasing the elevator. The slips are completely set, when the feedback signal is given. 2. When the rotary table and the FPS have to be rotated, always uncouple the quick disconnects on the FPS prior to rotation. 3. Place the FPS in the rotary table using all 4 lifting eyes and the lifting bracket. 4. Connect all pneumatic equipment and check for correct function of the tool. 5. With the pipe string being suspended by the FPS slips, make up or break the upper stand or joint, and handle it. 6. Pick up the weight of the pipe string with the elevator, before raising the FPS slips. 7. Set the slips of the FPS and then release the elevator. Removing the FPS when pipe is in the hole WARNING: Lift the FPS out of the rotary table ONLY with the 4 way lifting sling with the lifting bracket. Removing the FPS from drill pipe (in rotary) 1. Take the load from the slips 2. Raise the slips 3. Depressurize the FPS hook up hoses 4. Remove one hinge pin from the FPS door 5. Lift the FPS out of the rotary table by using the four way lifting bracket 6. Open the FPS door 7. Move the FPS away from the pipe / well center Connecting and disconnecting of the pneumatic hoses WARNING: Be careful when disconnecting pneumatic hoses. Make sure that there is no pressure on the hoses and the weight of the string cannot generate pressure Dis-connection hoses in slips up position 1. Set FPS in neutral position 2. Disconnect Quick Disconnects. 26
Handling the slip assembly during operation WARNING: The slip assembly should never be raised under load. WARNING: If the slip assembly is set the FPS can bear the load of the pipe. WARNING: Before raising the slip assembly, make sure that the elevator is closed and suspends the weight of the pipe. WARNING: Never operate the Slip Assembly with the door open. WARNING: Never set the Slips as long as the Elevator/Top Drive is still lifting or lowering the pipe. WARNING: With the power slip installed in the rotary there is the risk of small parts falling into the Power Slip or bore hole. WARNING: There is a risk of injury (danger of tripping) when the FPS top covers are open. OPERATIONS 27
(Emergency) opening the door Move Slip to upper position 1. Open the Cover by using the handle (1). 2. Remove the cotter pin (2) and pin (3). Cover 3. Pull out the hinge pin (4) by using a crane. 4. Open the Door. 5. To close the door again follow the same operation steps backwards. Handle (1) OPERATIONS (2) (4) (3) 28
MAINTENANCE & INSPECTION MAINTENANCE & INSPECTION 29
5. Maintenance and Inspection General If cracks, excessive wear etc. is recognised, contact Blohm + Voss Oil Tools or an authorised service company. Weldings of the castings should be done only by Blohm + Voss Oil Tools or an authorised service company in according to Blohm+Voss welding procedure. A regular preventative maintenance program should be established for all elevators. These written maintenance procedures should be given to the crew or maintenance personnel. Back of the Slips WARNING: For Service and Maintenance disconnect the pneumatic lines. Daily Lubrication When the tool is in use, the following lubrication procedure should be performed daily, or as inspection indicates: 1. Lubricate the bowl and back of the slips with heavy grease (See figure). 2. Lubricate the door hinge pins. 3. Grease the left and right yoke. (1) (1) (1) MAINTENANCE & INSPECTION 3 3 2 2 30
Grease daily All greasing points, which are labelled Grease Daily, must be greased at least once a day. It can be necessary to carry this out more often depending on use. Grease quality In order to achieve efficient greasing even at different environmental temperatures, we recommend the following grease types should be used (obtainable from Blohm + Voss Oil Tools): Low-Viscosity grease Type AVIATICON Grease XRF NLGI 0 Alternatively; use EP gear lubricating grease for greasing non-oil tight gear trains NESSOS SF0 NLGI 0 DIN 51 826 GPOF-25 DIN 51 502 GPOF-25 For higher ambient temperature up to 30 Celsius / 86 Fahrenheit we recommend to use NLGI 2 Recommended grease gun MAINTENANCE & INSPECTION 31
Inspection categories acc. to API RP 8B MAINTENANCE & INSPECTION Category I This category involves observing the equipment during operation for indications of inadequate performance. When in use, equipment shall be visually inspected on a daily basis for cracks, loose fits or connections, elongation of part, and other signs of wear, corrosion or overloading. Any parts found to show cracks, excessive wear, etc., shall be removed from service for further examination. The equipment shall be visually inspected by a person knowledgeable in that equipment and its function. Category II This is Category I inspection plus further inspection for corrosion, deformation, loose or missing components, deterioration, proper lubrication, visible external cracks, and adjustment. Category II may involve some disassembly to access specific components and to identify wear that exceeds the allowable tolerances. Category III This is Category II inspection plus further inspection, which should include NDT of critical areas and may involve some disassembly to access specific components and to identify wear that exceeds the allowable tolerances. Prior to inspection, all foreign material such as dirt, paint, grease, oil, scale, etc. shall be removed from the concerned parts by a suitable method (e.g. paint-stripping, steam-cleaning, grit-blasting). Category IV This is Category III inspection plus further inspection for which the equipment is disassembled to the extent necessary to conduct NDT of all primary-load-carrying components. Equipment shall be: disassembled in a suitableequipped facility to the extent necessary to permit full inspection of all primary-loadcarrying components and other components that are critical to the equipment. inspected for excessive wear, cracks, flaws and deformation. Procedure: Corrections shall be made in accordance with the manufacturer s recommendations. Prior to inspection, all foreign material such as dirt, paint, grease, oil, scale, etc. shall be removed from the concerned parts by a suitable method (e.g. paintstripping, steam-cleaning, gritblasting) Frequency Periodic inspection The recommended schedule for inspection of all kind of Power Slips: Ongoin: I Weekly: II 6 Monthly: III 1 Year: IV The recommended frequencies apply for equipment in use during the specified period. The inspection frequencies are only recommendations. The schedule of inspection heavily depends on the following factors: environment load cycles regulatory requirements operating time testing repairs re manufacture Non-periodic inspection A complete, on-job, shut-down inspection equivalent to the periodical Category III or Category IV should be made before (if anticipated) and after critical jobs (e.g., running heavy casing / drill strings, jarring, pulling on stuck pipes and/or operating at extreme low temperatures) <-20 C (<-4 F). Inspection A thorough inspection should be carried out periodically (every 3 months) or as special circumstances may require. Before starting an inspection disconnect any hydraulic/pneumatic system and remove all foreign materials (dirt, paint, grease Oil, scale, etc.) from surface by a suitable method. After a field inspection, it is advisable to record the extent of testing and testing results. Conduct the periodic or critical load inspection in the field by the crew with the supervisor. If cracks, excessive wear etc. is recognized, contact Blohm + Voss Oil Tools or an authorized service company. Inspection of Hydraulic/ Pneumatic System Check for leakage every day. Should internal or external leakage reach an unacceptable high level, contact Blohm + Voss Oil Tools or an authorized service company. Critical Load Inspection Critical loads may occur. For example: impact loads such as jarring, pulling on stuck pipe, etc. If critical loads occurred unexpectedly, conduct the inspection immediately. 32
Dismantling Inspection Generally, when the equipment returns to base, warehouse, etc. Carry out the Tool inspection, immediately. Furthermore, control it prior to its being sent on the next job. The Tool should be dismantled and inspected in a suitably equipped facility for excessive wear, cracks, flaws or deformations. Corrections should be made in accordance with recommendations which can be obtained from Blohm + Voss Oil Tools. Weldings at the castings should be done only by Blohm + Voss Oil Tools or an authorized service company in according to Blohm+Voss welding procedure. When need is shown in a field inspection, dismantle the Tool and arrange an inspection in a suitably equipped facility. Springs should be carefully visually inspected for excessive wear and obvious weakness. MAINTENANCE & INSPECTION 33
Inspection check lists CHECK LIST FRONT PAGE TYPE OF EQUIPMENT SERIAL NUMBER PART NUMBER SUPERVISOR DATE OF INSPECTION INSPECTION CATEGORY PLACE OF INSPECTION MAINTENANCE & INSPECTION 34
Check List Category I (During operation - Flush Power Slip is placed in the Rotary Table, Cover is closed) GENERAL DESCRIPTION CHECKED SIGNATURE 1 Complete front page of check list for the records OK 2 Check for correct size of slips and guide plates OK 3 Check correct function of Slips OK 4 Check function of feedback signal (slips set / raised) OK Remarks CHECK FOR LOOSE ITEMS, ESPECIALLY FOR: DESCRIPTION CHECKED SIGNATURE 1 Hinges and bolts of cover assembly OK 2 Cover Locking device OK 3 Fixation of guide plates OK 4 Top cover screws OK 5 Lifting eyes for Power Slip OK Remarks CHECK FOR CRACKS, ELONGATION, DAMAGE AND CORROSION, ESPECIALLY FOR: DESCRIPTION CHECKED SIGNATURE 1 Power Slip Body Hinges of Cover Assembly OK 2 Hinges and bolts of cover assembly OK 3 Cover Locking device OK 4 Guide plates OK 5 Lifting eyes for Power Slip OK Remarks MAINTENANCE & INSPECTION 35
CHECK FOR WEAR, ESPECIALLY FOR: DESCRIPTION CHECKED SIGNATURE Pneumatic guide plates: Check wear at inside surface 1 Replace the guide if wear is more than 10 mm at the bevel inside the guide plate. OK Remarks HYDRAULIC DESCRIPTION CHECKED SIGNATURE 1 Check for loose fittings, pipes, valves OK 2 Check for pneumatic leaks (hoses, valves and cylinders) OK 3 Check condition of pneumatic couplings and connection hoses OK Remarks MAINTENANCE & INSPECTION SUPERVISOR DATE 36
Check List Category II (Flush Power Slip is out of Rotary Table, Cover is open) GENERAL DESCRIPTION CHECKED SIGNATURE 1 Complete front page of check list for the records OK 2 Check for correct size of slips and guide plates OK 3 Check correct function of Slips: Set Slips cycle: 1. Set Slips OK 2. Raise Slips 4 Check function of feedback signals (slips set / raised) OK Remarks CHECK FOR LOOSE ITEMS, ESPECIALLY FOR: DESCRIPTION CHECKED SIGNATURE 1 Hinges and bolts of cover assembly OK 2 Cover Locking device OK 3 Fixation of guide plates OK 4 Top cover screws OK 5 Lifting eyes for Flush Power Slip OK 6 Transportation beam OK 7 Fixation of Pneumatic Cylinder OK 8 Fixation of Pneumatic Hoses below Cover Assembly OK Remarks CHECK FOR CRACKS, ELONGATION, DAMAGE AND CORROSION, ESPECIALLY FOR: DESCRIPTION CHECKED SIGNATURE 1 Flush Power Slip Body Hinges of Pneumatic Cylinder OK 2 Flush Power Slip Body Hinges of Cover Assembly OK 3 Flush Power Slip Body Outside Body surface / contact areas to rotary table OK 4 Hinges and bolts of cover assembly OK 5 Cover Locking device OK 6 Guide plates OK 7 Lifting eyes for Flush Power Slip OK 8 Transportation beam OK 9 Check condition of Insert Retainer Plates and Screws OK 10 Check teeth of insert dies OK 11 Check load recess at bottom OK 12 Slip Assembly Hinges for Pneumatic Cylinder OK 13 Slip Assembly Hinges and bolts between Center/Left/Right-segments OK Remarks MAINTENANCE & INSPECTION 37
CHECK FOR WEAR, ESPECIALLY FOR: DESCRIPTION Pneumatic guide plates: Check wear at inside surface Replace the guide if wear is more than 10 mm at the bevel inside the guide 1 plate CHECKED SIGNATURE OK 2 Check wear of insert dies OK Remarks GREASING DESCRIPTION CHECKED SIGNATURE 1 Check that grease system and grease points get grease to all needed areas (as far as observable) especially for: OK 2 Slip Assembly back side OK 3 Cover Assembly Locking Device OK 4 Feedback signal OK 5 Hinges at Door and Body OK Remarks HYDRAULIC DESCRIPTION CHECKED SIGNATURE 1 Check for loose fittings, pipes, valves OK 2 Check for pneumatic leaks of all hoses, valves and cylinders OK 3 Check condition of pneumatic couplings and connection hoses OK 4 Check pneumatic fittings and hoses in rotary table OK Remarks MAINTENANCE & INSPECTION REMARKS SUPERVISOR DATE 38
Check List Category III (Flush Power Slip is out of Rotary Table, Cover is open, Slip Assembly disassembled) USE CHECK LIST OF CATEGORY II WITH FOLLOWING ADDITIONAL ITEMS: DESCRIPTION CHECKED SIGNATURE GENERAL 1 Check completeness and condition of warning plates and labels OK 2 Check condition of identification plate (serial number, part number, date of manufacture etc.) OK 3 Clean tool thoroughly OK NDT - INSPECTION NDT all critical areas with die penetrant OK REMARKS MAINTENANCE & INSPECTION SUPERVISOR DATE 39
Check List Category IV (Flush Power Slip is out of Rotary Table, Cover is open, Slip Assembly disassembled) USE CHECK LIST OF CATEGORY III WITH FOLLOWING ADDITIONAL ITEMS: HYDRAULICS CHECKED SIGNATURE 1 Change all pneumatic hoses and fittings OK 2 Check condition of pneumatic valves and replace if necessary OK 3 Check condition of pneumatic pipes and replace if necessary OK REMARKS MAINTENANCE & INSPECTION SUPERVISOR DATE 40
Wear data criteria Bore of Door and Body Hinges FPS 500 Dimension worn max: Dimension new max: Door Hinge Pin Hinge pin min dia new: Hinge pin min dia worn min: Dim. A 81,120 mm 80,106 mm 79,80 mm 79,80 mm Dim. A Door/Body Hinge dimensions MAINTENANCE & INSPECTION Door/body hinge 41
Critical Areas Critical Areas Body Critical Areas Door and Hinge Pin Critical Areas Slips MAINTENANCE & INSPECTION 42
Critical area drawings of lifting eyes MAINTENANCE & INSPECTION 43
Handling, storage and transport Storage Storage of the tool requires the following measures to be taken: Ensure the tool is protected from water ingress Ensure the tool is stored in such a way, that personnel cannot be wounded by moving parts or sharp edges. If needed, secure the tool with ropes or otherwise in order to protect it from sliding due to ship movements. Short term storage after use and less then 3 months Preserve the tool: Grease all blank surfaces with grease: Cylinders Preserve all other blank surfaces with Tectyl Type 864 or equivalent Storage: Store in a dry environment with humidity max 80%. Commissioning: Not needed Long term storage over 3 months MAINTENANCE & INSPECTION Preserve the tool: Grease all blank surfaces with grease: Cylinders Preserve all other blank surfaces with Tectyl Type 864 or equivalent Storage: Store in a dry environment with humidity max 80% Commissioning: As per procedure in the User Manual Handling Lift the tool by its lifting ears only. Transport When the tool is in it s original crate, use a fork lift for lifting the crate only. The weight of the tool is indicated on the identification area of the tool, and also on its original transporting crate. 44
SIZE COMPONENTS SIZE COMPONENTS 45
6. SIZE COMPONENTS Slips, Inserts, Guide Plates API Slip Assemblies Inserts Elevator Guide Plates Spider Guide Plates Size Pipe Size P/N P/N-Qty 5.1/2 Guide P/N 4.1/2 752510 350905-45 752390 5 752500 350506-45 5.1/2 752490 350107-45 Screw P/N Washer P/N Guide P/N 752710 Screw P/N Washer P/N Diameter ø 145 752935 752715 ø 165 7.5/8 9.5/8 10.3/4 11.3/4 14 6.5/8 752480 350909-75 7 752470 350610-75 752940 752720 ø 205 7.5/8 752460 350111-75 7.3/4 752465 350011-75 752945 752725 ø 225 8.8/5 752450 350911-90 752965 752730 ø 250 9.5/8 752440 350111-90 752308 752309 752333 752325 9.5/8 752360 351011-90 752970 752735 ø 280 9.7/8 752370 350811-90 10.3/4 752350 350111-90 752975 10.3/4 752430 350912-105 752740 ø 305 11.3/4 752420 350112-105 752980 11.7/8 752425 350012-105 752745 ø 330 12.3/4 752375 350112-135 752985-2 752755 ø 355 13.3/8 752380 350612-135 752990-2 13.5/8 752385 350413-135 752760 ø 375 14 752390 350113-125 752995-2 752770 ø 385 SIZE COMPONENTS 46
DRAWINGS & SPARE PARTS 47 DRAWINGS & SPARE PARTS
7. DRAWINGS AND SPARE PARTS 754000-N-AIR FPS 500 for National RT 14 28 44 16 33 51 25 24 41 5 57 17 58 59 60 43 41 49 3 4 54 27 54 8 12 7 43 37 42 20 21 13 40 21 50 35 41 15 29 47 26 41 10 43 87997 Feedback valve 6 51 23 43 36 48 30 32 11 22 45 9 18 34 57 58 46 38 52 55 39 53 1 DRAWINGS & SPARE PARTS 2 56 31 48
754000-N-AIR Parts list Pos. Qty. Part No. Description Pos. Qty. Part No. Description 1 1 754005-BF Body 48 2 613783 Safety Sheet 2 1 754006-BF Door 49 2 621435 Washer 3 1 754011 Yoke, left 50 4 612679 Washer 4 1 754012 Yoke, right 51 24 792106 Washer 5 2 754050 Hinge Pin 52 2 792104 Washer 6 2 754053-1 Cylinder Mounting 53 2 792113 Washer 7 2 754095-1 Cylinder Flange 54 2 611524 Warning Sign Don t touch 8 2 754051 Cylinder Pin 55 1 613129 Technical Support 9 2 754055 Locking Device 56 1 671638 Warning Sign Blohm + Voss 10 2 754070 Locking Mechanismus 57 2 671640 Warning Sign Hands 11 2 754099 Clevis Pin with Head 58 2 671641 Warning Sign Squeeze Danger 12 2 754057 Yoke Pivot Pin 59 3 671642 Warning Sign Grease Daily 13 2 754058 Cylinder Pin 60 3 671644 Lubrication Warning 14 2 752108 Slip Retainer Pin Assembly 15 1 752206-1 Slip Stop Pin 16 1 754060 Cover National 17 1 754030 Cover Plate 18 1 754080 Feedback valve Assembly 19 1 754100-AIR Pneumatic Assembly 20 1 754101-2 Contributor Block 21 2 754102 Pneumatic Cylinder 22 1 754081 Feedback Cover 23 2 754001 Adapter National 24 1 Table Sheet 61 Slip Assembly 25 1 752725 Spider Plate Assembly 26 2 754097 Hose Protection 27 2 754091 Bushing 28 4 553468 Lifting Eye 29 4 725135 Screw 30 2 752129 Screw 31 2 792041 Screw 32 4 755312 Screw 33 16 648109 Screw 34 2 613548 Screw 35 8 755167 Hexagon Screw 36 2 645649 Screw 37 2 675058 Cylinder Screw 38 12 754098 Sealing Screw 39 3 771108 Blind Screw 40 2 752137-2 Nut 41 6 70064 Grease Fitting 42 1 756790 Grease Fitting 43 8 753058 Cotter Pin 44 2 752314 Cotter Pin 45 6 775048-1.5 Grease Nozzle 46 6 775048-2.0 Grease Nozzle 47 4 613783 Safety Sheet DRAWINGS & SPARE PARTS 49
752108 Slip Retainer Pin Assembly 4 1 2 3 752108 Parts list Pos. Qty Part. No. Description 1 1 752209 Retainer Pin 2 1 752210 Roller 3 1 641011 Retainer Ring 4 1 70064 Grease Nipple DRAWINGS & SPARE PARTS 50
754080 Feedback valve Assembly A Slips raised SCHNITT A-A Slips set 1 6 105 113 7 5 8 754080 Parts list Pos. Qty. Part no. Description 1 1 754085 Mounting Plate 2 1 754084 Feedback sleeve 3 1 754086 Feedback Pin 1 4 1 754089 Feedback Pin 2 5 1 752219 Overload Spring 6 1 612671 Screw 7 1 755251 Nut 8 1 755248 Washer DRAWINGS & SPARE PARTS 40 2 4 3 A acivtated by yoke 95 51
754070 Locking Mechanism 3 1 2 754070 Parts list Pos. Qty Part. No. Description 1 1 754071 Locking Pin 2 1 754072 Handle 3 1 70064 Grease Fitting DRAWINGS & SPARE PARTS 52
553455 Bit Breaker Adapter Plate 754030-1 Cover Plate for Bit Breaker Plate 754030-2 Cover Plate for Cable Penetration DRAWINGS & SPARE PARTS 53
Guide Plates for Cable Penetration Parts list Guide Plate Assembly for Cable Penetration Part-No. Pipe Size Weight (Kg) 754033 4.1/2 35,5 754034 5-5.1/2 34,8 754035 6.5/8-7 30,4 754036 7.5/8-7.3/4 36,10 754037 8.5/8 754038 9.5/8-9.7/8 25,7 754039 10.3/4 23,7 754040 11.3/4-11.7/8 21,4 754041 12.3/4 22,3 754042 13.3/8-13.5/8 19,7 754043 14 16,4 DRAWINGS & SPARE PARTS 54
Upper Guard Guide Plates / Spider Parts list Upper Guard Plates / Spider Part no. Pipe Size 752710 4.1/2 752715 5-5.1/2 752720 6.5/8-7 752725 7.5/8-7.3/4 752730 8.5/8 752735 9.5/8-9.7/8 752740 10.3/4 752745 11.3/4-11.7/8 752755 12.3/4 752760 13.3/8-13.5/8 752770 14 DRAWINGS & SPARE PARTS 55
Guide Plates Assembly / Elevator (Body Guide Plate and Door Guide Plate) Body Guide Plate 6 5/8"- 7 " 6 5/8"- 7 " Size Door Guide Plate Parts list Guide Plates Assembly / Elevator Part no. Description Pipe size PN Body Plate PN Door Plate 752930 Guide Plate Ass. 4.1/2 752930-1 752930-2 752935 Guide Plate Ass. 5-5.1/2 752935-1 752935-2 752940 Guide Plate Ass. 6.5/8-7 752940-1 752940-2 752945 Guide Plate Ass. 7.5/8-7.3/4 752945-1 752945-2 752965 Guide Plate Ass. 8.5/8 752965-1 752965-2 752970 Guide Plate Ass. 9.5/8-9.7/8 752970-1 752970-2 752975 Door Guide Plate 10.3/4 752975-1 752975-2 752980 Door Guide Plate 11.3/4-11.7/8 752980-1 752980-2 752985-2 Door Guide Plate 12.3/4 ----- 752985-2 752990-2 Door Guide Plate 13.3/8 ----- 752990-2 752995-2 Door Guide Plate 14 ----- 752995-2 DRAWINGS & SPARE PARTS 56
Slip Assembly 2 7 8 9 10 3 4 1 6 5 Parts List Slip Assembly Pos. Qty Part no. Part no. Part no. Description 5.1/2 x4.1/2 PN. 752510 5.1/2 x5 PN. 752500 5.1/2 x5.1/2 PN. 752490 1 1 752491 752491 752491 Center Slip Segment 5.1/2 2 1 752492 752492 752492 Left Slip Segment 5.1/2 3 1 752493 752493 752493 Right Slip Segment 5.1/2 4 2 752221-1 752221-1 752221-1 Hinge Pin 5 2 752404 752404 752404 Hinge Pin Cotter 6 2 752405 752405 752405 Spring 7 45 350905 350506 350107 Inserts Updated 8 3 752496 752496 752496 Insert Retainer 9 6 752324 752324 752324 Cap Screw 10 6 752325 752325 752325 Lock Washer DRAWINGS & SPARE PARTS 57
Pos. Qty Part no. Part no. Part no. Part no. Description 7.5/8 x6.5/8 PN. 752480 7.5/8 x7 PN. 752470 7.5/8 x7.3/4 PN. 752465 7.5/8 x7.5/8 PN. 752460 1 1 752461 752461 752461 752461 Center Slip Segment 7.5/8 2 1 752462 752462 752462 752462 Left Slip Segment 7.5/8 3 1 752463 752463 752463 752463 Right Slip Segment 7.5/8 4 2 752221-1 752221-1 752221-1 752221-1 Hinge Pin 5 2 752404 752404 752404 752404 Hinge Pin Cotter 6 2 752405 752405 752405 752405 Spring 7 75 350909 350610 350011 350111 Inserts Upgrated 8 3 752466 752466 752466 752466 Insert Retainer 9 6 752324 752324 752324 752324 Cap Screw 10 6 752325 752325 752325 752325 Lock Washer Pos. Qty Part no. Part no. Description 9.5/8 x8.5/8 PN. 752450 9.5/8 x9.5/8 PN. 752440 1 1 752441 752441 Center Slip Segment 9.5/8 2 1 752442 752442 Left Slip Segment 9.5/8 3 1 752443 752443 Right Slip Segment 9.5/8 4 2 752221-1 752221-1 Hinge Pin 5 2 752404 752404 Hinge Pin Cotter 6 2 752405 752405 Spring 7 90 350911 350111 Inserts Upgrated 8 3 752446 752446 Insert Retainer 9 9 752324 752324 Cap Screw 10 9 752325 752325 Lock Washer Pos. Qty Part no. Part no. Part no. Description 10./4 x9.7/8 PN. 752370 10.3/4 x9.5/8 PN. 752360 10.3/4 x10.3/4 PN. 752350 1 1 752351 752351 752351 Center Slip Segment 9.5/8 2 1 752352 752352 752352 Left Slip Segment 9.5/8 3 1 752353 752353 752353 Right Slip Segment 9.5/8 4 2 752221-1 752221-1 752221-1 Hinge Pin 5 2 752404 752404 752404 Hinge Pin Cotter 6 2 752405 752405 752405 Spring 7 90 350811 351011 350111 Inserts Upgrated 8 3 752354 752354 752354 Insert Retainer 9 9 752324 752324 752324 Cap Screw 10 9 752325 752325 752325 Lock Washer DRAWINGS & SPARE PARTS 58
Pos. Qty Part no. Part no. Part no. Description 11.3/4 x10.3/4 PN. 752430 11.3/4 x11.7/8 PN. 752425 11.3/4 x11.3/4 PN. 752420 1 1 752421 752421 752421 Center Slip Segment 11.3/4 2 1 752422 752422 752422 Left Slip Segment 11.3/4 3 1 752423 752423 752423 Right Slip Segment 11.3/4 4 2 752221-1 752221-1 752221-1 Hinge Pin 5 2 752404 752404 752404 Hinge Pin Cotter 6 2 752405 752405 752405 Spring 7 105 350912 350012 350112 Inserts Upgrated 8 3 752426 752426 752426 Insert Retainer 9 9 752324 752324 752324 Cap Screw 10 9 752325 752325 752325 Lock Washer Pos. Qty Part no. Part no. Description 13.3/8 x12.3/4 PN. 752410 13.3/8 x13.3/8 PN. 752400 1 1 752401 752401 Center Slip Segment 13.3/8 2 1 752402 752402 Left Slip Segment 13.3/8 3 1 752403 752403 Right Slip Segment 13.3/8 4 2 752221-1 752221-1 Hinge Pin 5 2 752404 752404 Hinge Pin Cotter 6 2 752405 752405 Spring 7 135 350612 350112 Inserts Upgrated 8 3 752406 752406 Insert Retainer 9 12 752324 752324 Cap Screw 10 12 752325 752325 Lock Washer Pos. Qty Part no. Part no. Part no. Part no. Description 14 x14 PN. 752390 14 x13.5/8 PN. 752385 14 x13.3/8 PN. 752380 14 x12.3/4 PN. 752375 1 1 752391 752391 752391 752391 Center Slip Segment 14 2 1 752392 752392 752392 752392 Left Slip Segment 14 3 1 752393 752393 752393 752393 Right Slip Segment 14 4 2 752221-1 752221-1 752221-1 752221-1 Hinge Pin 5 2 752404 752404 752404 752404 Hinge Pin Cotter 6 2 752405 752405 752405 752405 Spring 7 135 350113 350413 350612 350112 Inserts Upgrated 8 3 752407 752407 752407 752407 Insert Retainer 9 12 752408 752408 752408 752408 Cap Screw 10 12 725102 725102 725102 725102 Lock Washer DRAWINGS & SPARE PARTS 59
754100-AIR Pneumatic Assembly Cylinder PN 754102 Cylinder PN 754102 5 6 7 6 5 8 FPS 500 8 4.1 10 11 2 2 9 9 X X 5 5 4.4 4.5 9 1 4.3 1 9 1 2 2 1 4.6 6 9 9 10 11 4.2 9 10 6 4.7 3 10 4.8 Pneumatic Block PN 754101-2 A1 C1 B1 C 12 4.11 13 14 A B 12 12 4.9 4.10 13 14 13 14 DRAWINGS & SPARE PARTS 60
754100-AIR Parts List Pos. Quantity Part no. Description 1 2 710601 Throttle 2 2 754103 Back pressure valve 3 1 87997 Directional control valve 4 1 754100-AIR-40 Hydraulic Hose Assembly for FPS 500-AIR 4.1 1 613176 Pneumatic Hose 4.2 1 613176 Pneumatic Hose 4.3 1 613176 Pneumatic Hose 4.4 1 613176 Pneumatic Hose 4.5 1 613176 Pneumatic Hose 4.6 1 613176 Pneumatic Hose 4.7 1 613176 Pneumatic Hose 4.8 1 613176 Pneumatic Hose 4.9 1 754100-AIR-A Hose Assembly A 4.10 1 754100-AIR-B Hose Assembly B 4.11 1 754100-AIR-C Hose Assembly C 5 4 612908 Reducing nipple 6 4 612909 T-Connector 7 1 613150 T-Connector 8 2 754104 L-Connection 9 7 613146 Straight fitting 10 4 613148 Elbow Fitting 11 2 671590-2 Connector socket 12 3 613945 Fitting 13 3 612899-2 Coupling 14 3 612892 Clutch hose coupling DRAWINGS & SPARE PARTS 61