Installation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit

Similar documents
Installation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit

Installation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit

Installation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit

Installation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit

for Audi B7/A4 ( ) Part Number ES8017 Installation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit

vacuum/boost vent mounted ES best viewed in Acrobat Reader This tutorial is provided as a courtesy by ECS Tuning.

Installation. Instructions ES416. VW MKIV Golf/Jetta/GLI 337/20AE. to activate integral fog lights in Jetta GLX, E-Code, and HID Lighting Systems

MKVI Jetta Fog Light Kit

Installation MKIV Headlight Housings with Fog Lamps (Procedures apply to both MKIV Jetta and Golf)

RS5mesh style Grille. Audi A5/S5. Installation Instructions. pre-facelift ES best viewed in Acrobat Reader

MKVI Jetta Fog Light Kit

ES Installation Instructions. best viewed in Acrobat Reader. This tutorial is provided as a courtesy by ECS Tuning.

Under-Seat Storage Tray

MKV Jetta OEM Fog Installation Instructions

2010+ VW Mk6 2.0T Vent Boost Gauge Kit INSTALLATION GUIDE

MINI VIDI Integrated Digital Vent Gauge

Audi A3 8P RS4-Style Grille

ECS R32 Exhaust Flap Manual Override Installation Instructions

Installation Instructions

Audi A4 1.8T Ultimate Timing Belt Kit Installation ES#8146

Audi B9 A4 & S4 Carbon Fiber Steering Wheel Trim Installation Instructions

Installation Procedures

Installation Procedures

RS4 Style Grille. Installation. Audi B8 A4/S4 ES ES This tutorial is provided as a courtesy by ECS Tuning.

Audi A3 2.0 T FSI Fuel Pump

Bremmen Automatic Headlight Conversion Kit Installation Instructions

Audi C6 A6 RS-style Grille Installation Tutorial

ES6065 VW Golf/Jetta MKV and MKVI 2.0T Noise Pipe Bypass Duct Installation. Installation Procedures. Part Numbers: ES

Volkswagen MKVI Jetta w/keyless Start Traction Control Button Retrofit Kit Installation Instructions

Volkswagen MKVI 2.0T ECS Tuning Kohlefaser Luft-Technik System. Installation Tutorial ES ES

Installation Procedures

Audi B7 A4 2.oT Lightweight Flywheel. Installation Tutorial ES

Ziza Interior Lighting Package Installation ES

Ziza Interior Lighting Package Installation ES

Volkswagen MKIV 1.8T/2.0L/VR6 XAS Cold Air Intake System Installation

Forge 004 Dual Sprung Blow Off Valve Installation Instructions

Ziza Interior Lighting Package Installation ES

Ziza Interior Lighting Package Installation Procedures

ECS Tuning 3095 Cleveland-Massillon Rd. Norton, Ohio Phone Fax Web

Audi A Timing Belt. Installation

Ziza Interior Lighting Package Installation ES

Audi B6/B7 A4/S4 Rear Wheel Bearing Service Kit

2.0 FSI Quick Spool Crank Pulley Installation Instructions

Installation Procedures

Ziza Interior Lighting Package Installation Procedures

Audi B6/B7 A4/S4/RS4 Refrigerated Glove Box Kit. Part Number ES This tutorial is provided as a courtesy by ECS Tuning.

Toggle Button Kit. Installation Instructions MK5 / MK6 Golf, MK5 Jetta

Audi B8 A4/5, S4/5 and RS5 Coilover Installation Instructions

Volkswagen MKV/VI R32/Golf/Golf R Hatch Pop Kit

Ziza Audi A3 8V Sedan Interior lighting Kit. Installation Tutorial ES

Audi B5 A4/S4 Rear Wheel Bearing Service Kit

Conflicts - Fog Lights

Volkswagen MKVI GTI Carbon Fiber Front Diffuser Installation Instructions

GENUINE PARTS INSTALLATION INSTRUCTIONS

29048, 29049, 29050, 29051, 29052, 29053, 29054,

Ziza Interior Lighting Package Installation Procedures

CAMRY STRIP LED DRL TOYOTA Part Number: Accessory Code: LDRS10. PIO / DIO Rev. A 02/26/13. Doc

Ziza Interior Lighting Package Installation ES for BMW F10-5 Series (2011+)

29048, 29049, 29050, 29051, 29052, 29053, 29054,

29048, 29049, 29050, 29051, 29052, 29053, 29054,

INSTALLATION INSTRUCTIONS

LGT-306L / LB Club Car Precedent LED Light Bar Bumper Kit Installation Instructions

BMW N54 Kohlefaser Luft-Technik Twin Cone Intake Installation

IT IS IMPORTANT THAT YOU OBTAIN THE CORRECT INFORMATION FOR YOUR VEHICLE, OR DAMAGE TO THE WIRING SYSTEM COULD OCCUR.

29048, 29049, 29050, 29051, 29052, 29053, 29054,

Audi B5 A4/S4 B6 A4 APR Performance Chip Tune ECU Removal and Installation

Audi B7 A4 Street Shield Skid Plate Installation Instructions

INSTALLATION INSTRUCTIONS

Installation of Auto Meter Cobalt Boost/Vacuum Gauge:

M GT 2005 up Mustang ENGINE START Push-Button INSTRUCTION SHEET

TOYOTA TACOMA LED DRL. Part Number: TTA-712

INSTALLATION INSTRUCTIONS

Gentex Homelink Installation Instructions

TOYOTA TACOMA Part Number: TTA-BGB16-DRL TTA-BGP16-DRL

Remove the 3-11mm nuts holding mirror on. Don t drop the nuts!

Gentex by VOXX Corporation Installation Instructions

29048, 29049, 29050, 29051, 29052, 20953, 29054,

Depress each tab as you pull the bezel off. The bezels are tight. L.H. shown.

Part Number: TAV-713 TOYOTA AVALON LED DRL

LEXUS RC 350/RC-F ILLUMINATED DOOR SILLS Preparation

TOYOTA TACOMA XSP-X LED DRL. Part Number: Accessory Code: LDRL10

LEXUS GS 350/450h ILLUMINATED DOOR SILLS Preparation

GENUINE PARTS INSTALLATION INSTRUCTIONS

Push Start Ignition (05-10 All) Installation

Accessory Kit Estimated Fitting Time: 120 Minutes

Installation of Triple A-Pillar Pod and 7 Series Diesel Gauges Dodge Ram w/ 12 Valve Cummins Diesel Engine

Ziza Interior Lighting Package Installation Procedures

1963 GEN IV SUREFIT VINTAGE AIR CONDITIONING INSTALLATION

VW MK7 Golf/GTI/R/SportWagen S2T Aluminum Paddle Shifter Set Installation Instructions

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

INSTALLATION INSTRUCTIONS

Mercedes-Benz S203 Interior Lighting Kit Installation Guide

Ziza Interior Lighting Package Installation Procedures

Audi B5 A4 Street Shield Skid Plate Installation Instructions

Accessory Kit Estimated Fitting Time: 120 Minutes (Prado) Estimated Fitting Time: 140 Minutes (Kluger)

GENUINE PARTS INSTALLATION INSTRUCTIONS

Toggle Button Kit. Installation Instructions

STREET SH ELD. Skill Level 1 - Easy. Audi B8 Tunnel Street Shield Installation Instructions - ES Basic Skills Required

Transcription:

Installation Instructions - ECS Tuning Vent Pod Vacuum/Boost Gauge Kit This tutorial is provided as a courtesy by ECS Tuning. Part Number (also available as steering wheel mounted kit ES2593248) for VW MKV GTI TSI (2008.5+) Proper service and repair procedures are vital to the safe, reliable operation of all motor vehicles as well as the personal safety of those performing the repairs. Standard safety procedures and precautions (including use of safety goggles and proper tools and equipment) should be followed at all times to eliminate the possibility of personal injury or improper service which could damage the vehicle or compromise its safety. Although this material has been prepared with the intent to provide reliable information, no warranty (express or implied) is made as to its accuracy or completeness. Neither is any liability assumed for loss or damage resulting from reliance on this material. SPECIFICALLY, NO WARRANTY OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR ANY OTHER WARRANTY IS MADE OR TO BE IMPLIED WITH RESPECT TO THIS MATERIAL. In no event will ECS Tuning, Incorporated or its affiliates be liable for any damages, direct or indirect, consequential or compensatory, arising out of the use of this material.

Vent Pod Vacuum/Boost Gauge Installation Kit Contents: Vacuum/boost gauge Gauge power supply wiring harness Extension harness Vacuum/boost sensor (transducer with integral harness) Gauge vent pod Rigid plastic hose Braided rubber hose ECS Boost Tap Crimp bullet-style electrical connectors Crimp butt-style electrical connectors Zip ties Tools Non-marring trim removal tool Electric drill with ½-inch drill bit Wire stripper/crimp tool T20 Torx driver Work light 5mm Allen Wrench Electrical tape Page - 2

Overview - How the tutorial is organized This tutorial is broken into three sections: 1) Run the Vacuum Line - Shows how to connect the vacuum sensing line between the port on the PCV breather hose and the vacuum/boost transducer inside the cabin. 2) Install the Vent Pod and Gauge - Shows how to disassemble the dashboard vents and install the vent pod and vacuum/boost gauge. 3) Make Electrical Connections - Shows how to splice the gauge power cable to the headlight wiring harness. Section 1 - Run the vacuum line to the transducer This schematic shows kit component general locations and connections. Engine vacuum/boost is sampled at a port on the new ECS Boost Tap supplied in the kit. The small sensing hose connected to the Boost Tap is then routed through the engine compartment to a grommet in the firewall, where it enters the cabin. boost sensing transducer engine Boost Tap braided hose wire harness to boost gauge PCV hose battery tray moisture filter Page - 3 rigid line Inside the cabin, the plastic vacuum line from the engine is connected to the vacuum/boost transducer. A moisture filter is installed between the vacuum source and transducer. The transducer wiring harness is routed to the gauge later. Please route and secure all hoses, harnesses, and the transducer itself, to avoid interference with moving parts like the steering shaft and pedals.

Section 1 - Run the vacuum line Step 1 - Remove the beauty cover Install fender covers. Remove the engine beauty cover, which is held in place by plastic posts in rubber grommets. Pull straight up to free the posts from the grommets. Lay the cover aside. Step 2 - Disconnect PCV hose Disconnect the PCV hose at the intake manifold by squeezing the retainer tabs together and pulling the hose off of the intake manifold. Step 3 - Assemble Tap Apply Loctite to the pipe plug. Install the pipe plug into the upper hole as shown, using the 3mm allen wrench. Tighten the plug just until snug, do not over tighten it. Page - 4

Section 1 - Run the vacuum line Step 4 - Install Nipple Apply Loctite onto the nipple threads. Install the nipple into the lower hole. Tighten the nipple just until snug, do not over tighten it NOTE: You may need to use pliers to tighten the nipple. When doing so, be sure to protect the nipple with tape or a wrap so as not to damage it. Step 5 - Install Boost Tap Install the Boost Tap into the intake manifold by pushing it onto the intake manifold until it is completely seated. NOTE: Be sure the Boost Tap is completely seated; you could otherwise break the retainer clip during installation. Step 6 - Install Vacuum Hose Carefully push the retainer clip into place. Note the position of the Boost Tap. The nipple should angle slightly downward, as shown in the photo. This will ensure that the vacuum hose, once attached, can be routed accurately while removing the nipple from a vulnerable position. Page - 5

Section 1 - Run the vacuum line Step 7 - Run the rigid plastic line Run the rigid plastic line from the cabin to the engine compartment. There is a grommet in the far left side of the firewall behind the battery that makes a good access point (near arrow). To access the grommet, we need to remove the battery. Special Caution - Battery Safety There are several things to consider before you disconnect and remove the battery: 1) Use extreme caution when working around any battery. Wear full wrap-around safety glasses, approved for shop use. Wear gloves and protective clothing. Battery acid is highly caustic. Do not allow it come in contact with exposed skin, hair, or your eyes. 2) Battery gases are explosive. Never introduce a spark or open flame near the battery. Hydrogen gas is highly flammable, and batteries have exploded under the right circumstances. 3) Disconnecting the battery will erase keep-alive-memory data stored in the vehicle electronic control unit, car radio, and any module that stores user presets, adaptive strategies, or user preferences. Make sure you have your anti-theft radio code handy, and that you know how to use it. Store any radio station presets so you can reprogram the radio later. Do not disconnect the battery immediately before a scan tool emissions test, or you will not pass. If you are uncomfortable with these safety issues, please seek the assistance of a qualified automotive service professional. Step 8 - Remove the battery Remove the battery top and side covers. Remove the positive and negative battery cables, and battery hold down bracket, then lift the battery from the battery tray.

Section 1 - Run the vacuum line Step 9 - Run plastic line Inside the car: Remove the underdash panel from below the steering column. Working beneath the dash, run the plastic vacuum line through the firewall grommet (arrow). Inside the engine compartment: Pull the plastic line through the grommet. Step 10 - Route the line to the vacuum port Route the plastic line to the front of the engine, next to the fuel lines. Run it up to the braided hose at the vacuum port and connect the two hoses. Tie wrap the plastic line to the fuel hose. Step 11 - Connect the transducer Inside the car, use short lengths of braided rubber hose to connect the plastic vacuum line, moisture filter, and vacuum transducer in series. Mount the transducer in a safe location beneath the dash, and tie wrap it in place. Tie wrap the vacuum lines as well, keeping them clear of any moving parts like the steering column and pedals. Now we are ready to install the vent pod and gauge. Page - 7

Section 2 - Install the Vent Pod and Gauge Step 1 - Disassemble the center dash Using a non-marring trim removal tool, pry the center top grille from the dash. Pry carefully at several points until the grille panel pops free. Step 2 - Remove plate Lift and remove the stamped metal plate beneath the grille. Step 3 - Remove screws Using a T20 Torx driver, remove the three screws beneath the plate. Page - 8

Section 2 - Install the Vent Pod and Gauge Step 4 - Remove the center vent housing Lift up at the front of the dash center vent assembly. If necessary, use a flat-tipped non-marring trim removal tool to pry upward in the gap between the top of the radio and panel, releasing the tabs (arrows). Step 5 - Remove the center vent housing Lift the entire assembly out of the dash far enough to remove the emergency flasher switch and disconnect the electrical connector from the seat belt indicator light. Step 6 - Remove the radio trim surround Using the trim removal tool, pry around the edges of the trim panel surrounding the radio. Pop it free and remove it. Page - 9

Section 2 - Install the Vent Pod and Gauge Step 7 - Remove the radio Remove the four Torx screws holding the radio in place. Then slide the radio forward and rest it on the gear shift lever; do not disconnect the antenna or any radio wiring. Step 8 - Prepare the power cable Splice the extension cable to the four-wire power cable. We prefer soldering these connections and insulating them with heat shrinkable tubing. If you do not have access to a soldering iron, your kit includes four crimp-style butt connectors (see page 14 of this pdf for a detailed explanation of these connectors). Step 9 - Route the cables Route the transducer cable and power cable from the underdash area, up through the left side of the center console to the center dash opening. transducer harness gauge power harness Pull the cables through far enough to reach the area where the gauge will be installed in the vent pod. transducer power harness Page - 10

Section 2 - Install the Vent Pod and Gauge Step 10 - Remove the vent trim Remove the front trim surround from the center vent housing. Using a small screwdriver or similar tool, work your way around the perimeter, prying on the snap-lock tabs holding the sections together. Lift off the front trim. Step 11 - Remove the old vent lovers Pull/pry the vertical and horizontal vent louvers from the left side vent opening. Step 12 - Drill the harness hole Drill a ½-inch hole for the wiring harnesses, at the location shown. Page - 11

Section 2 - Install the Vent Pod and Gauge Step 13 - Install the vent pod Snap the new vent pod into the vent opening. Step 14 - Install the vent pod Reinstall the trim face on the vent assembly. Align the cover with the housing, then push them together evenly until all plastic perimeter snap-clips are engaged. Step 15 - Route harnesses Route the two harnesses through the ½-inch hole, into the vent housing, until they exit through the round hole in the vent pod. Reinstall the emergency flasher switch and reconnect the air bag light. Slide the radio back into the dash and screw it in place. Reinstall the radio trim surround. Reinstall the vent assembly with pod in the top of the dash. Page - 12

Section 2 - Install the Vent Pod and Gauge Step 16 - Install the gauge Remove the rubber band from the kit and stretch it over the gauge, as shown. Lightly lube the exterior of the band with grease or petroleum jelly. Step 17 - Install the gauge Plug the harnesses into the gauge. Plug the 3-wire transducer harness into the center receptacle. Plug the 4-wire power harness into either of the outer receptacles. Push the gauge into the pod until it sits flush. Remember to lightly lube Step 18 - Install the gauge Replace the Torx screws remove back in Step 6. Reinstall the plate and top grille removed earlier. Now it s time to make the wiring connections and test our gauge. Page - 13

Section 3 - Make Electrical Connections Step 1 - Remove and unplug the headlight switch With the headlight switch in the off position, push in on the center knob and rotate it clockwise until it stops. Then pull straight out to remove the switch from the dash. Unplug the switch from its wire harness electrical connector and lay it aside. Step 2 - Remove the fuse panel cover Using a non-marring trim removal tool, pry the at the front edge of the fuse panel cover on the left side of the dash. Remove the panel. Step 3 - Route the harnesses to the fuse panel opening Push the disconnected headlight harness back through the dashboard to the opening in the side of the dash. Route the power harness to the same opening in the dash, and make your splices. See general splicing tips and vehicle schematic on the next two pages. Page - 14

crimper ECS Tuning Vent Pod Vacuum/Boost Gauge Kit Section 3 - Make Electrical Connections Your kit contains both bullet style and butt connectors. Use the bullet connectors to splice the gauge power harness into the light switch harness. Use the butt connectors to connect the extension wire to the power harness. Directions below show how to use the connectors. Using crimp connectors 1) Cut the headlight harness wire you want to tap into. Remove enough insulation from both lengths of wire to expose a short length of wire (about 3/8-inch). 1 2 2) Insert the two lengths of bared wire into the female bullet connector. Insert the correct matching wire from the gauge harness into the male bullet connector. Note: Use a suitable wire stripper that will remove the insulation without cutting away wire strands. Use a crimping tool of the correct size, not side cutters or other pliers that may damage the insulation on the connectors. mm mm insul wire cutter 4-6 2.5 1.5 6.0 4.0 2.5 1.5 1.0 0.75 non insul wire stripper 3 3) Using a crimping tool, crimp the connector ends enough to squeeze the bare wire securely. Do not over-crimp, or you may damage the insulating collar. 4 4) Plug the two ends together. Make sure they are fully engaged. Repeat this process on the remaining wires at the headlight harness. butt connectors Use the same methods to splice the gauge power harness to the extension harness using butt connectors. See page 15 for a schematic showing component locations, electrical connections, and wire colors. Page - 15

Section 3 - Make Electrical Connections Vent Pod Vacuum Boost Gauge Wiring Connections and Component Locations MKV GTI (TSI) light switch connector light switch transducer red (keyed hot) green (dash lights) black (ground) white (B+) black/white (or black/purple) gray brown red/white power harness extension crimp connectors IMPORTANT: Vehicle wire harness colors shown here were taken from a test car. Due to changes in color production coding and field modifications, we cannot guarantee an exact color match to your vehicle harness. When in doubt, please use the generic values listed for the gauge harness, and match them to the correct harness wires in your car. Use a test light or voltmeter to locate the correct wires. red = keyed hot black = ground green = dash lights white = battery hot (B+) Finishing Up Splice the power and headlight harnesses using the bullet connectors in the kit. Reinstall and reconnect the battery, battery hold down, and covers. Test the gauge. When you switch the ignition on, your vacuum/boost gauge should go through an initialization process: it will sweep from full vacuum to full boost, and then settle back to zero before your engine starts. Your gauge backlight should illuminate and respond to changes in your dash light dimmer settings. Page - 16

Finishing up Testing and Reassembly: When you are sure the gauge is working properly, replace the fuse cover, lower and underdash panels, and headlight switch. Slide the headlight switch into the dash until it snaps in place. Thanks! Thank you for purchasing the ECS Tuning Vent Pod Vacuum/Boost Gauge. We appreciate your business, and hope this installation guide has been helpful. ECS Tuning also sells a steering column mounted gauge set, visible through the steering wheel ES2593248 Page - 17