Skutt Electric Kilns Skutt Kilns are known for their solid construction, energy efficient features, and reasonable pricing. They are available in a wide range of sizes and electrical configurations. Featured below are some of the most popular Skutt models. All Skutt Kilns are CSA approved and feature a rugged stainless steel jacket. The sectionalized construction gives fast access to to elements and firebricks for repair, and allows one person to transport a kiln and get through narrow doorways. For ease in firing, every KS kiln comes with an installed Kiln Sitter. For automated firing, Skutt offers the KM models with KilnMaster automatic controller. Two year limited warranty. A brochure is available for all models. Skutt KS 818-3 and KM 818-3 A good small kiln designed for the home potter or small studio loads, the 818-3 can be fired to Cone 10. Reliable and long-lasting. Features 3" firebrick for better insulating properties, faster heat build-up, and even heat distribution from top to bottom. Plugs into a standard 240V wall socket, draws 27.8 amps and 6660 watts. A 40 amp breaker is recommended. Skutt KS 1018-3 and KM 1018-3 The 1018-3 offers nearly twice the volume of the 818-3. It is a low, wide, easy-loading kiln especially designed for convenience and accessibility. Fires to Cone 10. Chamber has a 22.75" opening and is 18" deep, for a capacity of 4.38 cu. ft. Electrical requirements are 240 volts, 39.4 amps, and 9460 watts. A 50 amp.breaker is recommended. Skutt KS 1027-3 and KM 1027-3 The Cone 10 Skutt 1027-3 is the answer for large studio loads, schools, and the serious amateur who wants professional capacity. This model has chamber dimensions of 22.75" opening, 27" depth, and a capacity of 6.57 cu. ft. It draws 11520 watts at 240 volts and 48 amps. A 60 amp breaker recommended. Skutt Kilns Kilns & Accessories, Page 1
Skutt Electric Kilns Skutt KS 1227-3 and KM 1227-3 If you're looking for a full-size electric kiln, the Skutt 1227-3 will meet your needs. It has a load capacity of 9.9 cubic feet, making it ideal for schools, community centres, and professional studios. This kiln is rated to Cone 8, and has 3" firebrick. The chamber is 27" deep, has an opening of 28", and a capacity of 9.92 cu. ft. The electrical specifications are 240 volts and 48 amps for a power draw of 11520 watts. A 60 amp breaker is recommended. Skutt KS Kilns: with kiln sitter and timer Internal Dimensions Maximum Model Price Width Depth Cubic feet Cone Temp. Weight KS 818-3 $ 2175.00 16.50" 18" 2.35 10 2350 F 160 lbs. KS 1018-3 $ 3255.00 22.75" 18" 4.38 10 2350 F 275 lbs. KS 1027-3 $ 4035.00 22.75" 27" 6.57 10 2350 F 290 lbs. KS 1227-3 $ 4635.00 28.00" 27" 9.92 8 2300 F 400 lbs. Phase and Voltage Notes: Voltage: The standard electric kiln will require 240 single... phase voltage. These are the kilns we stock. Some schools and large buildings may require a 208 volt system. This is a special order from the factory, but at no extra cost. We will check your electrical requirements with you before we fill an order. Phase: Some large buildings have a three phase system. In most cases a single phase kiln can be wired into a 3 phase system. Not all Skutt kilns are available in a 3 phase version. 3 Phase mod is an additional charge. The kilns listed above are thickwalled kilns with 3" firebrick for extra insulation. They include a kiln sitter with timer as standard equipment. Note that electrical plugs are NOT included with 1027-3 and 1227-3 kiln models. For these models, Skutt suggests hard-wiring the kiln into your electrical system instead of using a plug/receptacle. Greenbarn does NOT sell the plugs separately. Replacement Skutt Peephole plugs...$7.25 Replacement Softbrick peephole plugs...$7.35 3 Phase Modification for KS Kilns...$395.00 Note: for Electrical requirements: - see 3rd page following Note: KS and/or KM1227-3 kiln. When ordered in single phase, 208 volt specification, it will fire ONLY to a max. of cone 5 due to electrical limitations. For a 1227-3 kiln that goes to cone 10, see the PK type kilns on following page. Skutt Kilns: Manual (KS) Version Kilns & Accessories, Page 2
Skutt KilnMaster Electric Kilns Since Skutt introduced their KilnMaster controller, we have found them to grow rapidly in popularity amongst all users. With the KilnMaster you get excellent temperature control, flexible firing programs, convenience, and repeatable results. Use the preset firing programs, or customize your own with the ramp/hold mode. With options to display in either Celcius or Farenheit, a programmable audible alarm, and the option to select a delay for the start of your firing, you can finish firing when it's convenient for you. All Skutt 10 and 12 sided kilns come standard with the Lid Lifter feature, and the Easy View touch pad option can be added to any KM kiln. A brochure is available. Sophisticated Cone Firing Mode Kilnmaster calculates when proper heat work has been achieved. You select the desired Cone and one of three firing speeds, depending on your load. Programmable Ramp/Hold Mode Up to 16 firing segments can control temperature change, end temperature, and holding time. Preheat and Cooling Functions Easily enter preheating segments (180*F soaks) to ensure dry ware. Cool down from your desired cone with control, new features allow you to control your rate of cooling to achieve certain glaze effects. Skutt KM1027 with factory installed KilnMaster controller Skutt KM Kilns: with automatic controller Safety & Diagnostic Features Power failture detection, thermocouple failure detection, microprocessor fault detection. New onboard diagnostic tools allow you to determine if an element needs replacing, and monitor your voltage supply. Internal Dimensions Maximum Model Price Width Depth Cubic feet Cone Temp. Weight New ~> Firebox 8x6LT $1175.00 8" x 8" 6.5".22 6 2250 F 58 lbs. (3 button control) KM-818-3 $2505.00 16.50" 18" 2.35 10 2350 F 160 lbs. KM-822-3 $2685.00 16.50" 22" 2.90 10 2350 F 180 lbs. KM-1018-3 $3425.00 22.75" 18" 4.38 10 2350 F 275 lbs. KM-1022-3 $3795.00 22.75" 22" 5.25 10 2350 F 300 lbs. KM-1027-3 $4145.00 22.75" 27" 6.57 10 2350 F 320 lbs. KM-1218-3 $4030.00 28.13" 18" 6.60 10 2350 F 330 lbs. KM-1222-3 $4390.00 27.00" 22" 8.10 10 2350 F 365 lbs. KM-1227-3 $4765.00 27.00" 27" 9.92 8 2300 F 400 lbs. KM-1227-3PK $5590.00 27.00" 27" 9.92 10 2350 F 410 lbs. KM-1231-3PK $5755.00 27.00" 31" 11.60 10 2350 F 450 lbs. KM-1627-3PK $9645.00 46 x30.75" 27" 18.50 10 2350 F 535 lbs. Options for KM Kilns: Type "S" thermocouple (per t/c)...$349.00 3 Phase Mod, KM Kilns...$70.00 Easy View Panel...$48.00 Kiln Venting...$ please see page 17 Note: KS and/or KM1227-3 kiln. When ordered in single phase, 208 volt specification, it will fire ONLY to a max. of cone 5 due to electrical limitations. For a 1227-3 kiln that goes to cone 10, see the PK type kilns on following page. Skutt Kilns: Computer (KM) Version Kilns & Accessories, Page 3
Skutt Kilns - Wall mount controllers - Separate automatic controllers: mount on the wall beside the kiln (pricing does not include CSA) KM-1 controller $ inquire - single phase, 50 amp controller - these controllers are special order items KM-1 controller $ inquire - 3 phase, 40 amp controller - these controllers are special order items Phase,Voltage, and Plug Notes: Voltage: The standard electric kiln will require 240 single... phase voltage. These are the kilns we stock. Some schools and large buildings may require a 208 volt system. This is a special order from the factory, but at no extra cost. We will check your electrical requirements with you before we fill an order. Phase: Some large buildings have a three phase system. In most cases a single phase kiln can be wired into a 3 phase system. Not all Skutt kilns are available in a 3 phase version. 3 Phase mod is an additional charge. Internal note: CLEARANCES: (recommended by U.S. manufacturer: Skutt) - 18" clearance recommended to non-combustible wall and 36" clearance recommended to combustible wall - check with your locall regulations for your local municipal requirements. - note: gyproc is rated as combustible surface. install Duroc cement board (wonderboard) 1/4" on wall to get back to 18" clearance. Note that electrical plugs are NOT included with 1027-3 and 1227-3 kiln models. For these models, Skutt suggests hard-wiring the kiln into your electrical system instead of using a plug/receptacle. We do NOT sell the plugs separately. Electrician will normally supply the plug/receptacle when installing the kiln. Skutt Kilns: Notes Kilns & Accessories, Page 4
Skutt Kilns - Electrical Specifications: 3" wall kilns Model Cone Phase Volts Amps Watts Breaker Notes KM models: automatic KM 818-3 10 single phase 240v 27.8 6660 40 amp 10 single phase 208v 26.7 5550 40 amp note: 3 phase not available on KM818-3 model KM 822-3 10 single phase 240v 33.4 8000 50 amp 10 single phase 208v 38.5 8000 50 amp note: 3 phase not available on KM822-3 model KM 1018-3 10 single phase 240v 39.4 9460 50 amp 10 single phase 208v 40.0 8320 50 amp note: 3 phase not available on KM1018-3 model KM 1022-3 10 single phase 240v 48.0 11500 60 amp 10 single phase 208v 48.0 9984 60 amp 10 3 phase 240v 34.6 11500 50 amp 10 3 phase 208v 34.6 11500 50 amp KM 1027-3 10 single phase 240v 48.0 11520 60 amp 10 single phase 208v 48.0 9980 60 amp 10 3 phase 240v 29.3 11520 40 amp 10 3 phase 208v 31.7 11000 40 amp KM 1218-3 10 single phase 240v 48.0 11500 60 amp 10 single phase 208v 48.0 9984 60 amp note: 3 phase not available on KM1218-3 model KM 1222-3 10 single phase 240v 48.0 11500 60 amp 10 single phase 208v 48.0 9984 60 amp - single phase, 208 volt is maximum cone 8 only 10 3 phase 240v 34.6 11500 50 amp 10 3 phase 208v 40.0 11500 50 amp KM 1227-3 8 single phase 240v 48.0 11520 60 amp 5 single phase 208v 48.0 9980 60 amp - single phase, 208 volt is maximum cone 5 only 8 3 phase 240v 29.3 11520 40 amp 8 3 phase 208v 31.7 11000 40 amp PK models: Production kilns KM 1227-3 PK 10 single phase 240v 60.0 14300 80 amp 10 single phase 208v 69.0 14300 90 amp 10 3 phase 240v 40.0 14300 50 amp 10 3 phase 208v 46.7 14300 60 amp KM 1231-3 PK 10 single phase 240v 72.0 17300 90 amp 10 single phase 208v 80.0 16640 100 amp 10 3 phase 240v 44.5 17300 60 amp 10 3 phase 208v 51.5 17300 70 amp KM1627PK 10 3 phase 240v 66 23600 90 amp - available 3 phase only at this time 10 3 phase 208v 76 23600 100 amp - available 3 phase only at this time note: single phase version of this kiln NOT available yet Also available: low fire version of Oval kiln: Rated to cone 1 only KM1627-3 PK-LF single phase 240v 68 16300 90 amp - fires to cone 1 only single phase 208v 69 14300 90 amp - fires to cone 1 only 3 phase 240v 46 16300 60 amp - fires to cone 1 only 3 phase 208v 47 14300 60 amp - fires to cone 1 only ZC models: Zone Control Currently available only on KM1027-3 model. Not available on KM1227-3 or on PK kilns. Electrical specifications are the same as regular versions indicated above. Note: For Copper wire sizes and NEMA receptacle configurations, please ask us or see the Skutt kiln brochure at www.skutt.com Skutt Kilns: Electrical Specifications Kilns & Accessories, Page 5
Skutt Glass Kilns - General specifications Model Price Width Depth Cu.ft Temp Weight Notes Glass kiln models: with KM controller GM 10F with door $1740.00 10"x 9" 9" 0.45 1800F 82 lb - with optional bead door GM 814 $2265.00 17.5" 13.5" 2.0 1800F 150 lb GM 818 $2450.00 17.5" 18" 2.6 1800F 147 lb GM 1014 $2560.00 23.5" 13.5" 3.5 1800F 174 lb GM 22CS $...call 23.5"x 24.5" 13.5" 4.35 1800F 257 lb - Not CSA approved GM 1018 $2965.00 23.5" 18" 4.6 1800F 196 lb GM 1414 $4145.00 41.5"x 24.5" 13.5" 6.7 1800F 241 lb - lid lifter is included with this model GM 1227-3 $4655.00 28" 27" 9.9 1800F 351 lb - lid lifter is included with this model Also available: GM 10F no door $1620.00 10"x 9" 9" 0.45 1800F 82 lb - without bead door Note: for more information, please see Skutt website at www.skutt.com Note: glass kilns are not available with kiln sitters. Available with controllers only. Note: glass kilns are rated to maximum 1800 degrees F., which is about cone 06 Note: 208 volt available on some glass kilns only. 3 phase available on some glass kilns only. Skutt Glass Kilns - Electrical Specifications Model Cone Phase Volts Amps Watts Breaker Notes Glass kiln models: with KM controller GM 10F with door 06 single phase 115v 15.0 1775 20 amp note: only available 115 volt. GM 10F no door 06 single phase 115v 15.0 1775 20 amp note: only available 115 volt. GM 814 06 single phase 240v 27.8 6660 40 amp GM 814 06 single phase 208v 32.0 6660 40 amp note: 3 phase not available on GM 814 model GM 818 06 single phase 240v 27.8 6660 40 amp GM 818 06 single phase 208v 26.7 5550 40 amp note: 3 phase not available on GM 818 model GM 1014 06 single phase 240v 34.0 8140 50 amp GM 1014 06 single phase 208v 39.1 8140 50 amp note: 3 phase not available on GM 1014 model GM 22CS 06 single phase 240v 31.0 7450 40 amp GM 22CS 06 single phase 208v 35.8 7450 40 amp GM 22CS 06 3 phase 240v 17.9 7450 30 amp GM 22CS 06 3 phase 208v 20.7 7450 30 amp GM 1018 06 single phase 240v 39.4 9460 50 amp GM 1018 06 single phase 208v 40.0 8320 50 amp note: 3 phase not available on GM 1018 model GM 1414 06 single phase 240v 34.7 8320 50 amp GM 1414 06 single phase 208v 40.0 8320 50 amp GM 1414 06 3 phase 240v 20.0 8320 30 amp GM 1414 06 3 phase 208v 23.1 8320 30 amp GM 1227-3 06 single phase 240v 48.0 11520 60 amp GM 1227-3 06 single phase 208v 48.0 9980 60 amp GM 1227-3 06 3 phase 240v 29.3 11520 40 amp GM 1227-3 06 3 phase 208v 31.7 11000 40 amp Skutt Kilns: Electrical Specifications Kilns & Accessories, Page 6