CS/ SERIES CLUTCH SHIFT PTO PARTS LIST AND SERVICE MANUAL Muncie Power Products, Inc.
CS/ PTO EXPLODED VIEWS Detail B Detail A Detail E Detail C Detail D DETAIL A OUTPUT SHAFT ASSEMBLY 7 CS/ STANDARD OUTPUT SHAFT ASSEMBLY 9 6 6 Detail AA 0 7 0 DETAIL AA - STANDARD CLUTCH PACK - DISC LOCATIONS* *The standard clutch pack assembly contains a pair of stator plates stacked between each friction disc. The assembly should begin and end with a friction disc. 7 CS/ I, D & Z OUTPUT SHAFT ASSEMBLY 9c 0 7 6 9a 9b Detail AB 9d 6 Muncie Power Products, Inc.
CS/ PTO EXPLODED VIEWS DETAIL AB - I, D & Z CLUTCH PACK DISC LOCATIONS** 0 9a 9c 9b 0 9d ** The I, D & Z clutch pack assembly contains a single stator plate stacked between each friction disc. The assembly should begin and end with a friction disc. Note: The output shaft for the I, D & Z output option is a larger diameter shaft and requires different clutch pack components. The -piece clutch hub is assembled by inserting the clutch hub (9d) into the flange (9c). These items are held together with a snap ring (9b) and the spacer (9a) is placed on the output shaft () BEFORE installing the clutch hub assembly. 9 DETAIL B END COVER ASSEMBLY CS COVER ASSEMBLY DIRECT SOLENOID 6 - Ft.Lb. 7 9 CS COVER ASSEMBLY REMOTE SOLENOID Ft.Lb. 0 0 Ft.Lb. 6 Ft.Lb. 6 0 6 Ft.Lb. DETAIL C INPUT SHAFT ASSEMBLY CS/ INPUT SHAFT 0 Ft.Lb. 9 7 6 Ft.Lb. DETAIL D PTO HOUSING ASSEMBLY CS/ HOUSING 0 6 0 7 Muncie Power Products, Inc. 7
CS/ PTO EXPLODED VIEWS DETAIL E OUTPUT OPTIONS STANDARD HYDRAULIC OUTPUT K, P & Z SHOWN 9 0 Ft.Lb. B OUTPUT OPTION 9 0 Ft.Lb. DETAIL E - C & OUTPUT OPTION 9 0 Ft.Lb. Ft.Lb. DETAIL E - I, D & Z OUTPUT OPTION a 9 0 Ft.Lb. Muncie Power Products, Inc.
PARTS LIST & DESCRIPTION ITEM QTY PART NO. DESCRIPTION 0 T6 Washer (CS, CS6) 0 T6 Plate (CS, CS6) 0 T70 Snap Ring 0 T0 Snap Ring 0 T907 Thrust Washer 06 See Table A* Bell Gear 07 0T6 Needle Roller Bearing 0 See Table B* Output Shaft 09 0T79 Clutch Hub 09a T907 Washer ( I, D & Z ) 09b T79 Snap Ring ( I, D & Z ) 09c 9T Flange ( I, D & Z ) 09d 9T9 Clutch Hub ( I, D & Z ) 0 9T6 Friction Disc 9T Friction Disc (CS6 Only) 9T06 Spacer Disc 9T0 Spacer Disc (CS6 Only) 9T06 Spacer Disc ( I, D & Z ) 7T6 Spring T67 O-Ring T60 O-Ring ( I, D & Z ) 9T66 Piston 9T Piston ( I, D & Z ) T67 O-Ring 6 9T66 Piston Cup 9T Piston Cup ( I, D & Z ) 7 T670 Snap Ring T600 Snap Ring ( I, D & Z ) T7 Cap Plug ( G, K, Q & S ) T7 Cap Plug ( P ) T7767 Cap Plug ( I & D ) T96 Cap Plug ( Z ) T77 Cap Plug ( T ) 9 9T9 Protector 0 9T67 Setscrew 7T67 Spring T6 Pipe Plug 9T6 Capscrew T6 Plug T6 Tee 6 T060 Solenoid V T06 Solenoid V 7 9T09 mm Capscrew T06 Bearing Cover, Closed (CS) (w/ Drop in Solenoid) T07 Bearing Cover, Closed (CS) (w/o Drop in Solenoid) 9 T697 O-Ring 0 T60 O-Ring 0T07 Bearing 0T07 Bearing ( I, D & Z ) a 0T Bearing ( I, D & Z ) 6T67 Roll Pin (CS, CS6) T67 Plate (CS, CS6) See Table C* Bearing Shim 0T776 Tapered Roller Bearing (sold w/input gear only) 6 07T70 Idler Shaft 7 See Table D* Cone Spacer See Table E* Input Gear 9 T Bearing Shim (.060"/.0600") 0 9T7 Set Screw ITEM QTY PART NO. DESCRIPTION T777 Gasket See Table F* PTO Housing T7 Orifice T999 Plug T67 Elbow 6 T60 Hose 7 T77 O-Ring T67 Spacer ( B, C, G, K, P, Q, S, T & 6 ) T90 Spacer ( D, I, Z ) 9 T67 O-Ring T O-Ring ( I, D & Z ) 0 See Table G* Flange/Seal Assembly 9T76 Capscrew ( B, C & ) 9T6 Socket Capscrew ( K & P Hyd.) 9T97 Socket Capscrew ( G, Q & S Hyd) 9M7 Socket Capscrew ( I & D ) 9T9 Socket Capscrew ( Z ) 9T66 Capscrew ( C, X & ) 9T9 Capscrew ( V ) 6T067 Woodruff Key T77 Companion Flange T77 C Companion Flange T009 Flat Washer ( C, X & ) N.S. TK0 Installation Kit (V) Includes: Shift Kit, Gasket Pack, Stud Kit & Std. Hose Kit N.S. TK0 Installation Kit (V) Includes: Shift Kit, Gasket Pack, Stud Kit & Std. Hose Kit N.S. TK Installation Kit (V) Includes: Shift Kit, Gasket Pack, Stud Kit & Special Hose Kit (7") N.S. TK70 Installation Kit (/V) P Option Includes: Shift Kit, Gasket Pack, Stud Kit, Std. Hose Kit, Pressure Switch & Pressure Switch Fittings N.S. CS-GSK Gasket Kit Includes: (), (), ()9, ()0, (), ()7, ()9, ()T7790 & ()TK90 N.S. CS-GSK-IZ Gasket Kit Includes: (), (), ()9, ()0, (), ()7, ()9, ()T779 & ()TK90 N.S. CS-RBK Rebuild Kit Includes: (), (), (),(), ()0, (), (), (), (), ()7, (), ()9, ()0, (), (), ()9, (),()7 ()9, ()T7790 & ()TK90 N.S. CS-RBK-IZ Rebuild Kit Includes: (), (), (), (), ()0, (), (), (), (), ()7, (), ()9, ()0, (), ()a, (), (), ()7, ()9, ()T779 & ()TK90 N.S. CS6-RBK Rebuild Kit Includes: (), (), (), (), ()0, (), (), (), (), ()7, (), ()9, ()0, (), (), (), ()7, ()9, ()T7790 & ()TK90 N.S. TK0 Conversion Kit to CS V N.S. TK0 Conversion Kit to CS V * Tables A, B, C, D, E, F, & G are located on page 6. Muncie Power Products, Inc.
TABLES A, B, C, D, E, F & G Table A Bell Gear (Item 6) PART NO DESCRIPTION 0T99 Bell Gear 0 ( T) 0T666 Bell Gear 06 (6 T) 0T667 Bell Gear 07 ( T) 0T66 Bell Gear 0 ( T) 0T669 Bell Gear 0 (0 T) 0T7 Bell Gear ( T) 0T6 Bell Gear (7 T) 0T Bell Gear ( T) Table B Output Shaft (Item ) PART NO DESCRIPTION 06T6 Output Shaft B ¼" Rd. 06T77 Output Shaft C or." SPL 06T90 Output Shaft D Euro DIN6 06T69 Output Shaft G DANA SPECIAL 06T07 Output Shaft I DIN6 06T67 Output Shaft K 7 SPL, & 6 06T60 Output Shaft P " SPL 06T6 Output Shaft Q & S 7 SPL 06T77 Output Shaft T ¾" T SPL Output Shaft V and Z Extended 06T7 Shaft Type Table C Input Bearing Shim (Item ) PART NO DESCRIPTION DIMENSION T7 Bearing Shim (.0"/.0") T Bearing Shim (.7"/.") T9 Bearing Shim (.00"/.0") T0 Bearing Shim (."/.0") T Bearing Shim (.0"/.0") T Bearing Shim (.7"/.") T Bearing Shim (.00"/.0") T Bearing Shim (."/.0") T Bearing Shim (.0"/.0") T6 Bearing Shim (.7"/.") T7 Bearing Shim (.00"/.0") T Bearing Shim (."/.0") T9 Bearing Shim (.0"/.0") T0 Bearing Shim (.7"/.") T Bearing Shim (.00"/.0") TK Bearing Shim Kit Includes all bearings Table D Cone Spacer (Item 7) PART NO DESCRIPTION DIMENSION T7 Cone Spacer (0.7"/0.7") T Cone Spacer (0.70"/0.7") T Cone Spacer (0.77"/0.7") T Cone Spacer (0.7"/0.7") T Cone Spacer (0.7"/0.79") T6 Cone Spacer (0.7"/0.76") T7 Cone Spacer (0.7"/0.7") T Cone Spacer (0.7"/0.70") T9 Cone Spacer (0.79"/0.77") T0 Cone Spacer (0.76"/0.7") T90 Cone Spacer (0.7"/0.7") T9 Cone Spacer (0.70"/0.70") T9 Cone Spacer (0.707"/0.70") The cone spacer installs between the tapered input bearings to set the bearing preload at.00" -.006" loose. Critical dimension. See page /0 for visual detail. Purchase input gear assembly (Item 0TAXXXX) which includes the correct cone spacer. Table E Input Gear (Item ) ASSY NO DESCRIPTION BASE GEAR 0TA6 A00 Input Gear (0T/T) 0T7 0TA6 A006 Input Gear (0T/T) 0T99 0TA66 A007 Input Gear (0T/T) 0T7 0TA67 A00 Input Gear (0T/7T) 0T7 0TA6 A00 Input Gear (0T/9T) 0T76 0TA7 A0 Input Gear (0T/T) 0T6 0TA69 A0 Input Gear (0T/T) 0T6 0TA60 A0 Input Gear (0T/T) 0T0 0TA97 C90 Input Gear (T/T) 0T07 0TA979 C906 Input Gear (T/T) 0T07 0TA90 C907 Input Gear (T/T) 0T0 0TA9 C90 Input Gear (T/7T) 0T09 0TA9 C90 Input Gear (T/9T) 0T00 0TA9 C9 Input Gear (T/T) 0T0 0TA9 C9 Input Gear (T/T) 0T0 Table F PTO Housing (Item ) PART NO 0T 0T 0T09 0T0 0T 0T DESCRIPTION Housing (Std Arrangement) Housing (Std Arrangement) Housing (Std Arrangement) ( I, D & Z ) Housing (Std Arrangement) ( I, D & Z ) Housing (Std Arrangement) (C9 Cat) Housing (Std Arrangement) (C9 Cat) Table G Output Cover/Flange (Item 0) PART NO DESCRIPTION COMPONENTS TA0 B, C & Flange/Seal Assy. Includes: T6 Bearing Cap & T7790 Output Shaft Seal TA7 D & I Flange/Seal Assembly Includes: T906 Hydraulic Flange & T779 Output Shaft Seal TA99 G Flange/Seal Assembly Includes: T97 Hydraulic Flange & T7790 Output Shaft Seal TA996 K & P Flange/Seal Assembly Includes: T7779 Hydraulic Flange & T7790 Output Shaft Seal TA997 Q & T Flange/Seal Assembly Includes: T9 Hydraulic Flange & T7790 Output Shaft Seal TA999 S Flange/Seal Assembly Includes: T6 Hydraulic Flange & T7790 Output Shaft Seal TA Z Flange/Seal Assembly Includes: T Hydraulic Flange & T779 Output Shaft Seal TA9 6 & 7 Flange/Seal Assembly Includes: T9 Hydraulic Flange & T7790 Output Shaft Seal T97 V Flange Includes: T97 Hydraulic Flange (No Shaft Seal) 6 Muncie Power Products, Inc.
INSTALLATION KITS Hose Installation Kit - TK Included with TK07 See Page for Details CS INSTALLATION KIT TK07 (V) With Direct Activation Solenoid Connect To Main Pressure Port in Transmission Red Black Green Blue 9 Activation Solenoid Metri-Pack - Type 0. Pressure Switch Metri Pack - Type 0 PTO Enable Input Wire * 6 Green Blue Ground Black Red Switch Bracket Assembly V - 0T670 V - 0T6 7 WITHOUT OVERSPEED SWITCH Rocker Switch** V DC Battery * Allison TCM (Pin ) Clutchshift PTO s require a connection to the Allison PTO Enable Input circuits. Check the vehicle dealer or body builder s information for this location.) ** Green light in the rocker switch is to turn ON when the PTO is engaged and turn OFF when the PTO is disengaged. For V Option (TK0) Include items & and substitute item with the V rocker switch (0T7). This kit also comes with the V light assembly (MSRV) and the faceplate with light access (6M0006). To Activation Solenoid To Pressure Switch PTO Enable Input Wire * SPD-00D V DC Battery Red Green WITH OVERSPEED SWITCH Blue X Green Ground Black Black Blue Orange RPM 6 Red Red White Green Blue Overspeed Light Ground 0 Black Red Installation Kit TK07 (V) ITEM QTY PART NO DESCRIPTION T699 Fuse Assembly M00 Butt Splice 6ft. 7M000 Wire M0 Female Spade Connector 7T67 Grommet 6 T090 Wire Harness 7 0T60 Pressure Switch T799 Pipe Elbow 9 T79 Pipe Nipple 0 M009 Ring Terminal M7 Female Spade Connector 6MA00 Switch Bracket 6T67 Face Plate (without Light Access) 0T67 Rocker Switch (V) N.S. 6MK007 Bolt Kit Ground 0 Rocker Switch** Switch Bracket Assembly V - 0T670 V - 0T6 Overspeed Light Face Plate with light access Overspeed Option Faceplate with light access and overspeed light are not included in 0T670 (V bracket assembly) are to be ordered separately in kit 6TK97. They are included in the V kit (TK0). Muncie Power Products, Inc. 7
INSTALLATION KITS CS Conversion Kit TK076 (V) With Remote Activation Solenoid. Use With installation Kit TK (Page 7). Hose Kit TK06 included with conversion kit (see page ). WITHOUT OVERSPEED SWITCH SHOWN Conversion Kit TK076 ITEM QTY PART NO DESCRIPTION T67 " NPT/JIC Elbow T70 " NPT/JIC Fitting TA07 Cover Assembly M60 7 6" - 0 Straight Thread Elbow T6 Straight Branch Tree 6 T79 Valve VDC 7 T67 Hose Assembly T7 Wire Harness N.S. T6 Elbow (Use as needed) N.S. 9T66 Capscrew N.S. T0 Nut N.S. T799 Lock Washer * Allison TCM (Pin ) Clutchshift PTO s require a connection to the Allison PTO Enable Input circuits. Check the vehicle dealer or body builder s information for this location.) ** Green light in the rocker switch is to turn ON when the PTO is engaged and turn OFF when the PTO is disengaged. Red Black PTO Enable Input Wire * Green Black 7 Green Blue Blue Red 7 Activation Solenoid Weather Pack Connector Rocker Switch** 6 CL EXH IN Pressure Switch Metri Pack - Type 0 7 Connect To Main Pressure Port In Transmission V DC Battery Refer to Page 7 to Install the CS Conversion Kit with an Overspeed Switch. Activation Kit CS ITEM QTY PART NO DESCRIPTION TK07 v Includes TK V kit TK0 v Includes TK9 V kit Muncie Power Products, Inc.
MODEL NUMBER CONSTRUCTION CS - A0 0 - H K X PTO Type Clutch Shift CS Mounting 0-Bolt Mount, Design 0-Bolt Mount, Design (w/remote Solenoid) 0-Bolt Mount, Special 6 Transmission CS Gear Data Allison 0.6P RH A0 Caterpillar 9.P RH C9 Speed Ratio 0 -.: 06 -.6: 07 -.7: 0 -.: 0 -.97: -.9: -.6: Shifter Type Electric/Hydraulic ( Volt) H Electric/Hydraulic ( Volt) J Less Activation Kit P Assembly Arrangement or Special Feature X None A Special SAE -Bolt B Hose Kit (HD Trans. R.S.) D Pulse Generator & SPD-00D U Pulse Generator Hose Kit Special 6" Hose Kit Special 7" Output Type B -¼" Rd; 6" KW C." 0 Spline (0 Flange) D 6mm - T (DIN 6) G Special I 6mm - T (DIN 6) K SAE B - & -Bolt 7 " - T P SAE BB - & -Bolt.0" - T Q SAE A -Bolt 7 " - T S SAE B -Bolt 7 " - T T SAE B -Bolt ¾" - T X." - 0T Spl. V For Extended Shaft Z SAE B - & -Bolt;." - T." - 0T (DIN 00 Flange) 6 SAE B -Bolt; 7 " - T 7 SAE BB -Bolt; " - T CS ARRANGEMENT CS ARRANGEMENT Assembly* Assembly Assembly Assembly *The CS hose arrangement (items, & ) should be centered over the ratio gear as shown. Muncie Power Products, Inc. 9
CS DISASSEMBLY AND REASSEMBLY (REFERENCE EXPLODED VIEWS ON PAGES, & ) DISASSEMBLY PROCEDURE. Remove the CS input gear () by removing the set screw (0) in the mounting pad and driving the idler shaft () from the housing ().. Remove the set screws (0) from the bearing cover () which hold the drag brake springs (). Position the housing so the springs can fall from the housing.. Remove the four large socket capscrews () from the bearing cover ().. Position the housing against a bench block and hit the end of the output shaft () with a soft face hammer to remove the entire output shaft assembly with the bearing cover ().. Remove the two pipe plugs () from the bearing cover () to expose the ball bearing assembly within the cover. 7 6. Using a ¼" punch and alternating between the two holes drive the bearing and output shaft assembly from the bearing cover (). 7. Using a bearing puller, remove the rear bearing () by grabbing the drag brake plate () and removing both pieces. The bronze disk () can be removed.. Remove the brake rotor using a bearing puller. 6 6 9. The piston and clutch pack may be serviced without removal of the drag brake. Using snap ring pliers, remove the snap ring (7) located on the output shaft end while gently pushing on the piston cup (6). 7 0. Pull the piston cup (6) from the shaft and the piston () will go with it.. Tap the piston cup on a wood surface to remove the piston.. Remove the spring (). The clutch friction discs (0), spacer discs () and clutch hub (9) can be removed by pointing the shaft end down.. With the drag brake removed, the snap rings ( & ) on this end of the bell gear can be removed with snap ring pliers. This allows the bell gear (6) to be removed towards the closed end. The internal bearing (7) of the bell gear can be removed. REASSEMBLY PROCEDURE. The reassembly of the unit is made in reverse of the disassembly. The re-use of seals, O-Rings and snap rings are not recommended. See page () for gasket and rebuild kits.. Be sure to lubricate all O-Rings and bearings upon installation. Torque all the capscrews to the appropriate values or to the following values: 6" Capscrews Ft.Lb.; ⅜" Capscrews 6 Ft.Lb.; ¼" Set Screw 9 Ft.Lb. 6. The input gear () is replaced as a set which includes the Base gear (6), cone spacer (7) and bearings (). Slide this sub assembly into the housing to line up the idler shaft (6). 7. Insert the shim (9) between the bearing and the housing (on the set screw side of the mounting pad). Tap the idler shaft into the housing and through the bearing races.. Tap the idler shaft in the reverse direction so that it is flush with the bearing in this assembly. Insert the thickest shim () that can be installed by hand in the gap between the bearing and housing. Remove the shim () and select the next thickest shim and drive into the gap. Rotating the gear to make sure it easily rotates. The recommended bearing pre-load is.00" to.006" loose (the cone spacer sets this pre-load and the measurement is not required). 9. Tap the idler shaft (6) into position and install the set screw (0). DROP-IN SOLENOID VALVE INSTALLATION 0. Valve is pushed into the housing cavity.. Use two mm capscrews (7) to mount the solenoid. Torque the capscrews to - Ft.Lb. DRAG BRAKE ADJUSTMENT. When installing the rear cover, be sure to align the roll pins in the drag brake plate with holes in the rear cover.. After the cover has been attached to the housing, insert the springs () into the holes.. Insert the set screw (0) over the spring and turn the screw seven (7) full turns.. Follow the test and adjustment procedures in the CS operator s manual. 6 7 6 7 0 9 9 Drag Brake Location 0 Muncie Power Products, Inc. Drag Brake Location
ACCESSORY KITS INSTALLATION HOSE KITS Hose Kit TK06 (For use with CS) ITEM QTY PART NO DESCRIPTION T67 Hose Assembly - Standard " M60 Elbow (Transmission) T6 Elbow (Use as needed) N.S. T67 Elbow N.S. T6 Tee Fitting HOSE KITS TK-Standard "; TK-Top R.S. 000 Series 7"(Optional); TK-Special 7" (optional); TK6-Top R.S. 000 Series 6" (optional) ITEM QTY PART NO DESCRIPTION T67 T67 T96 T0 Hose Assembly - Standard " Hose Assembly - HD Top 7" Hose Assembly - Special 7" Hose Assembly - HD Top 6" M60 Elbow (Transmission) T6 Elbow - Use as needed (TK & TK only) BOLT KIT SPEED SENSOR KIT OPTION U 0- Ft.Lb. 0- Ft.Lb. 0- Ft.Lb. 0- Ft.Lb. Speed Sensor Kit TK7 ITEM QTY PART NO DESCRIPTION T900 Seal Washer T60 Flat Washer T09 Jam Nut T0 Mag Pickup MA Wiring Harness CS/ Bolt Kit 0MK00 ITEM QTY PART NO DESCRIPTION 6 9T06 Pt. Capscrew - 0mm 9T777 Pt. Capscrew - mm 0T779 Alignment Stud T060 Nordlock Washer Nordlock Washer Outside Inside Mount two halves of the washer with insides facing as shown IMPORTANT: The CS includes the mounting kit, special shim/gasket, high pressure hose hookup kit, wiring harness, dash bracket kit and the installation instructions. The PTO is available with a pulse generator (pick-up) for use with the Muncie Digital Tachometer MK000 (request MP9-0) or use with the Muncie digital switch SPD-00D to control the engagement or overspeed protection of the PTO. Contact your Muncie Application Specialist for assistance with these options. SOLENOID CS V Solenoid Assembly T609 V Solenoid Assembly T67A ITEM QTY PART NO DESCRIPTION T99 Nut 7T90A 7T997A V Coil V Coil * T977 Stem T90 O-Ring N/A Manifold Back Dim A =." Dim B =.77" *Item is NOT sold separately - Ft.Lb. 0 Ft.Lb. B A Muncie Power Products, Inc.
DIMENSIONS IN INCHES (MM) B OUTPUT OPTION ¼" ROUND KEYED SHAFT 7. [.9] ¼" Round Standard Shaft. []. [6.].90 [7.7] 0." x. Woodruff Key. [.].6 7.. [.].9 [00.] 7.7 99. 0.97.6 7.6 [99.6] C OUTPUT OPTION." 0T W/ 0 SERIES FLANGE 0 Ø 0. [.] On.7" DIA B.C. PTO C L.7 0.9. 6. 0.0 7.7 Ø.6 6.." - 0T Spline Shaft 0.6. 0.0 [.] 0. 0. Ø. 60. Ø.7 69.9 Muncie Power Products, Inc.
DIMENSIONS IN INCHES (MM) D / I OUTPUT OPTION DIN 6 W/ 6MM T PTO C L.67 [.] 6.. 0.79 0 Ø 0. [.] On." DIA B.C. mm x. D Option Only 6mm - T Spline Shaft 0.9 0 0.6 6. Ø. 0. 9..0 67.0. [7] G OPTION SPECIAL W/ 7 " T. [7.] PTO C 0. L 0.6 0. 6. 6 - UNC B PLS..6 66.7 ⅞" - T Inv. Spline Shaft. [.].09 [7.7] Ø.7 69.9.9..6 66.7 Muncie Power Products, Inc.
DIMENSIONS IN INCHES (MM) K OPTION SAE B - & -BOLT W/ 7 " T P OPTION SAE B-B - & -BOLT W/ " T Z OPTION SAE B - & -BOLT W/." T PTO C L 6. [67.] 0.. ½ - UNC On.00" DIA B.C.. [0.] ½ - UNC On.7" DIA B.C. 0.0 0. 9. Inv. Spline Shaft K - ⅞" - T P - " - T Z -." - T 0.6 [6.] 0. [.] 6.6 7. " Pilot 6.. 67..9 [] Q OUTPUT OPTION SAE A -BOLT W/ 7 " T T OUTPUT OPTION SAE A -BOLT W/ ¾" T PTO C L.7 [.]. [.] 0.77 9.6 0. [6.]." Pilot ⅜ - 6 UNC On." DIA B.C. Inv. Spline Shaft Q - ⅞" - T T - ¾" - T 0. [0.7].0..67 [.] Muncie Power Products, Inc.
DIMENSIONS IN INCHES (MM) S OUTPUT OPTION SAE B -BOLT W/ 7 " T PTO C L.0 0..0 [7.] 0.6. ½ - UNC On.7" DIA B.C. " Pilot 0.9 9.9 6.7 7. 6 ⅞" - T Inv. Spline Shaft 0.9 [.].7 [.] OUTPUT OPTION." 0T W/ DIN COMPANION FLANGE PTO C L.7 [0.9]." - 0T Spline Shaft 7.6 [99.6].6 6 0.69 7. 0.0 [.9] 0.0.7 Ø.9. Ø. [7] 6XØ 0. [] On." DIA BC Ø.9 [00] Muncie Power Products, Inc.
DIMENSIONS IN INCHES (MM) 6 OUTPUT OPTION SAE B -BOLT W/ 7 " T PTO C L [0.] 6. [67.] 0. 0.0 0. ½ - UNC On.7 DIA B.C.. 9. ⅞" - T Inv. Spline Shaft 0.6 [6.] 0. [.] 6.9 76 " Pilot 6.. 67..9 [] Member of the Interpump Group SP0-0 (Rev. 07-7) 0 East Jackson Street Muncie, Indiana 70 00-67-767 Fax 76--699 info@munciepower.com www.munciepower.com Specifications are subject to change without notice. Visit www.munciepower.com for warranties and literature. All rights reserved. Muncie Power Products, Inc. (00)